Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 40
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nano-patterning of perpendicular magnetic recording media by low-energy implantation of chemically reactive ions

  • Martín-González, Marisol
  • Briones Fernández-Pola, Fernando
  • García-Martín, José Miguel
  • Montserrat Martí, Josep
  • Vila, L.
  • Faini, G.
  • Testa, A. M.
  • Fiorani, D.
  • Rohrmann, H.
Magnetic nanopatterning of perpendicular hard disc media with perpendicular anisotropy, but preserving disc surface planarity, is presented here. Reactive ion implantation is used to locally modify the chemical composition (hence the magnetization and magnetic anisotropy) of the Co/Pd multilayer in irradiated areas. The procedure involves low energy, chemically reactive ion irradiation through a resist mask. Among N, P and As ions, P are shown to be most adequate to obtain optimum bit density and topography flatness for industrial Co/Pd multilayer media. The effect of this ion contributes to isolate perpendicular bits by destroying both anisotropy and magnetic exchange in the irradiated areas. Low ion fluences are effective due to the stabilization of atomic displacements levels by the chemical effect of covalent impurities., The work was supported by the EC Growth project HIDEMAR (Contract No. G5RD-CT-2002-00731). MSMG want to thanks to the Ramon y Cajal program and ERC-Stg-2008: 240497., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fractional quantum conductance values in Au nanoelectrodes due to hydrogen adsorption

  • Díaz Muñoz, Marcos
  • Martín-González, Marisol
  • Costa Krämer, José Luis
Hydrogen adsorption in gold nanocontact electrodes in electrochemical solution is experimentally discerned. This is performed with gold nanocontact conductance histograms in an electrochemical environment in which both the electrochemical potential and the electrolyte type are varied. Different salts, acids, and hydrogen peroxide electrolytes are studied. Salts and acids exhibit at negative electrochemical potentials different fractional quantum conductance histograms peaks associated to extra stable structures due to H adsorption while these peaks do not appear for H2O2 where electron transfer between solution and electrodes occurs without hydrogen formation or hydrogen adsorption on the gold electrode., We thank A García-Martín and J. J. Saenz for helpful discussions. MD acknowledges Spanish Science Ministry, MEC, for financial support during a sabbatical year through its Researchers Exchange and Mobility Program. The authors express their thanks to the MICINN for projects MAT2008-06330 and PLE2009-0073, and to the European Commission ERC-2008-Stg:240497 for their financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modification of optical properties in ZnO particles by surface deposition and anchoring of NiO nanoparticles

  • Rubio Marcos, Fernando
  • Manzano, Cristina V.
  • Jiménez Reinosa, Julián
  • Lorite, Israel
  • Romero Fanego, Juan José
  • Fernández Lozano, José Francisco
  • Martín-González, Marisol
Nanodispersion of NiO nanoparticles on the surface of ZnO microparticles has been carried out by means of a low energy dry mixing method. This method keeps the shape and size of the ZnO microparticles that served as support to hold the NiO nanoparticles. The dispersion and anchoring of the NiO nanoparticles takes place by means of an electrochemical reaction with the OH-groups present at the ZnO surface. The process took place at room temperature and cation interdiffusion between ZnO and NiO have not been detected by structural analysis. Nevertheless, changes in the optical properties of semiconductor ZnO particles have been observed due to the deposition of the nanoparticles. These changes correlate with the amount of NiO nanoparticles at the ZnO particle surface. The amount of defects, i.e oxygen vacancies, interstitial oxygen and zinc vacancies, rises with the increasing NiO content., The authors express their thanks to the CICYT project MAT2010-21088-C03-01, MAT2008-06330, PLE2009-0073, and to the European Commission ERC-2008-Stg: 240497 for their financial support. MSMG want to acknowledge B. Alen from IMM for technical support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mechanism of Ni1–xZnxO Formation by Thermal Treatments on NiO Nanoparticles Dispersed over ZnO

  • Rubio Marcos, Fernando
  • Manzano, Cristina V.
  • Jiménez Reinosa, Julián
  • Romero Fanego, Juan José
  • Marchet, Pascal
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
9 figuras, The formation of Ni1–xZnxO rock salt solid solution is obtained by thermal treatments applied to NiO nanoparticles supported on ZnO micrometric particles. The high vapor pressure of ZnO produces a Zn-rich atmosphere during thermal treatment. The Zn ions tend to be adsorbed by the highly reactive NiO nanoparticles. When heated to temperatures high enough, over 500 °C, the Zn ions react with the NiO nanoparticles forming the rock salt material. By variation of the treatment temperature, the composition of this rock salt structure can be varied through the whole solubility range., The authors express their thanks to the MICINN (Spain)projects MAT 2010-21088-C03-01, MICINN ACI PLAN E (JAPON) ref: PLE2009-0073, and to the European Comission ERC-2008-Stg: 240497 for their financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and luminescence properties of electrodeposited ZnO films

  • Manzano, Cristina V.
  • Alegre Castro, Daniel
  • Caballero-Calero, Olga
  • Alén, Benito
  • Martín-González, Marisol
8 páginas, 10 figuras., Zinc oxide (ZnO) films have been grown on gold (111) by electrodeposition using two different OH− sources, nitrate and peroxide, in order to obtain a comparative study between them. The morphology, structural and optical characterization of the films were investigated depending on the solution used (nitrate and peroxide) and the applied potential. Scanning electron microscopy pictures show different morphologies in each case. X-ray diffraction confirms that the films are pure ZnO oriented along the (0002) direction. ZnO films have been studied by photoluminescence to identify the emission of defects in the visible range. A consistent model that explains the emissions for the different electrodeposited ZnO films is proposed. We have associated the green and yellow emissions to a transition from the donor OH− to the acceptor zinc vacancies (VZn−) and to interstitial oxygen (Oi0), respectively. The orange-red emission is probably due to transitions from the conducting band to Oi− and OZn0 defects and the infrared emission to transition from these Oi−/2− and OZn0/− defects to the valence band., The authors would like to acknowledge partial financial support from MICINN Project No. MAT2008-06330 and ERC StG NanoTEC 240497., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Depth dependent lattice disorder and strain in Mn-implanted and post-annealed InAs thin films

  • González-Arrabal, Raquel
  • Redondo-Cubero, A.
  • González Díez, Yolanda
  • González Sotos, Luisa
  • Martín-González, Marisol
The lattice order degree and the strain in as-grown, Mn-implanted and post-implantedannealedInAsthinfilms were investigated with depth resolution by means of Rutherford backscattering spectrometry in channeling conditions (RBS/C). Three main crystallographic axes were analyzed for both In and As sublattices. The behaviour of the induced defects was evaluated in two regions with different native defects: the interface and the surface. The results show that Mn implantation and post-implantation annealing are anisotropic processes, affecting in a different way the In and As sublattices. The mechanisms influencing the enhancement and deterioration of the crystal quality during the implantation are discussed in relation to the as-grown defects and the segregation of the elements., This work was supported by CSIC 2006-50F0122 and CSIC 2007-50I015. One of the authors ARC acknowledges financial support from by FCT in Portugal (BPD/74095/2010). MSMG acknowledges to ERC-2008-Stg: 240497 and to the MICINN ACI PLAN E (JAPON) PLE2009-0073 for their financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

In-depth study of self-ordered porous alumina in the 140-400 nm pore diameter range

