Pasar al contenido principal

METAMATERIALES PARA LA GENERACION DE ENERGIA

PID2020-118430GB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

DIGITAL.INTA Repositorio Digital del Instituto Nacional de Técnica Aeroespacial
Publicación Contribución de congreso (ConferenceOutput)

Magnetic interactions in ordered cobalt three-dimensional nanonetworks

  • Ruiz Clavijo, Alejandra
  • Caballero Calero, Olga
  • Navas, David
  • Vivas, Laura G.
  • Martín González, Marisol
  • Martín-Rubio, Carolina
  • Sanz, Ruy
Trabajo presentado en el 13th Joint European Magnetic Symposia - JEMS, celebrado en Madrid (España), del 27 de agosto al 1 de septiembre de 2023, "Three-Dimensional (3D) magnetic nanostructures allow the generation and control of new effects able to give rise to the next generation of functional magnetic nanostructured metamaterials and devices[1]. This work reports the results on the synthesis and characterization of different interconnected Co nanowires forming a dense and ordered magnetic system: Co 3D Nanowire Networks (3DNN). These nanostructures were synthesized by the electrodeposition of Co in 3D ordered porous alumina templates [2] [3] [4]. The route allows to control the order and some geometric features compared to other synthesis approaches [1]. The resulting 3DNN consists of hexagonal ordered nanowires with an inter-wire distance of 65 nm and 50 nm in diameter. These nanowires are interconnected with a net of perpendicular or transversal nanowires (TNW) of ≈ 30 nm in diameter. Meanwhile the TNW are distributed in levels with a well defined distance between them of 550 nm. The magnetic characterization consisted in hysteresis loops, first magnetization curves and first order reversal curves (FORC) at 0º (in-plane, IP) 30º, 60º and 90º (out of plane, OOP) from perpendicular NW main axis. 1.D. Bhattacharya, et al. Nano Lett. (2022), 22, 24, 10010–10017. 2.J. Martín, et. al., Nat. Commun. 5, (2014) 5130. 3.A. Ruiz-Clavijo, et al. Phys. Status Solidi RRL, 13 (2019), 1900263. 4.A. Ruiz-Clavijo, et al., Adv. Electron. Mater. 8, (2022) 2200342", This work was supported by PID2020-118430GB-100, PID2020-115325GB-C31, RYC-2017-22820 funded by MCIN/AEI/ 10.13039/501100011033., Preprint
DIGITAL.INTA Repositorio Digital del Instituto Nacional de Técnica Aeroespacial
Publicación Artículo científico (JournalArticle)

Unveiling the Complex Magnetization Reversal Process in 3D Nickel Nanowire Networks

  • Ruiz Clavijo, Alejandra
  • Caballero Calero, Olga
  • Navas, David
  • Ordoñez Cencerrado, Amanda A.
  • Blanco Portals, J.
  • Peiró, F.
  • Martín González, Marisol
  • Sanz, Ruy
Understanding the interactions among magnetic nanostructures is one of the key factors to predict and control the advanced functionalities of 3D integrated magnetic nanostructures. In this work, the focus is on different interconnected Ni nanowires forming an intricate, but controlled, and ordered magnetic system: Ni 3D Nanowire Networks (3DNNs). These self-ordered systems present striking anisotropic magnetic responses, depending on the interconnections’ position between nanowires. To understand their collective magnetic behavior, the magnetization reversal processes are studied within different Ni 3D Nanowire Networks compared to the 1D nanowire 1DNW array counterparts. The systems are characterized at different angles using first magnetization curves, hysteresis loops, and First Order Reversal Curves techniques, which provided information about the key features that enable macroscopic tuning of the magnetic properties of the 3D nanostructures. In addition, micromagnetic simulations endorse the experiments, providing accurate modeling of their magnetic behavior. The results reveal a plethora of magnetic interactions, neither evident nor intuitive, which are the main role players controlling the collective response of the system. The results pave the way for the design and realization of 3D novel metamaterials and devices based on the nucleation and propagation of ferromagnetic domain walls both in 3D self-ordered systems and future nano-lithographed devices., M.M.G. and O.C.C. acknowledge the financial support from the project PID2020-118430GB-100 (MICINN). J.B.P., and F.P. acknowledge the financial support from PID2019-106165GB-C21 (MICINN) and M. López-Haro and J.J. Calvino from the University of Cádiz for the acquisition of the electron tomography series. The authors also acknowledge the service from the X-SEM Laboratory at IMM, and funding from MINECO under project CSIC13-4E-1794 with support from the EU (FEDER, FSE). The authors acknowledge the support for simulation hardware from J.L. Mesa at INTA. D.N. acknowledges the financial support from the project PID2019-108075RB-C31 and the grant RYC-2017-22820 funded by MICINN/10.13039/501100011033 and by “ESF Investing in your future”., Peerreview
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D Bi2Te3 Interconnected Nanowire Networks to Increase Thermoelectric Efficiency

