Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Kinetic and microbiological characterization of aerobic granules performing partial nitritation of a low-strength wastewater at 10ºC

  • Reino, Clara|||0000-0003-3378-3542
  • Suárez Ojeda, María Eugenia|||0000-0003-2520-2701
  • Pérez Cañestro, Julio|||0000-0002-0119-5570
  • Carrera, Julian|||0000-0002-2599-2312
A granular airlift reactor enriched in ammonia oxidizing bacteria (AOB) was operated at 10 °C performing stable partial nitritation in the long-term. The reactor treated a synthetic low-strength influent during 250 days with an average nitrogen loading rate of 0.63 ± 0.06 g N L⁻¹ d⁻¹. Nitrate production was barely detected, being the average concentration in the effluent of 0.6 ± 0.3 mg N-NO3 L⁻¹. Furthermore, a suitable effluent for a subsequent reactor performing the anammox process was achieved. A maximum specific growth rate as high as 0.63 ± 0.05 d⁻¹ was determined by performing kinetic experiments with the granular sludge in a chemostat and fitting the results to the Monod model. Pyrosequencing analysis showed a high enrichment in AOB (41 and 65% of the population were identified as Nitrosomonas genus on day 98 and 233, respectively) and an effective repression of nitrite oxidizing bacteria in the long-term. Pyrosequencing analysis also identified the coexistence of nitrifying bacteria and heterotrophic psychrotolerant microorganisms in the granular sludge. Some psychrotolerant microorganisms are producers of cryoprotective extracellular polymeric substances that could explain the better survival of the whole consortia at cold temperatures.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Long-term performance and stability of a continuous granular airlift reactor treating a high-strength wastewater containing a mixture of aromatic compounds

  • Ramos Quiroz, Carlos Antonio|||0000-0002-6683-7175
  • Suárez Ojeda, María Eugenia|||0000-0003-2520-2701
  • Carrera, Julian|||0000-0002-2599-2312
Continuous feeding operation of an airlift reactor and its inoculation with mature aerobic granules allowed the successful treatment of a mixture of aromatic compounds (p-nitrophenol, o-cresol and phenol). Complete biodegradation of p-nitrophenol, o-cresol, phenol and their metabolic intermediates was achieved at an organic loading rate of 0.61 g COD L⁻¹ d⁻¹. Stable granulation was obtained throughout the long-term operation (400 days) achieving an average granule size of 2.0±1 mm and a sludge volumetric index of 26±1 mL g⁻¹ TSS. The identified genera in the aerobic granular biomass were heterotrophic bacteria able to consume aromatic compounds. Therefore, the continuous feeding regimen and the exposure of aerobic granules to a mixture of aromatic compounds make possible to obtain good granulation and high removal efficiency.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Long-term impact of salinity on the performance and microbial population of an aerobic granular reactor treating a high-strength aromatic wastewater

  • Ramos Quiroz, Carlos Antonio|||0000-0002-6683-7175
  • Suárez Ojeda, María Eugenia|||0000-0003-2520-2701
  • Carrera, Julian|||0000-0002-2599-2312
The effect of salinity over granular biomass treating a mixture of aromatic compounds (phenol, o-cresol and p-nitrophenol) was evaluated in a continuous airlift reactor. To mimic an industrial wastewater, increasing concentrations (from 2.0 to 29.0 g salts L⁻¹) of a mixture of salts (MgSO₄, NaCl, KCl, CaCl₂ and NaHCO₃) were introduced in the influent. The gradual salinity increase led to a good acclimation of the biomass obtaining complete biodegradation of the aromatic compounds and no accumulation of metabolic intermediates. However, a deterioration of the morphology of aerobic granules with a complete loss of granulation after 125 days was produced at 29.0 g salts L⁻¹. At that moment, anaerobic granules were added to promote granulation and after 50 days new aerobic granules were formed. These new aerobic granules remained stable for more than 100 days at the highest salinity condition with 100% removal of the mixture of aromatic compounds.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Effect of temperature on N₂O emissions from a highly enriched nitrifying granular sludge performing partial nitritation of a lowstrength wastewater

