Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 19
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Tailoring the Lithium Concentration in Thin Lithium Ferrite Films Obtained by Dual Ion Beam Sputtering

  • Prieto Recio, Pilar|||0000-0001-8978-5139
  • Hernández-Gómez, Cayetano
  • Román-Sánchez, Sara
  • París Ogáyar, Marina|||0000-0002-4816-7729
  • Gorni, Giulio
  • Prieto, José Emilio|||0000-0003-2092-6364
  • Serrano, Aida|||0000-0002-6162-0014
Thin films of lithium spinel ferrite, LiFeO, have attracted much scientific attention because of their potential for efficient excitation, the manipulation and propagation of spin currents due to their insulating character, high-saturation magnetization, and Curie temperature, as well as their ultra-low damping value. In addition, LiFeO is currently one of the most interesting materials in terms of developing spintronic devices based on the ionic control of magnetism, for which it is crucial to control the lithium's atomic content. In this work, we demonstrate that dual ion beam sputtering is a suitable technique to tailor the lithium content of thin films of lithium ferrite (LFO) by using the different energies of the assisting ion beam formed by Ar + and O + ions during the growth process. Without assistance, a disordered rock-salt LFO phase (i.e., LiFeO) can be identified as the principal phase. Under beam assistance, highly out-of-plane-oriented (111) thin LFO films have been obtained on (0001) AlO substrates with a disordered spinel structure as the main phase and with lithium concentrations higher and lower than the stoichiometric spinel phase, i.e., LiFeO. After post-annealing of the films at 1025 K, a highly ordered ferromagnetic spinel LFO phase was found when the lithium concentration was higher than the stoichiometric value. With lower lithium contents, the antiferromagnetic hematite (α-FeO) phase emerged and coexisted in films with the ferromagnetic LiFeO. These results open up the possibility of controlling the properties of thin lithium ferrite-based films to enable their use in advanced spintronic devices.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of annealing in the formation of well-crystallized and textured SrFe12O19 films grown by RF magnetron sputtering

  • Delgado Soria, Guiomar
  • Serrano, A.
  • Prieto, J. E.
  • Quesada, Adrián
  • Gorni, Giulio
  • de la Figuera, Juan
  • Marco, J.F.
  • AMPHIBIAN Project ID:720853
10 pags., 7 figs., 4 tabs., We have studied the influence of the annealing treatment on the crystalline growth of SrFe12O19 previously deposited on Si (100) substrates using radio frequency (RF) magnetron sputtering. For this goal, two grown films, with and without ex situ heating step, have been analyzed and compared to determine the differences in their structural, compositional, and magnetic properties. The results obtained by the different analysis techniques, in particular Mössbauer spectroscopy together with EXAFS and XANES data, suggest that the as-grown film is composed of nanocrystalline maghemite nanoparticles and amorphous strontium oxide. Specifically, Mössbauer spectroscopy results pointed out the presence of Fe3+ cations occupying octahedral and tetrahedral sites with hyperfine magnetic fields 49.3 T and 44.2 T, respectively, characteristic of a spinel-related structure. A strontium hexaferrite canonical structure with a c-axis orientation in the sample plane was found for the annealed film. Graphical abstract: [Figure not available: see fulltext.]., This work is supported by the Grants TED2021-130957B-C54, RTI2018-095303-B-C51, -A-C52 and -B-C53 , MAT2017-86450-C4-1-R funded by MCIN/AEI/10.13039/501100011033 by European Union NextGenerationEU/PRTR and by “ERDF A way of making Europe”, by the Grant S2018-NMT-4321 funded by the Comunidad de Madrid and by “ERDF A way of making Europe”, by the Ramon y Cajal Contract RYC-2017-23320 and by the European Commission through the H2020 Project no.720853 (AMPHIBIAN). We gratefully acknowledge the support from CMAM for the beamtime proposal with code STD009/20. Part of these experiments were performed at the CLAESS-BL22 beamline at ALBA Synchrotron and in collaboration with ALBA staf. A.S. acknowledges fnancial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract No. 2017-t2/IND539. We thank Dr S. Cortés for providing access to the Raman spectrometer and for his help in recording these data. Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A Platform for Addressing Individual Magnetite Islands Grown Epitaxially on Ru(0001) and Manipulating Their Magnetic Domains