  • Ruiz-Clavijo, Alejandra
  • Caballero-Calero, Olga
  • Manzano, Cristina V.
  • Maeder, Xavier
  • Beardo, Albert
  • Cartoixà, Xavier
  • Álvarez, F. Xavier
  • Martín-González, Marisol
3D interconnected nanowire scaffoldings are shown to increase the thermoelectric efficiency in comparison to similar diameter 1D nanowires and films grown under similar electrodeposition conditions. Bi2Te3 3D nanonetworks offer a reduction in thermal conductivity (¿T) while preserving the high electrical conductivity of the films. The reduction in ¿T is modeled using the hydrodynamic heat transport equation, and it can be understood as a heat viscosity effect due to the 3D nanostructuration. In addition, the Seebeck coefficient is twice that of nanowires and films, and up to 50% higher than in a single crystal. This increase is interpreted as a nonequilibrium effect that the geometry of the structure induces on the distribution function of the phonons, producing an enhanced phonon drag. These thermoelectric metamaterials have higher performance and are fabricated with large areas by a cost-effective method, which makes them suitable for up-scale production, The authors acknowledge financial support from Spanish Ministerio de Ciencia, Innovación y Universidades under Grants [PID2020-118430GB-100, RTI2018-097876-B-C22 (MCIU/AEI/FEDER, UE), and RTI2018-097876-B-C21 (MCIU/AEI/FEDER, UE)] and the CSIC project 2DMESES. Cristina V. Manzano acknowledges funding from “Atracción de Talento Investigador” de la Comunidad de Madrid, contract [2019-T1/IND-13541]. The authors ac knowledge the service from the MiNa Laboratory at IMN and funding from CM (project SpaceTec, [S2013/ICE2822]), MINECO (project [CSIC13-4E-1794]), and EU (FEDER, FSE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The Thermoelectric Properties of Spongy PEDOT Films and 3D-Nanonetworks by Electropolymerization

  • Manzano, Cristina V.
  • Caballero-Calero, Olga
  • Serrano Rubio, Aída
  • Resende, Pedro M.
  • Martín-González, Marisol
Recently, polymers have been attracted great attention because of their thermoelectric materials’ excellent mechanical properties, specifically their cost-effectiveness and scalability at the industrial level. In this study, the electropolymerization conditions (applied potential and deposition time) of PEDOT films were investigated to improve their thermoelectric properties. The morphology and Raman spectroscopy of the PEDOT films were analyzed according to their applied potential and deposition time. The best thermoelectric properties were found in films grown at 1.3 V for 10 min, with an electrical conductivity of 158 ± 8 S/cm, a Seebeck coefficient of 33 ± 1 µV/K, and a power factor of 17 ± 2 µW/K·m2. This power factor value is three times higher than the value reported in the literature for electropolymerized PEDOT films in acetonitrile using lithium perchlorate as a counter-ion. The thermal conductivity was found to be (1.3 ± 0.3) × 10−1 W/m·K. The highest figure of merit obtained at room temperature was (3.9 ± 1.0) × 10−2 using lithium perchlorate as a counter-ion. In addition, three-dimensional (3D) PEDOT nanonetworks were electropolymerized inside 3D anodic aluminum oxide (3D AAO), obtaining lower values in their thermoelectric properties., The authors acknowledge financial support from PID2020-118430GB-I00 and CSIC PIF 2D-MESES. Cristina V. Manzano and Aída Serrano acknowledge funding from Atracción de Talento Investigador de la Comunidad de Madrid, contracts no. 2019-T1/IND-13541 and 2017-t2/IND5395, respectively. O.C.C. acknowledges to micro-TENERGY project from the Ramon Areces’ Foundation. We acknowledge the services of the MiNa Laboratory at IMN and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794) and the EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Interconnected three-dimensional anodized aluminum oxide (3D-AAO) metamaterials using different waveforms and metal layers for RGB display technology applications

  • Manzano, Cristina V.
  • Rodríguez-Acevedo, Julia
  • Caballero-Calero, Olga
  • Martín-González, Marisol
Research into the artificial reproduction of vibrant colours in natural creatures and the reproduction of their structural colours has generated considerable interest. One inorganic material that has been studied for the generation of these artificial colours is anodic aluminium oxide (AAO). For example, 3D anodic aluminium oxide (3D-AAO) metamaterials act as distributed Bragg reflectors. This study examines the effect of the application of various waves (square, sinusoidal, and sawtooth) during the generation of 3D-AAO on the optical and morphological properties of these 3D metamaterials. The effect of the waveform in the colours and hues has been explained by a theoretical model. Furthermore, the work analyses how colour can be improved by depositing a thin metal layer on top, obtaining, from a simplistic point of view, a combination of two effects: a Bragg reflector (3D-AAO) and an optical reflector (metal mirror). For that, different metals like Au, Pt, and Cr have been studied. The thickness of the metal layer has been theoretically modelled. This study paves the way for a new approach to developing structural colours for their use in for example RGB display technologies. This journal is, M. S. M. G. wants to acknowledge the MINECO project PID2020- 118430GB-100 and Intramural 2D-MESES 201950E057. C. V. M. acknowledges financial support from ‘‘Atracción de Talento Investigador’’ de la Comunidad de Madrid, contract 2019-T1/ IND-13541. We would like to acknowledge Adria´n Isaac Pe´rez Barroso for the development of LabVIEW and MatLab programs to control the pulsed anodization with different waves. We acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (Project SpaceTec, S2013/ICE2822), MINECO (Project CSIC13-4E-1794) and EU (FEDER, FSE). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Nickel three-dimensional Nano-Networks with a single transversal channel interconnexions plane: Magnetization reversal experiments and simulations

