Pasar al contenido principal

TERMOELECTRICOS NANOESTRUCTURADOS DE ALTA FIGURA DE MERITO SINTERIZADOS EN FRIO.

MAT2017-86450-C4-3-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 21
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación

Three-Dimensional Bi2Te3 Networks of Interconnected Nanowires: Synthesis and Optimization

  • Ruiz-Clavijo, Alejandra
  • Caballero-Calero, Olga
  • Martín-González, Marisol
Self-standing Bi<sub>2</sub>Te<sub>3</sub> networks of interconnected nanowires were fabricated in three-dimensional porous anodic alumina templates (3D–AAO) with a porous structure spreading in all three spatial dimensions. Pulsed electrodeposition parameters were optimized to grow highly oriented Bi<sub>2</sub>Te<sub>3</sub> interconnected nanowires with stoichiometric composition inside those 3D–AAO templates. The nanowire networks were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), and Raman spectroscopy. The results are compared to those obtained in films and 1D nanowires grown under similar conditions. The crystalline structure and composition of the 3D Bi–Te nanowire network are finely tuned by controlling the applied voltage and the relaxation time off at zero current density during the deposition. With this fabrication method, and controlling the electrodeposition parameters, stoichiometric Bi<sub>2</sub>Te<sub>3</sub> networks of interconnected nanowires have been obtained, with a preferential orientation along [1 1 0], which makes them optimal candidates for out-of-plane thermoelectric applications. Moreover, the templates in which they are grown can be dissolved and the network of interconnected nanowires is self-standing without affecting its composition and orientation properties., Olga Caballero-Calero and Alejandra Ruiz-Clavijo acknowledge the funding of the Spanish Ministerio de Economía y Competitividad under the Ramón y Cajal program. The authors acknowledge the financial support of the Intramural Infante, MAT2017-86450-C4-3-R and the ERC Starting grant Nano-TEC projects. The authors acknowledge the service from the X-SEM Laboratory at IMN, and funding from MINECO under project CSIC13-4E-1794 with support from EU (FEDER, FSE), as well as the SIdI service at UAM for the EDX measurements.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Beyond Mono-, Di-, and Trisulfides: Synthesizing vanadium tetrasulfide (VS4) films for energy conversion

  • Flores, Eduardo
  • Muñoz-Cortés, Esmeralda
  • Bodega, Julio
  • Caballero-Calero, Olga
  • Martín-González, Marisol
  • Sánchez, Carlos
  • Ares, José R.
  • Ferrer, Isabel J.
Vanadium tetrasulfide (VS4, called patronite as a mineral) is a one-dimensional compound with promising properties for energy conversion applications. However, it has been scarcely investigated because of its complex synthesis. In this work, we report a detailed investigation about the formation mechanism of VS4 (V4+(S22–)2) as well as its structural, transport, and photoelectrochemical properties. To this aim, VS4 films were grown by a solid–gas reaction process between vanadium films and sulfur at temperatures between 350 and 450 °C during different reaction times. Film characterization (X-ray diffraction, energy-dispersive analysis of X-ray, micro-Raman spectroscopy, and scanning electron microscopy) reveals the formation of monoclinic VS4 nanorods (I2/C) as single crystalline phase in very short reaction times (t < 5 h). Optical characterization was carried out by reflectance and transmittance measurements to obtain the optical absorption coefficient (α = 104 cm–1 at photon energies higher than 1.6 eV). From these measurements, a direct optical band gap of 1.35 ± 0.05 eV is obtained. Additionally, VS4 films were used as photoanodes of a photoelectrochemical cell (PEC) with a platinum foil as counter electrode and a Ag/AgCl reference electrode to characterize the VS4/electrolyte (aqueous 0.5 M Na2SO3) interface. Finally, the evolved hydrogen under 200 mW/cm2 white light illumination over the VS4/interface at 0.3 V (Ag/AgCl) bias potential was quantified by a quadrupole mass spectrometer (QMS) reaching fluxes of ∼20 μmol/h., The authors are thankful for the technical support from Mr. F. Moreno. E.F. acknowledges the Mexican National Council for Science and Technology (CONACyT) for providing the funding necessary to complete his Ph.D. Authors from the MIRE Group acknowledge financial support by MINECO-FEDER (MAT2015-65203R). M.M.-G. and O.C.-C. acknowledge financial support by INFANTE (PIE 201550E072) and MINECO-FEDER (MAT2017-86450-C4-3-R) projects., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improvement of Seebeck coefficient in as-grown Bi2Te3-ySey electrodeposited films by the addition of additives and bath optimization