  • Martín Pérez, Jaime
  • Manzano, Cristina V.
  • Martín-González, Marisol
The growth of self-ordered anodic aluminum oxide (AAO) templates with pore diameters in the 140-400 nm range is achieved by anodization in phosphoric acid at low temperatures (-4 °C). The procedure used in this study is able to completely avoid the >burning> of the oxide, highly frequent in anodizations in phosphoric acid solutions at high voltages. The current density measured during the anodizations is rather low, 0.6-0.7 mA/cm2; therefore, low growth rates have been also measured (<2 μm/h). AAO templates present a relatively low porosity value of 8.4%. However, a considerable pore-enlargement-rate (vΔd = 0.636 ± 0.101 nm/h) has been observed as a consequence of the chemical dissolution of the pore walls during the anodization. Thus, the results reported here constitute an exhaustive study on the preparation of large-diameter-pore self-ordered AAO templates that enables both to access to pore diameters up to now inaccessible and to efficiently overcome the difficulties of their fabrication process ascribed to its aggressive reaction conditions. © 2011 Elsevier Inc. All rights reserved., Authors want to thank the ERC 2008 Starting Grant number 240497 for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ordered arrays of polymeric nanopores by using inverse nanostructured PTFE surfaces

  • Martín Pérez, Jaime
  • Martín-González, Marisol
  • Campo, Ángel Adolfo del
  • Jiménez Reinosa, Julián
  • Fernández Lozano, José Francisco
We present a simple, efficient, and high-throughput methodology for the fabrication of ordered nanoporouses polymeric surfaces with areas in the range of cm2. The procedure is based on a two-stage replication of a master nanostructured pattern. The process starts with the preparation of an ordered array of PTFE (poly(tetrafluorethylene)), PTFE) free-standing nanopillars by wetting self-ordered porous Anodic Aluminum Oxide (AAO) templates with molten PTFE. The nanopillars are 120 nm in diameter and approximately 350 nm in length, while the array extends over cm2. The PTFE nanostructuration process induces a surface hydrocarbonation of the nanopillars, as revealed by confocal Raman microscopy/spectroscopy, which enhances the wettability of the originally hydrophobic material and facilitates its subsequent use as an inverse pattern. Thus, the PTFE nanostructure is then used as a negative master for the fabrication of macroscopic hexagonal arrays of nanopores composed of biocompatible poly(vinylalcohol) (PVA). In this particular case, the nanopores are 130-140 nm in diameter and the interpore distance is around 430 nm. Features of such characteristic dimensions are known to be well recognizable by the living cells. Moreover, the inverse mold is not destroyed in the pore array demoulding process and can be reused again for a new pore array fabrication. Therefore, the developed method allows the high throughput production of cm2-scale biocompatible nanopores surfaces that could be interesting as two-dimensional scaffolds for tissue repairing or wound healing. Moreover, our approach can be extrapolated to almost any polymer and biopolymer ordered pore array fabrication., The authors want to thank the ERC 2008 Starting Grant number 240497 and project MAT2010-21088-C03-01 for financial support. Dr Helmut Reinecke is acknowledged for his help with the ATR-FTIR measurements, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The use of PEEK nanorod arrays for the fabrication of nanoporous surfaces under high temperature: SiNx example

  • Martín Pérez, Jaime
  • Martín-González, Marisol
Large area silicon nitride (SiNx) nanoporous surfaces are fabricated using poly(ether-ether-ketone) (PEEK) nanorod arrays as a template. The procedure involves manipulation of nanoporous anodic aluminum oxide (AAO) templates in order to form an ordered array of PEEK nanopillars with high temperature resistant characteristics. In this context, self-ordered AAO templates are infiltrated with PEEK melts via the “precursor film” method. Once the melts have been crystallized in the porous structure of AAO, the basis alumina layer is removed, yielding an ordered array of PEEK nanopillars. The resulting structure is a high temperature and chemical resistant polymeric nanomold, which can be utilized in the synthesis of nanoporous materials under aggressive conditions. Such conditions are high temperatures (up to 320 °C), vacuum, or extreme pH. For example, SiNx nanopore arrays have been grown by plasma enhanced chemical vapor deposition at 300 °C, which can be of interest as mold for nanoimprint lithography, due to its hardness and low surface energy. The SiNx nanopore array portrays the same characteristics as the original AAO template: 120 nm diameter pores and an interpore distance of 430 nm. Furthermore, the aspect ratio of the SiNx nanopores can be tuned by selecting an AAO template with appropriate conditions. The use of PEEK as a nanotemplate extends the applicability of polymeric nanopatterns into a temperature regime up to now not accessible and opens up the simple fabrication of novel nanoporous inorganic surfaces., Authors want to thank the ERC 2008 Starting Grant “Nano-TEC” number 240497 for financial support. We acknowledge R. Alvaro for the SiNx deposition and Yazmin Feliz for the idiomatic corrections of the manuscript., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The smectic-isotropic transition of P3HT determines the formation of nanowires or nanotubes into porous templates

  • Martín Pérez, Jaime
  • Nogales, Aurora
  • Martín-González, Marisol
We present the simple and controllable fabrication of ordered arrays of poly(3-hexylthiophene) (P3HT) solid nanowires and hollow nanotubes by infiltrating the molten polymer into AAO nanopores at temperatures promoting partial (260 C) and complete (280 C) wetting regimes, respectively. We show that such wetting regimes (and thus the formation of nanowires or nanotubes) are associated with a different internal structure in the P3HT melt. At 260 C, the P3HT organizes into a smectic mesophase. Thus, the translational motion of the P3HT molecule through the phase-separated structure would involve an enthalpic penalty, which prevents the molecular diffusion required for achieving the complete wetting regime. Consequently, the P3HT wets the nanopores in partial wetting regime, so that solid nanowires are formed. In contrast, the melt is structurally isotropic at 280 C, which promotes the complete wetting regime, yielding nanotubes. Such a smectic mesophase is also present in P3HT confined into 350 nm in diameter pores. Furthermore, we observe the formation of a new type of nanostructure consisting of twinned nanotubes (two pores formed from one original pore) as a consequence of the appearance of a longitudinal meniscus which divided the hollow interior of the initial nanotube into two independent compartments. Lastly, we use the capillary rise of the P3HT melt along the cylindrical nanopores as a >coarse> nanoscale viscosimetry experiment for the measurement of its viscosity value under confinement. The physical behavior observed for P3HT might be extrapolated to other semiconducting polymers with similar comblike molecular architectures with applications in optoelectronics, thermoelectrics, and photovoltaics (like other poly(alkylthiophenes), polycarbazoles, polyfluorenes, polyphenylenes, etc.). © 2013 American Chemical Society., ERC 2008 Starting Grant “NanoTEC” number 240497. Spanish Ministry Economy and Competitiveness (Project MAT2008-03232 and MAT2011-23455)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication and Mechanical Characterization of Semi-Free-Standing (Conjugated) Polymer Thin Films

  • Martín Pérez, Jaime
  • Muñoz Rojo, Miguel
  • Encinar, Mario
  • Calleja, Montserrat
  • Martín-González, Marisol
Polymers undergo severe low-dimensionality effects when they are confined to ultrathin films since most of the structural and dynamical processes involving polymer molecules are correlated to length scales of the order of nanometers. However, the real influence of the size limitation over such processes is often hard to identify as it is masked by interfacial effects. We present the fabrication of a new type of nanostructure consisting of poly[[9-(1-octylnonyl)-9H-carbazole-2,7-diyl]-2,5-thiophenediyl-2,1,3-benzothiadiazole-4,7-diyl-2,5-thiophenediyl] (PCDTBT) thin film that is held up exclusively over tips of poly(ether–ether–ketone) (PEEK) nanopillars. The fabrication method exploits the nonwetting behavior of PCDTBT onto an ordered PEEK nanopillar array when the mobility of the PCDTBT molecules is enhanced by a solvent annealing process. We use this new configuration to characterize the mechanical behavior of free-standing thin film regions, thus in the absence of underlaying substrate, by means of an atomic force microscope (AFM) setup. First, we study how the finite thickness and/or the presence of the underlying substrate influences the mechanical modulus of the material in the linear elastic regime. Moreover, we analyze deep indentations up to the rupture of the thin film, which allow for the measurement of important mechanical features of the nanoconfined polymer, such as its yield strain, the rupture strain, the bending rigidity, etc., which are impossible to investigate in thin films deposited on substrates., This work was supported by the ERC Starting Grants “NanoTEC” (ERC-StG-2008-240497) and “NANOFORCELLS” (ERC-StG-2011-278860)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Review on measurement techniques of transport properties of nanowires