  • Sanz González, Ruy
  • Ruiz-Clavijo, Alejandra
  • Navas, David
  • Ordoñez Cencerrado, Amanda
  • Caballero-Calero, Olga
  • Martín-González, Marisol
Resumen del trabajo presentado en la XIII European Magnetic Sensors and Actuators Conference (EMSA 2022), celebrada en Madrid (España), del 5 al 8 de julio de 2022, Understanding the interactions between magnetic nanostructures is one of the most important factors in predicting and controlling the advanced functionalities of Three-Dimensional (3D) integrated magnetic nanostructures1 . In this work, we focus on interconnected Ni nanowires forming a controlled 3D magnetic nanonetworks2,3. This type of system exhibits striking anisotropic magnetic responses3 and interaction between nanowires. To understand their collective magnetic behavior, we studied the magnetization reversal processes in the 3D-nanonetworks composed of 55/65 nm diameter/distance nickel nanowires with a single interconnection between all the nanowires at 480 nm from the top surface (Fig. 1 a). We have characterized the system at different angles using first magnetization curves, hysteresis loops, and First Order Reversal Curves techniques (Fig. 1 b), which provided information about the key features that enable macroscopic tuning of the properties of the 3D magnetic nanonetwork. In addition, micromagnetic simulations (Fig. 1 c) provided and accurate modeling of the magnetic response of the system. The results revealed important and intense anisotropic magnetic interactions. These interactions arise as capital for controlling the collective response of the system. The results pave the way for the design and realization of 3D novel metamaterials and sensors based on the nucleation and propagation of ferromagnetic domain walls, We acknowledge PID2020-118430GB-100, PID2019-108075RB-C31, PID2020-115325GB-C31 and RYC-2017-22820 funded by MCIN/AEI/ 10.13039/501100011033 and Intramural 2D-MESES 201950E057 founded by CSIC.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Plasmon-phonon interaction effects on the magneto refractive response of spintronic-plasmonic/dielectric structures

  • Armelles Reig, Gaspar
  • Cebollada, Alfonso
  • Álvaro Bruna, Raquel
We study the electromagnetic interactions and the magnetic modulation of the optical response of resonant spintronic-plasmonic structures coupled to a dielectric. The resonant nature of the spintronic system is provided by arrays of slits whose localized plasmon resonance interacts with the phonon band of the dielectric located in the mid infrared spectral range. This interaction can be tuned by changing the length of the slits and the thickness of the dielectric. In addition, the electromagnetic interaction also endorses with magnetic modulation capabilities to the phonon band, originating from a non-ferromagnetic material., Ministerio de Economía y Competitividad (FIS2015−72035−EXP, MAT 2014–58860-P, MAT2017−84009−R, PID2020-11843GB-100); Comunidad de Madrid (SINOXPHOS−CM (S2018/BAA-4403))
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermoelectric generators as an alternative for reliable powering of wearable devices with wasted heat

  • Martín-González, Marisol
  • Caballero-Calero, Olga
Everyday life relies heavily on electricity, which is also the foundation of innumerable other uses. Therefore, a continual study is required to enhance current ways or discover new ones for boosting power generation. One well-known and widely used method of generating electricity is the thermoelectric generator (TEG), which employs the Seebeck effect to transform waste energy into electrical energy. A TEG can be used whenever there is a temperature differential since the Seebeck effect allows temperature change to be converted into electrical energy. The foundation of the TEG is presented in the current study, along with an analysis of the current state of the art on TEGs. The different TEG geometries and their associated issues are also presented in this study. The new TEG technologies and the difficulties they provide are also discussed in this paper., The authors would like to acknowledge the financial support from the projects PID2020-118430 ​GB-100 and the micro-TENERGY project from Ramon Areces' foundation., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unveiling the Complex Magnetization Reversal Process in 3D Nickel Nanowire Networks

  • Ruiz-Clavijo, Alejandra
  • Caballero-Calero, Olga
  • Navas, David
  • Ordoñez Cencerrado, Amanda
  • Blanco-Portals, Javier
  • Peiró, Francesca
  • Sanz González, Ruy
  • Martín-González, Marisol
Understanding the interactions among magnetic nanostructures is one of the key factors to predict and control the advanced functionalities of 3D integrated magnetic nanostructures. In this work, the focus is on different interconnected Ni nanowires forming an intricate, but controlled, and ordered magnetic system: Ni 3D Nanowire Networks (3DNNs). These self-ordered systems present striking anisotropic magnetic responses, depending on the interconnections’ position between nanowires. To understand their collective magnetic behavior, the magnetization reversal processes are studied within different Ni 3D Nanowire Networks compared to the 1D nanowire 1DNW array counterparts. The systems are characterized at different angles using first magnetization curves, hysteresis loops, and First Order Reversal Curves techniques, which provided information about the key features that enable macroscopic tuning of the magnetic properties of the 3D nanostructures. In addition, micromagnetic simulations endorse the experiments, providing accurate modeling of their magnetic behavior. The results reveal a plethora of magnetic interactions, neither evident nor intuitive, which are the main role players controlling the collective response of the system. The results pave the way for the design and realization of 3D novel metamaterials and devices based on the nucleation and propagation of ferromagnetic domain walls both in 3D self-ordered systems and future nano-lithographed devices., M.M.G. and O.C.C. acknowledge the financial support from the project PID2020-118430GB-100 (MICINN). J.B.P., and F.P. acknowledge the financial support from PID2019-106165GB-C21 (MICINN) and M. López-Haro and J.J. Calvino from the University of Cádiz for the acquisition of the electron tomography series. The authors also acknowledge the service from the X-SEM Laboratory at IMM, and funding from MINECO under project CSIC13-4E-1794 with support from the EU (FEDER, FSE). The authors acknowledge the support for simulation hardware from J.L. Mesa at INTA. D.N. acknowledges the financial support from the project PID2019-108075RB-C31 and the grant RYC-2017-22820 funded by MICINN/10.13039/501100011033 and by “ESF Investing in your future”.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanoscale heat transport analysis by scanning thermal microscopy: from calibration to high-resolution measurements