  • Caballero-Calero, Olga
  • Borca Tasciuc, Diana-Andra
  • Martínez-Moro, Rut
  • Gorog, András
  • Mohner, Melissa
  • Borca Tasciuc, Theodorian
  • Martín-González, Marisol
Bi2.0Te2.7Se0.3 is the most widely used thermoelectric n-type leg for large-scale cooling applications. However, as-grown electrodeposited Bi2Te3-ySey films typically have a Seebeck coefficient around a third of the bulk value, which sometimes can be improved with thermal annealings. In this work, we report as-grown Bi2Te3-ySey films having a Seebeck coefficient of approximately half the value of bulk without additional thermal treatments. All samples reported were deposited in baths containing no additives, sodium lignosulfonate (SLS), or both SLS plus ethylenediaminetetraacetic acid (EDTA) with a concentration of 1 M HNO3 (pH of 0 ± 0.1) and 0.6 M HNO3 (pH of 0.3 ± 0.1). For each scenario, the deposition was carried out at two different temperatures (0 °C and 5 °C). Seebeck values of −120 μV K−1 have been measured for as-grown films with an optimum morphology and stoichiometry (Bi2Te2.7Se0.3), which is ∼50% of the value obtained for this composition in bulk and the highest among as-grown electrochemically deposited films reported to date. These results are an incentive to revisit and further explore the chemistry behind the electrodeposition of bismuth telluride selenide films to improve the performance of electrodeposited thermoelectric films., M.M-G. acknowledges NSF IRES 1028071 support. D.-A. B.-T. acknowledge Fulbright fellowship support. M.M.G acknowledges the INFANTE, MAT2017-86450-C4-3-R and the ERC Starting grant NANO-Tec projects. O.C.C. wants to thank the financial support of Ramon y Cajal grant of the Spanish Government. The authors acknowledge the service from the X-SEM Laboratory at IMN, and funding from MINECO under project CSIC13-4E-1794 with support from EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanowires: A route to efficient thermoelectric devices

  • Domínguez-Adame, Francisco
  • Martín-González, Marisol
  • Sánchez, David
  • Cantarero, Andrés
Miniaturization of electronic devices aims at manufacturing ever smaller products, from mesoscopic to nanoscopic sizes. This trend is challenging because the increased levels of dissipated power demands a better understanding of heat transport in small volumes. A significant amount of the consumed energy in electronics is transformed into heat and dissipated to the environment. Thermoelectric materials offer the possibility to harness dissipated energy and make devices less energy-demanding. Heat-to-electricity conversion requires materials with a strongly suppressed thermal conductivity but still high electronic conduction. Nanowires can meet nicely these two requirements because enhanced phonon scattering at the surface and defects reduces the lattice thermal conductivity while electric conductivity is not deteriorated, leading to an overall remarkable thermoelectric efficiency. Therefore, nanowires are regarded as a promising route to achieving valuable thermoelectric materials at the nanoscale. In this paper, we present an overview of key experimental and theoretical results concerning the thermoelectric properties of nanowires. The focus of this review is put on the physical mechanisms by which the efficiency of nanowires can be improved. Phonon scattering at surfaces and interfaces, enhancement of the power factor by quantum effects and topological protection of electron states to prevent the degradation of electrical conductivity in nanowires are thoroughly discussed., This work was supported by the Spanish MICINN under grants MAT2015-63955-R, MAT2016-75955, MAT2016-82015-REDT, MAT2017-82639 and MAT2017-86450-C4-3-R., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pulsed current-voltage electrodeposition of stoichiometric Bi2Te3 nanowires and their crystallographic characterization by transmission electron backscatter diffraction

  • Manzano, Cristina V.
  • Polyakov, Mikhail N.
  • Maiz, Jon
  • Aguirre, Myriam H.
  • Maeder, Xavier
  • Martín-González, Marisol
Bi2Te3 nanowires with diameters ranging from 25 to 270 nm, ultra-high aspect ratio, and uniform growth front were fabricated by electrodeposition, pulsing between zero current density during the off time and constant potential during the on time (pulsed-current-voltage method, p-IV). The use of zero current density during the off time is to ensure no electrodeposition is carried out and the system is totally relaxed. By this procedure, stoichiometric nanowires oriented perpendicular to the c-axis is obtained for the different diameters of porous alumina templates. In addition, the samples show a uniform growth front with ultra-high aspect ratio single crystal nanowires. The high degree of crystallinity was verified by transmission electron backscatter diffraction. This characterization revealed that the nanowires present both large single crystalline areas and areas with alternating twin configurations., The authors would like to acknowledge partial financial support from ERC StG NanoTEC 240497, National Project No. MAT2017-86450-C4-3-R, and Intramural Infante CSIC 201550E072. M. H. A wants to acknowledge the financial support of European Commission through H2020 MSCARISE 2016, Project "SPICOLOST" No 734187 which are funding the access to LMA-INA equipment of Transmission Electron Microscopy., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly Efficient Antimicrobial Ceramics Based on Electrically Charged Interfaces

