Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Improving thermal performance of freezers using phase change materials, Amélioration de la performance thermique des congélateurs à l’aide de matériaux à changement de phase

  • Oró Prim, Eduard
  • Miró, Laia
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Food transport and storage at low temperatures is a matter worldwide due to changes of the dietary habits and the increasing of the population. The issue of improving food storage applies at different applications such as commercial freezers or refrigerated trucks. The aim of this work is to improve the thermal performance of commercial freezers using phase change materials (PCMs) under door openings and electrical power failure. A commercial PCM was selected (Climsel-18) with a melting temperature of -18 ºC, which is contained in 10 mm thick stainless steel panels placed at different locations in the freezer. During 3 h of electrical power failure, the use of PCM maintained the freezer temperature 4-6 ºC lower and that of the frozen products remains at acceptable levels for much longer time. With frequent door openings the benefit of the PCM is evident when the temperature of the cabinet is near the melting temperature of the PCM., The work was partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF-/-253914)
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Life Cycle Assessment of experimental cubicles including PCM manufactured from natural resources (esters): a theoretical study

  • Menoufi, Karim Ali Ibrahim
  • Castell, Albert
  • Farid, Mohammed M.
  • Boer, Dieter
  • Cabeza, Luisa F.
Among the research activities that aim at reducing energy consumption in buildings and their impact on the environment is an experimental set-up that has several house-shaped cubicles constructed in Puigverd de Lleida (Spain). Assessing the environmental impact through studying the manufacturing, operational and disposal phases of these cubicles have been done in previous research. The objective of this paper is to investigate the use of esters as PCM in order to estimate its environmental impact in building envelopes in comparison to the use of paraffin or salt hydrates through a theoretical study. The evaluation of the environmental impact of this type of PCM material is conducted using Life Cycle Assessment (LCA) based on the Eco-indicator 99 method. It is found that the impact of ester used as PCM presents slightly better results than the case of using salt hydrates during the manufacturing impact. On the other hand, the use of salt hydrates or ester as PCM in the cubicles results in an impact reduction of 9% and 10.5% respectively, compared to the case of using paraffin., The work was partially funded by the Spanish government (projects ENE2008-06687-C02-01/CON and DPI2008-04099/DPI) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF −/− 253914)
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Review on phase change materials (PCMs) for cold thermal energy storage applications

  • Oró Prim, Eduard
  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Thermal energy storage (TES) is a technology with a high potential for different thermal applications. It is well known that TES could be the most appropriate way and method to correct the gap between the demand and supply of energy and therefore it has become a very attractive technology. In this paper, a review of TES for cold storage applications using solid–liquid phase change materials has been carried out. The scope of the work was focussed on different aspects: phase change materials (PCMs), encapsulation, heat transfer enhancement, and the effect of storage on food quality. Materials used by researchers as potential PCM at low temperatures (less than 20 C) are summarized and some of their thermophysical properties are reported. Over 88 materials that can be used as PCM, and about 40 commercially available PCM have been listed. Problems in long term stability of the materials, such as corrosion, phase segregation, stability under extended cycling or subcooling are discussed. Heat transfer is considered both from theoretical and experimental point of view and the different methods of PCM encapsulation are reviewed. Many applications of PCM at low temperature can be found, such as, ice storage, conservation and transport of temperature sensitive materials and in air conditioning, cold stores, and refrigerated trucks., The work partially funded by the Spanish Government (ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF-/-253914). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534). Eduard Oró would like to thank the University of Lleida for his research fellowship.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal analysis of including phase change material in a domestic hot water cylinder

