Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal conductivity measurements of high and low thermal conductivity films using a scanning hot probe method in the 3ω mode and novel calibration strategies

  • Wilson, Adam Andrew
  • Muñoz Rojo, Miguel
  • Abad Mayor, Begoña
  • Pérez Taborda, Jaime Andrés
  • Maiz, Jon
  • Schomacker, Jason
  • Martín-González, Marisol
  • Borca Tasciuc, Diana-Andra
  • Borca Tasciuc, Theodorian
This work discusses measurement of thermal conductivity (k) of films using a scanning hot probe method in the 3ω mode and investigates the calibration of thermal contact parameters, specifically the thermal contact resistance (RthC) and thermal exchange radius (b) using reference samples with different thermal conductivities. RthC and b were found to have constant values (with b = 2.8 ± 0.3 μm and Rthc = 44 927 ± 7820 K W−1) for samples with thermal conductivity values ranging from 0.36 W K−1 m−1 to 1.1 W K−1 m−1. An independent strategy for the calibration of contact parameters was developed and validated for samples in this range of thermal conductivity, using a reference sample with a previously measured Seebeck coefficient and thermal conductivity. The results were found to agree with the calibration performed using multiple samples of known thermal conductivity between 0.36 and 1.1 W K−1 m−1. However, for samples in the range between 16.2 W K−1 m−1 and 53.7 W K−1 m−1, calibration experiments showed the contact parameters to have considerably different values: Rthc = 40 191 ± 1532 K W−1 and b = 428 ± 24 nm. Finally, this work demonstrates that using these calibration procedures, measurements of both highly conductive and thermally insulating films on substrates can be performed, as the measured values obtained were within 1–20% (for low k) and 5–31% (for high k) of independent measurements and/or literature reports. Thermal conductivity results are presented for a SiGe film on a glass substrate, Te film on a glass substrate, polymer films (doped with Fe nano-particles and undoped) on a glass substrate, and Au film on a Si substrate. © 2015 The Royal Society of Chemistry., We gratefully acknowledge funding from the US Department of Energy, Office of Basic Energy Sciences through the S3TEC Energy Frontiers Research Center (T. B. T.) and NSF IRES grant #1028071 for financial support towards this work (A. A. W. and D. B. T.). We would also like to acknowledge support from ECR StG NanoTEC 240497, and PHOMENTA project MAT2011-27911 and NanoHiTEC project FP7-263306 (M. M. G.), and CSIC for a JAE Pre-Doctoral fellowship (M. M. R.)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High thermoelectric zT in n‐type silver Selenide films at room temperature

  • Pérez Taborda, Jaime Andrés
  • Caballero-Calero, Olga
  • Vera Londoño, Liliana Patricia
  • Briones Fernández-Pola, Fernando
  • Martín-González, Marisol
In this work, a zT value as high as 1.2 at room temperature for n‐type Ag2Se films is reported grown by pulsed hybrid reactive magnetron sputtering (PHRMS). PHRMS is a novel technique developed in the lab that allows to grow film of selenides with different compositions in a few minutes with great quality. The improved zT value reported for room temperature results from the combination of the high power factors, similar to the best values reported for bulk Ag2Se (2440 ± 192 µW m−1 K−2), along with a reduced thermoelectric conductivity as low as 0.64 ± 0.1 W m−1 K−1. The maximum power factor for these films is of 4655 ± 407 µW m−1 K−2 at 103 °C. This material shows promise to work for room temperature applications. Obtaining high zT or, in other words, high power factor and low thermal conductivity values close to room temperature for thin films is of high importance to develop a new generation of wearable devices based on thermoelectric heat recovery., This work has been supported by 7th framework European project Nanostructured High‐efficiency Thermo‐Electric Converters project NANOHITEC 263306, ERC Nano‐TEC project, and Intramural project INFANTE. J.A.P.T and O.C.C. acknowledge the Spanish Ministerio de Economía, Industria y Competitividad for their FPI grant and Ramón y Cajal Fellowship, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pulsed hybrid reactive magnetron sputtering for high zTCu2Se thermoelectric films

