Pasar al contenido principal

INTERFACIAL MAGNETISM FOR ULTRAFAST AND LOW DISSIPATION SIGNAL PROCESSING DEVICES

RTI2018-095303-A-C52

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 46
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Generation of defective few-layered graphene mesostructures by high-energy ball milling and their combination with FeSiCuNbB microwires for reinforcing microwave absorbing properties

  • López Sánchez, Jesús
  • Peña Moreno, Álvaro
  • Serrano, Aída
  • Del Campo, Adolfo
  • Rodríguez De La Fuente, Óscar
  • Carmona Tejero, Noemí
  • Matatagui Cruz, Daniel
  • Horrillo, María del Carmen
  • Rubio Zazo, Juan
  • Navarro Palma, Elena
  • Marín Palacios, María Pilar
Defective few-layered graphene mesostructures (DFLGMs) are produced from graphite flakes by high-energy milling processes. We obtain an accurate control of the generated mesostructures, as well as of the amount and classification of the structural defects formed, providing a functional material for microwave absorption purposes. Working under far-field conditions, competitive values of minimum reflection loss coefficient (RL_(min)) = −21.76 dB and EAB = 4.77 dB are achieved when DFLGMs are immersed in paints at a low volume fraction (1.95%). One step forward is developed by combining them with the excellent absorption behavior that offers amorphous Fe_(73.5)Si_(13.5)B_(9)Cu_(1)Nb microwires (MWs), varying their filling contents, which are below 3%. We obtain a RLmin improvement of 47% (−53.08 dB) and an EAB enhancement of 137% (4 dB) compared to those obtained by MW-based paints. Furthermore, a f_(min) tunability is demonstrated, maintaining similar RL_(min) and EAB values, irrespective of an ideal matching thickness. In this scenario, the Maxwell-Garnet standard model is valid, and dielectric losses mainly come from multiple reflections, interfacial and dielectric polarizations, which greatly boost the microwave attenuation of MWs. The present concept can remarkably enhance not only the MW attenuation but can also apply to other microwave absorption architectures of technological interest by adding low quantities of DFLGMs.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards blue long-lasting luminescence of Eu/Nd-doped calcium-aluminate nanostructured platelets via the molten salt route

  • Rojas-Hernández, Rocío E.
  • Rubio Marcos, Fernando
  • Serrano Rubio, Aída
  • Salas, Eduardo
  • Hussainova, Irina
  • Fernández Lozano, José Francisco
Calcia-alumina binary compounds doped with rare earths and some transition metals cations show persistent luminescence from the visible to the infrared range. Specifically, the blue light can be obtained through the Eu2+ activator center in a potential host, such as dodecacalcium hepta-aluminate (Ca12Al14O33) and monocalcium aluminate (CaAl2O4). By doping with Nd3+, the persistent luminescence can be substantially prolonged; for this reason, the Eu/Nd pair is a potential choice for developing long-lasting blue luminescence. Herein, the phase evolution of the calcia-alumina system via molten salt synthesis is reported as a function of the synthesis temperature and the atmospheric environment. The fraction of CaAl2O4 phase increases when the temperature is higher. Synthesized microparticles of platelet-type morphology represent isolated nanostructured ceramic pieces. Under visible light, the particles are white. This indicates that the followed process solves the dark-gray coloring of phosphor when is synthesized in a reduced atmosphere at high temperature. As regards the synthesis mechanism, which is assisted by the molten flux, the dissolution−diffusion transport process is promoted at the surface of the alumina microparticles. In fact, the emission intensity can be modulated through the phase of the Eu-doped calcium-aluminate discrete platelets synthesized. Consequently, the photoluminescence intensity depends also on the oxidation state of the Eu ion. X-ray absorption near-edge structure and photoluminescence measurements corroborate the Eu reduction and the grain coarsening with the enhancement of the blue emission. The doped phosphors with Eu/Nd show a broad and strong absorption in the region of 320–400 nm and a broad emission band at around 440 nm when they are excited in this absorption range. From a broader perspective, our findings prove that the Ca12Al14O33 and CaAl2O4 phases open new opportunities for research into the design of blue long-lasting emitters for a wide range of fields from ceramic to optoelectronic materials., This work was supported by the Spanish Ministry of Science Innovation and Universities (MICIU) under the projects MAT2017-86450-C4-1-R and RTI2018-095303-A-C52, and the Spanish National Research Council (CSIC) under the project NANOMIND CSIC 201560E068. R.E.R.-H. acknowledges the financial support of the Mobilitas Pluss program in the framework of the MOBJD254 project. F.R.-M. is indebted to MINECO for a ‘Ramon y Cajal’ contract (ref: RyC-2015-18626), which is co-financed by the European Social Fund. F.R.-M. also acknowledges support from a 2018 Leonardo Grant for Researchers and Cultural Creators, BBVA Foundation. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395). The support of ETAG through PUT1063 (I. Hussainova) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Expanding the tunability and applicability of exchange-coupled/decoupled magnetic nanocomposites

  • Granados-Miralles, Cecilia
  • Quesada, Adrián
  • Saura-Múzquiz, Matilde
  • Andersen, Henrik L.
  • Fernández Lozano, José Francisco
  • Christensen, Mogens
  • AMPHIBIAN Project ID:720853
[EN] CoFe2O4/Co–Fe magnetic composites are usually prepared through partial reduction of CoFe2O4, which often yields monoxides (i.e., FeO, CoO) as secondary phases. Since these compounds are paramagnetic at ambient conditions, the presence of a small amount of monoxide is generally downplayed in the literature, and the possible effects on the magnetic properties are simply ignored. However, the present study shows that even a low concentration of monoxide results in decoupling of the soft and hard magnetic phases, which inevitably leads to a deterioration of the magnetic properties. Additionally, it is confirmed that a partial reduction of CoFe2O4 is a suitable method to produce CoFe2O4/Co–Fe nanocomposites, provided that the treatment is well controlled with respect to duration, temperature and flow of reductant. A monoxide-free nanocomposite was produced and its magnetic properties evaluated both at room and low temperature. Our model system exemplifies the potential of exchange-coupling (and decoupling) as a tool to tune the magnetic properties of a material within a relatively wide range of values, thus widening its spectrum of potential applications., C. G.-M. and A. Q. have contributed equally to this work. The authors would like to thank financial support from the European Commission through the AMPHIBIAN project (H2020-NMBP-2016-720853), the Danish National Research Foundation (Center for Materials Crystallography, DNRF-93), and the Spanish Ministerio de Ciencia, Innovación y Universidades (RTI2018-095303-A-C52). C. G.-M. acknowledges financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades through the Juan de la Cierva Program (FJC2018- 035532-I). Authors from Aarhus University gratefully acknowledge affiliation with the Center for Integrated Materials Research (iMAT) at Aarhus University. We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the growth conditions on the magnetism of SrFe12O19thin films and the behavior of Co/SrFe12O19bilayers

  • Delgado Soria, Guiomar
  • Marco, J.F.
  • Mandziak, Anna
  • Sánchez-Cortés, Santiago
  • Sánchez-Arenillas, M.
  • Prieto, J. E.
  • Dávalos, J.Z.
  • Foerster, M.
  • Aballe, Lucía
  • López-Sánchez, Jesús
  • Guzmán-Mínguez, J. C.
  • Granados-Miralles, Cecilia
  • de la Figuera, Juan
  • Quesada, Adrián
  • AMPHIBIAN Project ID:720853
11 pags., 12 figs. 1 tab., SrFe12O19 (SFO) films grown on Si (100) substrates by radio-frequency magnetron sputtering have been characterized in terms of composition, structural and magnetic properties by a combination of microscopy, diffraction and spectroscopy techniques. Mössbauer spectroscopy was used to determine the orientation of the films magnetization, which was found to be controlled by both the sputtering power and the thickness of the films. Additionally, the coupling between the SFO films and a deposited cobalt overlayer was studied by means of synchrotron-based spectromicroscopy techniques. A structural coupling at the SFO/Co interface is suggested to account for the expetimental observations. Micromagnetic simulations were performed in order to reproduce the experimental behaviour of the system., This work is supported by the Spanish Ministry of Science, Innovation and Universities through Projects RTI2018- 095303-B-C51, RTI2018-095303-B-C53 and RTI2018- 095303-A-C52 (MCIU/AIE/FEDER,EU) and by the European Comission through Project H2020 No. 720853 (Amphibian) and by the Regional Government of Madrid through project S2018-NMT-4321. C.G-M. acknowledges financial support from MICINN through the “Juan de la Cierva” program (FJC2018-035532-I). Technical support of the technical staff of CIRCE beamline of the ALBA Synchrotron Light Facility is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crystal defects and optical emissions of pulse electrodeposited ZnO

  • Manzano, Cristina V.
  • Serrano Rubio, Aída
  • Muñoz-Noval, Alvaro
  • Fernández Lozano, José Francisco
  • Martín-González, Marisol
ZnO has been widely studied in the last decades as an n-type semiconductor due to its wide application range, for example, in optoelectronics, solar cells, light-emitting diodes, thermoelectrics, amongst others. The material efficiency for certain applications is highly dependent on the presenting film morphology. Electrodeposition is well-known as a technique with precise control over the structural and morphological properties of the obtained materials. When the structural and morphological properties are tuned, it is possible to find a wide variety of defects in the ZnO structure. In this study, ZnO films were grown using pulsed electrodeposition with variation of the reduction potential. The crystal order, structural defects and optical emissions of the films have been analyzed by X-Ray Diffraction (XRD), X-ray Absorption Near-Edge Structure (XANES), Extended X-ray Absorption Fine Structure (EXAFS) and Photoluminescence (PL). ZnO film grown at less negative reduction potential presents a stronger texture along [0001] by XRD, higher crystalline order, and more zinc vacancies by XANES and EXAFS. The films obtained at less negative potential present less OH trapped in the ZnO structure and a relatively higher level of defects O, O, O and O than those grown at higher reduction potentials by PL. This will be related to the fact that at less negative potentials there is less concentration of OH at the film surface than at more negative potentials. The combination of X-ray absorption spectroscopy and photoluminescence reveals the complicated nature of the atomic defect in electrodeposited ZnO films. Allowing to evidence the preferential presence of atomic defect as a function of the reduction potential. In this work, we have also compared those defects with reference compounds such as a Zn foil and ZnO polycrystalline powder., The authors would like to acknowledge financial support from MAT2017-86450-C4-1-R, MAT2017-86450-C4-3-R, and RTI2018-095303-A-C52. C.V.M acknowledges financial support from Juan de la Cierva Incorporación grants IJCI-2017-31350. A.S. and A.M.N. acknowledge the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract No. 2017-t2/IND5395 and 2018-T1/IND-10360, respectively. We acknowledge The European Synchrotron (ESRF), MICIU, and CSIC for provision of synchrotron radiation facilities in using the BM25-SpLine beamline. We also thank the BM25-SpLine staff for the technical support beyond their duties. We acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794) and EU (FEDER, FSE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

New insights into the structural analysis of maghemite and (MFe2O4, M = Co, Zn) ferrite nanoparticles synthesized by a microwave-assisted polyol process