  • Gracia Cuesta, Alvaro de
  • Oró Prim, Eduard
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
The domestic electrical hot water cylinder used in this paper incorporates encapsulated phase change material (PCM) placed in 57 vertical pipes. The use of PCM increases the thermal energy storage capacity of the cylinder and allows the use of low cost electricity during low peak periods. The operational mode of the system is based on heating the water and melting the phase change material during night. After first discharge of hot water, the phase change material will transfer heat to the recently introduced cold water and increase its temperature without using electricity. The already measured experimental data prove the efficiency of the use of PCM in these systems and are used to validate a developed code for numerical simulation using finite volume method. Following model validation a parametrical study was carried out to optimize the PCM distribution inside the hot water cylinder., The work partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS - FP7-PEOPLE-2009-IIF -/- 253914). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534)., MICINN/PN2008-2011/ENE2008-06687-C02-01/CON
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Corrosion of metal and polymer containers for use in PCM cold storage

  • Oró Prim, Eduard
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Transport and storage of low temperature sensitive products is an issue worldwide due to changes of the lifestyle and population increase. In the recent years, thermal energy storage (TES) using phase change materials (PCMs) is being highly studied and developed for cold storage applications. Furthermore, the PCM are normally encapsulated in containers and added in the available systems, usually in food processes. Therefore safety constraints as the compatibility of the PCM with other materials have to take into account. Hence the main goal of the paper is to study the corrosion effect of different metals and polymer materials in contact with some PCM used in low temperature applications. Results show that copper and carbon steel must be avoided as PCM containers, and aluminium is not recommended; stainless steel 316 is recommended when in contact with the tested PCM. Moreover, PP, PS, PET, and HDPE are not affected by a process of degradation and are also compatible with the PCM studied., The work is partially funded by the Spanish Government (ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (EFFIBUILDINGS). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534). Eduard Oró would like to thank University of Lleida for his research fellowship.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

New equipment for testing steady and transient thermal performance of multilayered building envelopes with PCM

  • Gracia Cuesta, Alvaro de
  • Barreneche Güerisoli, Camila
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Thermal properties of the different building envelopes, such as thermal transmittance in steady state, heat storage capacity and dynamic thermal responses, must be taken into account during the design phase of buildings. The evaluation and measurement of these parameters in multilayered samples are difficult because of the irregular morphology of the used materials and the difficulty in providing the well-controlled environment needed for the measurements. A new equipment has been designed to measure the thermal response and heat capacity of composite walls of different materials simulating real building envelopes. The equipment presented in this paper was used to test the improvement in the thermal response of a building envelope due to the incorporation of PCM. This study is focused on wood structural panels attached to a gypsum board, which is either impregnated or not with PCM. The four edges of the composite sample are properly insulated to ensure one-dimensional heat flow. The two faces of the sample are exposed to controlled environments heated and cooled by copper coils with thermo stated water supplied by water baths. The measured surface heat fluxes at both surfaces of the sample and temperature distribution in the sample provide accurate assessment to thermal mass and dynamic response of the composite wall, while the steady state measurements provide an accurate estimate of its effective thermal transmittance., The work partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS - FP7-PEOPLE-2009-IIF -/- 253914)
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Analysis of implementing phase change materials in open-air swimming pools

  • Zsembinszki, Gabriel
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Open-air swimming pools in Mediterranean climate regions are heated by direct solar radiation with no auxiliary heating systems. In order to extend the swimming season or improve comfort conditions, solar collectors or pool coverings may be used. In this paper, another approach was followed through the use of phase change materials (PCM). Two methods of introducing the PCM were considered: (1) encapsulated in the sidewalls and bottom of the pool, and (2) use the PCM in an external heat exchanger. Heat is stored when water temperature is sufficiently high, while it is released when water temperature drops below comfort levels. A numerical model was built and validated for predicting the evolution of the water temperature, by taking into account meteorological data at three different locations in north-east of Spain. The simulations showed that using phase change materials provided some improvement of water conditions, especially when used in an external heat exchanger., The work was partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS - FP7-PEOPLE-2009-IIF -/- 253914).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Improving thermal performance of freezers using phase change materials, Amélioration de la performance thermique des congélateurs à l’aide de matériaux à changement de phase