  • Jiménez Reinosa, Julián
  • Muñoz Rojo, Miguel
  • Campo, Ángel Adolfo del
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
The increasing threat of multidrug-resistant microorganisms is a cause of worldwide concern. This motivates a necessity to discover new antimicrobial agents or new mechanisms for microorganism eradication, different from those currently used. Here, we report an effective antibacterial ceramic glaze that combines different bactericidal mechanisms. Specifically, the used methodology of the glaze results in glass-free edge crystallizations of feldspar structures at the ceramic surface. A combination of Rutherford backscattering spectroscopy, scanning electron microscopy, and Raman microscopy is used to determine the chemical elements and crystallizations at the ceramic surface. Moreover, Kelvin probe force microscopy demonstrates that the presence of glass-free edges in feldspar needle crystals (semiconductor phase) on a glass matrix (insulator phase) promotes the formation of semiconductor-insulator interface barriers. These barriers act as reservoirs of electric charges of ∼1.5 V, producing a discharge exceeding the microorganism membrane breakdown value (up to 0.5 V). Furthermore, the surface crystallizations account for the formation of a microroughness that limits biofilm formation. Both factors result in high antibacterial activity in the range of R > 4 for Escherichia coli and Staphylococcus aureus. This approach opens new possibilities to attain bactericidal surfaces and to understand the role of physical interaction as a main antimicrobial mechanism., The authors acknowledege the financial support by the projects MAT2017-86450-C4-1-R and MAT2017-86450-C4-3-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sub-10 nm porous alumina templates to produce sub-10 nm nanowires

  • Resende, Pedro M.
  • Martín-González, Marisol
The versatility of Anodic Aluminum Oxide has led to the development of a variety of templates with ranging sizes, periodic modulations, and network-like architectures. These templates allow for the nanostructuration and study of new meta-materials, with interesting and important properties enhanced through size-reduction effects. In this work, we further extend the utility of these templates through the use of current anodization in concentrated Sulfuric acid and 25% V/V of ethanol under low current density values, obtaining small pore architectures with sub-10 nm features. In addition, polymer infiltration was performed as a proof of concept application, resulting in 8 nm nanowires. The templates reduced sizes allow for their application in the search for stable, extremely small diameter nanowires, and also for their use as scaffolds or filters., M.M.G. acknowledges the financial support from the projects INFANTE 201550E072 and MAT2017-86450-c4-3-r. The authors acknowledge the service from the X‐SEM Laboratory at IMN, and funding from MINECO under project CSIC13‐4E‐1794 with support from EU (FEDER, FSE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tailoring magnetic anisotropy at will in 3D interconnected nanowire networks

  • Ruiz-Clavijo, Alejandra
  • Ruiz-Gómez, Sandra
  • Caballero-Calero, Olga
  • Pérez, Lucas
  • Martín-González, Marisol
The authors acknowledge financial support from INFANTE 201550E072, MAT2017‐86450‐C4‐3‐R, and MAT2017‐87072‐C4‐2‐P. The authors also acknowledge the service from the X‐SEM Laboratory at IMM, and funding from MINECO under project CSIC13‐4E‐1794 with support from EU (FEDER, FSE) and project MAT2017‐87072‐C4‐2‐P.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Advances in scanning thermal microscopy measurements for thin films