  • Gallo-Cordova, Álvaro
  • Espinosa, Ana
  • Serrano Rubio, Aída
  • Gutiérrez, Lucía
  • Menéndez, Nieves
  • Morales, María Del Puerto
  • Mazarío, Eva
[EN] The search for more efficient, scalable, reproducible and standardized synthesis methods able to control particle size and crystallinity is still a challenge in nanotechnology. The one-pot microwave-assisted polyol process has been optimized for the synthesis of well-defined ferrite nanoparticles. Highly uniform and crystalline γ-Fe2O3, CoFe2O4 and ZnFe2O4 nanoparticles, with diameters below 14 nm have been prepared by an easy and reproducible one-pot microwave-assisted heating procedure in a polyol medium. A pure single phase and cubic spinel structure were confirmed by powder X-ray diffraction and Raman spectroscopy. Depending on the metal precursors, nanoparticles display magnetic features from superparamagnetic behaviour (Fe- A nd Zn-ferrites) to ferrimagnetism (Co ferrite) at room temperature. The iron oxidation state of 3+ and its short-range order coordination were studied by XAS (X-ray absorption spectroscopy). External field Mössbauer spectra, recorded at low temperature, confirmed the ferrimagnetic order with a Fe3+ and M2+ partial cationic distribution within both the A and B sites in zinc and cobalt ferrite, respectively. According to these results, the ferrite stoichiometry was (Zn0.70Fe0.30)[Zn0.30Fe1.70]O4 and (Co0.28Fe0.72)[Co0.72Fe1.28]O4. This journal is, This research was funded by the Spanish Ministry of Economy and Competitiveness under grants MAT2017-88148-R, MAT2017-86540-C4-1-R, RTI2018-095303-A-C52, and PGC2018-095642-B-I00. E. M. acknowledges financial support from the Juan de la Cierva Formación (FJCI-2015-23702) and to Comunidad de Madrid – Jóvenes Doctores project (SI1-PJI-2019-00366). L. G. acknowledges financial support from the Ramón y Cajal program (RYC-2014-15512). The authors would like to acknowledge the use of the Advanced Microscopy Laboratory (INA-Universidad de Zaragoza). A. S. and A. E. acknowledge financial support from the Comunidad de Madrid for the ‘‘Atracción de Talento Investigador’’ contracts (No. 2017-T2/IND5395 and 2018-T1/IND10058). A. E. is also grateful to the 2018/NMT-4321 and SEV-2016-0686 projects. The European Synchrotron (ESRF),Ministerio Español de Ciencia, Innovación y Universidades (MCIU) and Consejo Superior de Investigaciones Cientificas (CSIC) are acknowledged for the provision of synchrotron radiation facilities. We also thank the BM25- SpLine staff for the technical support beyond their duties.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cold sintering process of ZnO ceramics: Effect of the nanoparticle/microparticle ratio

  • Serrano Rubio, Aída
  • Caballero-Calero, Olga
  • García García-Tuñón, Miguel Ángel
  • Lazić, Snežana
  • Carmona, N.
  • Castro, Germán R.
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
We show the efficiency in the preparation of >95 % dense ZnO ceramics by cold sintering process through the incorporation of ZnO nanoparticles in the 1−10 wt% range at temperatures of 170 °C, pressures of 750 MPa and a pellet height/diameter ratio of 0.38. Morphological, structural and physical properties are dependent on the amount of ZnO nanoparticles incorporated into the system. After the densification by cold sintering process, ZnO ceramics show a reduction of the average valence indicating the deficiency of oxygen, similar to ceramics sintered by the conventional route. Besides, the generation of structural disorder and modifications into the ZnO lattice are identified in sintered ceramics, inducing intrinsic defects related to the loss of oxygen ions, the diffusion of zinc and zinc vacancies, which depend on the sintering process and the starting powders. These characteristics influence the final functional properties of the sintered ZnO ceramics, such as the visible photoluminescence signal., This work has been supported by the Ministerio Español de Ciencia, Innovación y Universidades (MCIU) through the projects MAT2017-86540-C4-1-R, MAT2017-86540-C4-3-R and RTI2018-095303-A-C52. The European Synchrotron (ESRF), MCIU and Consejo Superior de Investigaciones Cientificas (CSIC) are acknowledged for the provision of synchrotron radiation facilities. We also thank the BM25-SpLine staff for the technical support beyond their duties. A.S. acknowledges financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Control of the Length of Fe73.5Si13.5Nb3Cu1B9 Microwires to Be Used for Magnetic and Microwave Absorbing Purposes

  • Gueye,Papa Gorgui Birame
  • López-Sánchez, Jesús
  • Navarro, Elena
  • Serrano Rubio, Aída
  • Marín, Pilar
A combination of high-energy ball milling, vacuum filtering, and sedimentation processes has been demonstrated to be a useful approach to reduce, in a controlled way, the length of as-cast Fe73.5Si13.5Nb3Cu1B9 amorphous magnetic microwires (MWs) and annealed material at 550 °C in nitrogen conditions. Homogeneous compositional microstructures with fairly narrow size distributions between 1300 and 11.7 μm are achieved, exhibiting tunable response as a soft magnetic material and as a microwave absorber. From the magnetic perspective, the soft magnetic character is increased with smaller length of the MWs, whereas the remanence has the opposite behavior mainly due to the structural defects and the loss of the shape anisotropy. From the microwave absorption perspective, a novel potential applicability is tested in these refined microstructures. This innovation consists of coatings based on commercial paints with a filling percentage of 0.55% of MWs with different lengths deposited on metallic sheets. Large attenuation values around −40 dB are obtained in narrow spectral windows located in the GHz range, and their position can be varied by combining different optimized lengths of MW. As an example of this powerful mechanism for absorbing microwaves at specific frequencies, MW lengths of 2 mm and 50 μm are chosen, where precise tailoring of the minimum reflection loss (RL) is obtained in a range between 8.85 and 13.25 GHz. To confirm these experimental results, an effective medium standard model proposed for electrical permittivity is used. Experimental and theoretical results are consistent and these novel composites are also proposed as a feasible candidate for designing frequency-selective microwave absorbers on demand, with low filling percentages and high absorption intensity values., The authors acknowledge the financial support from the Spanish Ministry of Science, Innovation and Universities under the projects RTI2018-095856-B-C21, MAT2017-86540-C4-1-R, and RTI2018-095303-A-C52 and from Comunidad de Madrid NANOFRONTMAG S2013/MIT-2850 and NANOMAGCOST S2018/NMT-4321. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (no. 2017-t2/IND5395)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

FeCo nanowire−strontium ferrite powder composites for permanent magnets with high-energy products

  • Guzmán-Mínguez, J. C.
  • Ruiz-Gómez, Sandra
  • Vicente-Arche, L. M.
  • Granados-Miralles, Cecilia
  • Fernández-González, Claudia
  • Mompean, Federico J.
  • García-Hernández, Mar
  • Erohkin, S.
  • Berkov, Dmitry
  • Mishra, D.
  • de Julián Fernández, C.
  • Fernández Lozano, José Francisco
  • Pérez, L.
  • Quesada, Adrián
  • AMPHIBIAN Project ID:720853
Due to the issues associated with rare-earth elements, there arises a strong need for magnets with properties between those of ferrites and rare-earth magnets that could substitute the latter in selected applications. Here, we produce a high remanent magnetization composite bonded magnet by mixing FeCo nanowire powders with hexaferrite particles. In the first step, metallic nanowires with diameters between 30 and 100 nm and length of at least 2 μm are fabricated by electrodeposition. The oriented as-synthesized nanowires show remanence ratios above 0.76 and coercivities above 199 kA/m and resist core oxidation up to 300 °C due to the existence of a >8 nm thin oxide passivating shell. In the second step, a composite powder is fabricated by mixing the nanowires with hexaferrite particles. After the optimal nanowire diameter and composite composition are selected, a bonded magnet is produced. The resulting magnet presents a 20% increase in remanence and an enhancement of the energy product of 48% with respect to a pure hexaferrite (strontium ferrite) magnet. These results put nanowire−ferrite composites at the forefront as candidate materials for alternative magnets for substitution of rare earths in applications that operate with moderate magnet performance., We would like to thank Dr. Vić tor Fuertes for his advice on the processing of the bonded magnets. This work is supported by the Spanish Ministerio de Economía y Competitividad y Ministerio de Ciencia e Innovación (Project Nos. MAT2017- 86450-C4-1-R, MAT2015-64110-C2-1-P, MAT2015-64110- C2-2-P, MAT2017-87072-C4-2-P, RTI2018-095303-A-C52, and FIS2017-82415-R) and by the European Commission through Project H2020 (No. 720853; AMPHIBIAN). C.G.-M. acknowledges financial support from MICINN through the “Juan de la Cierva” Program (FJC2018-035532-I). A.Q. acknowledges financial support from MICINN through the “Ramón y Cajal” Program (RYC-2017-23320). The work also is funded by the Regional Government of Madrid (Project S2018/ NMT-4321; NANOMAGCOST)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Boosting the coercivity of SrFe12O19 nanocrystalline powders obtained using the citrate combustion synthesis method

  • Guzmán-Mínguez, J. C.
  • Moreno Arche, L.
  • Granados-Miralles, Cecilia
  • López-Sánchez, Jesús
  • Marín, Pilar
  • Fernández Lozano, José Francisco
  • Quesada, Adrián
  • AMPHIBIAN Project ID:720853
Strontium hexaferrite nanocrystalline powders were synthesized using a citrate combustion method and subsequently subjected to post-synthesis processing with the aim of tuning the micro-nanostructure to improve the magnetic properties. Firstly, the synthesis thermal treatments were optimized in order to minimize the formation of secondary phases, mainly hematite. Secondly, the as-synthesized powders were conditioned by a two-step process: ball milling in wet medium (ethanol) and high-speed mixing. The final processed powders exhibited a saturation magnetization of 74 emu g-1 and a coercivity of 6450 Oe. Following a low-temperature combustion synthesis, the coercivity is one of the largest values reported for strontium ferrites. The combination of the two-step conditioning procedure results in a useful methodology to obtain SrFe12O19 nanocrystalline powders with competitive properties. The morphological, structural and magnetic properties of the processed material make it a promising candidate for hard-soft ferrite-based composite magnets, where large coercivity values are highly desirable., This work is supported by the Spanish Ministerio de Ciencia e Innovación through Project Nos. MAT2017-86450-C4-1-R, RTI2018-095303-B-C51, RTI2018-095303-B-C53, RTI2018-095303-A-C52, and FIS2017-82415-R and through the Ramón y Cajal Contract RYC-2017-23320; and by the European Commission through Project H2020 No. 720853 (AMPHIBIAN). The work is funded as well by the Regional Government of Madrid through Project S2018/NMT-4321 (NANOMAGCOST). C G-M acknowledges financial support from MICINN through the ‘Juan de la Cierva’ Program (FJC2018-035532-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Uncorrelated magnetic domains in decoupled SrFe12O19/Co hard/soft bilayers

  • Delgado Soria, Guiomar
  • Granados-Miralles, Cecilia
  • Mandziak, Anna
  • Jenus, P.
  • Saura-Múzquiz, Matilde
  • Christensen, Mogens
  • Foerster, Michael
  • Aballe, Lucía
  • Fernández Lozano, José Francisco
  • de la Figuera, Juan
  • Quesada, Adrián
  • AMPHIBIAN Project ID:720853
8 pags., 5 figs., Composites of magnetically hard and soft phases are present in multiple and diverse applications, ranging from bulk permanent magnets in motors and generators to state-of-the-art recording media devices. The nature of the magnetic coupling between the hard and soft phases is of great technological relevance, as the macroscopic properties of the functional composite material ultimately depend on the atomic-scale interactions between phases. In this work, the hard/soft bilayer system SrFeO/Co has been studied based on photoemission electron microscopy combined with x-ray absorption and magnetic circular dichroism. Our experiments show that the magnetization of the hard magnetic oxide has a direction perpendicular to the layer plane, whereas the magnetization of the soft metallic overlayer remains in-plane. As a consequence, the magnetic domain patterns observed for the hard and soft phases are very different and completely uncorrelated to one another, indicating that no soft spins align with the hard phase by pure magnetodipolar arguments. The results are understood as the consequence of an absence of exchange-coupling between phases, in a scenario in which the shape anisotropy of the soft layer overcomes the Zeeman energy of the perpendicular magnetic field generated by the hard ferrite. Micromagnetic simulations of our system predict that low degrees of exchange-coupling effectively prevent substantial softening of the composite and lead to the alignment of soft and hard magnetic moments. A strategy thus emerges for the development of future hard-soft magnets, based on minimizing the degree of exchange-coupling while avoiding complete uncoupling., This work is supported by the Spanish Ministerio de Economía y Competitividad (MINECO) through Projects no. MAT2017-86450-C4-1-R, RTI2018-095303-B-C51, RTI2018-095303-B-C53, RTI2018-095303-A-C52, and FIS2017-82415-R and by the European Comission through Project H2020 no. 720853 (AMPHIBIAN). The work is funded as well by the Regional Government of Madrid through Project S2018/NMT-4321 (NANOMAGCOST). C.G.-M. acknowledges financial support from Spanish Ministerio de Ciencia e Innovación (MICINN) through the 'Juan de la Cierva' Program (FJC2018-035532-I). Spanish Ministerio de Economía y Competitividad (MINECO)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Scaling up the production of electrodeposited nanowires: A roadmap towards applications