  • Vera Londoño, Liliana Patricia
  • Ruiz-Clavijo, Alejandra
  • Pérez Taborda, Jaime Andrés
  • Martín-González, Marisol
Scanning thermal microscopy (SThM) is a powerful technique for thermal characterization. However, one of the most challenging aspects of thermal characterization is obtaining quantitative information on thermal conductivity with nanoscale lateral resolution. We used this technique with the cross-point calibration method to obtain the thermal contact resistance, R, and thermal exchange radius, b, using thermo-resistive Pd/SiN probes. The cross-point curves correlate the dependence of R and b with the sample's thermal conductivity. We implemented a 3ω-SThM method in which reference samples with known thermal conductivity were used in the calibration and validation process to guarantee optimal working conditions. We achieved values of R = 0.94 × 10 ± 0.02 K W and b = 2.41 × 10 ± 0.02 m for samples with a low thermal conductivity (between 0.19 and 1.48 W m K). These results show a large improvement in spatial resolution over previously reported data for the Wollaston probes (where b ∼ 2.8 μm). Furthermore, the contact resistance with the Pd/SiN is ∼20× larger than reported for a Wollaston wire probe (with 0.45 × 10 K W). These thermal parameters were used to determine the unknown thermal conductivity of thermoelectric films of AgSe, AgSe, CuSe (smooth vs. rough surface), and BiTe, obtaining, in units of W m K, the values of 0.63 ± 0.07, 0.69 ± 0.15, 0.79 ± 0.03, 0.82 ± 0.04, and 0.93 ± 0.12, respectively. To the best of our knowledge, this is the first time these microfabricated probes have been calibrated using the cross-point method to perform quantitative thermal analysis with nanoscale resolution. Moreover, this work shows high-resolution thermal images of the V and V signals, which can offer relevant information on the material's heat dissipation., We want to acknowledge the MINECO project PID2020- 118430GB-100 for financial support. The authors acknowledge also the service from SEM for the MiNa Laboratory at IMN, and their funding CM (project SpaceTec, S2013/ICE2822), MINECO (Project CSIC13-4E-1794), and EU (FEDER, FSE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CoSb3-based skutterudite nanocomposites prepared by cold sintering process with enhanced thermoelectric properties

  • Serrano Rubio, Aída
  • Caballero-Calero, Olga
  • Granados-Miralles, Cecilia
  • Gorni, Giulio
  • Manzano, Cristina V.
  • Rull Bravo, Marta
  • Moure Arroyo, Alberto
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
[EN] We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb-based thermoelectric materials. CSP at 150 °C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %, which is increased to around 92 % after a post-annealing at temperatures ≥ 500 °C in Ar atmosphere. The reported CSP produces Te doped-CoSb nanocomposites with similar morphological and structural characteristics to the starting nanopowders obtained by ball milling in air atmosphere. The post-thermal treatment induces grain coalescence and grain growth, crystallite size growth as well as compositional changes in the nanocomposite, decreasing the amount of the main phase, CoSb, and increasing the weight of secondary phase, CoSb, up to a 30 wt% at 600 °C. Remarkably, the average valence for the Co, Sb and Te absorbing atoms is neither transformed by the sintering process nor by the subsequent heat treatment. The functional response of the sintered thermoelectric nanocomposites exhibits a maximum figure of merit of 0.12(3) at room temperature for the nanocomposites sintered by CSP with a subsequent post-annealing at 500 °C. This is mainly due to its low thermal conductivity in comparison with similar powders sintered by other approaches, and it is explained by the morphological and structural properties. These findings represent an attractive alternative for obtaining efficient thermoelectric skutterudites by a scalable and cost-effective route., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN) through the projects MAT2017-86540-C4-1-R, MAT2017-86540-C4-3-R, RTI2018-095303-A-C52, PID2020-114192RB-C41 and PID2020-118430GB-100. Part of these experiments were performed at the CLAESS-BL22 beamline at ALBA Synchrotron (Grant no. 2020094658) and in collaboration with ALBA staff. A.S. and C.V.M. acknowledge financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” Contract no. 2017-t2/IND5395 and 2019-t1/IND-13541, respectively. C.G.-M. acknowledges financial support from MICINN through the “Juan de la Cierva” program (FJC2018-035532-I). A.M. is indebted to MICINN for the “Ramón y Cajal” contract (RYC-2013-14436), which is co-financed with European Social Fund., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sputtering Codeposition and Metal-Induced Crystallization to Enhance the Power Factor of Nanocrystalline Silicon