  • Pérez Taborda, Jaime Andrés
  • Vera Londoño, Liliana Patricia
  • Caballero-Calero, Olga
  • López, Elvis O.
  • Romero Fanego, Juan José
  • Stroppa, Daniel G.
  • Briones Fernández-Pola, Fernando
  • Martín-González, Marisol
Thermoelectric films on flexible substrates are of interest for the integration of thermoelectric in wearable devices. In this work, copper selenide films are achieved by a novel low‐temperature technique, namely pulsed hybrid reactive magnetron sputtering (PHRMS). A brief introduction to the basic chemistry and physics involved during growth is included to explain its fundamentals. PHRMS is a single‐step, room temperature (RT), fabrication process carried out in another ways conventional vacuum sputtering system. It does not require high‐temperature post‐annealing to obtain films with great thermoelectric performance. It is, therefore, compatible with polymeric substrates like Kapton tape. Several sets of films covering a large exploratory compositional range (from Cu/Se = 1 to 9) are deposited and their microstructure and thermoelectric properties are analyzed at RT. Power factors as high as 1.1 mW m−1 K−2 in the in‐plane direction and thermal conductivities as low as κ = 0.8 ± 0.1 W m−1 K−1 in the out‐of‐plane direction have been obtained for β‐Cu2Se films. Consequently, a figure of merit of 0.4 at RT can be estimated under the assumption that for this polycrystalline cubic phase no additional anisotropy in the thermoelectric properties is introduced by the planar configuration. Moreover, PHRMS is also industrially scalable and compatible with the in‐line fabrication of other selenides., This work was supported by 7th framework European project Nano‐structured High‐efficiency Thermo‐Electric Converters project NANOHITEC 263306, ERC Nano‐TEC project, the national project PHOMENTA MAT2011‐27911 and Intramural project INFANTE. J.A.P.‐T. acknowledges the Spanish Ministerio de Economia y Competitividad for their FPI grant. The authors wish to thank the National Synchrotron Light Source at the Brazilian Synchrotron (LNLS)—XRD2 beamline—in Campinas, Brazil, for the SR‐GIXRD measurements. The authors acknowledge the X‐SEM Laboratory at IMM (VERIOS 460 from FEI) and funding from MINECO under project CSIC 13‐4E‐1794 with support from EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low thermal conductivity and improved thermoelectric performance of nanocrystalline silicon germanium films by sputtering

  • Pérez Taborda, Jaime Andrés
  • Romero Fanego, Juan José
  • Abad Mayor, Begoña
  • Muñoz Rojo, Miguel
  • Mello, A.
  • Briones Fernández-Pola, Fernando
  • Martín-González, Marisol
SixGe1−x alloys are well-known thermoelectric materials with a high figure of merit at high temperatures. In this work, metal-induced crystallization (MIC) has been used to grow Si0.8Ge0.2 films that present improved thermoelectric performance (zT = 5.6 × 10−4 at room temperature) —according to previously reported values on films—with a relatively large power factor (σ · S2 = 16 μW · m−1 · K−2 ). More importantly, a reduction in the thermal conductivity at room temperature (κ = 1.13 ± 0.12 W · m−1 · K−1 ) compared to other Si–Ge films (∼3 W · m−1 · K−1 ) has been found. Whereas the usual crystallization of amorphous SiGe (a-SiGe) is achieved at high temperatures and for long times, which triggers dopant loss, MIC reduces the crystallization temperature and the heating time. The associated dopant loss is thus avoided, resulting in a nanostructuration of the film. Using this method, we obtained Si0.8Ge0.2 films (grown by DC plasma sputtering) with appropriate compositional and structural properties. Different thermal treatments were tested in situ (by heating the sample inside the deposition chamber) and ex situ (annealed in an external furnace with controlled conditions). From the studies of the films by: x-ray diffraction (XRD), synchrotron radiation grazing incidence x-ray diffraction (SR-GIXRD), micro Raman, scanning electron microscopy (SEM), x-ray photoemission spectroscopy (XPS), Hall effect, Seebeck coefficient, electrical and thermal conductivity measurements, we observed that the in situ films at 500 °C presented the best zT values with no gold contamination., This work has been supported by the 7th framework of the European project NANOHITEC 263306, the national project PHOMENTA MAT2011-27911, and Infante 201550E072. J A Pérez Taborda acknowledges the Spanish Ministerio de Economia y Competitividad for their FPI grant, and Banco Santander for their special grant for a short stay in Brazil (Brazilian Center of Physical Researches, Rio de Janeiro). Special thanks go to Marta Rull for her assistance in the treatment of the ex situ samples and I Fernández-Martínez of Nano4Energy for his assistance in the commissioning of the sputtering system. The authors wish to thank the Synchrotron Light Brazilian National Laboratory (LNLS)—XRD2 beam line—in Campinas, Brazil, for the XRD measurements (Dr Elvis Lopez and Dr R Ospina, Lab. of Surface and Nanostructures, Centro Brasileiro de Pesquisas Físicas-RJ, Brazil)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultra-low thermal conductivities in large-area Si-Ge nanomeshes for thermoelectric applications