  • Fernández-González, Claudia
  • Guzmán-Mínguez, J. C.
  • Guedeja-Marrón, A
  • García-Martín, Eduardo
  • Foerster, Michael
  • Niño, Miguel Ángel
  • Aballe, Lucía
  • Quesada, Adrián
  • Pérez, Lucas
  • Ruiz-Gómez, Sandra
  • AMPHIBIAN Project ID:720853
11 pags., 5 figs., 1 tab. -- This article belongs to the Special Issue Multifunctional Magnetic Nanowires and Nanotubes, The use of metallic nanowires is mostly reduced to scientific areas where a small quantity of nanostructures are needed. In order to broaden the applicability of these nanomaterials, it is necessary to establish novel synthesis protocols that provide a larger amount of nanowires than the conventional laboratory fabrication processes at a more competitive cost. In this work, we propose several modifications to the conventional electrochemical synthesis of nanowires in order to increase the production with considerably reduced production time and cost. To that end, we use a soft anodization procedure of recycled aluminum at room temperature to produce the alumina templates, followed by galvanostatic growth of CoFe nanowires. We studied their morphology, composition and magnetic configuration, and found that their properties are very similar to those obtained by conventional methods., This research was partially funded by the Spanish Agencia Estatal de Investigación through projects MAT2017-87072-C4-2-P and RTI2018-095303-B-C53, by The Ministerio de Ciencia y Universidades through project RTI2018-095303-A-C52, through the Ramón y Cajal Contract RYC2017-23320, The European Commission through the H2020 Project No. 720853 (AMPHIBIAN) and by the Comunidad de Madrid through Project NANOMAGCOST-CM P2018/NMT-4321.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Progress and prospects of hard hexaferrites for permanent magnet applications

  • Julián Fernández, César de
  • Sangregorio, Claudio
  • de la Figuera, Juan
  • Belec, B.
  • Makovec, D.
  • Quesada, Adrián
  • AMPHIBIAN Project ID:720853
30 pags., 22 figs., 2 tabs., Permanent magnets based on hard hexaferrite represent the largest family of magnets being used today by volume. They generate moderate remanence induction, but present crucial advantages in terms of availability, cost, resistance to demagnetization and corrosion and absence of eddy current losses. As a consequence, ferrites are the most logical candidate for substitution of rare-earths in selected applications that do not demand the best performing magnets. If the remanence of ferrite-based magnets was to be improved, even mildly, the door to a larger scale substitution could be opened. In this framework, we review here current strategies to improve the properties of hexaferrites for permanent magnet applications. We first discuss the potential of exploring the nanoscale. Second, progress related to controllably doping hexaferrites is revised. Third, results achieved by fabricating hard-soft magnetic composites using ferrites as the hard phase are presented. Finally, future prospects and new potential end applications for ferrite magnets are discussed., This work was supported by the Slovenian Research Agency through research programs Nos. P2-0089 and P2-0412 and project J2-8166, by the Spanish Ministry of Science and Innovation through projects RTI2018-095303-BC51 and RTI2018-095303-A-C52, by the European Commission through Project H2020 No. 720853 (Amphibian) and by the Regional Government of Madrid through project S2018-NMT-4321.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Heteropolyacids supported on boron nitride and carbon nitride for catalytic and catalytic photo-assisted alcohol dehydration

  • García-López, Elisa I.
  • Pomilla, Francesca R.
  • Krivtsov, Igor
  • Serrano, Aida
  • Liotta, Leonarda F.
  • Villar Rodil, Silvia
  • Paredes Nachón, Juan Ignacio
  • Marcì, Giuseppe
Keggin H3PW12O40 (PW12) and Wells-Dawson H6P2W18O60 (P2W18) heteropolyacids (HPAs) are photo(catalysts) for various acid-promoted and redox catalytic reactions. Their activity increases if they are deposited on certain supports as metal oxides or carbon materials. Although the surface area and acid-base interactions of the HPAs with supports are considered as key factors for the performance of the binary material, the role of the local structure changes in the HPAs upon their immobilization on solids must be also of primary importance, directly affecting both acidity and photoredox properties. Here, the (photo)catalytic performance of Keggin and Wells-Dawson heteropolytungstates supported on boron nitride (BN) and two types of carbon nitride (C3N4) in the gas-solid 2-propanol dehydration to propene has been studied. Apart from characterizing the materials by a set of conventional laboratory-scale structural and physical-chemical techniques, an insight into the variations of the local structure of supported HPAs is provided by means of X-ray absorption spectroscopy (XAS), and their influence on the supported HPAs (photo)catalytic activity is discussed. The irradiation with UV light increased the activity of both heteropolytungstates with respect to the catalytic experiments. The apparent activation energy calculated for the photo-assisted process resulted always lower with respect to that obtained for the catalytic one alone. Moreover, the materials that showed the highest apparent turnover frequency (TOF) were those in which the HPAs were impregnated on graphitic C3N4 or on BN and, in particular, the highest TOF values were observed at the highest temperature for the PW12/BN and P2W18/BN samples. Interestingly, the highest activity of HPAs supported on BN seems to be due to the stabilization of the W octahedral coordination, according to the XAS data., LFL is grateful to progetto di Ricerca ARS01_00637 Energie per l’Ambiente-TARANTO (PNR 2015-2020) for financial support. IK acknowledges support by Spanish MINECO (MAT2016-78155-C2-1-R), Gobierno del Principado de Asturias (GRUPIN-ID2018-170) and the Alexander von Humboldt Foundation through the Humboldt Research Fellowship. S.V.-R. and J.I.P. acknowledge financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades (MCIU), the Spanish Agencia Estatal de Investigación and European Regional Development Fund (ERDF) through project RTI2018-100832B-I00, and partial funding by Plan de Ciencia, Tecnología e Innovación (PCTI) 2013-2017 del Principado de Asturias and the ERDF (project IDI/2018/000233). A.S acknowledges financial support from the MCIU through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52 and from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017t2/IND5395). The European Synchrotron (ESRF), MCIU and Consejo Superior de Investigaciones Científicas (CSIC) are also acknowledged for the provision of synchrotron radiation facilities. We also thank the BM25-SpLine staff for the technical support beyond their duties., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Further progress in the study of epsilon iron oxide in archaeological baked clays

  • López-Sánchez, Jesús
  • Palencia-Ortas, A.
  • Campo, Ángel Adolfo del
  • McIntosh, G.
  • Kovacheva, M.
  • Martín Hernández, Fátima
  • Carmona, N.
  • Rodríguez de la Fuente, Óscar
  • Marín, Pilar
  • Molina‐Cardín, Alberto
  • Osete, María Luisa
  • AMPHIBIAN Project ID:720853
[EN] The occurrence of ε-FeO in archaeological samples that have been subjected to high temperatures is gradually being detected by the use of micrometric structural characterization techniques. This work provides new information by revealing that the ε-FeO is formed as a response to temperature, the aggregation state and the position within the baked clay with respect to the nearest heat source. In addition, depending mainly on the atmospheric environment, the temperature reached by the combustion structure, the distance from the heating source and the particle aggregation, other iron oxide magnetic phases are produced. In the baked clay studied here, hematite is found over the whole range of samples studied but its magnetic contribution is negligible. Magnetite is observed at the sample surface, probably due to local atmospheric environment closest to the combustion source. Maghemite is found at all depths up to 6 cm below the sample surface. ε-FeO has a limited distribution, found within 2–3 cm of the sample surface. Furthermore, the viability of this compound as a palaeofield marker has been evaluated in both archaeological and synthetic samples. The results indicate that ε-FeO is able to register the direction of the magnetic field. Linear palaeointensity plots have been obtained in synthetic samples, although the value of the palaeofield could be, sometimes, overestimated., The authors also acknowledge the financial support from the Spanish Ministry of Science, Innovation and Universities under the projects RTI2018-095856-B-C21, CGL2017-87015-P, CGL2017-92285-EXP, CGL2017-92285-EXP/BTE, MAT2017-86540-C4-1-R, MAT2017-87072-C4-2-P and RTI2018-095303-A-C52, from Comunidad de Madrid NANOFRONTMAG S2013/MIT-2850 and NANOMAGCOST S2018/NMT-4321, and from the European Commission under H2020 frame by AMPHIBIAN Project ID: 720853. APO thanks the Ministry of Economy, Industry and Competitiveness (PTA Contract)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improvement of the magnetic properties of SrFe12O19 ceramics by tailored sintering with SiO2 addition

  • Guzmán-Mínguez, J. C.
  • Vicente-Arche, L. M.
  • Granados-Miralles, Cecilia
  • Fernández Lozano, José Francisco
  • Quesada, Adrián
  • AMPHIBIAN Project ID:720853
[EN] In order to obtain competitive strontium ferrite sintered magnets, SiO2 and CaO are added to avoid exaggerated grain growth. Besides favoring proper densification, these additives prevent the collapse of coercivity associated to grain growth. However, these additives may lead to slight decreases in density and the formation of paramagnetic α-Fe2O3 that hampers magnetization. Here, with the motivation of simplifying the production process, we present a study to maximize the magnetic performance of strontium ferrite ceramics using silica as the sole additive. A microscopic study offers insights into the grain growth mechanism activated by Silica. As a result, a compromise between relative density, coercivity and saturation magnetization is attained. It is found that sintering for 4 h up to 1200 °C with a SiO2 content of 1 wt% leads to the best compromise between coercivity, magnetization and density values. Competitive densities are reported in the absence of CaO, the usual co-additive. In addition, Confocal Raman Microscopy is employed for the first time to characterize the decomposition of strontium ferrite onto α-Fe2O3-Fe2O3., This work is supported by the Spanish Ministerio de Ciencia, Innovación y Universidades through Project no. MAT2017-86450-C4-1-R, RTI2018-095303-A-C52 and through the Ramón y Cajal Contract RYC-2017-23320 and Juan de la Cierva Program FJC2018-035532-I; and by the European Commission through the H2020 Project no. 720853 (AMPHIBIAN).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Multiphase materials based on the Fe73.9Si15.5Cu1Nb3B6.6 alloy obtained by dry and wet high-energy ball milling processes

  • López-Sánchez, Jesús
  • Navarro, Elena
  • Rodríguez-Granado, Freddy
  • Serrano Rubio, Aída
  • Marín, Pilar
  • AMPHIBIAN Project ID:720853
[EN] Novel hybrid materials based on the soft nanocrystalline FeSiCuNbB alloy are designed in this work with the purpose of reducing its particle size and developing different compositional, structural, and magnetic properties depending on the high-energy ball milling time and route employed. Innovative processes combining mixer, vibratory and planetary motions at the same time are carried out under a dry and a wet route, obtaining reduced sub-micron particle size distributions after 2 h of milling. The established approach takes advantage of the nature of amorphous materials to promote the formation of different hybrid compounds and it is supported by the high virulence of the milling process performed at 2000 rpm. On the one hand, the results obtained by the dry route show a structural and magnetic evolution dominated by the presence of ferromagnetic α-FeSi nanocrystals. On the other hand, the wet approach that is supported by glycerol evidences the destruction of the α-FeSi with the milling time in favor of the non-magnetic β-FeSi phase, obtaining a new functionality for the FeSiCuNbB alloy. Their properties as soft magnetic alloys are evaluated and compared depending on the followed route, opening up a new physicochemical method in the development of multiphase compounds with potential applications. With this work, a controlled formation of different hybrid compounds is achieved, revealing an effective mechanism to introduce functional materials with different properties embedded in an amorphous ferromagnetic matrix., The authors acknowledge the Spanish Ministry of Industry, Economy and Competitiveness for financing the project MAT2015-65445-C2-1-R, MAT2017-86450-C4-1-R, MAT2015-67557-C2-1-P, RTI2018-095303-A-C52, and , the Comunidad de Madrid by S2013/MIT-2850 NANOFRONTMAG, and the European Commission under H2020 frame by AMPHIBIAN Project ID: 720853. In addition, the authors thank for the financial support from the Spanish Ministry of Science, Innovation and Universities (MICIU) and The Spanish National Research Council (CSIC) under Grant no. PIE 2010-6OE-013. A. S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (no. 2017-t2/IND5395)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On the potential of hard ferrite ceramics for permanent magnet technology-a review on sintering strategies