  • Conca, Andres
  • Ferreiro-Vila, Elías
  • Cebollada, Alfonso
  • Martín-González, Marisol
The power factor of highly boron-doped nanocrystalline Si thin films with controlled doping concentration is investigated. We achieve a high degree of tuning of boron content with a charge carrier concentration from 1018 to 1021/cm3 and with the electrical conductivity by varying the boron magnetron power from 10 to 60 W while maintaining the power of a SiB source constant during codeposition from two independent sputtering sources. Along with the increase in the electrical conductivity with increased boron doping, we observe a steady decrease in the Seebeck coefficient from 500 to 100 μV/K. These values result in power factors that exhibit a marked maximum of 5 mW/K2m for a carrier concentration of around 1021/cm3 at room temperature. Temperature-dependent measurements up to 650 °C show, with increasing doping concentration, a change of the resistivity from a semiconducting to a metallic behavior and an increase of both Seebeck coefficient and power factor, with this last one peaking at 9.8 mW/K2m in the 350-550 °C temperature range. For higher concentrations, scanning electron microscopy and energy-dispersive X-ray spectroscopy show a partial segregation of boron on particles on the surface. These results exemplify the great advantage of sputtering codeposition methods to easily tune and optimize the thermoelectric performance in thin films, obtaining in our specific case highly competitive power factors in a simple and reliable manner., Financial support by the Ministerio de Ciencia e Innovación with the Merge Project (PID2020118430GB-I00) is acknowledged. Technical support by Raquel Álvaro Bruna is gratefully acknowledged. We acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (project S2018/ NMT-4291 TEC2SPACE), MINECO (project CSIC13-4E- 1794) and EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Performance and Relative Humidity Impact of Cellulose-Derivative Networks in All-Day Passive Radiative Cooling

  • Manzano, Cristina V.
  • Díaz-Lobo, Alba
  • Gil-García, Marta
  • Rodríguez de la Fuente, Óscar
  • Morales-Sabio, Ángel
  • Martín-González, Marisol
All-day passive daytime radiative coolers (PDRC) offer a promising solution for energy-free cooling of buildings and devices. This study investigates the use of various cellulose-derivative networks to achieve optimal and stable cooling performance. These results showed that the mixed cellulose ester network has a maximum solar reflectance of 97%. While cellulose acetate network has a maximum infrared emissivity of 96% in the atmospheric transparency window band, which is a near-perfect infrared emitter, the nitrocellulose network shows the highest cooling temperature, with a significant reduction of 14 °C from the ambient temperature and a power of 124 W·m−2 during the daytime and at night of 7.7 °C and 72.8 W·m−2. This study also analyzes the dampness's effect on the cooling performance of cellulose-derivative networks. The cooling performance of the nitrocellulose network drops ≈ 3 °C (from 14 to 11.3 °C) when the relative humidity of the day exceeds ≈ 30% is observed. These findings indicate that the capacity of a material to absorb water from the surrounding air significantly influences its performance as a passive cooler, primarily due to changes in its optical properties. This is an important insight, as it highlights the need to consider environmental factors like relative humidity and sample hydrophobicity for PDRC systems., C.V.M acknowledges financial support from “ERC Consolidator Grant No.101087974 COOLed” and from “Atracción de Talento Investigador” de la Comunidad de Madrid, contract 2019-T1/IND-13541. M.S.M.G acknowl-edge the MERGE project PID2020-118430GB-100. The authors acknowl-edge the service from the MiNa Laboratory at IMN, and funding from CM(project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794)and EU (FEDER, FSE). And the CSIC for the article processing charges., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Localization and Directionality of Surface Transport in Bi2Te3 Ordered 3D Nanonetworks

  • Ruiz-Clavijo, Alejandra
  • Pérez, Nicolás
  • Caballero-Calero, Olga
  • Blanco, Javier
  • Peiró, Francesca
  • Plana-Ruiz, Sergi
  • López-Haro, Miguel
  • Nielsch, Kornelius
  • Martín-González, Marisol
The resistance of an ordered 3D-Bi2Te3 nanowire nanonetwork was studied at low temperatures. Below 50 K the increase in resistance was found to be compatible with the Anderson model for localization, considering that conduction takes place in individual parallel channels across the whole sample. Angle-dependent magnetoresistance measurements showed a distinctive weak antilocalization characteristic with a double feature that we could associate with transport along two perpendicular directions, dictated by the spatial arrangement of the nanowires. The coherence length obtained from the Hikami-Larkin-Nagaoka model was about 700 nm across transversal nanowires, which corresponded to approximately 10 nanowire junctions. Along the individual nanowires, the coherence length was greatly reduced to about 100 nm. The observed localization effects could be the reason for the enhancement of the Seebeck coefficient observed in the 3D-Bi2Te3 nanowire nanonetwork compared to individual nanowires., The authors would like to acknowledge the financial supportfrom the projects ERC Adv. POWERbyU 101052603,PID2020-118430GB-100, and PID2019-106165GB-C21 (MI-CINN) and project 2D-MESES from CSIC. This work wasalso cofinanced by the 2014−2020 ERDF OperationalProgramme and the Department of Economy, Knowledge,Business and University of the Regional Government ofAndalusia, project reference no. FEDER-UCA18-107139. Theauthors would also like to acknowledge the service from theMiNa Laboratory at IMN, and its funding from CM (projectSpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and EU (FEDER, FSE). F.P. acknowledges the supportfrom ICREA Academia 2022 and 2021SGR00242, Generalitatde Catalunya., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Localization and Directionality of Surface Transport in Bi2Te3 Ordered 3D Nanonetworks [Dataset]