  • Vera Londoño, Liliana Patricia
  • Caballero-Calero, Olga
  • Pérez Taborda, Jaime Andrés
  • Martín-González, Marisol
One of the main challenges nowadays concerning nanostructured materials is the understanding of the heat transfer mechanisms, which are of the utmost relevance for many specific applications. There are different methods to characterize thermal conductivity at the nanoscale and in films, but in most cases, metrology, good resolution, fast time acquisition, and sample preparation are the issues. In this chapter, we will discuss one of the most fascinating techniques used for thermal characterization, the scanning thermal microscopy (SThM), which can provide simultaneously topographic and thermal information of the samples under study with nanometer resolution and with virtually no sample preparation needed. This method is based on using a nanothermometer, which can also be used as heater element, integrated into an atomic force microscope (AFM) cantilever. The chapter will start with a historical introduction of the technique, followed by the different kinds of probes and operation modes that can be used. Then, some of the equations and heating models used to extract the thermal conductivity from these measurements will be briefly discussed. Finally, different examples of actual measurements performed on films will be shown. Most of these results deal with thermoelectric thin films, where the thermal conductivity characterization is one of the most important parameters to optimize their performance for real applications., The authors acknowledge the financial support of the Intramural INFANTE, and MAT2017- 86450-C4-3-R, as well as the service from the MiNa Laboratory at IMN, and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and EU (FEDER, FSE). O.C.C. acknowledges the funding of the Ramón y Cajal program (MINECO).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unravelling nanoporous anodic iron oxide formation

  • Martín-González, Marisol
  • Martínez-Moro, Rut
  • Aguirre, Myriam H.
  • Flores, Eduardo
  • Caballero-Calero, Olga
We studied the formation of self-ordered nanopores in the anodization of iron foils. Different anodization conditions (e.g. water content and applied voltage) were tested, and anodization curves were obtained for each case to establish the optimal parameters for fabricating homogeneous nanoporous films. Samples were characterized by Raman spectroscopy, X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, and high-resolution scanning transmission electron microscopy. Moreover, the bandgap of 2.1 ± 0.1 eV was measured in nanostructured films, and electrochemical impedance spectroscopy measurements were taken at each step. Finally, we propose a mechanism for the formation of iron oxide by anodization that takes into account the chemical reactions involved., The authors acknowledge the financial support of the Intramural Infante and MAT2017-86450-C4-3-R projects. The authors acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794) and EU (FEDER,FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crystal defects and optical emissions of pulse electrodeposited ZnO

  • Manzano, Cristina V.
  • Serrano Rubio, Aída
  • Muñoz-Noval, Alvaro
  • Fernández Lozano, José Francisco
  • Martín-González, Marisol
ZnO has been widely studied in the last decades as an n-type semiconductor due to its wide application range, for example, in optoelectronics, solar cells, light-emitting diodes, thermoelectrics, amongst others. The material efficiency for certain applications is highly dependent on the presenting film morphology. Electrodeposition is well-known as a technique with precise control over the structural and morphological properties of the obtained materials. When the structural and morphological properties are tuned, it is possible to find a wide variety of defects in the ZnO structure. In this study, ZnO films were grown using pulsed electrodeposition with variation of the reduction potential. The crystal order, structural defects and optical emissions of the films have been analyzed by X-Ray Diffraction (XRD), X-ray Absorption Near-Edge Structure (XANES), Extended X-ray Absorption Fine Structure (EXAFS) and Photoluminescence (PL). ZnO film grown at less negative reduction potential presents a stronger texture along [0001] by XRD, higher crystalline order, and more zinc vacancies by XANES and EXAFS. The films obtained at less negative potential present less OH trapped in the ZnO structure and a relatively higher level of defects O, O, O and O than those grown at higher reduction potentials by PL. This will be related to the fact that at less negative potentials there is less concentration of OH at the film surface than at more negative potentials. The combination of X-ray absorption spectroscopy and photoluminescence reveals the complicated nature of the atomic defect in electrodeposited ZnO films. Allowing to evidence the preferential presence of atomic defect as a function of the reduction potential. In this work, we have also compared those defects with reference compounds such as a Zn foil and ZnO polycrystalline powder., The authors would like to acknowledge financial support from MAT2017-86450-C4-1-R, MAT2017-86450-C4-3-R, and RTI2018-095303-A-C52. C.V.M acknowledges financial support from Juan de la Cierva Incorporación grants IJCI-2017-31350. A.S. and A.M.N. acknowledge the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract No. 2017-t2/IND5395 and 2018-T1/IND-10360, respectively. We acknowledge The European Synchrotron (ESRF), MICIU, and CSIC for provision of synchrotron radiation facilities in using the BM25-SpLine beamline. We also thank the BM25-SpLine staff for the technical support beyond their duties. We acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794) and EU (FEDER, FSE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrochemical deposition and thermoelectric characterisation of a semiconducting 2-D metal-organic framework thin film