  • AMPHIBIAN Project ID:720853
  • Granados-Miralles, Cecilia
  • Jenuš, Petra
[EN] A plethora of modern technologies rely on permanent magnets for their operation, including many related to the transition towards a sustainable future, such as wind turbines or electric vehicles. Despite the overwhelming superiority of magnets based on rare-earth elements in terms of the magnetic performance, the harmful environmental impact of the mining of these raw materials, their uneven distribution on Earth and various political conflicts among countries leave no option but seeking for rare-earth-free alternatives. The family of the hexagonal ferrites or hexaferrites, and in particular the barium and strontium M-type ferrites (BaFe12O19 and SrFe12O19), are strong candidates for a partial rare-earth magnets substitution, and they are indeed successfully implemented in multiple applications. The manufacturing of hexaferrites into dense pieces (i.e. magnets) meeting the requirements of the specific application (e.g. magnetic and mechanical properties, shape) is not always straightforward, which has in many cases hampered the actual substitution at the industrial level. Here, past and on-going research on hexaferrites sintering is reviewed with a historical perspective, focusing on the challenges encountered and the solutions explored, and correlating the sintering approaches with the magnetic performance of the resulting ceramic magnet., This work is supported by the European Commission through the H2020 project with Grant agreement H2020-NMBP-2016-720853 (AMPHIBIAN) and by the Spanish Ministerio de Ciencia, Innovación y Universidades (RTI2018-095303-A-C52). C G M acknowledges financial support from Spanish Ministerio de Ciencia e Innovación (MICINN) through the 'Juan de la Cierva' Program (FJC2018-035532-I). Financial support from the Slovenian Research Agency (research core funding No. P2-0087) is acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Efectos del procesamiento cerámico y la adición de nanohilos de FeCo en la obtención de diferentes tipos de imanes permanentes de ferrita más sostenibles y mejorados.

  • Guzmán-Mínguez, J. C.
  • AMPHIBIAN Project ID:720853
La realización de este trabajo ha sido posible gracias a la financiación del Ministerio de Ciencia e Innovación de España a través de los Proyectos no. MAT2017-86450-C4-1-R, MAT2015-64110-C2-1-P, MAT2015-64110-C2-2-P, MAT2017-87072-C4-2-P, RTI2018-095303-B-C51, RTI2018-095303-B-C53, RTI2018-095303-A-C52 y FIS2017-82415-R y a través del Contrato Ramón y Cajal RYC-2017-23320; y por la Comisión Europea a través del Proyecto H2020 nº 720853 (AMPHIBIAN). El trabajo está financiado también por la Comunidad de Madrid a través del Proyecto S2018/NMT-4321 (NANOMAGCOST)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetic domain wall pinning in cobalt ferrite microstructures

  • Ruiz-Gómez, Sandra
  • Mandziak, Anna
  • Martín-García, Laura
  • Prieto, J. E.
  • Prieto, Pilar
  • Munuera, C.
  • Foerster, Michael
  • Quesada, Adrián
  • Aballe, Lucía
  • de la Figuera, Juan
9 pags., 3 figs., A detailed correlative structural, magnetic and chemical analysis of non-stoichiometric cobalt ferrite micrometric crystals was performed by x-ray magnetic circular dichroism combined with photoemission microscopy, low energy electron microscopy, and atomic force microscopy. The vector magnetization at the nanoscale is obtained from magnetic images at different x-ray incidence angles and compared with micromagnetic simulations, revealing the presence of defects which pin the magnetic domain walls. A comparison of different types of defects and the domain walls location suggests that the main source of pinning in these microcrystals are linear structural defects induced in the spinel by the substrate steps underneath the islands., This work is supported by the Grants RTI2018-095303-B-C51,-A- 52, and -B-C53 funded by MCIN/AEI/10.13039/501100011033 and by ‘‘ERDF A way of making Europe’’, and by the Grant S2018-NMT-4321 funded by the Comunidad de Madrid and by ‘‘ERDF A way of making Europe’’. Sandra Ruiz-Gómez gratefully acknowledges the financial support of the Alexander von Humboldt foundation. These experiments were performed at the CIRCE beamline of the ALBA Synchrotron Light Facility, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Growth and characterization of ultrathin cobalt ferrite films on Pt(111)

  • Delgado Soria, Guiomar
  • Freindl, K.
  • Prieto, J. E.
  • Quesada, Adrián
  • de la Figuera, Juan
  • Spiridis, N.
  • Korecki, J.
  • Marco, J.F.
  • AMPHIBIAN Project ID:720853
9 pags., 8 figs., 2 tabs., CoFeO thin films (5 nm and 20 nm thick) were grown by oxygen assisted molecular beam epitaxy on Pt(111) at 523 K and subsequently annealed at 773 K in vacuum or oxygen. They were characterized in-situ using Auger Electron Spectroscopy, Low-Energy Electron Diffraction, Scanning Tunneling Microscopy and Conversion Electron Mössbauer Spectroscopy. The as-grown films were composed of small, nanometric grains. Annealing of the films produced an increase in the grain size and gave rise to magnetic order at room temperature, although with a fraction of the films remaining in the paramagnetic state. Annealing also induced cobalt segregation to the surface of the thicker films. The measured Mössbauer spectra at low temperature were indicative of cobalt ferrite, the both films showing very similar hyperfine patterns. Annealing in oxygen or vacuum affected the cationic distribution, which was closer to that expected for an inverse spinel in the case of annealing in an oxygen atmosphere., This work is supported by the Spanish Ministry of Science and Innovation through Projects RTI2018-095303-B-C51, RTI2018-095303- B-C53, MAT2017-86450-C4-1-R, RTI2018-095303-A-C52, through the Ramón Cajal Contract RYC-2017-23320 and RTI2018-095303-C52 (MCIU/AIE/FEDER,EU), by the Regional Government of Madrid through project S2018-NMT-4321 and by the PROM Programme - International scholarship exchange of Ph.D. students and academics; and by the European Commission through the H2020 Project no. 720853 (AMPHIBIAN), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spinel to disorder rock-salt structural transition on (111) nickel ferrite thin films tailored by Ni content

  • Prieto, P.
  • Serrano Rubio, Aída
  • Rojas-Hernández, Rocío E.
  • Gorgojo, S.
  • Prieto, J. E.
  • Soriano, L.
9 pags., 7 figs., 1 tab., (111)-oriented NiFeO thin films with varying Ni content (0.7 ≤ x ≤ 1.7) have been grown on c-plane (0001) α-AlO substrates by ion beam sputtering. Epitaxial NiFeO thin films with spinel structure are obtained for x ≤ 1. For nickel content exceeding the value of the stoichiometric phase, i.e. NiFeO, a transition from an ordered spinel to a disordered rock-salt phase is identified, being the dominant one when x = 1.7. This result is confirmed by X-ray diffraction, Rutherford backscattering spectroscopy in channeling configuration, Raman spectroscopy, X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS). We also report the first Raman spectra in NiFeO with mainly rock-salt structure. The evolution of the electrical and optical properties of the (111) NiFeO films as Ni content increases, supports the structural change. The electrical resistivity increases up to 10 ohm·cm, the direct and indirect band gaps also increase and only one direct band gap, instead of the two characteristic of the spinel structure, is present in the NiFeO film with x = 1.7., This investigation has been funded by the Comunidad de Madrid through the NANOMAGCOSTCM-P2018/NMT4321 project and by the MINECO of Spain through the RTI2018–095303-A-C52 and RTI2018–095303-A-C51 projects. We acknowledge the support from CMAM for the beam time proposals with codes P00736 and P00684. Part of these experiments were performed at the CLÆSS-BL22 beamline at ALBA Synchrotron (grant number 2020094658). Giulio Gorni is especially grateful for his support during the XAS mea- surements. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395). We also acknowledge the support of Miguel Manso Silván for the optical characterization of the films. The financial support from the Estonian Research Council grants PSG-466 is gratefully acknowledged
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hexaferrite-based permanent magnets with upper magnetic properties by cold sintering process via a non-aqueous solvent

  • Serrano Rubio, Aída
  • García-Martín, Eduardo
  • Granados-Miralles, Cecilia
  • Gorni, Giulio
  • López-Sánchez, Jesús
  • Ruiz-Gómez, Sandra
  • Pérez, Lucas
  • Quesada, Adrián
  • Fernández Lozano, José Francisco
  • AMPHIBIAN Project ID:720853
[EN] The incessant technological pursuit towards a more sustainable and green future depends strongly on permanent magnets. At present, their use is widespread, making it imperative to develop new processing methods that generate highly competitive magnetic properties reducing the fabrication temperatures and costs. Herein, a novel strategy for developing dense sintered magnets based on Sr-hexaferrites with upper functional characteristics is presented. An innovative cold sintering approach using glacial acetic acid as novelty, followed by a post-annealing at 1100 °C, achieves a densification of the ceramic magnets of 92% with respect to the theoretical density and allows controlling the particle growth. After the cold sintering process, a fraction of amorphous SrO is identified, in addition to a partial transformation to α-FeO as secondary crystalline phase. 46 wt% of SrFeO remains, which is mostly recuperated after the post-thermal treatment. These findings do not significantly modify the final structure of ferrite magnets, neither at short- nor long-range order. The innovative process has a positive impact on the magnetic properties, yielding competitive ferrite magnets at lower sintering temperatures with an energy efficiency of at least 25%, which opens up a new horizon in the field of rare-earth free permanent magnets and new possibilities in other applications., This work has been supported by the Ministerio Español de Ciencia, Innovación y Universidades (MCIU) through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52 and The European Commission through the AMPHIBIAN Project (720853). Part of these experiments was performed at the CLÆSS beamline at ALBA Synchrotron with the collaboration of ALBA staff. A.S. acknowledges financial support from Comunidad de Madrid for an “Atracción de Talento Investigador” Contract (2017-t2/IND5395). C.G.-M. and A.Q. acknowledge financial support from Ministerio Español de Ciencia e Innovación (MICINN) through the “Juan de la Cierva” Program (FJC2018-035532-I) and the “Ramón y Cajal” Contract (RYC-2017-035532).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of organic solvent on the cold sintering processing of SrFe12O19 platelet-based permanent magnets