  • Ruiz-Clavijo, Alejandra
  • Pérez, Nicolás
  • Caballero-Calero, Olga
  • Blanco, Javier
  • Peiró, Francesca
  • Plana-Ruiz, Sergi
  • López-Haro, Miguel
  • Nielsch, Kornelius
  • Martín-González, Marisol
According to the open access nature and its exceptions in the datasets regulation of the Call ERC-2021-ADG, and having reflected the following statements in the Data Management Plan of such project (ID: 101052603; POWERbyU; ERC-2021-ADG), the authors of the data associated with this publication state the following: The datasets associated with this publication will be available upon request, due to these datasets being subjected to Intellectual Property Restrictions; requests by externals for the use of these datasets will be approved by the project coordinator. Please, contact Prof. Marisol Martín-González: marisol.martin@csic.es This modus operandi will remain in effect, at least until the end of the project., Nanowires are excellent model systems for investigating the effects of low dimensionality in materials. Controlling the diameter of the nanowires, and hence its surface-to-volume ratio, the presence or relevance of surface-related characteristics can be addressed. This is of particular interest in the case of topological insulators owing to electronic surface states (topologically protected) independent from bulk states. Tetradymite chalcogenides Bi2Te3, Bi2Se3, and Sb2Te3 are small band gap semiconductors with wide application in state-of-the-art Peltier cooling devices or thermoelectric power generators. They are also strong 3D-topological insulator, with topologically protected states predicted to appear on any free surface regardless of the crystallographic orientation. This Dataset is referring to the following study, in which the resistance of an ordered 3D-Bi2Te3 nanowire nanonetwork was studied at low temperatures. Below 50 K the increase in resistance was found to be compatible with the Anderson model for localization, considering that conduction takes place in individual parallel channels across the whole sample. Angle-dependent magnetoresistance measurements showed a distinctive weak antilocalization characteristic with a double feature that we could associate with transport along two perpendicular directions, dictated by the spatial arrangement of the nanowires. The coherence length obtained from the Hikami–Larkin–Nagaoka model was about 700 nm across transversal nanowires, which corresponded to approximately 10 nanowire junctions. Along the individual nanowires, the coherence length was greatly reduced to about 100 nm. The observed localization effects could be the reason for the enhancement of the Seebeck coefficient observed in the 3D-Bi2Te3 nanowire nanonetwork compared to individual nanowires., The authors would like to acknowledge the financial support from the projects ERC Adv. POWERbyU 101052603, PID2020-118430GB-100, and PID2019-106165GB-C21 (MICINN) and project 2D-MESES from CSIC. This work was also cofinanced by the 2014–2020 ERDF Operational Programme and the Department of Economy, Knowledge, Business and University of the Regional Government of Andalusia, project reference no. FEDER-UCA18-107139. The authors would also like to acknowledge the service from the MiNa Laboratory at IMN, and its funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and EU (FEDER, FSE). F.P. acknowledges the support from ICREA Academia 2022 and 2021SGR00242, Generalitat de Catalunya., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructured Metamaterials for the thermal and electromagnetic isolation of Cryostats

  • Vivas, Laura G.
  • Ramos, David
  • Martín-Rubio, Carolina
  • Rivelles, Alejandro
  • Madueño, Laura
  • Ruiz-Clavijo, Alejandra
  • Toledano-Díaz, Adolfo
  • Schneider, Marc
  • Plaza, Borja
  • Poyatos, David
  • Hoyo, Juan Carlos del
  • Caballero-Calero, Olga
  • Worgull, Matthias
  • Martín, Santiago
  • Martín, Boris
  • Maicas, Marco
  • Navas, David
  • Martín-González, Marisol
  • Sanz González, Ruy
Póster presentado en SPIE Astronomical Telescopes + Instrumentation, celebrado en Yokohama (Japón), del 16 al 21 de junio de 2024, In terms of thermal and electromagnetic isolation properties, Nanostructured Metamaterials may present important advantages compared to current employed materials. In this work, we present the synthesis routes and the preliminary characterization results of some metamaterials based on Poly-ether-ether-ketone and nanostructured anodic oxides, with low thermal conductivity, combined with Au nanocolumns and three-dimensional nanonetworks. The results reveals proper magnetic and electromagnetic properties and suggest their suitable use under vacuum and cryogenic conditions., Grants PID2020-115325GB-C31, PID2020-117024GB-C42 and PID2020-118430GB100 funded by MCIN/AEI/ 10.13039/501100011033, Karlsruhe Nano Micro Facility (KNMF), a Helmholtz Research Infrastructure at the Karlsruhe Institute of Technology, and European Union by MSCA project MIDAS Grant 101107507., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermoelectric bismuth telluride nanostructures fabricated by electrodeposition within flexible templates