  • Pérez Taborda, Jaime Andrés
  • Muñoz Rojo, Miguel
  • Maiz, Jon
  • Neophytou,Neophytos
  • Martín-González, Marisol
In this work, we measure the thermal and thermoelectric properties of large-area Si0.8Ge0.2 nano-meshed films fabricated by DC sputtering of Si0.8Ge0.2 on highly ordered porous alumina matrices. The Si0.8Ge0.2 film replicated the porous alumina structure resulting in nano-meshed films. Very good control of the nanomesh geometrical features (pore diameter, pitch, neck) was achieved through the alumina template, with pore diameters ranging from 294 ± 5nm down to 31 ± 4 nm. The method we developed is able to provide large areas of nano-meshes in a simple and reproducible way, being easily scalable for industrial applications. Most importantly, the thermal conductivity of the films was reduced as the diameter of the porous became smaller to values that varied from κ = 1.54 ± 0.27 W K−1m−1, down to the ultra-low κ = 0.55 ± 0.10 W K−1m−1 value. The latter is well below the amorphous limit, while the Seebeck coefficient and electrical conductivity of the material were retained. These properties, together with our large area fabrication approach, can provide an important route towards achieving high conversion efficiency, large area, and high scalable thermoelectric materials., This work has been supported by 7th framework European project NANOHITEC 263306, national project PHOMENTA MAT2011-27911, CONSOLIDER NANOTHERM Grant No. CSD2010-00044, and INFANTE. J.A. Pérez acknowledges Ministerio de Economia y Competitividad for his FPI grant and Banco Santander for a special grant for a short stay in Brazil (Brazilian Center of Physical Researches-Rio de Janeiro). M. M. R. wants to acknowledge JAE Pre-Doc grant for PhD financial support. NN acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No 678763). NN also acknowledges Dr. Hossein Karamitaheri for helpful discussions. MMG wants also to acknowledge the Salvador Madariaga Fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Ultra-low thermal conductivities in large-area Si0.8Ge0.2 nanomeshes grown by DC-Sputtering for thermoelectric applications

  • Pérez Taborda, Jaime Andrés
  • Muñoz Rojo, Miguel
  • Maiz, Jon
  • Neophytou,Neophytos
  • Martín-González, Marisol
Trabajo presentado en el Spring Meeting European Materials Research, celebrado Francia del 22 al 26 de mayo de 2017, In this work, we measure the structural, morphological, compositional, thermal and thermoelectric properties of large-area Si0.8Ge0.2 nanomeshed films manufactured by DC-sputtering of Si0.8Ge0.2 on highly ordered porous alumina matrices [1]. The Si0.8Ge0.2 film replicated the porous alumina structure resulting in nano-meshed films. Very good control of the nanomesh geometrical features (pore diameter, pitch, neck) was achieved through the alumina template, with pore diameters ranging from 294 ± 5nm down to 31 ± 4 nm. The method that we developed is able to provide large areas of nano-meshes in a simple and reproducible way, being easily scalable for industrial applications. Most importantly, the thermal conductivity of the films was reduced as the diameter of the porous became smaller to values that varied from ¿ = 1.54 ± 0.27 W K¿1m¿1, down to the ultra-low ¿ = 0.55 ± 0.10 W K¿1m¿1 value. The latter is well below the amorphous limit, while the Seebeck coefficient and electrical conductivity of the material were retained. These properties, together with our large area fabrication approach, can provide an important route towards achieving high conversion efficiency, large area, and high scalable thermoelectric materials. Using this approach, it is possible to control thermal transport of these films through nano-engineering., Project Nanostructured Highefficiency Thermo-Electric Converters project NANOHITEC 263306. PHOtoacoustic MEasurements of Nanostructures for Thermoelectric Applications (PHOMENTA). National Project Infante 201550E072, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Alta eficiencia termoeléctrica en películas delgadas nanoestructuradas de SIGe, Cu2Se y Ag2Se depositadas por pulverización catódica