  • Ruiz-Gómez, Sandra
  • Trapero, E. M.
  • Fernández-González, Claudia
  • Campo, Ángel Adolfo del
  • Granados-Miralles, Cecilia
  • Prieto, J. E.
  • Khaliq, Muhammad W.
  • Niño, Miguel Ángel
  • Foerster, M.
  • Aballe, Lucía
  • de la Figuera, Juan
[EN] We have grown high-quality magnetite micrometric islands on ruthenium stripes on sapphire through a combination of magnetron sputtering (Ru film), high-temperature molecular beam epitaxy (oxide islands), and optical lithography. The samples have been characterized by atomic force microscopy, Raman spectroscopy, X-ray absorption and magnetic circular dichroism in a photoemission microscope. The magnetic domains on the magnetite islands can be modified by the application of current pulses through the Ru stripes in combination with magnetic fields. The modification of the magnetic domains is explained by the Oersted field generated by the electrical current flowing through the stripes underneath the magnetite nanostructures. The fabrication method is applicable to a wide variety of rock salt and spinel oxides., Grants PID2021-124585NB-C31; RTI2018-095303-B-C51; RTI2018-095303-B-C53; TED2021-130957B-C54 fundedby MCIN/AEI/10.13039/501100011033,by “ERDFA wayof making Europe”,by the”European Union Next GenerationEU/PRTR”,an by theGrantS 2018-NMT-4321fundedby the Comunidad de Madrid and by “ERDFA wayof making Europe”.RYC2021-031181-I funded by MCIN/AEI/10.13039/501100011033 and by the“European Union Next Generation EU/PRTR”, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Ni substitution on the antiferromagnetic domains of cobalt oxide

  • Mandziak, Anna
  • de la Figuera, Juan
  • Quesada, Adrián
  • Berja, Alba
  • Granados-Miralles, Cecilia
  • Prieto, J. E.
  • Aballe, Lucía
  • Foerster, Michael
  • Niño, Miguel Ángel
  • Nita, Pawel
9 pags., 8 figs., We present a spatially resolved X-ray magnetic linear dichroism study of high quality micron-sized mixed nickel-cobalt oxide (NCO) crystals. NixCo1-xO was prepared in-situ by high-temperature oxygen-assisted molecular beam epitaxy on a Ru(0001) single crystal substrate. To check the effect of incorporating Ni into the cobalt oxide films, three different compositions were prepared. The element-specific XMLD measurements reveal strong antiferromagnetic contrast at room temperature and magnetic domains up to one micron in size, reflecting the high structural quality of the NCO islands. By means of vectorial magnetometry, the antiferromagnetic spin axis orientation of the domains was determined with nanometer spatial resolution, and found to depend on the stoichiometry of the prepared crystals., This research was funded by the SciMat Priority Research Area budget under the program Excellence Initiative - Research University at the Jagiellonian University in Kraków - Grant No. 75.1920.2021, by Projects No. PID2021-124585NB-C31 and PID2021-124585NB-C33 funded by MCIN/AEI/10.13039/501100011033 and by ‘‘ERDF A way of making Europe’’ and by Projects No. TED2021-130957B-C54 and TED2021-130957B-C51 funded by MCIN/AEI/10.13039/501100011033 and by the ‘‘European Union NextGenerationEU/PRTR’’. C.G.-M. acknowledges financial support from grant RYC2021-031181-I funded by MCIN/AEI/10.13039/501100011033 and by the ‘‘European Union NextGenerationEU/PRTR’’., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Stacking influence on the in-plane magnetic anisotropy in a 2D magnetic system

  • Ruiz-Gómez, Sandra
  • Pérez, Lucas
  • Mascaraque, Arantzazu
  • Santos, B.
  • El Gabaly, Farid
  • Schmid, Andreas K.
  • de la Figuera, Juan
7 pags., 4 figs., The magnetization patterns on three atomic layers thick islands of Co on Ru(0001) are studied by spin-polarized low-energy electron microscopy (SPLEEM). In-plane magnetized micrometer wide triangular Co islands are grown on Ru(0001). They present two different orientations correlated with two different stacking sequences which differ only in the last layer position. The stacking sequence determines the type of magnetization pattern observed: the hcp islands present very wide domain walls, while the fcc islands present domains separated by much narrower domain walls. The former is an extremely low in-plane anisotropy system. We estimate the in-plane magnetic anisotropy of the fcc regions to be 1.96 × 104 J m-3 and of the hcp ones to be 2.5 × 102 J m-3., This work is supported by the Grants PID2021-124585NB-C31, PID2020-117024GB-C43 and TED2021-130957B-C54 funded by MCIN/AEI/10.13039/501100011033, by “ERDF A way of making Europe” and by the “European Union NextGenerationEU/PRTR”, by the Grant S2018-NMT-4321 funded by the Comunidad de Madrid, by “ERDF A way of making Europe”, and by the Office of Science, Office of Basic Energy Sciences,Scientific User Facilities Division, of the U.S. Department of Energy under contract no. DE-AC02—05CH11231. S. RuizGomez thanks the Alexander Von Humboldt Foundation for financial support. Sandia National Laboratories is a multimission laboratory managed and operated by the National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International Inc. for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525. This paper describes objective technical results and analysis. Any subjective views or opinions that might be expressed in the paper do not necessarily represent the views of the U.S. Department of Energy or the United States Government., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and characterisation of the new oxyanion doped “0201–1201” type layered oxide, Sr4.5Fe2(S/Cr)0.5O9±δ