  • González-Juárez, María de Lourdes
  • Flores, Eduardo
  • Martín-González, Marisol
  • Nandhakumar, Iris
  • Bradshaw, Darren
The electrical conductivity and porosity of the 2-dimensional metal-organic framework Cu3(2,3,6,7,10,11-hexahydroxytriphenylene)2 [Cu3(HHTP)2] make it a promising candidate for thermoelectric applications. In this work, we report the electrochemical synthesis of Cu3(HHTP)2 films by an anodization approach and an evaluation of its thermoelectric properties. The electrochemically synthesised Cu3(HHTP)2 thin films were transferred using a wet chemical method in order to perform electrical measurements. We are reporting the first thermoelectric measurements of this framework both in bulk and thin film form which resulted in Seebeck coefficients of -7.24 μV K-1 and -121.4 μV K-1 with a power factor of 3.15 × 10-3 μW m-1 for the film respectively. The negative Seebeck coefficients suggest that Cu3(HHTP)2 behaves as an n-type semiconductor. Since the introduction of conductive MOFs in electronic devices is at an early stage of development, we believe this work validates the use of electrochemical synthetic routes of conducting MOFs to further investigate and expand their applications in thin film technologies., M. Gonzalez-Juarez is supported by the National Council of Science and Technology-Mexico (CONACYT) under registry number 526108. MSMG acknowledges the project MAT2017- 86450-C4-3-R and EF the financial support from the project 201950E057.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High mobility and high thermoelectric power factor in epitaxial ScN thin films deposited with plasma-assisted molecular beam epitaxy

  • Rao, Dheemahi
  • Biswas, Bidesh
  • Flores, Eduardo
  • Chatterjee, Abhijit
  • Garbrecht, Magnus
  • Koh, Yee Rui
  • Bhatia, Vijay
  • Pillai, Ashalatha Indiradevi Kamalasanan
  • Hopkins, Patrick E.
  • Martín-González, Marisol
  • Saha, Bivas
Scandium nitride (ScN) is an emerging rock salt III-nitride semiconductor and has attracted significant interest in recent years for its potential thermoelectric applications as a substrate for high-quality epitaxial GaN growth and as a semiconducting component for epitaxial single-crystalline metal/semiconductor superlattices for thermionic energy conversion. Solid-solution alloys of ScN with traditional III-nitrides such as AlScN have demonstrated piezoelectric and ferroelectric properties and are actively researched for device applications. While most of these exciting developments in ScN research have employed films deposited using low-vacuum methods such as magnetron sputtering and physical and chemical vapor depositions for thermoelectric applications and Schottky barrier-based thermionic energy conversion, it is necessary and important to avoid impurities, tune the carrier concentrations, and achieve high-mobility in epitaxial films. Here, we report the high-mobility and high-thermoelectric power factor in epitaxial ScN thin films deposited on MgO substrates by plasma-assisted molecular beam epitaxy. Microstructural characterization shows epitaxial 002 oriented ScN film growth on MgO (001) substrates. Electrical measurements demonstrated a high room-temperature mobility of 127 cm/V s and temperature-dependent mobility in the temperature range of 50-400 K that is dominated by dislocation and grain boundary scattering. High mobility in ScN films leads to large Seebeck coefficients (-175 μV/K at 950 K) and, along with a moderately high electrical conductivity, a large thermoelectric power factor (2.3 × 10 W/m-K at 500 K) was achieved, which makes ScN a promising candidate for thermoelectric applications. The thermal conductivity of the films, however, was found to be a bit large, which resulted in a maximum figure-of-merit of 0.17 at 500 K., D.R., B.B., and B.S. acknowledge the International Center for Materials Science (ICMS) and Sheik Saqr Laboratory (SSL) in JNCASR for support. B.S. acknowledges the Science and Engineering Research Board (SERB) of the Government of India, Start-Up Research Grant No. SRG/2019/000613 for financial support. M.S.M.G. wants to acknowledge financial support from No. MAT2017-86450- C4-3-R and intramural CSIC Project No. 2D-MESES. M.G., V.B., and A.I.K.P acknowledge the facilities of Sydney Microscopy and Microanalysis at the University of Sydney. Y.R.K. and P.E.H. appreciate support from a MURI program through the Office of Naval Research, Grant No. N00014-18-1-2429.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The effects of microstructure, Nb content and secondary Ruddlesden-Popper phase on thermoelectric properties in perovskite CaMn1-: XNbxO3 (x = 0-0.10) thin films