  • Oró Prim, Eduard
  • Miró, Laia
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Food transport and storage at low temperatures is a matter worldwide due to changes of the dietary habits and the increasing of the population. The issue of improving food storage applies at different applications such as commercial freezers or refrigerated trucks. The aim of this work is to improve the thermal performance of commercial freezers using phase change materials (PCMs) under door openings and electrical power failure. A commercial PCM was selected (Climsel-18) with a melting temperature of -18 ºC, which is contained in 10 mm thick stainless steel panels placed at different locations in the freezer. During 3 h of electrical power failure, the use of PCM maintained the freezer temperature 4-6 ºC lower and that of the frozen products remains at acceptable levels for much longer time. With frequent door openings the benefit of the PCM is evident when the temperature of the cabinet is near the melting temperature of the PCM., The work was partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF-/-253914)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Life Cycle Assessment of experimental cubicles including PCM manufactured from natural resources (esters): a theoretical study

  • Menoufi, Karim Ali Ibrahim
  • Castell, Albert
  • Farid, Mohammed M.
  • Boer, Dieter
  • Cabeza, Luisa F.
Among the research activities that aim at reducing energy consumption in buildings and their impact on the environment is an experimental set-up that has several house-shaped cubicles constructed in Puigverd de Lleida (Spain). Assessing the environmental impact through studying the manufacturing, operational and disposal phases of these cubicles have been done in previous research. The objective of this paper is to investigate the use of esters as PCM in order to estimate its environmental impact in building envelopes in comparison to the use of paraffin or salt hydrates through a theoretical study. The evaluation of the environmental impact of this type of PCM material is conducted using Life Cycle Assessment (LCA) based on the Eco-indicator 99 method. It is found that the impact of ester used as PCM presents slightly better results than the case of using salt hydrates during the manufacturing impact. On the other hand, the use of salt hydrates or ester as PCM in the cubicles results in an impact reduction of 9% and 10.5% respectively, compared to the case of using paraffin., The work was partially funded by the Spanish government (projects ENE2008-06687-C02-01/CON and DPI2008-04099/DPI) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF −/− 253914)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Review on phase change materials (PCMs) for cold thermal energy storage applications

  • Oró Prim, Eduard
  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Thermal energy storage (TES) is a technology with a high potential for different thermal applications. It is well known that TES could be the most appropriate way and method to correct the gap between the demand and supply of energy and therefore it has become a very attractive technology. In this paper, a review of TES for cold storage applications using solid–liquid phase change materials has been carried out. The scope of the work was focussed on different aspects: phase change materials (PCMs), encapsulation, heat transfer enhancement, and the effect of storage on food quality. Materials used by researchers as potential PCM at low temperatures (less than 20 C) are summarized and some of their thermophysical properties are reported. Over 88 materials that can be used as PCM, and about 40 commercially available PCM have been listed. Problems in long term stability of the materials, such as corrosion, phase segregation, stability under extended cycling or subcooling are discussed. Heat transfer is considered both from theoretical and experimental point of view and the different methods of PCM encapsulation are reviewed. Many applications of PCM at low temperature can be found, such as, ice storage, conservation and transport of temperature sensitive materials and in air conditioning, cold stores, and refrigerated trucks., The work partially funded by the Spanish Government (ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS – FP7-PEOPLE-2009-IIF-/-253914). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534). Eduard Oró would like to thank the University of Lleida for his research fellowship.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Corrosion of metal and polymer containers for use in PCM cold storage