  • Serrano Rubio, Aída
  • García-Martín, Eduardo
  • Granados-Miralles, Cecilia
  • López-Sánchez, Jesús
  • Gorni, Giulio
  • Quesada, Adrián
  • Fernández Lozano, José Francisco
  • AMPHIBIAN Project ID:720853
[EN] In this work we have investigated the effect of the solvent during the processing of SrFeO platelet-based permanent magnets by cold sintering process (CSP) plus a post-thermal treatment. Several organic solvents: glacial acetic acid, oleic acid and oleylamine have been analyzed, optimizing the CSP temperatures at 190−270 °C, under pressures of 375−670 MPa and 6−50 wt% of solvent. Modifications in the morphological and structural properties are identified depending on the solvent, which impacts on the magnetic response. Independently of the solvent, the mechanical integrity of ferrite magnets obtained by CSP is improved by a post-annealing at 1100 °C for 2 h, resulting in relative densities around 92 % with an average grain size of 1 μm and a fraction of SrFeO phase >91 %. H ≥ 2.1 kOe and M of 73 emu/g are obtained in the final sintered ceramic magnets, exhibiting the highest H value of 2.8 kOe for the magnet sintered using glacial acetic acid., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN) through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52, and by the European Commission through Project H2020 No. 720853 (Amphibian). Part of these experiments was performed at the CLAESS beamline at ALBA Synchrotron with the collaboration of ALBA staff. A.S. acknowledges financial support from Comunidad de Madrid for an “Atracción de Talento Investigador” Contract (2017-t2/IND5395). C.G.-M. and A.Q. acknowledge financial support from MICINN through the “Juan de la Cierva” Program (FJC2018-035532-I) and the MICINN through the “Ramón y Cajal” Contract (RYC-2017-23320),, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dense strontium hexaferrite-based permanent magnet composites assisted by cold sintering process

  • García-Martín, Eduardo
  • Granados-Miralles, Cecilia
  • Ruiz-Gómez, Sandra
  • Pérez, Lucas
  • Campo, Ángel Adolfo del
  • Guzmán-Mínguez, J. C.
  • Julián Fernández, César de
  • Quesada, Adrián
  • Fernández Lozano, José Francisco
  • Serrano Rubio, Aída
  • AMPHIBIAN Project ID:720853
[EN] The use of rare-earth-based permanent magnets is one of the critical points for the development of the current technology. On the one hand, industry of the rare-earths is highly polluting due to the negative environmental impact of their extraction and, on the other hand, the sector is potentially dependent on China. Therefore, investigation is required both in the development of rare-earth-free permanent magnets and in sintering processes that enable their greener fabrication with attractive magnetic properties at a more competitive price. This work presents the use of a cold sintering process (CSP) followed by a post-annealing at 1100 °C as a new way to sinter composite permanent magnets based on strontium ferrite (SFO). Composites that incorporate a percentage ≤ 10% of an additional magnetic phase have been prepared and the morphological, structural and magnetic properties have been evaluated after each stage of the process. CSP induces a phase transformation of SFO in the composites, which is partially recovered by the post-thermal treatment improving the relative density to 92% and the magnetic response of the final magnets with a coercivity of up to 3.0 kOe. Control of the magnetic properties is possible through the composition and the grain size in the sintered magnets. These attractive results show the potential of the sintering approach as an alternative to develop modern rare-earth-free composite permanent magnets., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN), Spain, through the projects MAT2017-86540-C4-1-R and RTI2018-095303-A-C52, and by the European Commission through Project H2020 No. 720853 (Amphibian). C.G.-M. and A.Q. acknowledge financial support from MICINN through the “Juan de la Cierva” program (FJC2018-035532-I) and the “Ramón y Cajal” contract (RYC-2017-23320). S. R.-G. gratefully acknowledges the financial support of the Alexander von Humboldt foundation, Germany. A.S. acknowledges the financialsupport from the Comunidad de Madrid, Spain, for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of annealing in the formation of well-crystallized and textured SrFe12O19 films grown by RF magnetron sputtering

  • Delgado Soria, Guiomar
  • Serrano, A.
  • Prieto, J. E.
  • Quesada, Adrián
  • Gorni, Giulio
  • de la Figuera, Juan
  • Marco, J.F.
  • AMPHIBIAN Project ID:720853
10 pags., 7 figs., 4 tabs., We have studied the influence of the annealing treatment on the crystalline growth of SrFe12O19 previously deposited on Si (100) substrates using radio frequency (RF) magnetron sputtering. For this goal, two grown films, with and without ex situ heating step, have been analyzed and compared to determine the differences in their structural, compositional, and magnetic properties. The results obtained by the different analysis techniques, in particular Mössbauer spectroscopy together with EXAFS and XANES data, suggest that the as-grown film is composed of nanocrystalline maghemite nanoparticles and amorphous strontium oxide. Specifically, Mössbauer spectroscopy results pointed out the presence of Fe3+ cations occupying octahedral and tetrahedral sites with hyperfine magnetic fields 49.3 T and 44.2 T, respectively, characteristic of a spinel-related structure. A strontium hexaferrite canonical structure with a c-axis orientation in the sample plane was found for the annealed film. Graphical abstract: [Figure not available: see fulltext.]., This work is supported by the Grants TED2021-130957B-C54, RTI2018-095303-B-C51, -A-C52 and -B-C53 , MAT2017-86450-C4-1-R funded by MCIN/AEI/10.13039/501100011033 by European Union NextGenerationEU/PRTR and by “ERDF A way of making Europe”, by the Grant S2018-NMT-4321 funded by the Comunidad de Madrid and by “ERDF A way of making Europe”, by the Ramon y Cajal Contract RYC-2017-23320 and by the European Commission through the H2020 Project no.720853 (AMPHIBIAN). We gratefully acknowledge the support from CMAM for the beamtime proposal with code STD009/20. Part of these experiments were performed at the CLAESS-BL22 beamline at ALBA Synchrotron and in collaboration with ALBA staf. A.S. acknowledges fnancial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract No. 2017-t2/IND539. We thank Dr S. Cortés for providing access to the Raman spectrometer and for his help in recording these data. Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Size Effects in the Verwey Transition of Nanometer-Thick Micrometer-Wide Magnetite Crystals

  • Campo, Ángel Adolfo del
  • Ruiz-Gómez, Sandra
  • Trapero, E. M.
  • Granados-Miralles, Cecilia
  • Quesada, Adrián
  • Foerster, Michael
  • Aballe, Lucía
  • Prieto, J. E.
  • de la Figuera, Juan
8 pages, 5 figures, 2 tables, We have monitored the Verwey transition in micrometer-wide, nanometer-thick magnetite islands on epitaxial Ru films on Al2O3(0001) using Raman spectroscopy. The islands have been grown by high-temperature oxygen-assisted molecular beam epitaxy. Below 100 K and for thicknesses above 20 nm, the Raman spectra correspond to those observed in bulk crystals and high-quality thin films for the sub-Verwey magnetite structure. At room temperature, the width of the cubic phase modes is similar to the best reported for bulk crystals, indicating a similar strength of electron-phonon interaction. The evolution of the Raman spectra upon cooling suggests that for islands thicker than 20 nm, structural changes appear first at temperatures starting at 150 K while the Verwey transition itself takes place at around 115 K. However, islands thinner than 20 nm show very different Raman spectra, indicating that while a transition takes place, the charge order of the ultrathin islands differs markedly from their thicker counterparts., This work was supported by Grants RTI2018-095303-B-C51, -A-C52, and -B-C53 funded by MCIN/AEI/10.13039/501100011033, by “ERDF A way of making Europe”, by Grant S2018-NMT-4321 funded by the Comunidad de Madrid, and by “ERDF A way of making Europe”. S.R.-G. thanks the Alexander von Humboldt Foundation for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A combined micro-Raman, X-ray absorption and magnetic study to follow the glycerol-assisted growth of epsilon-iron oxide sol-gel coatings

  • López-Sánchez, Jesús
  • Serrano Rubio, Aída
  • Campo, Ángel Adolfo del
  • Muñoz-Noval, A.
  • Salas, Eduardo
  • Cabero, Mariona
  • Varela, María
  • Abuín, Manuel
  • Castro, Germán R.
  • Rubio-Zuazo, J.
  • Rodríguez de la Fuente, Óscar
  • Carmona, N.
[EN] Epsilon iron oxide (ε-FeO) coatings on Si(100) substrates are obtained by an easy one-pot sol-gel recipe assisted by glycerol in an acid medium. Glycerol, given its small dimensions, enables the formation of ε-FeO nanoparticles with a size of a few nanometers and the highest purity is reached in coatings after a densification treatment at 960 °C. The structural and compositional evolution up to 1200 °C is studied by confocal Raman microscopy and X-ray absorption spectroscopy techniques, correlating the existing magnetic properties. We report a novel characterization method, which allows monitoring the evolution of the precursor micelles as well as the intermediate and final phases formed. Furthermore, the inherent industrial technology transfer of the sol-gel process is also demonstrated with the ε-FeO polymorph, impelling its application in the coatings form., This work has been supported by the Ministerio de Ciencia e Innovación (MCINN, Spain) through the projects PIE: 2021-60-E-030, PIE: 2010-6-OE-013, PID2019-104717RB-I00 (2020–2022), MAT2017-86540-C4-1-R, RTI2018-095856-B-C21 (2019–2021), RTI2018-097895-B-C43 and RTI2018-095303-A-C52. The authors are grateful to The ESRF (France), MCINN and Consejo Superior de Investigaciones Científicas (CSIC, Spain) for the provision of synchrotron radiation facilities and to the BM25-SpLine Staff for their valuable help. A.S.and A.M.-N acknowledge financial support from Comunidad de Madrid (Spain) for an “Atracción de Talento Investigador” Contract 2017-t2/IND5395 and 2018-T1/IND-10360, respectively
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Quantifying Li-content for compositional tailoring of lithium ferrite ceramics

  • Granados-Miralles, Cecilia
  • Serrano Rubio, Aída
  • Prieto, P.
  • Guzmán-Mínguez, J. C.
  • Prieto, J. E.
  • Friedel, A. M.
  • García-Martín, Eduardo
  • Fernández, J. F.
  • Quesada, Adrián
9 pags., 6 figs., 3 tabs., Owing to their multiple applications, lithium ferrites are relevant materials for several emerging technologies. For instance, LiFeO2 has been spotted as an alternative cathode material in Li-ion batteries, while LiFe5O8 is the lowest damping ferrite, holding promise in the field of spintronics. The Li-content in lithium ferrites has been shown to greatly affect the physical properties, and in turn, the performance of functional devices based on these materials. Despite this, lithium content is rarely accurately quantified, as a result of the low number of electrons in Li hindering its identification by means of routine materials characterization methods. In the present work, magnetic lithium ferrite powders with Li:Fe ratios of 1:1, 1:3 and 1:5 have been synthesized, successfully obtaining phase-pure materials (LiFeO2 and LiFe5O8), as well as a controlled mixture of both phases. The powders have been compacted and subsequently sintered by thermal treatment (Tmax = 1100 °C) to fabricate dense pellets which preserve the original Li:Fe ratios. Li-content on both powders and pellets has been determined by two independent methods: (i) Rutherford backscattering spectroscopy combined with nuclear reaction analysis and (ii) Rietveld analysis of powder X-ray diffraction data. With good agreement between both techniques, it has been confirmed that the Li:Fe ratios employed in the synthesis are maintained in the sintered ceramics. The same conclusion is drawn from spatially-resolved confocal Raman microscopy experiments on regions of a few microns. Field emission scanning electron microscopy has evidenced the substantial grain growth taking place during the sintering process – mean particle sizes rise from ≈ 600 nm in the powders up to 3.8(6) µm for dense LiFeO2 and 10(2) µm for LiFe5O8 ceramics. Additionally, microstructural analysis has revealed trapped pores inside the grains of the sintered ceramics, suggesting that grain boundary mobility is governed by surface diffusion. Vibrating sample magnetometry on the ceramic samples has confirmed the expected soft ferrimagnetic behavior of LiFe5O8 (with Ms = 61.5(1) Am2/kg) and the paramagnetic character of LiFeO2 at room temperature. A density of 92.7(6)% is measured for the ceramics, ensuring the mechanical integrity required for both their direct utilization in bulk shape and their use as targets for thin-film deposition., This work has been supported by grants RTI2018-095303-B-C51 and RTI2018-095303-A-C52 funded by MCIN/AEI/ 10.13039/501100011033 and by “ERDF A way of making Europe” and grants PID20210124585NB-C31, PID2021–124585NB-C32 and PID2021-124585NB-C33 funded by MCIN/AEI/ 10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”. C.G.-M. acknowledges financial support from grant FJC2018–035532-I funded by MCIN/AEI/ 10.13039/501100011033 and grant RYC2021–031181-I funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGeneration EU/PRTR”. A.S. acknowledges financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract No. 2017-t2/IND5395 and grant RYC2021-031236-I funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”. A.Q. acknowledges financial support from grant RYC-2017023320 funded by MCIN/AEI/ 10.13039/501100011033 and by “ESF Investing in your future”. The authors acknowledge support from CMAM for beamtime proposals with codes STD019/20, STD026/20 and STD033/20., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CoSb3-based skutterudite nanocomposites prepared by cold sintering process with enhanced thermoelectric properties