  • Ekström, Erik
  • Le Febvrier, Arnaud
  • Bourgeois, F.
  • Lundqvist, B.
  • Palisaitis, J.
  • Persson, Per
  • Caballero-Calero, Olga
  • Martín-González, Marisol
  • Klarbring, J.
  • Simak, S.I.
  • Eriksson, F.
  • Paul, Biplab
  • Eklund, Per
CaMnNbO (x = 0, 0.5, 0.6, 0.7 and 0.10) thin films have been grown by a two-step sputtering/annealing method. First, rock-salt-structured (Ca,Mn,Nb)O thin films were deposited on 1100 sapphire using reactive RF magnetron co-sputtering from elemental targets of Ca, Mn and Nb. The CaMnNbO films were then obtained by thermally induced phase transformation from rock-salt-structured (Ca,MnNb)O to orthorhombic during post-deposition annealing at 700 °C for 3 h in oxygen flow. The X-ray diffraction patterns of pure CaMnO showed mixed orientation, while Nb-containing films were epitaxially grown in [101] out of-plane-direction. Scanning transmission electron microscopy showed a Ruddlesden-Popper (R-P) secondary phase in the films, which results in reduction of the electrical and thermal conductivity of CaMnNbO. The electrical resistivity and Seebeck coefficient of the pure CaMnO film were measured to 2.7 Ω cm and -270 μV K at room temperature, respectively. The electrical resistivity and Seebeck coefficient were reduced by alloying with Nb and was measured to 0.09 Ω cm and -145 μV K for x = 0.05. Yielding a power factor of 21.5 μW K m near room temperature, nearly eight times higher than for pure CaMnO (2.8 μW K m). The power factors for alloyed samples are low compared to other studies on phase-pure material. This is due to high electrical resistivity originating from the secondary R-P phase. The thermal conductivity of the CaMnNbO films is low for all samples and is the lowest for x = 0.07 and 0.10, determined to 1.6 W m K. The low thermal conductivity is attributed to grain boundary scattering and the secondary R-P phase., The authors acknowledge the funding from the Swedish Foundation for Strategic Research (SSF) through the Future Research Leaders 5 program, the Swedish Research Council (VR) under Project No. 2016-03365 and 2014-4750, the Knut and Alice Wallenberg Foundation through the Wallenberg Academy Fellows program and through support of the Electron Microscopy Laboratory at Linköping University, the Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linköping University (Faculty Grant SFO-Mat-LiU No. 2009 00971), the Swedish Energy Agency under project 46519-1, and the Spanish Ministry through the project MAT2017-86450-C4-3-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High thermoelectric efficiency in electrodeposited silver selenide films: from Pourbaix diagram to a flexible thermoelectric module

  • Manzano, Cristina V.
  • Caballero-Calero, Olga
  • Martín-González, Marisol
In the last few years, the exploration of new thermoelectric materials with low-toxicity, earth-abundance, and high-efficiency has become essential. Following this trend, sustainable, easily scalable, and costeffective fabrication methods, such as electrochemical deposition, are also desirable. In this work, the Pourbaix diagram of silver¿selenium¿water was developed to find an adequate pH and reduction potential for the electrodeposition of stable silver selenide. Based on this diagram, a solution without the incorporation of additives was developed. Silver selenide films were electrodeposited at different reduction potentials, and after the deposition, the compositional, morphological, and structural characterizations of the silver selenide thin films were analyzed. The thermoelectric properties of the electrodeposited silver selenide films were measured at room temperature. The maximum power factor was found for the films grown at 0.071 V with a value of 3421 705 mW m1 K2 and a thermal conductivity of 0.56 0.06 W m1 K1. Even better, when it can be done by employing a technique that is easily scalable to an industrial level and allows large areas to be obtained, such as electrodeposition. Finally, films with similar properties were deposited on a flexible Kapton substrate. A unileg thermoelectric power generator was produced with maximum output powers of 14.7, 29.4, and 37 mW under temperature differences of 10, 15, and 19 K, respectively; and maximum power densities of 55.1, 110.1, and 138.6 mW m2 under temperature differences of 10, 15, and 19 K, respectively., The authors would like to acknowledge financial support from MAT2017-86450-C4-3-R and CSIC PIF 2D-MESES. Cristina V. Manzano would like to acknowledge funding from “Atracci´on de Talento Investigador” de la Comunidad de Madrid, contract 2019- T1/IND-13541. We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI). We acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and the EU (FEDER, FSE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Revisiting anodic alumina templates: From fabrication to applications