  • Oró Prim, Eduard
  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Transport and storage of low temperature sensitive products is an issue worldwide due to changes of the lifestyle and population increase. In the recent years, thermal energy storage (TES) using phase change materials (PCMs) is being highly studied and developed for cold storage applications. Furthermore, the PCM are normally encapsulated in containers and added in the available systems, usually in food processes. Therefore safety constraints as the compatibility of the PCM with other materials have to take into account. Hence the main goal of the paper is to study the corrosion effect of different metals and polymer materials in contact with some PCM used in low temperature applications. Results show that copper and carbon steel must be avoided as PCM containers, and aluminium is not recommended; stainless steel 316 is recommended when in contact with the tested PCM. Moreover, PP, PS, PET, and HDPE are not affected by a process of degradation and are also compatible with the PCM studied., The work is partially funded by the Spanish Government (ENE2008-06687-C02-01/CON and ENE2011-22722) and the European Union (EFFIBUILDINGS). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534). Eduard Oró would like to thank University of Lleida for his research fellowship.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Analysis of implementing phase change materials in open-air swimming pools

  • Zsembinszki, Gabriel
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Open-air swimming pools in Mediterranean climate regions are heated by direct solar radiation with no auxiliary heating systems. In order to extend the swimming season or improve comfort conditions, solar collectors or pool coverings may be used. In this paper, another approach was followed through the use of phase change materials (PCM). Two methods of introducing the PCM were considered: (1) encapsulated in the sidewalls and bottom of the pool, and (2) use the PCM in an external heat exchanger. Heat is stored when water temperature is sufficiently high, while it is released when water temperature drops below comfort levels. A numerical model was built and validated for predicting the evolution of the water temperature, by taking into account meteorological data at three different locations in north-east of Spain. The simulations showed that using phase change materials provided some improvement of water conditions, especially when used in an external heat exchanger., The work was partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS - FP7-PEOPLE-2009-IIF -/- 253914).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal analysis of including phase change material in a domestic hot water cylinder

  • Gracia Cuesta, Alvaro de
  • Oró Prim, Eduard
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
The domestic electrical hot water cylinder used in this paper incorporates encapsulated phase change material (PCM) placed in 57 vertical pipes. The use of PCM increases the thermal energy storage capacity of the cylinder and allows the use of low cost electricity during low peak periods. The operational mode of the system is based on heating the water and melting the phase change material during night. After first discharge of hot water, the phase change material will transfer heat to the recently introduced cold water and increase its temperature without using electricity. The already measured experimental data prove the efficiency of the use of PCM in these systems and are used to validate a developed code for numerical simulation using finite volume method. Following model validation a parametrical study was carried out to optimize the PCM distribution inside the hot water cylinder., The work partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS - FP7-PEOPLE-2009-IIF -/- 253914). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534)., MICINN/PN2008-2011/ENE2008-06687-C02-01/CON
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

New equipment for testing steady and transient thermal performance of multilayered building envelopes with PCM

  • Gracia Cuesta, Alvaro de
  • Barreneche Güerisoli, Camila
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Thermal properties of the different building envelopes, such as thermal transmittance in steady state, heat storage capacity and dynamic thermal responses, must be taken into account during the design phase of buildings. The evaluation and measurement of these parameters in multilayered samples are difficult because of the irregular morphology of the used materials and the difficulty in providing the well-controlled environment needed for the measurements. A new equipment has been designed to measure the thermal response and heat capacity of composite walls of different materials simulating real building envelopes. The equipment presented in this paper was used to test the improvement in the thermal response of a building envelope due to the incorporation of PCM. This study is focused on wood structural panels attached to a gypsum board, which is either impregnated or not with PCM. The four edges of the composite sample are properly insulated to ensure one-dimensional heat flow. The two faces of the sample are exposed to controlled environments heated and cooled by copper coils with thermo stated water supplied by water baths. The measured surface heat fluxes at both surfaces of the sample and temperature distribution in the sample provide accurate assessment to thermal mass and dynamic response of the composite wall, while the steady state measurements provide an accurate estimate of its effective thermal transmittance., The work partially funded by the Spanish government (ENE2008-06687-C02-01/CON) and the European Union (COST Action COST TU0802 and project EFFIBUILDINGS - FP7-PEOPLE-2009-IIF -/- 253914)