Pasar al contenido principal

DESARROLLO DE UN PROCESO INTEGRAL DE TRATAMIENTO DE SOX Y NOX PROCEDENTES DE GASES DE COMBUSTION ORIENTADO A SU VALORIZACION

CTQ2015-69802-C2-1-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDAD AUTONOMA DE BARCELONA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Inkjet-Printed Sulfide-Selective Electrode

  • Pol, Roberto
  • Moya, Ana
  • Gabriel, Gemma
  • Gabriel, David
  • Céspedes, Francisco
  • Baeza, Mireia
Inkjet printing technology has emerged as an alternative manufacturing method for low-cost production of electrodes. Despite significant progress, there is still a lack in the production of ion-selective electrodes. Herein, the two-step fabrication of the first inkjet-printed sulfide-selective electrode (IPSSE) is described. The two-step fabrication consists of printing a silver electrode followed by an electrochemical deposition of sulfide to produce a second kind electrode (Ag/Ag2S). The performance of this novel device was tested using potentiometric measurements. Nernstian response (-29.4 ± 0.3 mV·decade-1) was obtained within concentrations of 0.03-50 mM with a response time of ∼3 s. Furthermore, river/sea-spiked environmental samples and samples from a bioreactor for sulfate reduction to sulfide were measured and compared against a commercial sensor giving no significant differences. The IPSSE described in this work showed good reproducibility and durability during daily measurements over 15 days without any special storage conditions. Considering all the current challenges in inkjet-printed ion-selective electrodes, this different fabrication approach opens a new perspective for mass production of all-solid state ion-selective electrodes., R.P. would like to acknowledge Universitat Autònoma de Barcelona (UAB) for the PIF grant. Authors would also like to thank the financial support from the CTQ2015-69802-C2-1-R research project from the Spanish Ministerio de Economía y Competitividad y Fondo Europeo de Desarrollo Regional (MINECO/FEDER, UE). Authors also want to thank the support of the Generalitat de Catalunya to GENOCOV (2014-SGR-1255). Authors acknowledge ICTS NANBIOSIS more specifically by the SU-8 Unit of the CIBER in Bioengineering, Biomaterials & Nanomedicine (CIBER-BBN) at the IMB-CNM (CSIC). This work has also made use of the Spanish ICTS Network MICRONANOFABS partially supported by MEINCOM., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

All-inkjet-printed dissolved oxygen sensors on flexible plastic substrates

  • Moya, Ana
  • Sowade, Enrico
  • del Campo, Francisco J.
  • Mitra, Kalyan Y.
  • Ramon, Eloi
  • Villa, Rosa
  • Baumann, Reinhard R.
  • Gabriel, Gemma
Inkjet printing is a promising alternative manufacturing method to conventional standard microfabrication techniques for the development of flexible and low-cost devices. Although the use of inkjet printing for the deposition of selected materials for the development of sensor devices has been reported many times in literature, it is still a challenge and a potential route towards commercialization to completely manufacture sensor devices with inkjet technology. In this work is demonstrated the fabrication of a functional low-cost dissolved oxygen (DO) amperometric sensor with feature sizes in the micrometer range using inkjet printing. All the required technological steps for the fabrication of a complete electrochemical three electrodes system are discussed in detail. The working and counter electrodes have been printed using a gold nanoparticle ink, whereas a silver nanoparticle ink was used to print a pseudo-reference electrode. Both inks are commercially available and can be sintered at low temperatures, starting already at 120 °C, which allows the use of plastic substrates. In addition, a printable SU8 ink formulation cured by UV is applied as passivation layer in the sensor device. Finally, as the performance of analytical methods strongly depends on the working electrode material, is demonstrated the electrochemical feasibility of this printed DO sensor, which shows a linear response in the range between 0 and 8 mg L<sup>−1</sup> of DO, and affords a detection limit of 0.11 mg L<sup>−1</sup>, and a sensitivity of 0.03 μA L mg<sup>−1</sup>. The use of flexible plastic substrates and biocompatible inks, and the rapid prototyping and low-cost of the fabricated sensors, makes that the proposed manufacturing approach opens new opportunities in the field of biological and medical sensor applications., This work was supported by the Ministerio de Economía y Competitividad [CTQ2015-69802-C2-1-R and DPI2015-65401-C3-3-R]; and the Generalitat de Catalunya [2014SGR1452]. The authors kindly acknowledge Christoph Sternkiker (TU Chemnitz, Digital Printing and Imaging Technology) for his support with inkjet printing and measuring of surface energy. A.M. gratefully acknowledges her FPI-2012 pre-doctoral scholarship, (it funded her PhD studies at Universitat Autònoma de Barcelona) and the mobility aid [EEBB-I-15-09362], (it financed her four-months stay at the TU Chemnitz, Department of Digital Printing and Imaging Technology) both granted by the Ministerio de Economía y Competitividad (Spain). The authors also acknowledge ICTS “NANBIOSIS”, more specifically by the SU8 Unit of the CIBER in Bioengineering, Biomaterials & Nanomedicne (CIBER-BBN) at the IMB-CNM (CSIC)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Inkjet-printed electrochemical sensors