  • Jarvis, A.
  • Berry, F. J.
  • Marco, J.F.
  • Cibin, G.
  • Slater, P. R.
7 pags., 7 figs., 4 tabs., This work reports on an oxyanion containing Sr–Fe–O perovskite-related layered oxide system related to the “0201–1201” type material Sr4.5Cr2.5O9. Using solid state synthesis, we successfully incorporate SO42− and CrO42− to give Sr4.5Fe2(S/Cr)0.5O9±δ, with X-ray and neutron diffraction used to analyse the structure of these materials. Neutron diffraction experiments combined with 57Fe Mössbauer spectroscopy and X-ray absorption spectroscopy show not only the successful oxyanion incorporation, but also that these systems have the ability to accommodate excess interstitial anions. The stabilisation of these new phases highlights the potential to synthesise new perovskite-related compounds using oxyanion doping., We would like to thank the University of Birmingham and EPSRC for funding (studentship for AJ). The authors also thank EPSRC for funding: the JUICED Hub (Joint University Industry Consortium for Energy (Materials) and Devices Hub), EP/R023662/1). We would like to thank the STFC ISIS Facility for the provision of neutron diffraction time, and Dr. A. Gibbs for help with data collection. We thank Diamond Light Source for the award of beam time as part of the Energy Materials Block Allocation Group. This work has been supported by Project No. TED2021-130957B–C54 funded by MCIN/AEI/10.13039/ 501100011033 and by the ‘‘European Union NextGenerationEU/ PRTR’’., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

ICEMS Characterization of NixFe3-xO4 (0.7 ≤ x ≤ 1.7) thin films grown by ion beam sputtering on (0001) Al2O3 substrates

  • Prieto, P.
  • Prieto, J. E.
  • Serrano, A.
  • de la Figuera, Juan
  • Marco, J.F.
10 pags., 3 figs., 2 tabs., We report here on the ICEMS characterization of nickel ferrite (NiFeO) thin films having different nickel contents grown on alumina substrates by Ion Beam Sputtering. The spectra corresponding to the films with nominal x = 0.7, 1.0 and 1.2 are characteristic of compounds crystallizing in a spinel-related structure showing two different magnetic sextets associated with Fe located in the tetrahedral and octahedral sites of such structure. The spectra show an additional broad third sextet with a large isomer shift which suggests the occurrence of electron hopping between Fe and Fe ions sitting in the octahedral sites. With increasing nickel content, the linewidth of the sextets increases and their corresponding hyperfine magnetic fields decrease. This is an indication of an increase in structural disorder in the deposited films as their nickel concentrations increase. The cation distribution of the iron ions over the tetrahedral and octahedral sites appears also to depend on the nickel content. The film with x = 1.2 shows a significant increase in the fraction of octahedral iron ions as compared with the expected nominal value suggesting that, for this composition, some Ni could also occupy tetrahedral sites. The Mössbauer spectrum corresponding to the film with x = 1.7 shows a magnetic pattern with very broad lines similar to those shown by amorphous or disordered materials. The average isomer shift is quite high (around 0.40 mms) and characteristic of Fe in octahedral oxygen coordination. This indicates that for the largest nickel content studied (x = 1.7), the film does not contain Fe in tetrahedral environments suggesting that the spinel structure is no longer present. This correlates well with the X-Ray Diffraction data which indicate a structural change from spinel to a disordered rock-salt structure for this particular film with high nickel content., This work has been supported by projects PID2021-124585NB-C31, PID2021-124585NB-C32 and PID2021-124585NB-C33 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by ‘‘ERDF A way of making Europe’’ and by Project No. TED2021-130957B-C51, TED2021-130957B-C54 and TED2021-130196B-C22 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the ‘‘European Union NextGenerationEU/PRTR’’. The authors also thank financial support from the Consejería de Educación e Investigación de la Comunidad de Madrid (NANOMAGCOST-CM Ref. P2018/NMT-4321) and from the Comunidad de Madrid and Universidad Autónoma de Madrid under the V PRICIT program through the Project SI3/PJI/2021 − 00393. A. S. acknowledges financial support from grant RYC2021-031236-I funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the “European Union NextGenerationEU/ PRTR”. Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

ICEMS Characterization of NixFe3-xO4 (0.7 ≤ x ≤ 1.7) thin films grown by ion beam sputtering on (0001) Al2O3 substrates