  • Muñoz Rojo, Miguel
  • Caballero-Calero, Olga
  • Lopeandia, A. F.
  • Rodriguez Viejo, Javier
  • Martín-González, Marisol
Physical properties at the nanoscale are novel and different from those in bulk materials. Over the last few decades, there has been an ever growing interest in the fabrication of nanowire structures for a wide variety of applications including energy generation purposes. Nevertheless, the study of their transport properties, such as thermal conductivity, electrical conductivity or Seebeck coefficient, remains an experimental challenge. For instance, in the particular case of nanostructured thermoelectrics, theoretical calculations have shown that nanowires offer a promising way of enhancing the hitherto low efficiency of these materials in the conversion of temperature differences into electricity. Therefore, within the thermoelectrical community there has been a great experimental effort in the measurement of these quantities in actual nanowires. The measurements of these properties at the nanoscale are also of interest in fields other than energy, such as electrical components for microchips, field effect transistors, sensors, and other low scale devices. For all these applications, knowing the transport properties is mandatory. This review deals with the latest techniques developed to perform the measurement of these transport properties in nanowires. A thorough overview of the most important and modern techniques used for the characterization of different kinds of nanowires will be shown. © 2013 The Royal Society of Chemistry., This work has been supported by ERC Starting Grant Nano-TEC number 240497, Nanotherm Consolider CSD-2010-00044 project and PHOMENTA project MAT2011-27911. MM and OC wish to acknowledge CSIC and the European Social Fund for financial support by JAE-Pre and JAE-Doc. JRV and AFL acknowledge financial support from Generalitat de Catalunya through Grant SGR2009-01225 and from Marie Curie European Reintegration Grant within the 7th European Community Framework Programme., We also acknowledge institutional support from the Unit of Information Resources for Research at the "Consejo Superior de Investigaciones Científicas" (CSIC) for the article-processing charges contribution., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication of Bi2Te3 nanowire arrays and thermal conductivity measurement by 3ω-scanning thermal microscopy

  • Muñoz Rojo, Miguel
  • Grauby, Stéphane
  • Rampnoux , J. M.
  • Caballero-Calero, Olga
  • Martín-González, Marisol
  • Dilhaire, Stefan
Bi2Te3 is well-known for its utility in thermoelectrical applications and more recently as topological insulator. Its nanostructuration has attracted plenty of attention because of its potential capacity to reduce thermal conductivity. Here, we have grown a composite sample made of a Bi2Te3 nanowires (NWs) array embedded in an alumina matrix. We have then performed scanning thermal microscopy (SThM) in a 3ω configuration to measure its equivalent thermal resistance. Using an effective medium model, we could then estimate the mean composite thermal conductivity as well as the thermal conductivity of the NWs to be, respectively, (λC) = (1.68 ± 0.20) W/mK and (λNW) = (1.37 ± 0.20) W/mK, showing a slight thermal conductivity reduction. Up to now, there have been two main techniques reported in literature to evaluate the thermal conductivity of nanostructures: the use of a thermal microchip to probe a single NW once its matrix has been dissolved or the probing of the whole NWs array embedded in a matrix, obtaining the thermal conductivity of the whole as an effective medium. However, the 3ω-SThM presented here is the only technique able to measure the thermal conductivity of single NWs embedded in a matrix as well as the thermal conductivity of the composite locally. This technique is more versatile and straightforward than other methods to obtain the thermal conductivity of nanostructures. © 2013 American Institute of Physics., This work has been supported by the ANR PNANO and by ERC Starting Grant Nano-TEC number 240497. M.M and O.C. wants to acknowledge CSIC and European Social Fund for financial support by JAE-Pre and JAE-Doc., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanoengineering thermoelectrics for the 21st century: Energy harvesting and other trends in the field

  • Martín-González, Marisol
  • Caballero-Calero, Olga
  • Díaz Chao, Pablo
In the beginning of the 21st century, the world is facing the major challenge of finding energy sources to satisfy the ever-increasing energy consumption while preserving the environment. In the race to search alternative energy sources, thermoelectric generators are called to play their role in the improvement of the efficiency of the actual energy system by harvesting nowadays wasted heat. This review deals with the novel aspects of nano-structuring of thermoelectric materials, from the so called 3D nanobulk materials down to the incorporation of 0D quantum dots in thermoelectric structures. The improvement in the efficiency of nanoengineering thermoelectrics benefits mainly from the reduction in the thermal conductivity. Other promising trends in thermoelectricity are also reviewed, such as, novel nano-structures, trending materials (polymers, thermionic materials or Zintl phases), spin caloritronics, thermoelectricity in atomic and molecular junctions, or recent developments in theoretical calculations. Finally the review ends with a brief review on recent thermoelectric devices., Authors want to thank the ERC 2008 Starting Grant Nano-TEC number 240497 for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Poly(3-hexylthiophene) nanowires in porous alumina: Internal structure under confinement

  • Martín-Benito, Jaime
  • Campoy Quiles, Mariano
  • Nogales, Aurora
  • Garriga, Miquel
  • Alonso Carmona, M. Isabel
  • Goñi, Alejandro R.
  • Martín-González, Marisol
We study the structure of poly(3-hexylthiophene) (P3HT) subjected to nanoscale confinement in two dimensions (2D) as imposed by the rigid walls of nanopore anodic aluminum oxide (AAO) templates. P3HT nanowires with aspect ratios (length-to-diameter) above 1000 and diameters ranging between 15 nm and 350 nm are produced in the pores of the AAO templates via two processing routes. These are, namely, drying a solution or cooling from the melt. Our study focuses on the effects of nanoconfinement on the semicrystalline nature of the nanowires, the orientation of crystals, and the evolution of the structures that P3HT might develop under confinement, which we investigate by combining imaging (SEM), spectroscopic (FTIR, photoluminescence) and structural characterization (WAXS, DSC) techniques. Solution-processed P3HT nanowires are essentially amorphous and porous, whereas melt-processed nanowires are semicrystalline, and present a more compact morphology and smoother surfaces. In the latter case, the orientation of crystals was found to strongly depend on the pore diameter. In large diameter nanowires (250 nm and 120 nm), crystals are oriented laying the π-π stacking direction parallel to the nanowire axis. In contrast, in small diameter nanowires, the π-π stacking direction is mainly perpendicular to the nanowires, as crystals are likely to nucleate at pore walls. The structural evolution of P3HT upon heating into weakly (250 nm in diameter) and strongly (15 nm in diameter) confining pores has been studied. A complex set of structures is observed, i.e., crystals, a solid layered mesophase, a nematic/smectic mesophase, and the isotropic melt. Interestingly, a rare crystal polymorph (form II) is also observed under strong confinement conditions together with the usual lamellar crystal form I. Furthermore, we show that nanoconfinement stabilizes form II: such crystals are still present at 210 °C while in the bulk they get converted to form I crystals at around 50 °C. © 2014 the Partner Organisations., This work was supported by the ERC-2009-St-G. “Nano-TEC” Grant agreement number: 240497 and Spanish Ministerio de Economía y Competitividad through the projects CSD2010- 00044 (Consolider NANOTHERM), PLE2009-0052, MAT2009- 10642, MAT2008-03232, MAT2011-23455, MAT2011-27911 and MAT2012-37776., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High electrical conductivity in out of plane direction of electrodeposited Bi2Te3 films