  • Moya, Ana
  • Gabriel, Gemma
  • Villa, Rosa
  • Javier del Campo, F.
Inkjet printing is a digital and non-contact printing technique that is beginning to be used in the manufacture of electronic devices, including electrochemical sensors. This article covers the main works featuring inkjet printing for the production of electrochemical sensors, and focuses especially on the works reported since 2015. The main factor limiting the application of inkjet printing in the manufacture of advanced devices stems mainly from the strict rheological conditions that the ink needs to meet. This is the reason why inkjet is best used in combination with other manufacturing techniques. Given their high degree of maturity and accessibility, home/office printers will likely lead a future wave in the manufacture of electronic devices, particularly at the development and prototyping stages., The authors would like to acknowledge funding from the Spanish Ministry of Economy and Competitiveness through project grants CTQ2015-69802-C2-1-R, CTQ2015-69802-C2-1-R, and DPI2015-65401-C3-3-R MINECO/FEDER, EU. JdC acknowledges a grant for Researchers and Cultural Creators (2016) from the BBVA Foundation. The authors are grateful to Mr. Ignasi Riera, from INKZAR S.L., for fruitful discussions., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced Performance Stability of Iridium Oxide-Based pH Sensors Fabricated on Rough Inkjet-Printed Platinum

  • Zea, Miguel
  • Moya, Ana
  • Fritsch, Marco
  • Ramon, Eloi
  • Villa, Rosa
  • Gabriel, Gemma
Today, electrochemical sensors are used for a broad range of applications. A fundamental challenge is still the achievement of long-term sensor stability by ensuring good adhesion between the deposited sensing layer and the substrate material, e.g., a metal electrode. Until now, the most applied strategy to overcome this problem is to increase the surface roughness of the metal layer by mechanical etching or by electroplating of additional material layers, which both imply an increase in manufacturing steps and thus the final cost of the overall device. Alternatively, to overcome these adhesion problems, we propose the direct printing of a novel platinum nanoparticle ink, which is compatible with low-cost additive digital inkjet and with flexible low-cost substrates. This water-based platinum ink has two unique features: it leads to highly rough surfaces, which promotes the adhesion of deposited sensing material, and it is a highly low-temperature curing ink, compatible with polymeric substrates that cannot withstand high temperatures. Based on this concept, we report about a long-term stable and highly sensitive solid-state pH sensor functionalized by anodic electrodeposited iridium oxide on a rough nanostructured platinum printed layer. The sensors showed an excellent reproducibility with a linear super-Nernstian response (71.3 ± 0.3 mV/pH unit) in a wide pH range (pH 2-11). Long-term stability tests for over 1 year of application demonstrate an excellent mechanical sensor layer stability, which is correlated to the distinct roughness of the printed platinum layer. This novel approach is useful to simplify the fabrication process and with that the sensor costs., M.Z. acknowledges financial support covered by Fundación Centro de Estudios Interdisciplinarios Bá sicos y Aplicados (CEIBA)-Gobernacion de Bolivar (Colombia). This work was supported by the Spanish government funded project by Ministerio de Economí a y Competitividad CTQ2015-69802-C2-1-R (MINECO/FEDER, EU) and DPI2015-65401-C3-3-R (MINECO/FEDER, EU). Authors also want to thank the support of the Generalitat de Catalunya to 2017-SGR-988, and the SU-8 Unit of the CIBER in Bioengineering, Biomaterials and Nanomedicine (CIBER-BBN) at the IMB-CNM (CSIC) of ICTS “NANBIOSIS”. This work has also made use of the Spanish ICTS Network MICRONANOFABS partially sup-ported by MEINCOM, Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrochemical Biosensor Based on Optimized Biocomposite for Organophosphorus and Carbamates Pesticides Detection