  • Serrano Rubio, Aída
  • Caballero-Calero, Olga
  • Granados-Miralles, Cecilia
  • Gorni, Giulio
  • Manzano, Cristina V.
  • Rull Bravo, Marta
  • Moure Arroyo, Alberto
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
[EN] We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb-based thermoelectric materials. CSP at 150 °C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %, which is increased to around 92 % after a post-annealing at temperatures ≥ 500 °C in Ar atmosphere. The reported CSP produces Te doped-CoSb nanocomposites with similar morphological and structural characteristics to the starting nanopowders obtained by ball milling in air atmosphere. The post-thermal treatment induces grain coalescence and grain growth, crystallite size growth as well as compositional changes in the nanocomposite, decreasing the amount of the main phase, CoSb, and increasing the weight of secondary phase, CoSb, up to a 30 wt% at 600 °C. Remarkably, the average valence for the Co, Sb and Te absorbing atoms is neither transformed by the sintering process nor by the subsequent heat treatment. The functional response of the sintered thermoelectric nanocomposites exhibits a maximum figure of merit of 0.12(3) at room temperature for the nanocomposites sintered by CSP with a subsequent post-annealing at 500 °C. This is mainly due to its low thermal conductivity in comparison with similar powders sintered by other approaches, and it is explained by the morphological and structural properties. These findings represent an attractive alternative for obtaining efficient thermoelectric skutterudites by a scalable and cost-effective route., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN) through the projects MAT2017-86540-C4-1-R, MAT2017-86540-C4-3-R, RTI2018-095303-A-C52, PID2020-114192RB-C41 and PID2020-118430GB-100. Part of these experiments were performed at the CLAESS-BL22 beamline at ALBA Synchrotron (Grant no. 2020094658) and in collaboration with ALBA staff. A.S. and C.V.M. acknowledge financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” Contract no. 2017-t2/IND5395 and 2019-t1/IND-13541, respectively. C.G.-M. acknowledges financial support from MICINN through the “Juan de la Cierva” program (FJC2018-035532-I). A.M. is indebted to MICINN for the “Ramón y Cajal” contract (RYC-2013-14436), which is co-financed with European Social Fund., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel one-pot sol-gel synthesis route of Fe3C/few-layered graphene core/shell nanoparticles embedded in a carbon matrix

  • Castellano-Soria, Alberto
  • López-Sánchez, Jesús
  • Granados-Miralles, Cecilia
  • Varela, María
  • Navarro, Elena
  • González, César
  • Marín, Pilar
[EN] Fe3C/few-layered graphene core/shell nanoparticles embedded in a carbon matrix are synthesized by a novel two-step surfactant sol-gel strategy, where the processes of hydrolysis, polycondensation and drying take place in a one-pot. The present approach is based on the combined action of oleic acid and oleylamine, which act sterically on the precursor micelles when a densification temperature is performed in a reducing atmosphere. The structural and magnetic evolution of the formed compounds is investigated, ranging from iron oxides such as Fe3O4 and FeO, to the formation of pure Fe3C/C samples from 700 ºC onwards. Interestingly, Fe3C nanoparticles with a size of ~20 nm crystallize immersed in the carbon matrix and the surrounding environment forms an oriented encapsulation built by few-layered graphene. The nanostructures show a saturation magnetization of ~43 emu/g and a moderate coercivity of ~500 Oe. Thereby, an innovative chemical route to produce single phase Fe3C nanoparticles is described, and an effective method of few-layered graphene passivation is proposed, yielding a product with a high magnetic response and high chemical stability against environmental corrosion., Ministerio de Ciencia de Innovación (MCINN), Spain, through the projects: MAT2015–65445-C2–1-R, MAT2017–86450-C4–1-R, MAT2015–67557-C2–1-P, RTI2018–095856-B-C21, RTI2018–095303-A-C52, PIE: 2021-60-E030, PIE: 2010–6-OE-013; and Comunidad de Madrid, Spain, by S2013/MIT-2850 NANOFRONTMAG and S2018/NMT-4321 NANOMAGCOST. The authors are also grateful for the electron microscopy characterization performed in the Centro Nacional de Microscopía Electrónica at the Universidad Complutense de Madrid (ICTS ELECMI, UCM), support from MCINN grant # RTI2018–097895-B-43. C.G.-M. acknowledges the financial support from MICINN through the “Juan de la Cierva” Program (FJC2018–035532-I).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Remanence Increase in SrFe12O19/Fe Exchange-Decoupled Hard-Soft Composite Magnets Owing to Dipolar Interactions

  • Guzmán-Mínguez, J. C.
  • Granados-Miralles, Cecilia
  • Kuntschke, Patrick
  • Julián Fernández, César de
  • Erokhin, Sergey
  • Berkov, Dmitry
  • Schliesch, Thomas
  • Fernández Lozano, José Francisco
  • Quesada, Adrián
  • AMPHIBIAN Project ID:720853
In the search for improved permanent magnets, fueled by the geostrategic and environmental issues associated with rare-earth-based magnets, magnetically hard (high anisotropy)-soft (high magnetization) composite magnets hold promise as alternative magnets that could replace modern permanent magnets, such as rare-earth-based and ceramic magnets, in certain applications. However, so far, the magnetic properties reported for hard-soft composites have been underwhelming. Here, an attempt to further understand the correlation between magnetic and microstructural properties in strontium ferrite-based composites, hard SrFe<sub>12</sub>O<sub>19</sub> (SFO) ceramics with different contents of Fe particles as soft phase, both in powder and in dense injection molded magnets, is presented. In addition, the influence of soft phase particle dimension, in the nano- and micron-sized regimes, on these properties is studied. While Fe and SFO are not exchange-coupled in our magnets, a remanence that is higher than expected is measured. In fact, in composite injection molded anisotropic (magnetically oriented) magnets, remanence is improved by 2.4% with respect to a pure ferrite identical magnet. The analysis of the experimental results in combination with micromagnetic simulations allows us to establish that the type of interaction between hard and soft phases is of a dipolar nature, and is responsible for the alignment of a fraction of the soft spins with the magnetization of the hard. The mechanism unraveled in this work has implications for the development of novel hard-soft permanent magnets., This work was supported by the European Commission through Project H2020 No. 720853 (AMPHIBIAN). It is also supported by the Spanish Ministry of Science and Innovation through Grants RTI2018-095303-BC51, RTI2018-095303-A-C52, PID2021-124585NB-C33, TED2021-130957B-C51 funded by MCIN/AEI/10.13039/501100011033, by “ERDF A way of making Europe” and by the “European Union NextGenerationEU/PRTR”. Financed by the European Union—NextGenerationEU (National Sustainable Mobility Center CN00000023, Italian Ministry of University and Research Decree n. 1033—17/06/2022, Spoke 11—Innovative Materials and Lightweighting). C.G.-M. acknowledges financial support from grant RYC2021-031181-I funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”. A.Q. acknowledges financial support from MICINN through the Ramón y Cajal Program (RYC-2017-23320)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sol-gel synthesis control of iron-cobalt alloy/ferrite core/shell nanoparticles supported by a carbon medium with semi-hard magnetic features

  • Castellano-Soria, Alberto
  • López-Sánchez, Jesús
  • Serrano Rubio, Aída
  • Gorni, Giulio
  • Varela, María
  • Sardinero, Ignacio
  • Carmona, N.
  • Hernando, Antonio
  • Marín, Pilar
  • Navarro, Elena
12 pags., 7 figs., 3 tabs., We explore a simple and optimized approach for obtaining magnetic nanoparticle-carbon composites by a novel one-pot sol-gel method. In them, various metal cations ratios of Fe3+ and Co2+ are evaluated. The ratio of Fe:Co is a critical parameter that governs the presence of different crystalline phases with tailored magnetic properties. Interestingly, the smallest introduction of Co into the synthesis (19Fe:1Co) provides an abrupt emergence of the body-centered cubic (bcc) Fe-Co alloy, instead of the orthorhombic Pnma structure characteristic of the Fe3C intermetallic compound (1Fe:0Co). Advanced structural and electronic characterizations reveal the formation of Fe-Co/Co-ferrite core/shell nanoparticle structures embedded in a carbon matrix. The sphere-like nanoparticles range from 10 to 45 nm and the shells show a spinel structure with a thickness of 2–3 nm. In addition, X-ray absorption spectroscopy unveils that the oxidation state of Fe and Co cations is close to zero, demonstrating their predominant metallic character. The magnetic properties can be modulated by a precise control of the alloy composition varying the Co content, displaying saturation magnetization values close to ∼137 emu/g. The nanoparticles are mainly single magnetic domain with a considerable coercive field (∼450 Oe), higher than those reported in the literature for Fe-Co nanoparticles. This semi-hard character is due to a notable spring exchange effect emerged by passivating the surface of Fe-Co-bcc cores with a thin Co-ferrite-like shell., The work has been supported by the Ministerio de Ciencia e Innovación (MCINN) through the projects MAT2015-65445-C2-1-R, MAT2017-86450-C4-1-R, MAT2015-67557-C2-1-P, RTI2018–095856-B-C21, RTI2018–095303-A-C52, PIE: 2021-60-E-030, PIE: 2010-6-OE-013, PID2021-122980OB-C51 and Comunidad de Madrid by S2013/MIT-2850 NANOFRONTMAG and S2018/NMT-4321 NANOMAGCOST. Electron microscopy measurements were carried out at the Centro Nacional de Microscopía Electrónica at the Universidad Complutense de Madrid (ICTS ELECMI, UCM). The authors are grateful to The ESRF (France), MCINN and Consejo Superior de Investigations Científicas (CSIC, Spain) for the provision of synchrotron radiation facilities and to the BM25-SpLine Staff for their support. XAS experiments were also performed at the CLAESS-BL22 beamline at ALBA Synchrotron (Grant no. 2022025654) in collaboration with ALBA staff. Giulio Gorni acknowledges financial support from FJC2020–044866-I /MCIN/AEI/ 10.13039/501100011033 and European Union “NextGenerationEU”/PRTR”. A.S. acknowledges financial support from the “Ayudas para contratos Ramón y Cajal” contract No. RYC2021-031236-I., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Non-monotonic magnetic anisotropy behavior as a function of adsorbate coverage in Fe ultrathin films near the spin reorientation transition

  • Quesada, Adrián
  • Chen, Gong
  • N'Diaye, A. T.
  • Wang, P.
  • Wu, Y.Z.
  • Schmid, Andreas K.
  • AMPHIBIAN Project ID:720853
[EN] Carbon monoxide (CO) adsorption on ultrathin fcc Fe films is known to result in the rotation of magnetization from out-of-plane to in-plane. By imaging in real time the magnetic domain structure of perpendicularly magnetized Fe/(2 ML)Ni/Cu(100) films during exposure to CO, we demonstrate that the effect of adsorption on the magnetic properties occurs in two distinct stages. Initially, when CO bonds preferentially on bridge sites, perpendicular magnetic anisotropy is enhanced. Later, when on-top adsorption dominates, magnetization rotates towards in-plane in agreement with previous studies. This CO-induced spin reorientation transition (SRT) is not reversible by annealing, as CO desorption would require high temperature cycles which yield permanent structural changes in the metal films. This study demonstrates the existence of a novel non-monotonic behavior of the magnetic anisotropy as a function of adsorbate coverage. The influence of CO on ultrathin film magnetism in real time near critical points, where the anisotropy balance is extremely sensitive to small variations, reveals the previously elusive complexity of this adsorbate induced SRT., Financial support from the Spanish Ministerio de Ciencia e Innovación through Proj. No. RTI2018-095303-A-C52 and the ‘‘Ramón yCajal’’ Program (RYC-2017-23320); and from the EuropeanCommission through project AMPHIBIAN H2020-NMBP-2016- AMPHIBIAN (no. 720853). Y. Z. W. acknowledges financial support by National Natural Science Foundation of China (Grants No. 11734006 and No. 11974079), and Shanghai Municipal Science and Technology Major Project (Grant No.2019SHZDZX01), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Generation of Defective Few-Layered Graphene Mesostructures by High-Energy Ball Milling and Their Combination with FeSiCuNbB Microwires for Reinforcing Microwave Absorbing Properties