  • Prieto, P.
  • Prieto, J. E.
  • Serrano, A.
  • de la Figuera, Juan
  • Marco, J.F.
10 pags., 3 figs., 2 tabs., We report here on the ICEMS characterization of nickel ferrite (NiFeO) thin films having different nickel contents grown on alumina substrates by Ion Beam Sputtering. The spectra corresponding to the films with nominal x = 0.7, 1.0 and 1.2 are characteristic of compounds crystallizing in a spinel-related structure showing two different magnetic sextets associated with Fe located in the tetrahedral and octahedral sites of such structure. The spectra show an additional broad third sextet with a large isomer shift which suggests the occurrence of electron hopping between Fe and Fe ions sitting in the octahedral sites. With increasing nickel content, the linewidth of the sextets increases and their corresponding hyperfine magnetic fields decrease. This is an indication of an increase in structural disorder in the deposited films as their nickel concentrations increase. The cation distribution of the iron ions over the tetrahedral and octahedral sites appears also to depend on the nickel content. The film with x = 1.2 shows a significant increase in the fraction of octahedral iron ions as compared with the expected nominal value suggesting that, for this composition, some Ni could also occupy tetrahedral sites. The Mössbauer spectrum corresponding to the film with x = 1.7 shows a magnetic pattern with very broad lines similar to those shown by amorphous or disordered materials. The average isomer shift is quite high (around 0.40 mms) and characteristic of Fe in octahedral oxygen coordination. This indicates that for the largest nickel content studied (x = 1.7), the film does not contain Fe in tetrahedral environments suggesting that the spinel structure is no longer present. This correlates well with the X-Ray Diffraction data which indicate a structural change from spinel to a disordered rock-salt structure for this particular film with high nickel content., This work has been supported by projects PID2021-124585NB-C31, PID2021-124585NB-C32 and PID2021-124585NB-C33 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by ‘‘ERDF A way of making Europe’’ and by Project No. TED2021-130957B-C51, TED2021-130957B-C54 and TED2021-130196B-C22 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the ‘‘European Union NextGenerationEU/PRTR’’. The authors also thank financial support from the Consejería de Educación e Investigación de la Comunidad de Madrid (NANOMAGCOST-CM Ref. P2018/NMT-4321) and from the Comunidad de Madrid and Universidad Autónoma de Madrid under the V PRICIT program through the Project SI3/PJI/2021 − 00393. A. S. acknowledges financial support from grant RYC2021-031236-I funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the “European Union NextGenerationEU/ PRTR”. Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

ICEMS Characterization of NixFe3-xO4 (0.7 ≤ x ≤ 1.7) thin films grown by ion beam sputtering on (0001) Al2O3 substrates

  • Prieto, P.
  • Prieto, J. E.
  • Serrano, A.
  • de la Figuera, Juan
  • Marco, J.F.
10 pags., 3 figs., 2 tabs., We report here on the ICEMS characterization of nickel ferrite (NiFeO) thin films having different nickel contents grown on alumina substrates by Ion Beam Sputtering. The spectra corresponding to the films with nominal x = 0.7, 1.0 and 1.2 are characteristic of compounds crystallizing in a spinel-related structure showing two different magnetic sextets associated with Fe located in the tetrahedral and octahedral sites of such structure. The spectra show an additional broad third sextet with a large isomer shift which suggests the occurrence of electron hopping between Fe and Fe ions sitting in the octahedral sites. With increasing nickel content, the linewidth of the sextets increases and their corresponding hyperfine magnetic fields decrease. This is an indication of an increase in structural disorder in the deposited films as their nickel concentrations increase. The cation distribution of the iron ions over the tetrahedral and octahedral sites appears also to depend on the nickel content. The film with x = 1.2 shows a significant increase in the fraction of octahedral iron ions as compared with the expected nominal value suggesting that, for this composition, some Ni could also occupy tetrahedral sites. The Mössbauer spectrum corresponding to the film with x = 1.7 shows a magnetic pattern with very broad lines similar to those shown by amorphous or disordered materials. The average isomer shift is quite high (around 0.40 mms) and characteristic of Fe in octahedral oxygen coordination. This indicates that for the largest nickel content studied (x = 1.7), the film does not contain Fe in tetrahedral environments suggesting that the spinel structure is no longer present. This correlates well with the X-Ray Diffraction data which indicate a structural change from spinel to a disordered rock-salt structure for this particular film with high nickel content., This work has been supported by projects PID2021-124585NB-C31, PID2021-124585NB-C32 and PID2021-124585NB-C33 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by ‘‘ERDF A way of making Europe’’ and by Project No. TED2021-130957B-C51, TED2021-130957B-C54 and TED2021-130196B-C22 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the ‘‘European Union NextGenerationEU/PRTR’’. The authors also thank financial support from the Consejería de Educación e Investigación de la Comunidad de Madrid (NANOMAGCOST-CM Ref. P2018/NMT-4321) and from the Comunidad de Madrid and Universidad Autónoma de Madrid under the V PRICIT program through the Project SI3/PJI/2021 − 00393. A. S. acknowledges financial support from grant RYC2021-031236-I funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the “European Union NextGenerationEU/ PRTR”. Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

ICEMS Characterization of NixFe3-xO4 (0.7 ≤ x ≤ 1.7) thin films grown by ion beam sputtering on (0001) Al2O3 substrates