  • Montes, Raquel|||0000-0001-8805-9987
  • Céspedes, Francisco|||0000-0002-0296-6314
  • Gabriel, David|||0000-0002-7713-4192
  • Baeza, Mireia|||0000-0002-2240-6410
This paper presents the characterization and optimization of biosensors based on graphite-epoxy which incorporates the enzyme acetylcholinesterase (AChE). By means of advanced electrochemical techniques, such as electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), the characterization and optimization of graphite-epoxy-AChE biosensors have been performed. In order to obtain sensitive electrodes, the optimal composition of the transducer material (graphite-epoxy-enzyme ratio) was studied. The optimization of the conductive particles distribution inside the biomaterial has allowed an improvement of the electrochemical properties. Optimal composition guarantees improving electrochemical properties required, such as high electron-transfer rate, high signal-to-noise ratio, and suitable sensitivity. The optimal biocomposite composition range was obtained between 16% and 17% of graphite and 0.12% of AChE. The biosensors were applied to the analysis of different pesticides, organophosphorus and carbamates, using indirect measurements based on enzymatic inhibition process. These optimized biosensors present detection limit one order of magnitude lower compared to the standard composition (nonoptimized) and allow achieving concentrations lower than the established ones by the pesticides regulation. Finally, spiked tap water samples with pesticides were analyzed with the optimized biosensors.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A minimally invasive microsensor specially designed for simultaneous dissolved oxygen and pH biofilm profiling

  • Guimerà Villalba, Xavier|||0000-0002-4156-2988
  • Moya Lara, Ana|||0000-0001-6793-9133
  • Dorado, Antonio David|||0000-0003-0238-5867
  • Illa, Xavi|||0000-0002-3212-1128
  • Villa, Rosa|||0000-0003-2735-3204
  • Gabriel, David|||0000-0002-7713-4192
  • Gamisans Noguera, Xavier|||0000-0003-1856-8692
  • Gabriel, Gemma|||0000-0003-2140-6299
A novel sensing device for simultaneous dissolved oxygen (DO) and pH monitoring specially designed for biofilm profiling is presented in this work. This device enabled the recording of instantaneous DO and pH dynamic profiles within biofilms, improving the tools available for the study and the characterization of biological systems. The microsensor consisted of two parallel arrays of microelectrodes. Microelectrodes used for DO sensing were bare gold electrodes, while microelectrodes used for pH sensing were platinum-based electrodes modified using electrodeposited iridium oxide. The device was fabricated with a polyimide (Kapton®) film of 127 µm as a substrate for minimizing the damage caused on the biofilm structure during its insertion. The electrodes were covered with a Nafion® layer to increase sensor stability and repeatability and to avoid electrode surface fouling. DO microelectrodes showed a linear response in the range 0-8 mg L˗1, a detection limit of 0.05 mg L-1, and a sensitivity of 2.06 nA L mg-1. pH electrodes showed a linear super-Nernstian response (74.2 ± 0.7 mV/pH unit) in a wide pH range (pH 4-9). The multi-analyte sensor array was validated in a flat plate bioreactor where simultaneous and instantaneous pH and DO profiles within a sulfide oxidizing biofilm were recorded. The electrodes spatial resolution, the monitoring sensitivity, and the minimally invasive features exhibited by the proposed microsensor improved biofilm monitoring performance, enabling the quantification of mass transfer resistances and the assessment of biological activity.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Inkjet-Printed Sulfide-Selective Electrode