  • López-Sánchez, Jesús
  • Peña, Álvaro
  • Serrano, Aída
  • Del Campo, Adolfo
  • Rodríguez de la Fuente, Óscar
  • Carmona, N.
  • Matatagui, Daniel
  • Horrillo, Carmen
  • Rubio-Zuazo, J.
  • Navarro, Elena
  • Marín, Pilar
15 páginas, 9 figuras, 4 tablas, Defective few-layered graphene mesostructures (DFLGMs) are produced from graphite flakes by high-energy milling processes. We obtain an accurate control of the generated mesostructures, as well as of the amount and classification of the structural defects formed, providing a functional material for microwave absorption purposes. Working under far-field conditions, competitive values of minimum reflection loss coefficient (RLmin) = ¿21.76 dB and EAB = 4.77 dB are achieved when DFLGMs are immersed in paints at a low volume fraction (1.95%). One step forward is developed by combining them with the excellent absorption behavior that offers amorphous Fe73.5Si13.5B9Cu1Nb microwires (MWs), varying their filling contents, which are below 3%. We obtain a RLmin improvement of 47% (¿53.08 dB) and an EAB enhancement of 137% (4 dB) compared to those obtained by MW-based paints. Furthermore, a fmin tunability is demonstrated, maintaining similar RLmin and EAB values, irrespective of an ideal matching thickness. In this scenario, the Maxwell-Garnet standard model is valid, and dielectric losses mainly come from multiple reflections, interfacial and dielectric polarizations, which greatly boost the microwave attenuation of MWs. The present concept can remarkably enhance not only the MW attenuation but can also apply to other microwave absorption architectures of technological interest by adding low quantities of DFLGMs., The present work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN) through the projects: PIE-2010-OE-013-200014, PIE 2021-60-E-030, RTI2018-095856-B-C21, and RTI2018-095303-A-C52; Ministerio de Asuntos Económicos y Transformación Digital (MINECO) by PID2020-114192RB-C41; and Comunidad de Madrid, Spain, by S2018/NMT-4321 NANOMAGCOST. MICINN also supports A.S., D.M., and A.P. through the grants RYC2021-031236-I, RYC2021-031166-I, and PRE2019-0875001234, respectively, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly textured zinc aluminate: Nd, Ce films over sapphire for NIR emitting applications

  • Rojas-Hernández, Rocío E.
  • Rubio Marcos, Fernando
  • Serrano Rubio, Aída
  • Román-Sánchez, Sara
  • Fernández Lozano, José Francisco
  • Hussainova, Irina
[EN] The development of sapphire-compatible optical sources is highly valued due to the potential cost-effective applications in sapphire-based integrated devices. In this work, a screen printing technique assisted by a molten salt flux was used to synthesize (hk0)-textured ZnAl2O4: Nd, Ce sub-micron films deposited over the sapphire substrate. The study is focused at controlling Ce concentration in the emitting layers, as well as determining the key parameters to be met for the development of ZnAl2O4-based films of high efficiency and remarkable optical properties. A degree of crystallinity of the ZnAl2O4-based films, and a precise adjustment of texture are the keys parameters for further improvement of NIR luminescence efficiency. Specifically, (hk0)- textured films were developed at sintering temperature of around 1300 ◦C, which contributed to a higher NIR emission intensity as compared to that of (hkl)-untextured films. Therefore, the design process carried out in this work promotes a feasible way to achieve a high NIR emission performance, demonstrating the validity of the approach for a wide range of applications., The financial support from the Estonian Research Council (grants PSG-466, PRG-643) is gratefully acknowledged. F. Rubio-Marcos is indebted to MINECO (Spanish Government) project PID2020- 114192RB-C41 and acknowledges financial support from Comunidad de Madrid for the “Doctorados Industriales” project (IND2020/IND- 17375), which is co-financed by the European Social Fund. Part of these experiments was performed at the CLAESS beamline at ALBA Synchrotron during the execution of an awarded Beamtime. A.S. acknowledges financial support from the Comunidad de Madrid for an “Atracci´on de Talento Investigador” contract No. 2017-t2/IND5395 and to MINECO through the project RTI2018-095303-A-C52., Supplementary data to this article can be found online at https://doi. org/10.1016/j.ceramint.2022.12.190, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modulating the magnetic properties of Fe3C/C encapsulated core/shell nanoparticles for potential prospects in biomedicine

  • Castellano-Soria, A.
  • López-Méndez, R.
  • Espinosa, A.
  • Granados-Miralles, Cecilia
  • Varela, M.
  • Marín, P.
  • Navarro, E.
  • López-Sánchez, Jesús
In the pursuit of alternative and less invasive medical treatments, magnetic nanoparticles (NPs) have gained significant relevance. Iron carbides NPs stand out for their higher saturation magnetizations compared to iron oxides, while maintaining a suitable biocompatibility. In this work, high control is achieved over the composition and morphology of Fe3C/C encapsulated core/shell nanoparticles through fine-tuning of the sol-gel synthesis parameters. Specifically, the impact of decreasing each surfactant concentration added, nt, the same both for oleylamine (ON) and oleic acid (OA), has been explored. A minimum value for such parameter denoted by nt,min. was required to produce pure Fe3C@C NP-composites. For nt < 4 mmol, some minor α-Fe impurities arise, and the effective carburization becomes unstable due to insufficient carbon. The magnetic properties of the materials prepared were optimized by reducing the excess carbon from surfactants, resulting in saturation magnetization values of 86 emu/g. (for pure Fe3C at nt = 5 mmol) and 102 emu/g (for Fe3C and <2 % w.t. of α-Fe impurity at nt = 4 mmol). In view of this, several cytotoxicity studies for different Fe3C@C samples were conducted, exhibiting excellent biocompatibility in cell-based assays, which could lead to potential application at the forefront of biomedical fields. © 2024 The Authors, The work has been supported by the Ministerio de Ciencia e Innovacion (MCINN) through the projects PDC2022-133039-I00, PID2021-123112OB-C21-MICIIN, TED2021-129688B-C21, MAT2015-65445-C2-1-R, MAT2017-86450-C4-1-R, MAT2015-67557-C2-1-P, RTI2018-095856-B-C21, RTI2018-095303-A-C52, PID2020-114192RB-C41, PIE: 2021-60-E-030, PIE: 2010-6-OE-013, PID2021-122980OB-C51, FPI PRE2020-96246 grant (R.L-M.), and Comunidad de Madrid by NANOMAGCOST-CM, S2013/MIT-2850 NANOFRONTMAG, (MAD2D-CM)-UCM3, S2018/NMT-4321 NANOMAGCOST, 2018-T1/IND-1005 (A.E.) and S2022/BMD-7434 ASAP-CM. C.G.-M. acknowledges financial support from grant RYC2021-031181-I funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". J. L.-S. acknowledges the financial support from Spanish Ministry of Economic Affairs and Digital Transformation through the project PID2021-122980OB-C5 and from grant RYC2022-035912-I funded by MCIU/AEI/10.13039/501100011033 and by the European Social Fund Plus (ESF+). Electron microscopy measurements were carried out at the Centro Nacional de Microscopia Electronica at the Universidad Complutense de Madrid (ICTS ELECMI, UCM). The authors also acknowledge the BM25-SpLine Staff for their valuable help and the provision of the beamline under the projects A25-2-1053 and A25-2-1009., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Finite element modeling of plasmonic resonances in photothermal gold nanoparticles embedded in cells

  • París Ogáyar, Marina
  • López-Méndez, R.
  • Figueruelo-Campanero, Ignacio
  • Muñoz-Ortiz, T.
  • Wilhelm, C.
  • Jaque, D.
  • Espinosa, Ana
  • Serrano Rubio, Aída
The use of plasmonic nanoparticles in performing photothermal treatments in cancer cells requires a full knowledge about their optical properties. The surface plasmon resonance is easily foreseen and measurable in colloidal suspensions, however it can be strongly modified when located inside cells. Assessing the optical behavior of plasmonic nanoparticles in cells is essential for an efficient and controlled treatment. This requires the combination of experimental data and computational models to understand the mechanisms that cause the change in their optical response. In this work, we investigate the plasmonic response of Au nanospheres (AuNSs) internalized into cancer cells (MCF-7). Experimental data are compared to the simulations provided by a 3D model based on a finite element method. We demonstrate the impact of physical parameters such as the type of NS assembly, the surrounding medium and the interparticle gap, in the photothermal efficiency of AuNSs. Results open the avenue to predict, by numerical calculations, the optical properties of plasmonic nanoparticles inside cells to minimize treatment costs and times in photothermal therapies. © 2024 RSC., This work has been supported by the Ministerio Español de Ciencia e Innovaci´on (MICINN) through the projects PID2021- 124585NB-C33, PID2021-127033OB-C21, RTI2018-095303-AC52 and CNS2023-144689 funded by MCIN/AEI/10.13039/ 501100011033 and by “ERDF A way of making Europe”. M. P. O., R. L. M., and I. F.-C. acknowledge the nancial support from MICINN for an FPU (FPU20/03166) and FPI (PRE2020- 96246 and PRE2020-092625) contracts, respectively. A. E. also acknowledges the nancial support from MICINN for a Ram´on y Cajal contract (RYC2020-029282-I), Comunidad de Madrid (2018-T1/IND-1005 and ASAP-CM S2022/BMD-7434) and CSIC (PIE-20226AT024). A. S. acknowledges nancial support from grant RYC2021-031236-I funded by MCIN/AEI/ 10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR” and CSIC (PIE-20236AT002). IMDEA Nanociencia acknowledges the “Severo Ochoa” program for Centres of Excellence in R&D (CEX2020-001039-S). We thank Milagros Guerra for her assistance with TEM preparation at the Electron Microscopy Service of the Centro de Biolog´ıa Molecular Severo Ochoa (CBMSO, CSIC-UAM Spain), as well as to technical personnel at ICMM-CSIC (Spain) for conducting ICP-OES measurements., Supporting Information, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

In situ thermal runaway of Si-based press-fit diodes monitored by infrared thermography

  • Moure Arroyo, Alberto
  • Román-Sánchez, Sara
  • Serrano Rubio, Aída
  • Lorite, Israel
  • Fernández Lozano, José Francisco
Overvoltage is one of the main causes that lead to the failure of electronic devices. This makes fundamental to understand the electrical and thermal mechanisms engaged in the process. In this work, the influence of the semiconductor technology on the thermal runaway involved in the dielectric breakdown of commercial press-fit diodes, operating in reverse conditions, has been studied. Infrared thermography has been used to monitor the temperature evolution before, during and after the failure. Schottky and Metal oxide semiconductor devices, based on Si, have been evaluated following this methodology. The current flowing through the diode causes its temperature to rise, which increases the current with a further increase in temperature that triggers the avalanche process. The diode configuration conditions the heating associated with the spark appearing during the breakdown. This process is faster for Schottky diodes than for Metal oxide semiconductors, leading to higher temperatures. Besides, mechanical breaking is observed in the semiconductor due to the stresses generated during the fast heating-cooling processes after the different breakdowns events. The reached temperatures are enough to melt the solder that creates an electrical path, which short-circuits the diodes and leads to their final failure. These differences in the failure behavior must be taken into account to choose the adequate technology in practical applications. © 2020 Elsevier B.V., All rights reserved., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) under the project MAT2017-86450-C4-1-R and RTI2018-095303-A-C52. Dr. Alberto Moure is indebted to MINECO for a ‘Ramon y Cajal’ contract (ref: RYC-2013-14436), which is co-financed by the European Social Fund. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395). The authors acknowledge to Marta Furio for the CT-scan measurements at the “Museo Nacional de Ciencias Naturales”., Appendix A. Supplementary data at DOI: https://doi.org/10.1016/j.rinp.2020.103529, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the design on the thermal response of press-fit diodes: An infrared thermographic study