  • Prieto, P.
  • Prieto, J. E.
  • Serrano, A.
  • de la Figuera, Juan
  • Marco, J.F.
10 pags., 3 figs., 2 tabs., We report here on the ICEMS characterization of nickel ferrite (NiFeO) thin films having different nickel contents grown on alumina substrates by Ion Beam Sputtering. The spectra corresponding to the films with nominal x = 0.7, 1.0 and 1.2 are characteristic of compounds crystallizing in a spinel-related structure showing two different magnetic sextets associated with Fe located in the tetrahedral and octahedral sites of such structure. The spectra show an additional broad third sextet with a large isomer shift which suggests the occurrence of electron hopping between Fe and Fe ions sitting in the octahedral sites. With increasing nickel content, the linewidth of the sextets increases and their corresponding hyperfine magnetic fields decrease. This is an indication of an increase in structural disorder in the deposited films as their nickel concentrations increase. The cation distribution of the iron ions over the tetrahedral and octahedral sites appears also to depend on the nickel content. The film with x = 1.2 shows a significant increase in the fraction of octahedral iron ions as compared with the expected nominal value suggesting that, for this composition, some Ni could also occupy tetrahedral sites. The Mössbauer spectrum corresponding to the film with x = 1.7 shows a magnetic pattern with very broad lines similar to those shown by amorphous or disordered materials. The average isomer shift is quite high (around 0.40 mms) and characteristic of Fe in octahedral oxygen coordination. This indicates that for the largest nickel content studied (x = 1.7), the film does not contain Fe in tetrahedral environments suggesting that the spinel structure is no longer present. This correlates well with the X-Ray Diffraction data which indicate a structural change from spinel to a disordered rock-salt structure for this particular film with high nickel content., This work has been supported by projects PID2021-124585NB-C31, PID2021-124585NB-C32 and PID2021-124585NB-C33 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by ‘‘ERDF A way of making Europe’’ and by Project No. TED2021-130957B-C51, TED2021-130957B-C54 and TED2021-130196B-C22 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the ‘‘European Union NextGenerationEU/PRTR’’. The authors also thank financial support from the Consejería de Educación e Investigación de la Comunidad de Madrid (NANOMAGCOST-CM Ref. P2018/NMT-4321) and from the Comunidad de Madrid and Universidad Autónoma de Madrid under the V PRICIT program through the Project SI3/PJI/2021 − 00393. A. S. acknowledges financial support from grant RYC2021-031236-I funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by the “European Union NextGenerationEU/ PRTR”. Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Data for in situ modification of the magnetocrystalline anisotropy in cobalt-ferrite microcrystals

  • Mandziak, Anna
  • Prieto, J. E.
  • Dávalos, J.Z.
  • Prieto, Pilar
  • Foerster, Michael
  • Aballe, Lucía
  • de la Figuera, Juan
[Description of methods used for collection/generation of data: ] X-ray absorption spectroscopy and X-ray magnetic circular dichroism in photoemission electron microscopy., [Methods for processing the data] Intensity extracted from sequence of images at different photon energies, after manual drift correction. Vector magnetization extracted using the protocol described in https://surfmoss.iqf.csic.es/en/2013-04-02-10-34-02/manuals-howtos/90-vector-xcmd-peem-spleem, We present the in situ modification of the magnetocrystalline anisotropy of iron-rich cobalt-ferrite epitaxial islands by changing their composition. Crystalline cobalt-ferrite spinel islands have been grown by oxygen-assisted molecular beam epitaxy on a Ru(0001) single crystal. The micro-crystals are several micrometers wide with heights of tens of nanometers. Their spatially-resolved vector magnetization is mapped by x-ray magnetic circular dichroism in photoemission microscopy at the L3 absorption edges of Co and Fe. Thick islands present a closure-like magnetic domain structure with the magnetization directions predominantly aligned along the projections of the easy magnetic axes onto the (111) surface plane. Thinner islands are more affected by growth defects and present a more complex domain structure. Upon deposition of additional Fe in an oxygen background pressure, Co is found to segregate out of the spinel islands, while their Fe content increases. This produces a reduction in the magnetocrystalline anisotropy, which manifests as a reorientation of the magnetization directions towards the edges of the islands, reflecting an increased contribution of the shape anisotropy, AMADEUS PID2021-124585NB-C31, PID2021-124585NB-C32), Nanobond (TED2021-130196B-C22, TED2021-130957B-C54), PID2020-117024GB-C43, TED2021-130957B-C54., File List: - Characterization of as-grown sample - XAS PEEM Images: Fe, Co, O folders - XAS XMCD Images at 0, 60, and 120 degrees azimuthal rotation: Fe - Growth sequence of LEEM images - Characterization of modified sample - XAS PEEM Images: Fe, Co - XAS XMCD Images at 0, 60, 120 degrees azimuthal rotation: Fe, Co - Micromagnetic simulations - Input files - Auxiliary data - Calibration of counts vs. Channel plates voltage - Logbook of experiments, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and Characterization of HfO2@Fe3O4 Core–Shell Nanotubes: Insights into Potential Magnetic Functionalities