  • Ruiz-Clavijo, Alejandra
  • Caballero-Calero, Olga
  • Martín-González, Marisol
Anodic porous alumina, -AAO- (also known as nanoporous alumina, nanohole alumina arrays, -NAA- or nanoporous anodized alumina platforms, -NAAP-) has opened new opportunities in a wide range of fields, and is used as an advanced photonic structure for applications in structural coloration and advanced optical biosensing based on the ordered nanoporous structure obtained and as a template to grow nanowires or nanotubes of different materials giving rise to metamaterials with tailored properties. Therefore, understanding the structure of nanoporous anodic alumina templates and knowing how they are fabricated provide a tool for the further design of structures based on them, such as 3D nanoporous structures developed recently. In this work, we review the latest developments related to nanoporous alumina, which is currently a very active field, to provide a solid and thorough reference for all interested experts, both in academia and industry, on these nanostructured and highly useful structures. We present an overview of theories on the formation of pores and self-ordering in alumina, paying special attention to those presented in recent years, and different nanostructures that have been developed recently. Therefore, a wide variety of architectures, ranging from ordered nanoporous structures to diameter changing pores, branched pores, and 3D nanostructures will be discussed. Next, some of the most relevant results using different nanostructured morphologies as templates for the growth of different materials with novel properties and reduced dimensionality in magnetism, thermoelectricity, etc. will be summarised, showing how these structures have influenced the state of the art in a wide variety of fields. Finally, a review on how these anodic aluminium membranes are used as platforms for different applications combined with optical techniques, together with principles behind these applications will be presented, in addition to a hint on the future applications of these versatile nanomaterials. In summary, this review is focused on the most recent developments, without neglecting the basis and older studies that have led the way to these findings. Thus, it gives an updated state-of-the-art review that should be useful not only for experts in the field, but also for non-specialists, helping them to gain a broad understanding of the importance of anodic porous alumina, and most probably, endow them with new ideas for its use in fields of interest or even developing the anodization technique., The authors would like to acknowledge the project MAT2017- 86450-c4-3-r, PIE-201950E057, and CAM18-PRE-IMN-001 fellowship of ARC. We also acknowledge the support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal conductivity reduction by nanostructuration in electrodeposited CuNi alloys

  • Manzano, Cristina V.
  • Caballero-Calero, Olga
  • Martín-González, Marisol
In the last few years, the use of inexpensive and scalable materials in industry for thermoelectric applications has received great interest, such as CuNi alloys. In this work, nanocrystalline CuNi alloys with different compositions were grown by pulsed electrodeposition. The incorporation of saccharine in the electrolyte allowed reduction of the crystallite size of CuNi down to 30¿40 nm. The thermoelectric properties, such as the electrical conductivity, Seebeck coefficient, and thermal conductivity of these nanocrystalline alloys, were studied. The maximum figure of merit obtained at room temperature was (6.1 1.4) 102 for nanocrystalline Cu0.55Ni0.45. The thermal conductivity of CuNi alloys was reduced by the nanostructuration to a value of 9.0 0.9 W m1 K1, making these nanocrystalline CuNi alloys more competitive than other more classical thermoelectric materials. This work opens a new field to be investigated, that can be described as the use of commercial alloys such as CuNi for thermoelectric applications and shows the use of a new approach to enhance the thermoelectric properties of inexpensive and/or fewer pollutant materials, The authors would like to acknowledge financial support from MAT2017-86450-C4-3-R. C. V. M. acknowledges financial support from Juan de la Cierva Incorporacio´n grants (IJCI-2017-31350) and P. C.-S. acknowledges financial support from CSIC JAEINT19_EX_0606 grant. We acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and EU (FEDER, FSE). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Environmentally Friendly Thermoelectric Materials: High Performance from Inorganic Components with Low Toxicity and Abundance in the Earth

  • Caballero-Calero, Olga
  • Ares, José R.
  • Martín-González, Marisol
This review article gives an overview of the recent research directions in eco-friendly, non-toxic, and earth-abundant thermoelectric materials. It covers materials such as sulfides, tetrahedrites, earth-abundant oxides, silicides, copper iodine, Half-Heusler intermetallic compounds, nitrides, and other environmentally friendly thermoelectrics. In all cases, their history, structure, general characteristics, thermoelectric properties, synthesis methods, and related thermoelectric applications are compiled. It is also shown that they are starting to be an excellent alternative for producing cost-effective, sustainable, and non-toxic thermoelectric generators. This review does not try to include all possible materials, but to show that there are high zT thermoelectric materials that are starting to be an excellent alternative for producing cost-effective, sustainable, and non-toxic thermoelectric generators., O.C.-C. and M.M.-G. would like to acknowledge financial support from MAT2017-86450-C4-3-R and the 2D_MESES project from CSIC, and J.R.A., from RTI2018-099794-B-I100.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effects of nanostructuration on the electrochemical performance of metallic bioelectrodes