  • Muñoz Rojo, Miguel
  • Manzano, Cristina V.
  • Granados, Daniel
  • Osorio, M. R.
  • Borca Tasciuc, Theodorian
  • Martín-González, Marisol
© 2015 Author(s). The out of plane electrical conductivity of highly anisotropic Bi<inf>2</inf>Te<inf>3</inf> films grown via electro-deposition process was determined using four probe current-voltage measurements performed on 4.6 - 7.2 μm thickness Bi<inf>2</inf>Te<inf>3</inf> mesa structures with 80 - 120 μm diameters sandwiched between metallic film electrodes. A three-dimensional finite element model was used to predict the electric field distribution in the measured structures and take into account the non-uniform distribution of the current in the electrodes in the vicinity of the probes. The finite-element modeling shows that significant errors could arise in the measured film electrical conductivity if simpler one-dimensional models are employed. A high electrical conductivity of (3.2 ± 0.4) · 10<sup>5</sup> S/m is reported along the out of plane direction for Bi<inf>2</inf>Te<inf>3</inf> films highly oriented in the [1 1 0] direction., M.M.G. wants to acknowledge support from ERC StG NanoTEC 240497. M.M.R. acknowledges CSIC for his JAE Pre-Doctoral fellowship. T.B.T. gratefully acknowledges funding from the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences through the S3TEC Energy Frontiers Research Center at MIT under Award No. DE-SC0001299., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal conductivity measurements of high and low thermal conductivity films using a scanning hot probe method in the 3ω mode and novel calibration strategies

  • Wilson, Adam Andrew
  • Muñoz Rojo, Miguel
  • Abad Mayor, Begoña
  • Pérez Taborda, Jaime Andrés
  • Maiz, Jon
  • Schomacker, Jason
  • Martín-González, Marisol
  • Borca Tasciuc, Diana-Andra
  • Borca Tasciuc, Theodorian
This work discusses measurement of thermal conductivity (k) of films using a scanning hot probe method in the 3ω mode and investigates the calibration of thermal contact parameters, specifically the thermal contact resistance (RthC) and thermal exchange radius (b) using reference samples with different thermal conductivities. RthC and b were found to have constant values (with b = 2.8 ± 0.3 μm and Rthc = 44 927 ± 7820 K W−1) for samples with thermal conductivity values ranging from 0.36 W K−1 m−1 to 1.1 W K−1 m−1. An independent strategy for the calibration of contact parameters was developed and validated for samples in this range of thermal conductivity, using a reference sample with a previously measured Seebeck coefficient and thermal conductivity. The results were found to agree with the calibration performed using multiple samples of known thermal conductivity between 0.36 and 1.1 W K−1 m−1. However, for samples in the range between 16.2 W K−1 m−1 and 53.7 W K−1 m−1, calibration experiments showed the contact parameters to have considerably different values: Rthc = 40 191 ± 1532 K W−1 and b = 428 ± 24 nm. Finally, this work demonstrates that using these calibration procedures, measurements of both highly conductive and thermally insulating films on substrates can be performed, as the measured values obtained were within 1–20% (for low k) and 5–31% (for high k) of independent measurements and/or literature reports. Thermal conductivity results are presented for a SiGe film on a glass substrate, Te film on a glass substrate, polymer films (doped with Fe nano-particles and undoped) on a glass substrate, and Au film on a Si substrate. © 2015 The Royal Society of Chemistry., We gratefully acknowledge funding from the US Department of Energy, Office of Basic Energy Sciences through the S3TEC Energy Frontiers Research Center (T. B. T.) and NSF IRES grant #1028071 for financial support towards this work (A. A. W. and D. B. T.). We would also like to acknowledge support from ECR StG NanoTEC 240497, and PHOMENTA project MAT2011-27911 and NanoHiTEC project FP7-263306 (M. M. G.), and CSIC for a JAE Pre-Doctoral fellowship (M. M. R.)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermoelectric properties of electrodeposited tellurium films and the sodium lignosulfonate effect

  • Abad Mayor, Begoña
  • Rull Bravo, Marta
  • Hodson, Stephen L.
  • Xu, Xianfan
  • Martín-González, Marisol
© 2015 Elsevier Ltd. All rights reserved. The effect of the addition of a surfactant, sodium lignosulfonate (SLS), on the thermoelectric properties of tellurium films prepared by electrochemical deposition is studied. The growth mechanism is found to have an important role in the thermoelectric properties since the grain size of the films is sharply reduced when the surfactant is added to the solution. For this reason, the electrical resistivity of the tellurium films when the surfactant is not added is 229 μΩ·m, which is lower than 798 μΩ·m with SLS. The Seebeck coefficient values are not influenced, with values in the vicinity of 285 μV/K for both solutions. The power factor resulted higher values than previous works, reaching values of 280 μW/m·K<sup>2</sup> (without SLS) and 82 μW/m·K<sup>2</sup> (with SLS) at room temperature. Finally, the thermal conductivity was measured by means of the Photoacoustic technique, which showed values of the order of 1 W/m·K for both solutions, which is a factor of 3 less than the bulk value of tellurium. A notable observation is that the power factor and the thermal conductivity of electrodeposited tellurium films have the same order of magnitude of bismuth telluride films grown by electrodeposition. The figure of merit is estimated to be approximately one order of magnitude higher than the bulk value, 0.09 without SLS and 0.03 with SLS, both at room temperature., The authors would like to acknowledge the financial support from ERC StG NanoTEC240497 and national project PHOMENTA MAT2011-27911., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improvement of Bismuth Telluride electrodeposited films by the addition of Sodium Lignosulfonate

  • Caballero-Calero, Olga
  • Díaz Chao, Pablo
  • Abad Mayor, Begoña
  • Manzano, Cristina V.
  • Ynsa, M. D.
  • Romero Fanego, Juan José
  • Muñoz Rojo, Miguel
  • Martín-González, Marisol
In this work we report the improvement on the electrodeposition of Bi 2Te3 films with the c-axis parallel to the surface of the substrate. This has been done with the addition of a surfactant agent (sodium lignosulfonate) to the electrochemical bath. A thorough study of the electrodeposition parameters and the material composition, morphology, crystallographic orientation and transport properties was performed. High quality films oriented along the (1 1 0) plane and with a dense morphology were obtained, showing an improved Seebeck coefficient up to 33% bigger than previously reported values. The differences in the morphology due to the presence of the surfactant have been further analyzed studying the shape of films grown from discrete nucleation sites. © 2014 Elsevier Ltd., The authors would like to acknowledge financial support from a joint project with Japan NANOTHERMA (FCCI), ERC StG NanoTEC 240497, and the Consolider proyect Nanotherm CSD2010-00044. O.C.C. wants to acknowledge her JAE post-doctoral position and M.M.R. and C.V.M. their JAE pre-doctoral positions, from CSIC and the European Social Fund., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ordered three-dimensional interconnected nanoarchitectures in anodic porous ​alumina

  • Martín Pérez, Jaime
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
  • Caballero-Calero, Olga
Three-dimensional (3D) nanostructures combine properties of nanoscale materials with the advantages of being macro-sized pieces when the time comes to manipulate, measure their properties or make a device. However, the amount of compounds with the ability to self-organize in ordered 3D nanostructures is limited. Therefore, template-based fabrication strategies become the key approach towards 3D nanostructures. Here we report the simple fabrication of a template based on anodic ¿aluminium oxide, having a well-defined, ordered, tunable, homogeneous 3D nanotubular network in the sub 100-nm range. The 3D templates are then employed to achieve 3D, ordered nanowire networks in ¿Bi2Te3 and polystyrene. Finally, we demonstrate the photonic crystal behaviour of both the template and the polystyrene 3D nanostructure. Our approach may establish the foundations for future high-throughput, cheap, photonic materials and devices made of simple commodity plastics, metals and semiconductors., We would like to acknowledge financial support from ERC 2008 Starting Grant ‘Nano-TEC’ number 240497., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultra-narrow 12 nm pore diameter self-ordered anodic alumina templates