  • Grifferos, Lukas
  • Alburquenque, Daniela
  • Vargas, Javiera
  • Kumar, Chandra
  • Saavedra, Eduardo
  • Pereira, Alejandro
  • Marco, J.F.
  • Escrig, Juan
11 pages, 7 figures, 1 table, This study presents the synthesis and characterization of core-shell nanostructures comprising PVP@HfO2@Fe2O3 nanowires and HfO2@Fe3O4 nanotubes. PVP nanofibers were electrospun with an average diameter of approximately 379 nm, onto which HfO2 and Fe2O3 layers were sequentially deposited via atomic layer deposition, resulting in core-shell nanowires averaging 460 nm in diameter. Thermal reduction transformed Fe2O3 into Fe3O4, forming HfO2@Fe3O4 core-shell nanotubes. Characterization using scanning electron microscopy and high-resolution transmission electron microscopy confirmed the core-shell morphology, while energy-dispersive X-ray spectroscopy verified the elemental composition. Surface roughness analysis revealed fractal dimensions indicating increased roughness with thicker shells. X-ray photoelectron spectroscopy analysis identified Fe(II) and Fe(III) oxidation states and confirmed phase transformations from hematite to magnetite. Magnetic measurements demonstrated enhanced coercivity and saturation magnetization in HfO2@Fe3O4 structures compared to initial samples, showcasing the tunability of magnetic properties through core-shell engineering. This work highlights atomic layer deposition’s capability to fabricate precise core-shell nanostructures, offering tailored control over morphology and magnetic behavior for applications in advanced nanotechnologies., The authors gratefully acknowledge financial support from the ANID through Basal Financing for Scientific and Techno-logical Centers of Excellence (Grant AFB220001). Addition-ally, we acknowledge support from FONDECYT (Grants1240829 and 11230889), FONDEQUIP (GrantsEQM120045, EQM140092, and EQM190027), and DICYT-USACH (Grant 042431EM_Ayudante). We also extend ourappreciation to the Spanish Agencia Estatal de Investigación under Grants TED2021-130957B-C54 and PID2021-124585NB-C31, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural and magnetic properties of the Fe3 O4 (110) surface

  • Mandziak, Anna
  • Prieto, J. E.
  • Gutiérrez-Cuesta, Clara
  • Niño, Miguel Ángel
  • Foerster, Michael
  • de la Figuera, Juan
  • Nita, Pawel
8 pages, 5 figures, This research was funded by the SciMat Priority Research Area budget under the program Excellence Initiative - Research University at the Jagiellonian University in Kraków - Grant No. 75.1920.2021, by Projects No. PID2021-124585NB-C31, PID2021-122980OB-C54 and TED2021-130957B-C54 funded by MCIN/ AEI/10.13039/501100011033, by “ERDF A way of making Europe” and by the “European Union NextGenerationEU/PRTR”. This publication was partially developed under the provision of the Polish Ministry and Higher Education project “Support for research and development with the use of research infra-structure of the National Synchrotron Radiation Centre SOLARIS” under contract no 1/SOL/2021/2., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Data for Growth of MnWO4 Nanowires on W(110) by High- Temperature Oxygen-Assisted Molecular Beam Epitaxy

  • Fornal, Kalina
  • Gutiérrez-Cuesta, Clara
  • Campo, Ángel Adolfo del
  • Mandziak, Anna
  • Nita, Pawel
  • Prieto, J. E.
  • Marco, J.F.
  • de la Figuera, Juan
[Description of methods used for collection/generation of data] X-ray absorption spectroscopy and X-ray magnetic circular dichroism in photoemission electron microscopy, low-energy electron microscopy, Raman spectroscopy, Optical microscopy, Atomic Force Microscopy, [Methods for processing the data] Intensity extracted from areas of interest from sequence of images at different photon energies, or different start voltage., Dataset for the growth of synthetic hübnerite (MnWO4) by high-temperature oxygen-assisted molecular beam epitaxy on W(110). The hübnerite nanowires have widths of hundreds of nanometers, heights of tens of nanometers and lengths in the range of millimeters. The growth was followed in real time by low-energy electron microscopy (LEEM). The nanowires are characterized in situ by low-energy electron microscopy, x-ray absorption and x-ray photoelectron spectroscopy in photoemission microscopy, as well as ex situ by atomic force microscopy, optical microscopy and Raman spectroscopy. Hübnerite can be grown on W(110) by dosing only manganese in a molecular oxygen environment, likely due to the formation of highly mobile WOx species with diffusion lengths of the order of hundreds of micrometers. The dataset comprises the original LEEM data for the growth movie, the PEEM data for the Mn, the O XAS spectra and the W XPS spectra (all of them reduced in size by half), and the Raman spectrum and the AFM image., AMADEUS (AEI PID2021-124585NB-C31), Nanobond (AEI TED2021-130957B-C54), BEETHOVEN (EU 101129912), Polish (1/SOL/2021/2)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Data for Magnetic Circular Dichroism at the Oxygen K edge in Microcrystals of Spinels Grown on Ru(0001) (arxiv 2505.24439)