  • Moure Arroyo, Alberto
  • Serrano Rubio, Aída
  • Román-Sánchez, Sara
  • Lorite, Israel
  • Fernández Lozano, José Francisco
A critical effect in the field of the power semiconductors is their heating processes under high currents regime, in the order of amperes. The thermal characterization in working conditions is not always an easy task, and its over/underestimation can lead to failures in the design of the devices. Infrared thermography measurements are shown in this work as a valuable tool to determine the temperature mapping, profiles and heating and cooling rates of diodes under working conditions. Press-fit metal-oxide semiconductors commercial diodes with different designs from two different suppliers have been analyzed. This work provides elements that relate the dissipated power and the release of heat with the design. © 2021 Elsevier B.V., All rights reserved., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) under the project MAT2017-86450-C4-1-R and RTI2018-095303-A-C52. Dr. Alberto Moure is indebted to MINECO for a ‘Ramon y Cajal’ contract (ref: RYC-2013-14436), which is co-financed by the European Social Fund. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal response of active Si in press-fit rectifier diodes by confocal Raman microscopy: Influence of diode design and technology

  • Román-Sánchez, Sara
  • Serrano Rubio, Aída
  • Campo, Ángel Adolfo del
  • Lorite, Israel
  • Fernández Lozano, José Francisco
  • Moure Arroyo, Alberto
Overheating resulting from the circulation of high electric currents (in the order of tens of amperes) that some electronic devices undergo when they are in operation, can induce structural modifications such as mechanical stresses that could reduce their lifetime. In order to optimize their performance, understanding the phenomenology that takes place in devices at high-temperature regimen induced under operating conditions is fundamental. In this work, the thermal behavior of the Si-based semiconductor part of several press-fit rectifier diodes with different design and technology (Schottky, Metal Oxide Semiconductor and PN junction) has been studied by Confocal Raman Microscopy. The experiments have been performed on two specific functional parts of the active Si chip (i.e., near and far from the Si/electrode interface), discerning non-thermal effects such as stress and doping from the purely thermal ones with a specific analysis procedure of the Si T2g Raman active mode. This methodology enables an advance, non-destructive and located characterization of the thermal response of the diodes, which will help to optimize the performance of electronic devices and extend their useful life and reliability by avoiding or, at least, minimizing the damage caused by the temperature excess. © 2022 Elsevier B.V., All rights reserved., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) under the project RTI2018-095303-A-C52 and PID2020-114192RB-C41. S.R.-S. acknowledges the financial support from FARDIO project to SEG Automotive Germany GmbH. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395). Dr. A.M. is indebted to MINECO for a ‘Ramon y Cajal’ contract (ref: RYC-2013-14436), which is co-financed by the European Social Fund., Appendix A. Supplementary data The following is/are the supplementary data to this article DOI: https://doi.org/10.1016/j.jmrt.2022.03.116, Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

Boosting the tunable microwave scattering signature of sensing array platforms consisting of amorphous ferromagnetic Fe_2.25Co_72.75Si_10B_15 microwires and its amplification by intercalating cu microwires

  • Archilla Sanz, Diego
  • López Sánchez, Jesús
  • Hernando Grande, Antonio
  • Navarro Palma, Elena
  • Marín Palacios, María Pilar
The following work addresses new configurations of sensing array platforms that are composed of Co-based amorphous ferromagnetic microwires (MWs) to obtain an enhanced modulation of the microwave scattering effects through the application of low strength DC or AC magnetic fields. An amorphous MW is an ultrasoft ferromagnetic material (coercivity similar to 0.2 Oe) with a circumferential magnetic anisotropy that provides a high surface sensitivity when it is subjected to an external magnetic field. Firstly, microwave scattering experiments are performed as a function of the length and number of MWs placed parallel to each other forming an array. Subsequently, three array configurations are designed, achieving high S_21 scattering coefficients up to about -50 dB. The influence of DC and AC magnetic fields on S_21 has been analyzed in frequency and time domains representation, respectively. In addition, the MWs sensing array has been overlapped by polymeric surfaces and the variations of their micrometric thicknesses also cause strong changes in the S_21 amplitude with displacements in the frequency that are associated to the maximum scattering behavior. Finally, a new concept for amplifying microwave scattering is provided by intercalating Cu MWs into the linear Co-based arrays. The designed mixed system that is composed by Co-based and Cu MWs exhibits a higher S_21 coefficient when compared to a single Co-based MW system because of higher electrical conductivity of Cu. However, the ability to modulate the resulting electromagnetic scattering is conferred by the giant magneto-impedance (GMI) effects coming from properties of the ultrasoft amorphous MWs. The mixed array platform covers a wide range of sensor applications, demonstrating the feasibility of tuning the S_21 amplitude over a wide scattering range by applying AC or DC magnetic fields and tuning the resonant frequency position according to the polymeric slab thickness.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Sol-gel synthesis control of iron-cobalt alloy/ferrite core/shell nanoparticles supported by a carbon medium with semi-hard magnetic features

  • Castellano Soria, Alberto
  • López Sánchez, Jesús
  • Serrano, Aida
  • Gorni, Giulio
  • Varela Del Arco, María
  • Sardinero, Ignacio
  • Carmona Tejero, Noemí
  • Hernando Grande, Antonio
  • Marín Palacios, María Pilar
  • Navarro Palma, Elena
We explore a simple and optimized approach for obtaining magnetic nanoparticle-carbon composites by a novel one-pot sol-gel method. In them, various metal cations ratios of Fe3+ and Co2+ are evaluated. The ratio of Fe:Co is a critical parameter that governs the presence of different crystalline phases with tailored magnetic properties. Interestingly, the smallest introduction of Co into the synthesis (19Fe:1Co) provides an abrupt emergence of the body-centered cubic (bcc) Fe-Co alloy, instead of the orthorhombic Pnma structure characteristic of the Fe3C intermetallic compound (1Fe:0Co). Advanced structural and electronic characterizations reveal the formation of Fe-Co/Co-ferrite core/shell nanoparticle structures embedded in a carbon matrix. The sphere-like nanoparticles range from 10 to 45 nm and the shells show a spinel structure with a thickness of 2–3 nm. In addition, X-ray absorption spectroscopy unveils that the oxidation state of Fe and Co cations is close to zero, demonstrating their predominant metallic character. The magnetic properties can be modulated by a precise control of the alloy composition varying the Co content, displaying saturation magnetization values close to ∼137 emu/g. The nanoparticles are mainly single magnetic domain with a considerable coercive field (∼450 Oe), higher than those reported in the literature for Fe-Co nanoparticles. This semi-hard character is due to a notable spring exchange effect emerged by passivating the surface of Fe-Co-bcc cores with a thin Co-ferrite-like shell
Docta Complutense
Publicación Artículo científico (JournalArticle)

A feasible pathway to stabilize monoclinic and tetragonal phase coexistence in barium titanate-based ceramics

  • Necib, Jallouli
  • López Sánchez, Jesús
  • Rubio Marcos, Fernando
  • Serrano, Aída
  • Navarro Palma, Elena
  • Peña Moreno, Álvaro
  • Taoufik, Mnasri
  • Smari, Mourad
  • Rojas Hernández, Rocío Estefanía
  • Carmona Tejero, Noemí
  • Marín Palacios, María Pilar
Multiphase coexistence has attracted significant interest in recent years because its control has entailed a significant breakthrough for the piezoelectric activity enhancement of lead-free piezoelectric oxides. However, the comprehension of phase coexistence still has many controversies including an adequate synthesis process and/or the role played by crystalline phases in functional properties. In this study, functional barium titanate [BaTiO_(3), (BTO)]-based materials with tunable functional properties were obtained by compositional modification via Bismuth (Bi) doping. Towards this aim, we systematically synthesized BTO-based materials by a sol-gel method, focusing on the control of Bi substitution in the BaTiO_(3) structure. In particular, we found that the substitution of Bi^(+3) leads to the stabilization of a monoclinic-tetragonal (M-T) phase boundary close to room temperature, which facilities the polarization process of the system. As a surprising result, we believe that the simple and cost-effective strategy and design principles described in this work open up the possibility of obtaining BTO-based lead-free ceramics with enhanced properties induced by the stabilization of the phase coexistence, expanding their application range.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Ferrimagnetic clusters as the origin of anomalous Curie-Weiss behavior in ZnFe_2O_4 antiferromagnetic susceptibility

  • Hernando Grande, Antonio
  • Cobos Fernández, Miguel Ángel
  • Jiménez, José Antonio
  • Llorente, Irene
  • García Escorial, Asunción
  • Presa Muñoz De Toro, Patricia Marcela De La
Different studies carried out in the last three decades on the magnetic susceptibility of the spinel ZnFe_2O_4 ferrite have revealed the positive character of its Curie-Weiss temperature, contradicting its observed antiferromagnetic behavior which is characterized by a well-defined susceptibility peak centered around the Neel temperature (10 K). Some approaches based on ab initio calculations and mixture of interactions have been attempted to explain this anomaly. This work shows how for very low values of the inversion parameter, the small percentage of Fe atoms located in tetrahedral sites gives rise to the appearance of ferrimagnetic clusters around them. Superparamagnetism of these clusters is the main cause of the anomalous Curie-Weiss behavior. This finding is supported experimentally from the thermal dependence of the inverse susceptibility and its evolution with the degree of inversion.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Control of the length of Fe73.5Si13.5Nb3CU1B9 microwires to be used for magnetic and microwave absorbing purposes

  • Birame Gueye, Papa Gorgui
  • López Sánchez, Jesús
  • Navarro Palma, Elena
  • Serrano, Aída
  • Marín Palacios, María Pilar
A combination of high-energy ball milling, vacuum filtering, and sedimentation processes has been demonstrated to be a useful approach to reduce, in a controlled way, the length of as-cast Fe_(73.5)Si_(13.5)Nb_3Cu_1B_9 amorphous magnetic microwires (MWs) and annealed material at 550 degrees C in nitrogen conditions. Homogeneous compositional microstructures with fairly narrow size distributions between 1300 and 11.7 mu m are achieved, exhibiting tunable response as a soft magnetic material and as a microwave absorber. From the magnetic perspective, the soft magnetic character is increased with smaller length of the MWs, whereas the remanence has the opposite behavior mainly due to the structural defects and the loss of the shape anisotropy. From the microwave absorption perspective, a novel potential applicability is tested in these refined microstructures. This innovation consists of coatings based on commercial paints with a filling percentage of 0.55% of MWs with different lengths deposited on metallic sheets. Large attenuation values around -40 dB are obtained in narrow spectral windows located in the GHz range, and their position can be varied by combining different optimized lengths of MW. As an example of this powerful mechanism for absorbing microwaves at specific frequencies, MW lengths of 2 mm and 50 mu m are chosen, where precise tailoring of the minimum reflection loss (R_L)is obtained in a range between 8.85 and 13.25 GHz. To confirm these experimental results, an effective medium standard model proposed for electrical permittivity is used. Experimental and theoretical results are consistent and these novel composites are also proposed as a feasible candidate for designing frequency-selective microwave absorbers on demand, with low filling percentages and high absorption intensity values.