  • Manzano, Cristina V.
  • Martín Pérez, Jaime
  • Martín-González, Marisol
Ordered anodic aluminum oxide (AAO) templates with pores of 12 nm in diameter and aspect-ratios (length-to-diameter) of >1000 are prepared by a simple two-step anodization process under mild-anodization conditions. Such a low diameter pores are consequence of the reduction of the dielectric constant of the electrolyte together with the effect of increasing the electrolyte viscosity. We show that the temperature has a strong impact on reducing the pore diameter, as provokes the increase of viscosity of the medium and thus the hindering of the diffusion of species involved in the widening of pores. Moreover, we manage to stop the AAO growth process at the pore nucleation stage and we show that 8 nm in diameter pores are originally formed under these conditions. The presented ultra-narrow pore templates may allow for the preparation of ordered arrays of high aspect-ratio ultra-small one dimensional (1D) nanostructures that could be useful to explore quantum phenomena and integrate quantum-devices. © 2013 Elsevier Inc. All rights reserved., The authors would like to acknowledge financial support from ERC 2008 Starting Grant “Nano-TEC” number 240497. C.V.M. acknowledges CSIC and European Union Funding for JAE PhD fellowship., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrical contact resistances of thermoelectric thin films measured by Kelvin probe microscopy

  • Muñoz Rojo, Miguel
  • Caballero-Calero, Olga
  • Martín-González, Marisol
This work presents an approach for measuring cross plane electrical contact resistances directly using Kelvin Probe Microscopy. With this technique we were able to measure the electrical contact resistances of a cross section of a thermoelectric thin film made of Bi2Te3 sandwiched between two gold electrodes. On the one hand, the bottom gold electrode, which is located on top of the silicon substrate, was used as a cathode in electro-deposition process to grow the sample. On the other hand, the gold electrode on top was made via physical evaporation. The electrical contact resistances measured at both interfaces were 0.11 ± 0.01 Ω and 0.15 ± 0.01 Ω, respectively. These differences are related to differences between the top and bottom gold/bismuth-telluride film, obtaining smaller contact resistance where the film was grown by electro-deposition. © 2013 AIP Publishing LLC., This work has been supported by ERC Starting Grant Nano-TEC number 240497 and PHOMENTA project MAT2011-27911. M.M. and O.C. acknowledge CSIC for JAE-Pre and JAE-Doc, respectively., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-aspect-ratio and highly ordered 15-nm porous alumina templates

  • Martín Pérez, Jaime
  • Manzano, Cristina V.
  • Caballero-Calero, Olga
  • Martín-González, Marisol
Ordered anodic aluminum oxide (AAO) templates with pores <15 nm in diameter and an aspect ratio (length-to-diameter ratio) above 3 × 103 have been fabricated using a nonlithographic approach; specifically, by anodizing aluminum in an ethylene-glycol-containing sulfuric acid electrolyte. The pores are the smallest in diameter reported for a self-ordered AAO without pore aspect-ratio limitations and good ordering, which opens up the possibility of obtaining nanowire arrays in the quantum confinement regime that is of interest for efficient thermoelectric generators. The effect of the ethylene glycol addition on both the pore diameter and the ordering is evaluated and discussed. Moreover, 15-nm-diameter Bi2Te3 and poly(3-hexyl thiophene) (P3HT) nanowires have been prepared using these AAO templates. As known, Bi2Te3 is currently the most efficient thermoelectric bulk material for room-temperature operations and, according with theory, its Seebeck coefficient should be increased when it is confined to nanowires with diameters close to 10 nm. On the other hand, P3HT is one of the main candidates for integrating organic photovoltaic and thermoelectric devices, and its properties are also proposed to increase when it is confined to nanoscale structures, mainly due to molecular orientation effects., Authors want to thank the ERC 2008 Starting Grant “Nano-TEC” (No. 240497). C.V.M. and O.C.C. acknowledge CSIC and European Union Funding for a JAE Ph.D. grant and a JAE postdoctoral position, respectively., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improved power factor of polyaniline nanocomposites with exfoliated graphene nanoplatelets (GNPs)

  • Abad Mayor, Begoña
  • Alda, Irene
  • Díaz Chao, Pablo
  • Kawakami, Hiroshi
  • Almarza, Albert
  • Amantia, David
  • Gutiérrez, David
  • Aubouy, Laurent
  • Martín-González, Marisol
In this work, exfoliated graphene nanoplatelets (GNPs)/polyaniline (PANI) nanocomposites have been prepared by sequential processing comprising: (i) a first aniline oxidative polymerization step under acidic conditions and (ii) mechanical blending with GNPs at different percentages. Thermoelectric pellets of the hybrid materials have been obtained at suitable circular geometry by means of cold pressing. Thermoelectric parameters have been determined at room temperature (electrical conductivity, Seebeck coefficient and thermal conductivity). Thermoelectric measurements show a drastic enhancement in both electrical conductivity and Seebeck coefficient with the addition of GNPs. A respectable maximum power factor value of 14 μW m-1 K-2 is reached for hybrid materials charged at 50 wt% GNP content, evidencing a 1000-fold enhancement with respect to the raw PANI polymer. The measured thermal conductivity is in the range of 0.5 W m-1 K-1 for pure PANI to 3.3 W m-1 K-1 for 50 wt% GNP content, which matches the parallel thermal resistor model for this nanocomposite. © 2013 The Royal Society of Chemistry., This work has been supported by the ERC Starting Grant Nano-TEC number 240497, Consolider NANO-THERM, and the bilateral Spanish–Japanese NANOTHERMA projects are also acknowledged. I.A. acknowledges the Young Researcher award 2011 from the Spanish Ministry of Education for participation in this research at CSIC., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermoelectric composites of poly(3-hexylthiophene) and carbon nanotubes with a large power factor

  • Bounioux, Celine
  • Díaz Chao, Pablo
  • Campoy Quiles, Mariano
  • Martín-González, Marisol
  • Goñi, Alejandro R.
  • Yerushalmi-Rozene, Rachel
  • Müller, Christian
Composite films of poly(3-hexylthiophene) and single- as well as multi-walled carbon nanotubes are demonstrated to offer a competitive thermoelectric performance. The power factor significantly exceeds values obtained with either constituent alone provided that the conjugated polymer is sufficiently p-doped. The use of single-walled carbon nanotubes consistently results in a higher electrical conductivity with a maximum value above 10 3 S cm-1 and thus gives rise to a power factor of 25 ± 6 μW m-1 K-2 for a filler content of only 8 wt% and a maximum 95 ± 12 μW m-1 K-2 for 42-81 wt%. Moreover, a carbon nanotube content of 8-10 wt% does not compromise the low bulk thermal conductivity of the polymer matrix, which promises a high figure of merit of at least ZT > 10-2 at room-temperature. All samples are cast on plastic substrates, emphasising their suitability for large-area, flexible thermoelectric applications. © 2013 The Royal Society of Chemistry., This work was supported by the Ministerio de Economía y Competitividad through Grant CSD2010-00044 (Consolider NANOTHERM). C.M. gratefully acknowledges financial support from the CSIC through the JAE-Doc program (European Social Fund). M.C.-Q. thanks the Ministerio de Economía y Competitividad for funding through a Ramón y Cajal fellowship. M.S.M.-G. acknowledges the ERC for funding through an ERC 2008 Starting Grant “Nano-TEC” number 240497., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermoelectric properties of Bi2Te3 films by constant and pulsed electrodeposition