  • Mandziak, Anna
  • Sosa, V.
  • Nita, Pawel
  • Martín-García, Laura
  • Prieto, J. E.
  • Foerster, Michael
  • Niño, Miguel Ángel
  • Aballe, Lucía
  • Granados-Miralles, Cecilia
  • Quesada, Adrián
  • Tejera-Centeno, César
  • Gallego, Silvia
  • de la Figuera, Juan
[Description of methods used for collection/generation of data] X-ray absorption spectroscopy and X-ray magnetic circular dichroism in photoemission electron microscopy., We have measured the circular magnetic dichroism in the x-ray absorption at the K-edge of oxygen in microcrystals of different spinel oxides. The microcrystals are islands of micrometric size and nanometric thickness, grown on Ru(0001) substrates using high-temperature oxygen-assisted molecular beam epitaxy. The domains observed in the oxygen K-edge dichroism have the same distribution and orientation as those observed in x-ray magnetic circular dichroism at the L3 edge of the octahedral cations. Integrating the area from a single domain, x-ray magnetic circular dichroic spectra of oxygen were measured and, by the application of the K-edge sum rule, non vanishing orbital magnetic moments aligned with the octahedral cations were found. The work is described in arXiv:2505.24439. The dataset comprises the original raw PEEM data for the XMCD images and the XAS spectra in both the cobalt ferrite and the nickel ferrite. The PEEM images have only been reduced in size by half in each direction to reduce the size (and saved in a single TIFF file for each measurement)., AMADEUS (PID2021-124585NB-C31, PID2021-124585NB-C33), Nanobond (TED2021-130196B-C22, TED2021-130957B-C54)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Magnetic Circular Dichroism at the Oxygen K edge in Microcrystals of Spinels Grown on Ru(0001)

  • Mandziak, Anna
  • Sosa, V.
  • Nita, Pawel
  • Martín-García, Laura
  • Prieto, J. E.
  • Foerster, Michael
  • Niño, Miguel Ángel
  • Aballe, Lucía
  • Granados-Miralles, Cecilia
  • Quesada, Adrián
  • Tejera-Centeno, César
  • Gallego, Silvia
  • de la Figuera, Juan
We have measured the circular magnetic dichroism in the x-ray absorption at the K-edge of oxygen in microcrystals of different spinel oxides. The microcrystals are islands of micrometric size and nanometric thickness, grown on Ru(0001) substrates using high-temperature oxygen-assisted molecular beam epitaxy. The domains observed in the oxygen K-edge dichroism have the same distribution and orientation as those observed in x-ray magnetic circular dichroism at the L edge of the octahedral cations. Integrating the area from a single domain, x-ray magnetic circular dichroic spectra of oxygen were measured and, by the application of the K-edge sum rule, non vanishing orbital magnetic moments aligned with the octahedral cations were found. Density functional theory calculations, which did not show any orbital moment at the oxygen anions, indicate that the energy ranges where oxygen dichroism is observed correspond to those with significant hybridization with the cations d bands. They also show a correlation between the magnitude of the measured value of the oxygen orbital moment and the theoretical one for the cations, and demonstrate that this trend is preserved in the presence of Fe excess in the samples. Our experimental XMCD suggest, following the DFT calculations, that the origin of the oxygen magnetic moment lies in the hybridization of the oxygen unoccupied p-derived bands with the cation bands, mostly with the d-derived ones., This work is supported by the Grants PID2021-124585NB-C31/-C33, PID2021-122980OB-C55, PID2020-117024GB-C43 and TED2021-130957B-C53/-C54 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” and by the ”European Union NextGenerationEU/PRTR”. P. N. acknowledges the SciMat Priority Research Area budget under the program Excellence Initiative - Research University at the Jagiellonian University in Krakow - Grant No. 75.1920.2021These experiments were performed at the CIRCE beamline of the ALBA Synchrotron Light Facility. V.S. acknowledges financial support from PIPF-2023/ECO-30425., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetic circular dichroism at the oxygen K-edge in microcrystals of spinels grown on Ru(0001)

  • Mandziak, Anna
  • Sosa, Victor
  • Nita, Pawel
  • Martín-García, Laura
  • Prieto, J. E.
  • Foerster, Michael
  • Niño, Miguel Ángel
  • Aballe, Lucia
  • Granados-Miralles, Cecilia
  • Quesada, Adrián
  • Tejera-Centeno, César
  • Gallego, Silvia
  • de la Figuera, Juan
10 pages, 3 figures, 4 tables, We have measured the circular magnetic dichroism in the x-ray absorption at the K-edge of oxygen in microcrystals of different spinel oxides. The microcrystals are islands of micrometric size and nanometric thickness, grown on Ru(0001) substrates using high-temperature oxygen-assisted molecular beam epitaxy. The domains observed in the oxygen K-edge dichroism have the same distribution and orientation as those observed in x-ray magnetic circular dichroism at the L3edge of the octahedral cations. Integrating the area from a single domain, x-ray magnetic circular dichroic spectra of oxygen were measured and, by the application of the K-edge sum rule, non vanishing orbital magnetic moments aligned with the octahedral cations were found. Density functional theory calculations, which did not show any orbital moment at the oxygen anions, indicate that the energy ranges where oxygen dichroism is observed correspond to those with significant hybridization with the cations d bands. They also show a correlation between the magnitude of the measured value of the oxygen orbital moment and the theoretical one for the cations, and demonstrate that this trend is preserved in the presence of Fe excess in the samples. Our experimental XMCD suggest, following the density functional theory calculations, that the origin of the oxygen magnetic moment lies in the hybridization of the oxygen unoccupied p-derived bands with the cation bands, mostly with the d-derived ones and does not correspond to a localized orbital magnetic moment in the oxygen in spinels., This work is supported by the Grants PID2021124585NB-C31/-C33, PID2021-122980OB-C55, PID2020117024GB-C43 and TED2021-130957B-C53/-C54 funded by MCIN/AEI/10.13039/501100011033 and by ‘ERDF A way of making Europe’ and by the ‘European Union Next Generation EU/PRTR’. P N acknowledges the SciMat Priority Research Area budget under the program Excellence Initiative—Research University at the Jagiellonian University in Craków—Grant No. 75.1920.2021. C G-M acknowledges f inancial support from Grant RYC2021–031181-I funded by MCIN/AEI/10.13039/501100011033 and by the ‘European Union NextGenerationEU/PRTR’. These experiments were performed at the CIRCE beamline of the ALBA Synchrotron Light Facility. V S acknowledges financial support from PIPF2023/ECO-30425., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Anisotropic growth of ferberite (FeWO4) on W(110) by high-temperature oxygen-assisted molecular beam epitaxy