  • Cerviño Solana, Pablo
  • Ramírez-Peral, María Jesús
  • Martín-González, Marisol
  • Caballero-Calero, Olga
Bismuth telluride, a highly efficient thermoelectric material, stands out for applications around room temperature in wearable devices. By harnessing the thermal gradient established between the human body and ambient temperature, we can generate useable electricity. Notably, bismuth telluride nanostructures exhibit significantly lower thermal conductivities compared to their bulk counterparts. As a result, the thermoelectric efficiency achieved is notably higher. Our research focuses on developing efficient nanostructured materials based on bismuth telluride inside a flexible substrate made of polyester. We employ scalable methods, such as template-assisted electrochemical deposition, to fabricate these nanostructures. In this study, we present an approach to the development of flexible nanostructured thermoelectric materials. Despite using a reduced quantity of active material, our electrochemically deposited nanostructures inside a flexible template demonstrate a remarkable performance. They exhibit 24 % of the Power Factor reported for conventional electrochemically fabricated Bi2Te3 thin films, and notably, they even surpass the Power Factor reported for flexible Bi2Te3-based inks used in the creation of flexible generators. This achievement underscores the potential of our method in the advancement of efficient, flexible thermoelectric devices., This work has been supported by the Ramon Areces Foundation through the micro-TENERGY project. The authors would like to acknowledge the service from the MiNa Laboratory at IMN, and its funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and EU (FEDER, FSE). We also acknowledge the funding by the MINECO under grant number PID2020-118430 GB-100. O.C–C would also like to acknowledge fruitful discussions with David López Romero and the assistance with the SEM microscope from Raquel Álvaro Bruna., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polylactic acid 3D interconnected nanonetworks as high reflectance distributed Bragg reflectors

  • Resende, Pedro M.
  • Martín-González, Marisol
Natural systems found ways to exploit light at the nanoscale, devising complex 3D structures that behave as photonic crystals, able to produce structural coloration. Distributed Bragg reflectors are a particular example of 1D photonic crystals, used in different applications, including structural coloration. Currently distributed Bragg reflectors rely on multi-material deposition or material doping to achieve high refractive index contrast, unlike the biological counterparts that often rely on single-materials through structural variations. In this work, we report single-material polymeric distributed Bragg reflectors fabricated from the infiltration of polylactic acid into 3D anodic aluminium oxide templates. These templates act as sacrificial scaffolds for the nanostructuration of the polymeric material, generating a 3D polymer network with periodic modulations. The obtained structures present very high reflectance, above 95%, with a low number of periods around 20 repeating layers. These structures offer a new approach to the generation of flexible single-material DBRs with high reflectance, an important issue in all-polymer photonic systems., M. S. M. G wants to acknowledge the MINECO project PID2020- 118430GB-100 for financial support. The authors acknowledge also the service from the MiNa Laboratory at IMN, and funding CM (project SpaceTec, S2013/ICE2822), MINECO (Project CSIC13-4E-1794), and EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Shedding Light on the Mid-Infrared Complex Refractive Index of Anodic Aluminum Oxide

  • Díaz-Lobo, Alba
  • Castro-Fernández, Irene
  • Blanco, Eduardo
  • Ramos Vega, Daniel
  • Martín-González, Marisol
  • Manzano, Cristina V.
In the current scientific landscape, the understanding of optical properties in the mid-infrared (mid-IR) range (3–30 µm) is crucial in simulations and models to explore the potential of materials for various applications. However, due to the challenges associated with mid-IR characterization, accurate refractive index (n) and extinction coefficient (κ) data are often lacking in the literature. This study addresses this gap by investigating the mid-IR n and κ spectra of anodic aluminum oxide (AAO) nanostructures anodized under different conditions, using two distinct approaches: IR ellipsometry and a theoretical model based on multilayer reflection and effective medium. The results demonstrate a strong agreement: the anodizing conditions have a significant influence on the optical properties of the AAO nanostructures. These differences enable accurate simulations of the emissivity spectra of AAO nanostructures on Al foils, which align closely with experimental measurements. This theoretical approximation is versatile and extensible to a broad range of materials. Different materials are tested, namely, a sapphire, a polycarbonate film, and a polyethylene terephthalate (PET) film achieving a useful qualitative description. This study paves the way for a novel approach in the engineering of new micro and nano-optical materials, facilitating their evaluation for suitability in mid-IR applications., C.V.M. acknowledges financial support from “Atracción de Talento Investigador” de la Comunidad de Madrid, contract 2019-T1/IND-13541. The authors acknowledge the service from the MiNa Laboratory at IMN, and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and EU (FEDER, FSE). This study was partially supported by the Spanish Ministry of Science under project OMNIPATH (reference PID2020-119587RB-I00. I.C. acknowledges the funded by Formación de Profesorado Universitario (FPU) grant from the Spanish Ministry of Universities, reference FPU21/03180. M.M.G. acknowledged the Ministerio de Ciencia e Innovación with the Merge Project (PID2020118430GB-I00). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

∼5-Fold enhancement in the thermoelectric figure of merit of sustainable 3D-CuNi interconnected nanonetworks due to ultralow lattice thermal conductivity