  • Manzano, Cristina V.
  • Rojas, Adriana A.
  • Decepida, Michelle
  • Abad Mayor, Begoña
  • Feliz, Yazmin
  • Caballero-Calero, Olga
  • Borca Tasciuc, Diana-Andra
  • Martín-González, Marisol
Bi2Te3 films have been grown by constant and pulsed electrochemical deposition. The pulsed deposition was carried out by alternating between a constant potential (potentiostatic mode) and an open circuit potential (galvanostatic mode, where current density is fixed at 0 mA/cm 2). The Harris texture analysis was performed to determine the degree of preferred orientation. The results showed that the films were strongly oriented along (1 1 0) direction. The morphology and compositions of the films were then analyzed. Finally, their Seebeck coefficient and electrical resistivity were measured and used to determine the thermoelectric Power Factor of the films for a temperature range between 57 and 107 C. © 2013 Springer-Verlag Berlin Heidelberg., The authors would like to acknowledge partial financial support from ERC StG NanoTEC 240497. D.A.B.T. acknowledges support from NSF IRES-1028071. C.V.M acknowledges a JAE Ph.D. grant, O.C.C. acknowledges JAE post-doctoral positions from CSIC, and the European Social Fund and B.A.M. recognizes the NANOTHERMA project (FCCI), MICINN project MAT2008-06330., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Thermoelectric properties of tellurium thick films prepared by electrodeposition

  • Abad Mayor, Begoña
  • Rull Bravo, Marta
  • Koh, Yee Rui
  • Hodson, Stephen L.
  • Xu, Xianfan
  • Shakouri, Ali
  • Sands, Timothy
  • Martín-González, Marisol
Póster presentado en la 12th European Conference on Thermoelectricity (ECT2014), celebrada en Madrid del 24 al 26 de septiembre de 2014., Tellurium is a p-type semiconductor with a narrow bandgap (0.34eV) and highly anisotropic crystal structure. It consists of helical chains which are bounded by covalent unions between the atoms and bound with other chains by Van der Waals interactions. These chains turn into a hexagonal lattice whose c axis is perpendicular to the hexagonal base or parallel to the helical chains., RC StG NANO-TEC EU 240497. PHOtoacoustic MEasurements of Nanostructures for Thermoelectric Applications (PHOMENTA)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Rules to determine thermal conductivity and density of Anodic Aluminum Oxide (AAO) membranes

  • Abad Mayor, Begoña
  • Maiz, Jon
  • Martín-González, Marisol
Extracting the thermal conductivity of single nanowires is greatly important in investigating the phonon scattering phenomena that can occur due to the reduction of the dimensions of the material. In order to extract the thermal conductivity of a single nanowire from a measurement of the whole nanowire array, the effective medium theory (EMT) is employed. To appropriately use EMT, the template thermal conductivity must be known. However, the values reported in literature vary greatly. In this work, the photoacoustic technique was used to determine thermal conductivity of different anodic aluminum oxide (AAO) membranes as a function of the pore diameter and type of electrolyte used. To accurately obtain the thermal conductivity, values for the porosity, skeletal density and specific heat of each AAO membrane were measured. These values are critically needed in the most mathematical models to obtain the thermal conductivity of nanowires/AAO composites and theoretical works. Values of 1.07 W m–1 K–1 for the skeletal AAO prepared in sulfuric acid and 1.32 W m–1 K–1 in oxalic and phosphoric acid membranes are obtained. Also, general equations to determine the thermal conductivity and density by determining its percentage of porosity are obtained., The authors would like to acknowledge the financial support from ERC StG NanoTEC 240497 and national project PHOMENTA MAT2011-27911., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal conductivity of Bi2Te3 nanowires: how size affects phonon scattering

  • Muñoz Rojo, Miguel
  • Abad Mayor, Begoña
  • Manzano, Cristina V.
  • Torres, P.
  • Cartoixà, Xavier
  • Álvarez, F. Xavier
  • Martín-González, Marisol
This work provides an in-depth study of how the thermal conductivity of stoichiometric [110] Bi2Te3 nanowires becomes affected when reducing its diameter from an experimental and theoretical point of view. The thermal conductivity was observed to decrease more than 70% (from 1.78 ± 0.46 W K−1 m−1 to 0.52 ± 0.35 W K−1 m−1) when the diameter of the nanowire was reduced one order of magnitude (from 300 nm to 25 nm). The Kinetic–Collective model was used to understand such a reduction, which can be explained by the impact that surface scattering has in acoustic phonons. The smaller the diameter of the nanowires is, the larger the alteration in the mean free path of the low-frequency phonons is. The model agrees well with the experimental data, and the reduction in the thermal conductivity of the nanowires can be explained in terms of an increment of phonon scattering., This work has been supported by the ERC Starting Grant Nano-TEC number 240497 and the national project PHOMENTA MAT2011-27911, and CONSOLIDER NANOTHERM No. CSD2010-0044. M. M. R. wants to acknowledge the National Research Council of Spain (CSIC) and the European Social Fund for PhD financial support by a JAE-Pre Doc fellowship. The authors acknowledge the Scanning Electron Microscope from the Institute of Microelectronics of Madrid (IMM-CSIC) 13-4E-1794. We acknowledge financial support by the Ministerio Español de Economía y Competitividad under Project No. TEC2015-67462-C2-2-R (MINECO/FEDER) and TEC2015-67462-C2-1-R (MINECO/FEDER). This project has also received funding from the Department d'Universitats, Recerca i Societat de la Informació of the Generalitat de Catalunya under contract 2014-SGR-384., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The fingerprint of Te-rich and stoichiometric Bi2Te3 nanowires by Raman spectroscopy

  • Rodríguez-Fernández, Carlos
  • Manzano, Cristina V.
  • Romero, Aldo H.
  • Martín Pérez, Jaime
  • Martín-González, Marisol
  • Morais, Mauricio
  • Cantarero, Andrés
We unambiguously show that the signature of Te-rich bismuth telluride is the appearance of three new peaks in the Raman spectra of Bi2Te3, located at 88, 117 and 137 cm−1 . For this purpose, we have grown stoichiometric Bi2Te3 nanowires as well as Te-rich nanowires. The absence of these peaks in stoichiometric nanowires, even in those with the smallest diameter, shows that they are not related to confinement effects or the lack of inversion symmetry, as stated in the literature, but to the existence of Te clusters. These Te clusters have been found in nonstoichiometric samples by high resolution electron microscopy, while they are absent in stoichiometric samples. The Raman spectra of the latter corresponds to the one for bulk Bi2Te3. The intensity of these Raman peaks are clearly correlated to the Te content. In order to ensure statistically meaningful results, we have investigated several regions from every sample, We thank the Ministry of Finances and Competitiveness for its financial support through the grants CSD2010–0044 of the Programme Consolider Ingenio, MAT2012–33843, and MAT2011–27911 as well as the FPI programme for young researchers. We also thank the University of Valencia for the use of the supercomputer Tirant. Financial support from the European Research Council through ERC 2008 Starting Grant number 240497 is also gratefully acknowledged. Finally, we would like to thank Dr. Said Agouram for his help with the HRTEM measurements., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Temperature-dependent thermal and thermoelectric properties of n -type and p -type S c 1 − x M g x N