  • Reino, Clara|||0000-0003-3378-3542
  • Van Loosdrecht, Mark C. M.
  • Carrera, Julian|||0000-0002-2599-2312
  • Pérez Cañestro, Julio|||0000-0002-0119-5570
In the race to achieve a sustainable urban wastewater treatment plant, not only the energy requirements have to be considered but also the environmental impact of the facility. Thus, nitrous oxide (N₂O) emissions are a key-factor to pay attention to, since they can dominate the total greenhouse gases emissions from biological wastewater treatment. In this study, N2O production factors were calculated during the operation of a granular sludge airlift reactor performing partial nitritation treating a low-strength synthetic influent, and furthermore, the effect of temperature on N₂O production was assessed. Average gas emission relative to conversion of ammonium was 1.5 ± 0.3% and 3.7 ± 0.5% while the effluent contained 0.5 ± 0.1% and 0.7 ± 0.1% (% N-oxidized) at 10 and 20 ºC, respectively. Hence, temperature increase resulted in higher N2O production. The reasons why high temperature favoured N₂O production remained unclear, but different theoretical hypotheses were suggested.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Low-strength wastewater treatment in an anammox UASB reactor, effect of the liquid upflow velocity

  • Reino, Clara|||0000-0003-3378-3542
  • Carrera, Julian|||0000-0002-2599-2312
Two-stage systems have been proposed to overcome the drawbacks associated to the implementation of the autotrophic biological nitrogen removal process in the mainstream of urban wastewater treatment plants. In this study, an upflow anammox sludge blanket (UAnSB) reactor was successfully operated for 325 days treating a low-strength synthetic influent mimicking mainstream conditions. A nitrogen loading rate of up to 1.8 ± 0.2 g N L⁻¹ d⁻¹ was achieved at 26 ºC and the nitrogen removal rate obtained (1.7 ± 0.1 g N L⁻¹ d⁻¹) resulted considerably higher than most of the previously reported values for systems treating low-strength wastewater at similar temperatures. Fluorescence in situ hybridization analysis showed a high enrichment in the anammox specie Candidatus Brocadia anammoxidans during the whole operation. The evolution of the granule diameter was followed throughout the operation of the UAnSB reactor and a direct correlation of the average granule diameter with the liquid upflow velocity (Vup) was established, being the higher the Vup, the bigger the granules. A stable granule diameter of 790 ± 40 μm was achieved by maintaining a Vup of 1.0 ± 0.1 m h⁻¹. The low VupS applied avoid the use of effluent recirculation which would present a huge inconvenient to implement UAnSB reactors at real scale, however these low VupS led to external mass transfer problems in the reactor. In spite of the mass transfer limitations, not only a high specific anammox activity (0.26 ± 0.02 g N g⁻¹ VS d⁻¹) was achieved in the UASB reactor but also a high nitrogen removal (80 ± 3%).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Inkjet-Printed Sulfide-Selective Electrode

  • Pol, Roberto|||0000-0002-4387-4061
  • Moya Lara, Ana|||0000-0001-6793-9133
  • Gabriel, Gemma|||0000-0003-2140-6299
  • Gabriel, David|||0000-0002-7713-4192
  • Céspedes, Francisco|||0000-0002-0296-6314
  • Baeza, Mireia|||0000-0002-2240-6410
Inkjet printing technology has emerged as an alternative manufacturing method for low-cost production of electrodes. Despite significant progress, there is still a lack in the production of ion-selective electrodes. Herein, the two-step fabrication of the first inkjet-printed sulfide-selective electrode (IPSSE) is described. The two-step fabrication consists of printing a silver electrode followed by an electrochemical deposition of sulfide to produce a second kind electrode (Ag/Ag2S). The performance of this novel device was tested using potentiometric measurements. Nernstian response (-29.4 ± 0.3 mV·decade-1) was obtained within concentrations of 0.03-50 mM with a response time of ∼3 s. Furthermore, river/sea-spiked environmental samples and samples from a bioreactor for sulfate reduction to sulfide were measured and compared against a commercial sensor giving no significant differences. The IPSSE described in this work showed good reproducibility and durability during daily measurements over 15 days without any special storage conditions. Considering all the current challenges in inkjet-printed ion-selective electrodes, this different fabrication approach opens a new perspective for mass production of all-solid state ion-selective electrodes.