  • Manzano, Cristina V.
  • Caballero-Calero, Olga
  • Casari, Daniele
  • Sharma, Amit
  • Díaz-Lobo, Alba
  • Maeder, Xavier
  • Martín-González, Marisol
The pursuit of efficient thermoelectric materials, particularly those composed of low-toxicity and Earth-abundant elements, has intensified in recent years. This study introduces an approach to increase the thermoelectric properties of CuNi alloys through the synergistic application of two nanostructuring techniques: the incorporation of saccharine into the electrolyte to achieve a crystallite size reduction to 23-26 nm and the utilization of three-dimensional (3D) anodic aluminum oxide (3D-AAO) templates to fabricate nanowire networks. For comparison purposes, we successfully electrodeposited CuNi films, one-dimensional (1D) nanowire arrays, and modulated nanowire arrays, together with 3D-nanonetworks, maintaining a consistent composition of Cu0.60Ni0.40 across all samples. Notably, while the electrical conductivity and Seebeck coefficient remained consistent between the nanocrystalline CuNi films and the 3D-nanonetworks, a significant reduction in thermal conductivity was observed, decreasing from 29 W m-1 K-1 for the bulk material to 10.9 ± 1.1 W m-1 K-1 for nanocrystalline films, to 5.3 ± 0.5 W m-1 K-1 for the 3D nanonetworks, and to 4.9 ± 0.6 W m-1 K-1 for free-standing 3D CuNi nanonetworks. This reduction is attributed to enhanced phonon scattering within the 3D architecture together with the nanocrystalline size inside the nanowires. The figure of merit (zT) exhibited an impressive increase of more than four times (4.4) for 3D-CuNi nanonetworks within AAO templates and 4.8 times for free-standing 3D-CuNi nanonetworks, when compared to bulk. Our findings underscore the potential of dual nanostructuring strategies to optimize the thermoelectric performance of environmentally friendly, stable, and abundant materials like CuNi, paving the way for advancements in sustainable energy technologies., The authors would like to acknowledge financial support from MINECO under grant number PID2020-118430GB-100. C. V. M. acknowledges financial support from “Atracción de Talento Investigador” de la Comunidad de Madrid, contract 2019-T1/IND-13541. We acknowledge the service from the MiNa Laboratory at IMN and funding from CM (project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794), and EU (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Nanostructured Metamaterials for the thermal and electromagnetic isolation of Cryostats [Dataset]

  • Vivas, Laura G.
  • Ramos, David
  • Martín-Rubio, Carolina
  • Rivelles, Alejandro
  • Madueño, Laura
  • Ruiz-Clavijo, Alejandra
  • Toledano-Díaz, Adolfo
  • Schneider, Marc
  • Plaza, Borja
  • Poyatos, David
  • Hoyo, Juan Carlos del
  • Caballero-Calero, Olga
  • Worgull, Matthias
  • Martín, Santiago
  • Martín, Boris
  • Maicas, Marco
  • Navas, David
  • Martín-González, Marisol
  • Sanz González, Ruy
According to the open access nature and its exceptions in the datasets regulation of the Call HORIZON-MSCA-2022-PF-01, and having reflected the following statements in the Data Management Plan of such project (ID: 101107507; MIDAS; MSCA Postdoctoral Fellowship), the authors of the data associated with this publication state the following: The datasets associated with this publication will be available upon request, due to these datasets being subjected to Intellectual Property Restrictions; requests by externals for the use of these datasets will be approved by the principal investigators of the project Laura G. Vivas and Marisol Martin. Please, contact Dr. Laura G. Vivas and Prof. Martín-Gonzalez: laura.g.vivas@csic.es and marisol.martin@csic.es This modus operandi will remain in effect, at least until the end of the project., In terms of thermal and electromagnetic isolation properties, Nanostructured Metamaterials may present important advantages compared to current employed materials. This Dataset refers to a work in which we present the synthesis routes and the preliminary characterization results of some metamaterials based on Poly-ether-ether-ketone and nanostructured anodic oxides, with low thermal conductivity, combined with Au nanocolumns and three-dimensional nanonetworks. The results reveals proper magnetic and electromagnetic properties and suggest their suitable use under vacuum and cryogenic conditions., This work was supported by: Karlsruhe Nano Micro Facility (KNMF), a Helmholtz Research Infrastructure at the Karlsruhe Institute of Technology, European Union (MSCA project MIDAS Grant 101107507) and grants PID2020 115325GB-C31, PID2020-117024GB-C42 and PID2020-118430GB-100 funded by MCIN/AEI/10.13039/501100011033, Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

3D BiTe Interconnected Nanowire Networks to Increase Thermoelectric Efficiency

  • Ruiz-Clavijo, Alejandra
  • Caballero-Calero, Olga
  • Manzano, Cristina V.|||0000-0001-5708-6544
  • Maeder, Xavier
  • Beardo, Albert|||0000-0003-1889-1588
  • Cartoixà, Xavier|||0000-0003-1905-5979
  • Alvarez, F. Xavier|||0000-0001-6746-2144
  • Martín-González, Marisol|||0000-0002-5687-3674
3D interconnected nanowire scaffoldings are shown to increase the thermoelectric efficiency in comparison to similar diameter 1D nanowires and films grown under similar electrodeposition conditions. BiTe 3D nanonetworks offer a reduction in thermal conductivity (κ) while preserving the high electrical conductivity of the films. The reduction in κ is modeled using the hydrodynamic heat transport equation, and it can be understood as a heat viscosity effect due to the 3D nanostructuration. In addition, the Seebeck coefficient is twice that of nanowires and films, and up to 50% higher than in a single crystal. This increase is interpreted as a nonequilibrium effect that the geometry of the structure induces on the distribution function of the phonons, producing an enhanced phonon drag. These thermoelectric metamaterials have higher performance and are fabricated with large areas by a cost-effective method, which makes them suitable for up-scale production.