  • Saha, Bivas
  • Pérez Taborda, Jaime Andrés
  • Bahk, Je-Hyeong
  • Koh, Yee Rui
  • Shakouri, Ali
  • Martín-González, Marisol
  • Sands, Timothy
Scandium Nitride (ScN) is an emerging rocksalt semiconductor with octahedral coordination and an indirect bandgap. ScN has attracted significant attention in recent years for its potential thermoelectric applications, as a component material in epitaxial metal/semiconductor superlattices, and as a substrate for defect-free GaN growth. Sputter-deposited ScN thin films are highly degenerate n-type semiconductors and exhibit a large thermoelectric power factor of∼3.5 × 10−3 W/m-K2 at 600–800 K. Since practical thermoelectric devices require both n- and p-type materials with high thermoelectric figures-of-merit, development and demonstration of highly efficient p-type ScN is extremely important. Recently, the authors have demonstrated p-type Sc1−xMgxN thin film alloys with low MgxNy mole-fractions within the ScN matrix. In this article, we demonstrate temperature dependent thermal and thermoelectric transport properties, including large thermoelectric power factors in both n- and p-type Sc1−xMgxN thin film alloys at high temperatures (up to 850 K). Employing a combination of temperature-dependent Seebeck coefficient, electrical conductivity, and thermal conductivity measurements, as well as detailed Boltzmann transport-based modeling analyses of the transport properties, we demonstrate that p-type Sc1−xMgxN thin film alloys exhibit a maximum thermoelectric power factor of ∼0.8 × 10−3 W/m-K2 at 850 K. The thermoelectric properties are tunable by adjusting the MgxNy mole-fraction inside the ScN matrix, thereby shifting the Fermi energy in the alloy films from inside the conduction band in case of undoped n-type ScN to inside the valence band in highly hole-doped p-type Sc1−xMgxN thin film alloys. The thermal conductivities of both the n- and p-type films were found to be undesirably large for thermoelectric applications. Thus, future work should address strategies to reduce the thermal conductivity of Sc1−xMgxN thin-film alloys, without affecting the power factor for improved thermoelectric performance, B.S. and T.D.S. acknowledge financial support by the National Science Foundation and U.S. Department of Energy (Grant No. CBET-1048616). M.M.G. acknowledges financial support from ERC Starting Grant NanoTEC 240497, and the INFANTE Project 201550E072. J.A.P.T. acknowledges the FPI from the project PHOMENTA (Grant No. MAT2011- 27911)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Non-contact methods for thermal properties measurement

  • Abad Mayor, Begoña
  • Borca Tasciuc, Diana-Andra
  • Martín-González, Marisol
Many of the renewable and sustainable energy technologies employ novel nanomaterials. For instance, thermal storage and thermoelectric conversion are in constant progress due to the emergence of new structures such as carbon-based materials, bulk nanostructures, 2D novel materials or nanowires. Thermal properties play a significant role to all these energy technologies as key parameters to evaluate the performance and efficiency of those materials in the final device. Understanding the effects of nanostructuring on thermal properties becomes critical, since a reduction in the thermal conductivity due to increased phonon scattering at interfaces is usually expected. Therefore, the determination of the thermal properties remains a critical aspect of material development effort, and measurement techniques are continuously developed or improved. Among those, non-contact heating methods are of importance since they bypass a frequent source of errors characteristic to contact-based thermal measurements, namely the thermal contact resistances, which can be dominant in nanoscale materials. Non-contact heating techniques are usually based on photothermal phenomenon, where heating is generated typically by incident radiation. This paper reviews non-contact heating measurement methods, providing an overview of basic principles for measurement along with associated theoretical model necessary for data reduction and their main applications. The techniques are categorized as time domain and frequency domain techniques, where the thermal response of the sample under study is analyzed as a function of time and frequency, respectively. Both types of methods study the transient response of the sample from a pulsed or modulated heating, and typical measurement output is thermal diffusivity. In addition, other non-contact techniques are also discussed, such as those based on steady-state response, from which the thermal conductivity is directly obtained, or those using AFM probe in the non-contact mode. Finally, main advantages and disadvantages of these techniques are summarized along with their associated uncertainties., The authors would like to acknowledge the financial support from ERC StG NanoTEC 240497. Authors also acknowledge CSIC through the Intramural INFANTE and MICINN through the CONSOLIDER-INGENIO 2010program (grant number CSD2010-00044) projects. D.A.B.-T. acknowledges Fulbright fellowship. M.S.M.-G. would like to thank her Salvador Madariaga fellowship from MECD., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Anisotropic effects on the thermoelectric properties of highly oriented electrodeposited Bi2Te3 films

  • Manzano, Cristina V.
  • Abad Mayor, Begoña
  • Muñoz Rojo, Miguel
  • Koh, Yee Rui
  • Hodson, Stephen L.
  • López-Martínez, Antonio
  • Xu, Xianfan
  • Shakouri, Ali
  • Sands, Timothy
  • Borca Tasciuc, Theodorian
  • Martín-González, Marisol
Highly oriented [1 1 0] Bi2Te3 films were obtained by pulsed electrodeposition. The structure, composition, and morphology of these films were characterized. The thermoelectric figure of merit (zT), both parallel and perpendicular to the substrate surface, were determined by measuring the Seebeck coefficient, electrical conductivity, and thermal conductivity in each direction. At 300 K, the in-plane and out-of-plane figure of merits of these Bi2Te3 films were (5.6 ± 1.2)·10−2 and (10.4 ± 2.6)·10−2, respectively., The authors would like to acknowledge partial financial support from ERC StG NanoTEC 240497, National Project No. MAT2011-27911, CONSOLIDER nanotherm, and Intramural Infante 201550E072. M.M.R acknowledges JAE PhD grant from CSIC and the European Social Fund. T.B.T. gratefully acknowledge funding from the US Departament of Energy, Office of Basic Energy Science through the S3TEC Energy Frontiers Research Center., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tailoring thermal conductivity via three-dimensional porous alumina

  • Abad Mayor, Begoña
  • Maiz, Jon
  • Ruiz-Clavijo, Alejandra
  • Caballero-Calero, Olga
  • Martín-González, Marisol
Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m−1·K−1, which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties., The authors would like to acknowledge the financial support from ERC StG NanoTEC 240497 and ERC POC TONALITy., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermoelectric nanowires: A brief prospective

  • Caballero-Calero, Olga
  • Martín-González, Marisol
Nanowire structures have been investigated in order to achieve improved thermoelectric performance of thermoelectric materials. This brief viewpoint article summarizes the progress done in the last years and our vision of which are the key points to achieve a future generation of efficient nanowire-based thermoelectric devices., The authors would like to recognize financial support from the ERC-StG NanoTEC 240497, ERC PoC 665634, Consolider Nanotherm CSD2010-00044, and MAT2011-27911., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Medidas de transporte térmico de materiales termoeléctricos mediante la técnica fotoacústica: del material en volumen a la nanoescala, Thermal transport measurements of thermoelectric materials by the photoacoustic technique: from bulk to nano