  • Mobini, Sahba
  • González Sagardoy, María Ujué
  • Caballero-Calero, Olga
  • Patrick, Erin E.
  • Martín-González, Marisol
  • García-Martín, José Miguel
The use of metallic nanostructures in the fabrication of bioelectrodes (e.g., neural implants) is gaining attention nowadays. Nanostructures provide increased surface area that might benefit the performance of bioelectrodes. However, there is a need for comprehensive studies that assess electrochemical performance of nanostructured surfaces in physiological and relevant working conditions. Here, we introduce a versatile scalable fabrication method based on magnetron sputtering to develop analogous metallic nanocolumnar structures (NCs) and thin films (TFs) from Ti, Au, and Pt. We show that NCs contribute significantly to reduce the impedance of metallic surfaces. Charge storage capacity of Pt NCs is remarkably higher than that of Pt TFs and that of the other metals in both morphologies. Circuit simulations of the electrode/electrolyte interface show that the signal delivered in voltage-controlled systems is less filtered when nanocolumns are used. In a current-controlled system, simulation shows that NCs provide safer stimulation conditions compared to TFs. We have assessed the durability of NCs and TFs for potential use in vivo by reactive accelerated aging test, mimicking one-year in vivo implantation. Although each metal/morphology reveals a unique response to aging, NCs show overall more stable electrochemical properties compared to TFs in spite of their porous structure., This work was supported by European Commission (Ref. 793102-NeuPES-H2020-MSCA-IF-2017), Comunidad de Madrid (Atracción de Talento Programme, Modalidad-1 Ref. 2019-T1/ IND-1335), and CSIC (ILINK+2020 Ref. LINKA20342). The authors would also like to acknowledge the service from the MiNa Laboratory at IMN, funded from CM (project SpaceTec, S2018/NMT-4291 TEC2SPACE), MINECO (project CSIC13- 4E-1794), and EU (FEDER, FSE). O. C–C and M. M-G would like to acknowledge financial support from project MAT2017- 86450-c4-3-r., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Pulsed current-voltage electrodeposition of stoichiometric Bi2Te3 nanowires and their crystallographic characterization by transmission electron backscatter diffraction

  • Manzano, Cristina V.
  • Polyakov, Mikhail N.
  • Maiz, Jon
  • Aguirre Myriam H.
  • Maeder, Xavier
  • Martín-González, Marisol
Bi2Te3 nanowires with diameters ranging from 25 to 270 nm, ultra-high aspect ratio, and uniform growth front were fabricated by electrodeposition, pulsing between zero current density during the off time and constant potential during the on time (pulsed-current-voltage method, p-IV). The use of zero current density during the off time is to ensure no electrodeposition is carried out and the system is totally relaxed. By this procedure, stoichiometric nanowires oriented perpendicular to the c-axis is obtained for the different diameters of porous alumina templates. In addition, the samples show a uniform growth front with ultra-high aspect ratio single crystal nanowires. The high degree of crystallinity was verified by transmission electron backscatter diffraction. This characterization revealed that the nanowires present both large single crystalline areas and areas with alternating twin configurations.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Polyethylene three-dimensional nano-networks: How lateral chains affect metamaterial formation

  • Resende, P.M.
  • Gutiérrez-Fernández, E.
  • Aguirre, M.H.
  • Nogales, A.
  • Martín-González, M.
Polymers occupy a central role in current society due to their utility and versatile properties. As part of the class of soft materials, polymers have also been employed in research through nanostructuration and functionalization, looking for the development of new metamaterials with wide applicability in science and society. A particular polymer, Polyethylene, has been widely used both in research and commodities, and new ways to nanostructure and improve its functionality should be considered. Here, we report on the nanostructuration of polyethylene for the fabrication of three-dimensional nanonetworks, by resorting to 3 different variants of polyethylene: low density, high density, and ultra-high molecular weight. Through the melt infiltration of these polymers into well-known three-dimensional interconnected anodic aluminum oxide templates (3D-AAO), a study can be performed to understand the effects of the chain length, structure, and chain-branching of the used polymers on the stability and integrity of the resulting polymeric nanonetworks. This was accomplished by performing infiltrations in the presence of excess bulk material and quenching the infiltration process to access transient infiltration stages. The morphology of these networks was analyzed through SEM and STEM-HAADF to understand the differences arising from polymer structure. The observed results are interpreted through the use of the Lucas-Washburn equation for capillary flow and the determination of the critical contact angle for spontaneous capillary infiltration. The resulting metamaterials also exhibit photonic responses, resulting from the replication of the periodic nature of the employed templates.