  • Pol, Roberto|||0000-0002-4387-4061
  • Moya Lara, Ana|||0000-0001-6793-9133
  • Gabriel, Gemma|||0000-0003-2140-6299
  • Gabriel, David|||0000-0002-7713-4192
  • Céspedes, Francisco|||0000-0002-0296-6314
  • Baeza, Mireia|||0000-0002-2240-6410
Inkjet printing technology has emerged as an alternative manufacturing method for low-cost production of electrodes. Despite significant progress, there is still a lack in the production of ion-selective electrodes. Herein, the two-step fabrication of the first inkjet-printed sulfide-selective electrode (IPSSE) is described. The two-step fabrication consists of printing a silver electrode followed by an electrochemical deposition of sulfide to produce a second kind electrode (Ag/Ag2S). The performance of this novel device was tested using potentiometric measurements. Nernstian response (-29.4 ± 0.3 mV·decade-1) was obtained within concentrations of 0.03-50 mM with a response time of ∼3 s. Furthermore, river/sea-spiked environmental samples and samples from a bioreactor for sulfate reduction to sulfide were measured and compared against a commercial sensor giving no significant differences. The IPSSE described in this work showed good reproducibility and durability during daily measurements over 15 days without any special storage conditions. Considering all the current challenges in inkjet-printed ion-selective electrodes, this different fabrication approach opens a new perspective for mass production of all-solid state ion-selective electrodes.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Exploring the performance limits of a sulfidogenic UASB during the long-term use of crude glycerol as electron donor

  • Fernandez Palacios, Eva|||0000-0002-0095-220X
  • Lafuente Sancho, Francisco Javier|||0000-0002-4601-9001
  • Mora Garrido, Mabel|||0000-0002-2979-3601
  • Gabriel, David|||0000-0002-7713-4192
SOx contained in flue gases and S-rich liquid effluents can be valorized to recover elemental sulfur in a two-stage bioscrubbing process. The reduction of sulfate to sulfide is the most crucial stage to be optimized. In this study, the long-term performance of an up-flow anaerobic sludge blanket (UASB) reactor using crude glycerol as electron donor was assessed. The UASB was operated for 400 days with different sulfate and organic loading rates (SLR and OLR, respectively) and a COD/S-SO42- ratio ranging from 3.8 g O2 g-1 S to 5.4 g O2 g-1 S. After inoculation with methanogenic, granular biomass, the competition between sulfate-reducing and methanogenic microorganisms determined to what extent dissolved sulfide and methane were produced. After the complete washout of methanogens, which was revealed by next-generation sequencing analysis, the highest S-EC was reached in the system. The highest average sulfate elimination capacity (S-EC = 4.3 kg S m-3d-1) was obtained at a COD/S-SO42- ratio of 5.4 g O2 g-1 S and an OLR of 24.4 kg O2 m-3d-1 with a sulfate removal efficiency of 94%. The conversion of influent COD to methane decreased from 12% to 2.5% as the SLR increased while a large fraction of acetate (35% of the initial COD) was accumulated. Our data indicate that crude glycerol can promote sulfidogenesis. However, the disappearance of methanogens in the long-term due to the out competition by sulfate reducing bacteria, lead to such large accumulation of acetate.