  • Abad Mayor, Begoña
Tesis llevada a cabo para conseguir el grado de Doctor por la Universidad Complutense de Madrid.--2016-02-19.--Sobresaliente Cum Laude, [ES] El objetivo de este trabajo de doctorado consistió en la implementación de la técnica fotoacústica, una herramienta muy poderosa para determinar la difusividad térmica de los materiales. Esta tesis puede dividirse en dos secciones principales: i) el diseño del montaje, implementación y calibración, y ii) medidas de las propiedades térmicas de diferentes tipos de materiales con aplicaciones en la termoelectricidad. La mayor motivación para implementar esta técnica se basa en la importancia de las propiedades térmicas en una amplia variedad de aplicaciones desde gestión térmica en electrónica, industria espacial o medicina, hasta conversión de energía mediante el efecto termoeléctrico. La termoelectricidad consiste en la habilidad de los materiales de convertir diferencias de temperaturas en electricidad y viceversa, de modo que el calor residual podría ser recuperado y reutilizado. La eficiencia de estos materiales está directamente relacionada con la conductividad eléctrica y el coeficiente Seebeck, e inversamente relacionada con la conductividad térmica. La caracterización de la conductividad térmica es por tanto crítica para evaluar a un material como un candidato prometedor en la termoelectricidad. Además, ha sido comprobado cómo la eficiencia termoeléctrica mejora por la reducción de la conductividad térmica debida a la dispersión de fonones por el efecto del tamaño nanométrico. Por consiguiente, la determinación de las propiedades térmicas de estos materiales nanoestructurados es crucial. Para este propósito se han desarrollado métodos de calentamiento de no contacto, los cuales permiten evitar las resistencias térmicas de contacto, uno de los grandes inconvenientes de muchas de las técnicas de medida de propiedades térmicas. Las técnicas de calentamiento en modo no-contacto se basan normalmente en el fenómeno fototérmico, donde el calor es generado por una radiación incidente. En el caso de la técnica fotoacústica, una radiación incidente modulada incide en la muestra por lo que la superficie se calienta y enfría y por tanto, el aire en contacto se expande y contrae como consecuencia de este calentamiento periódico. Debido a este efecto, se crean ondas acústicas que son detectadas mediante un micrófono. La señal proveniente del micrófono se compara con la señal del láser incidente y a partir del desfase entre ambas se pueden obtener las propiedades térmicas del material mediante un modelo teórico apropiado..., [EN] The aim of this PhD work was the implementation of the photoacoustic technique, a powerful tool to determine the thermal diffusivity of materials. This thesis can be divided in two fundamental sections: i) the set-up design, implementation, and calibration; and ii) thermal property measurements of different material types with applications in thermoelectricity. The main motivation to implement this technique lays on the importance of the thermal properties in a wide variety of applications from thermal management in electronics, space industry, or medicine; to energy conversion by means of the thermoelectric effects. The thermoelectricity is the ability of the materials to convert temperature differences into electricity and vice versa, so that any waste heat could be recovered and utilized. The efficiency of these materials is directly related to the electrical conductivity and the Seebeck coefficient and inversely related to the thermal conductivity. The thermal conductivity characterization is then critical to evaluate a material as a promising thermoelectric candidate. Moreover, the thermoelectric efficiency has been proved to be enhanced by the reduction of thermal conductivity through the increasing of phonon scattering due to nanosize effects. Therefore, the determination of the thermal properties of these nanostructures materials becomes crucial. For that purpose, non-contact heating methods are being developed, which allows for the thermal contact resistances to be avoided, which is one of the main drawbacks of many thermal property measurement techniques. Non-contact heating techniques are usually based on photothermal phenomenon, where heating is generated by an incident radiation. In the case of the photoacoustic technique, an incident modulated radiation impinges on the sample so that its surface is heating and cooling and hence, the air in contact with it expands and contracts as a consequence of this periodically heating. From this effect, acoustic waves are created and detected by a microphone. The signal coming from the microphone is then compared with the laser incident signal and from the phase shift the thermal properties of the material can be extracted with a proper theoretical model..., La realización de esta tesis doctoral ha sido posible gracias a la financiación del proyecto europeo ERC StG NanoTEC 240497 y el proyecto nacional PHOMENTA MAT2011‐27911., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pulsed current-voltage electrodeposition of stoichiometric Bi2Te3 nanowires and their crystallographic characterization by transmission electron backscatter diffraction

  • Manzano, Cristina V.
  • Polyakov, Mikhail N.
  • Maiz, Jon
  • Aguirre, Myriam H.
  • Maeder, Xavier
  • Martín-González, Marisol
Bi2Te3 nanowires with diameters ranging from 25 to 270 nm, ultra-high aspect ratio, and uniform growth front were fabricated by electrodeposition, pulsing between zero current density during the off time and constant potential during the on time (pulsed-current-voltage method, p-IV). The use of zero current density during the off time is to ensure no electrodeposition is carried out and the system is totally relaxed. By this procedure, stoichiometric nanowires oriented perpendicular to the c-axis is obtained for the different diameters of porous alumina templates. In addition, the samples show a uniform growth front with ultra-high aspect ratio single crystal nanowires. The high degree of crystallinity was verified by transmission electron backscatter diffraction. This characterization revealed that the nanowires present both large single crystalline areas and areas with alternating twin configurations., The authors would like to acknowledge partial financial support from ERC StG NanoTEC 240497, National Project No. MAT2017-86450-C4-3-R, and Intramural Infante CSIC 201550E072. M. H. A wants to acknowledge the financial support of European Commission through H2020 MSCARISE 2016, Project "SPICOLOST" No 734187 which are funding the access to LMA-INA equipment of Transmission Electron Microscopy., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improvements on Electrodeposited Bi2Te3-ySey Films by Different Additives

  • Caballero-Calero, Olga
  • Mohner, Melissa
  • Casas, Marina
  • Abad Mayor, Begoña
  • Rull Bravo, Marta
  • Borca Tasciuc, Diana-Andra
  • Martín-González, Marisol
Bismuth tellurium selenide (Bi2Te3-ySey) films have been electrochemically grownin a conventional three electrode cell. The addition of different components to the bath, namely Sodium Lignosulfonate (SLS) and Ethylendiaminetetraacetic Acid (EDTA) and their influence in morphology, stoichiometry, structure and Seebeck coefficientwas studied in order to improve the thermoelectric performance of Bi2Te3-ySey films. Films grown with SLS presented high crystallographic orientation and improved morphology, while those grown in the presence of EDTA had higher concentration of bismuth. The combination of both additives gave rise to stoichiometric Bi2Te2.7Se0.3films with denser morphology, higher orientation and higher Seebeck coefficients (60% larger) when compare with films grown without additives., The authors would like to thank financial support from the NanoTHERM consolider project (CSD 2010 00044), project IRES/DDEP 1208071 US National Science foundation program, and ERC Starting Grant Nano-TEC EU 240497 and the Lab. Microscopía Electrónica de Barrido of the Servicio Interdepartamental de Investigación (UAM-SIdI) for their availability to work with SEM and EDX., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Anisotropic effects on the thermoelectric properties of highly oriented electrodeposited Bi2Te3 films

  • Manzano, Cristina V.
  • Abad, Begoña
  • Muñoz, Miguel
  • Koh, Yee Rui
  • Hodson, Stephen L.
  • López Martínez, Antonio Miguel|||0000-0001-7232-0415
  • Shakouri, Ali
  • Sands, Timothy D.
  • Borca-Tasciuc, Theodorian
  • Martin, Marisol
Thermoelectric materials have garnered significant attention in response to the necessity to develop alternative energy sources than those that rely on fossil fuels. The performance of thermoelectric materials1 is quantified by their figure of merit, which is determined by the Seebeck coefficient (S), electrical conductivity (s), and thermal conductivity (¿). The figure of merit is formulated as, Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Anisotropic effects on the thermoelectric properties of highly oriented electrodeposited Bi2Te3 films

  • Manzano, Cristina V.
  • Abad, Begoña
  • Muñoz, Miguel
  • Koh, Yee Rui
  • Hodson, Stephen L.
  • López Martínez, Antonio Miguel
  • Shakouri, Ali
  • Sands, Timothy D.
  • Borca-Tasciuc, Theodorian
  • Martin, Marisol
Thermoelectric materials have garnered significant attention in response to the necessity to develop alternative energy sources than those that rely on fossil fuels. The performance of thermoelectric materials1 is quantified by their figure of merit, which is determined by the Seebeck coefficient (S), electrical conductivity (s), and thermal conductivity (¿). The figure of merit is formulated as, Peer Reviewed, Postprint (published version)