  • Gutiérrez-Cuesta, Clara
  • del Campo, Adolfo
  • Rojo-Silva, V.
  • Marco, J.F.
  • Cojocariu, Iulia
  • Szpytma, Marcin
  • Fevola, Giovanni
  • Mascaraque, Arantzazu
  • Menteş, Tevfik Onur
  • Locatelli, Andrea
  • Quesada, Adrián
  • de la Figuera, Juan
  • Prieto, J. E.
8 pages, 6 figures, 1 table, We report on the growth of nanowires of ferberite (FeWO<inf>4</inf>) by high-temperature oxygen-assisted molecular beam epitaxy on W(110). This multifunctional material has promising applications in different fields. The wires extend for several millimeters in length, with widths in the hundreds and heights in the tens of nanometers. We have monitored the growth process by real-time low-energy electron microscopy and characterized the wires in-situ by low-energy electron microscopy and laterally-resolved X-ray absorption and photoelectron spectroscopies. Further analysis was performed ex-situ by atomic force and optical microscopies as well as by Raman spectroscopy. The growth of ferberite on W(110) was possible by dosing iron in a molecular oxygen atmosphere likely due to the formation of highly mobile WO<inf>x</inf> units that can be incorporated into the anisotropic wolframite structure, which in turn is responsible for the highly anisotropic growth. We propose that the same method may be used for the growth of other tungstate or related compounds., This work is supported by Grants PID2021-124585NB-C31, PID2021-124585NB-C33, TED2021-130957B-C54 and TED2021-130957B-C51 funded by MCIN/AEI/10.13039/501100011033, by “ERDF A way of making Europe” and by the “European Union NextGenerationEU/PRTR”; by Grant Mag4TIC-CM funded by the TEC-2024/TEC-380 program of the Comunidad de Madrid and by the BEETHOVEN project funded by the European Commission under grant agreement 101129912. It is also funded by the European Union as part of the Horizon Europe call HORIZON-INFRA-2021-SERV-01 under grant agreement number 101058414 and co-funded by UK Research and Innovation (UKRI) under the UK government’s Horizon Europe funding guarantee (grant number 10039728) and by the Swiss State Secretariat for Education, Research and Innovation (SERI) under contract number 22.00187. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or the European Education and Culture Executive Agency (EACEA) or the UK Science and Technology Facilities Council or the Swiss State Secretariat for Education, Research and Innovation (SERI). Neither the European Union nor EACEA or the granting authorities can be held responsible for them., Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

Anisotropic growth of ferberite (FeWO4) on W(110) by high-temperature oxygen-assisted molecular beam epitaxy

  • Gutiérrez-Cuesta, Clara
  • del Campo, Adolfo
  • Rojo, Víctor
  • Marco, José F.
  • Cojocariu, Iulia
  • Szpytma, Marcin
  • Fevola, Giovanni
  • Mascaraque Susunaga, Arantzazu
  • Menteş, Tevfik Onur
  • Locatelli, Andrea
  • Quesada, Adrián
  • de la Figuera, Juan
  • Prieto, José Emilio
We report on the growth of nanowires of ferberite (FeWO) by high-temperature oxygen-assisted molecular beam epitaxy on W(110). This multifunctional material has promising applications in different fields. The wires extend for several millimeters in length, with widths in the hundreds and heights in the tens of nanometers. We have monitored the growth process by real-time low-energy electron microscopy and characterized the wires in-situ by low-energy electron microscopy and laterally-resolved X-ray absorption and photoelectron spectroscopies. Further analysis was performed ex-situ by atomic force and optical microscopies as well as by Raman spectroscopy. The growth of ferberite on W(110) was possible by dosing iron in a molecular oxygen atmosphere likely due to the formation of highly mobile WO units that can be incorporated into the anisotropic wolframite structure, which in turn is responsible for the highly anisotropic growth. We propose that the same method may be used for the growth of other tungstate or related compounds.