  • Pérez Taborda, Jaime Andrés
Tesis llevada a cabo para conseguir el grado de Doctor por la Universidad Complutense de Madrid.--2017-09-28, [ES] Los materiales termoel´ectricos convierten energ´ıa t´ermica en energ´ıa el´ectrica y viceversa. Las ventajas de los materiales termoel´ectricos son que no poseen partes m´oviles, son dispositivos de larga duraci´on, son silenciosos, pueden utilizarse en aplicaciones para enfriar y calentar, y tambi´en pueden emplearse para la recuperaci´on de energ´ıa proveniente del calor residual. En los ´ultimos a˜nos se han propuesto diferentes alternativas prometedoras destinadas a conseguir sistemas con coeficientes zT superiores a 1. Un coeficiente zT de 1 supone una eficiencia de generaci´on de energ´ıa el´ectrica a partir de energ´ıa t´ermica de un 10 % del l´ımite te´orico, dado por el ciclo de Carnot, mientras que un valor de 4 supondr´ıa un 30 %. Para este prop´osito, esto es, estudiar c´omo aumentar la eficiencia termoel´ectrica en distintos materiales, en primer lugar se han obtenido pel´ıculas delgadas de Si0,8Ge0,2 a trav´es de un sistema de pulverizaci´on cat´odica de ultra alto vac´ıo construido para este fin. El primer objetivo ha sido lograr obtener pel´ıculas delgadas de Si0,8Ge0,2 policristalinas con bajos valores de conductividad t´ermica (cercanos a los reportados en la literatura para los nanohilo) y a bajas temperaturas de fabricaci´on. Adicionalmente, un segundo objetivo ha consistido en la fabricaci´on de nanomallas de Si0,8Ge0,2 con un control del tama˜no de poro y del espesor de la nanoestructura. Este nuevo enfoque en la fabricaci´on se realiza en un ´unico paso, sin necesidad de procesos litogr´aficos o tratamientos t´ermicos adicionales. El segundo n´ucleo de estudio en esta tesis doctoral ha estado alrededor de la fabricaci´on de pel´ıculas delgadas de seleniuros de cobre Cu2−xSe y plata Ag2−xSe. Estos materiales han exhibido recientemente prometedores valores de zT, as´ı como algunas propiedades particularmente curiosas, como una conducci´on el´ectrica similar a un l´ıquido i´onico a altas temperaturas. Dentro de esta tesis doctoral, un tercer objetivo ha sido el dise˜no y construcci´on de un sistema para la deposici´on de estos materiales en forma de pel´ıculas delgadas por procesos de sputtering reactivo. De esta forma somos capaces de obtener pel´ıculas con una composici´on bien definida mediante un adecuado control de los par´ametros de crecimiento. Esto nos permite de forma sencilla realizar estudios de la variaci´on de las propiedades con la composici´on del material. Adem´as, nuestro sistema nos permite modificar con gran celeridad los par´ametros de crecimiento, de tal manera que se pueden obtener multicapas que den lugar a procesos de dispersi´on de fonones, reduciendo as´ı la conductividad t´ermica del material (y mejorando por lo tanto el factor zT)., [EN] Thermoelectric materials are those that convert thermal energy into electrical energy and vice-versa. The advantages of thermoelectric devices are many, such as being solid state devices, that is, with no mobile parts and no noise, and they are durable, among others. They can be used in applications for heating and cooling, but more importantly, they can be used to recover wasted heat converting it into electrical energy. In the last years there have been different promising ways of obtaining thermoelectric systems with figures of merit zT higher than 1. A zT of 1 means to have an electric energy generation efficiency from thermal gradients of 10 % of the theoretical limit, which is given by the Carnot cycle, while a value of zT of 4 would mean a 30 % efficiency. In order to study one route of increasing the thermoelectric efficiency of different materials, thin films of Si0,8Ge0,2 have been fabricated with a sputtering system at ultrahigh vacuum, which was constructed specifically to this purpose. The first objective was to obtain polycrystalline thin films of Si0,8Ge0,2 fabricated at low temperatures and with reduced thermal conductivity (with values near the ones reported in literature for nanowires of the same material). Additionally, a second objective consisted in the fabrication of nano-meshes of Si0,8Ge0,2 with controlled pore size and thickness of the nano-structure. This new approach in the fabrication was performed in a single step, without any lithographical process or additional thermal treatments. The second nucleus of this PhD Thesis has been on the fabrication of thin films of copper selenides (Cu2−xSe) and silver selenides (Ag2−xSe). This materials have recently exhibited quite promising values of zT, as well as some quite particular properties, such as an electrical conductivity similar to that of an ionic liquid at high temperatures. In the frame of this PhD Thesis, the design and construction of a system for the deposit of such materials in the form of thin films via reactive sputtering has been also performed. With the aid of this reactive sputtering system we are able to obtain films with a well-defined and controlled composition due to an adequate regulation of the growth parameters. This allows us to perform studies on the different properties of the films as a function of the stoichiometry, for instance. Moreover, with our system one can modify the growth parameters rapidly, which provides a way to obtain multi-layers which provide a higher phonon dispersion and thus, a reduction of the thermal conductivity of the material (which produces a further increase the thermoelectric figure of merit,zT)., La realización de esta tesis doctoral ha sido posible gracias a la financiación del proyecto europeo NANOHITEC 263306, el proyecto nacional PHOMENTA MAT2011-27911, proyecto Intramural INFANTE y a la concesión de una ayuda FPI del Ministerio de Economía, Industria y Competitividad - Gobierno de España., Peer reviewed