Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A large-eddy simulation of diesel-like gas jets

  • Hoyas, Sergio|||0000-0002-8458-7288
  • Gil, A.|||0000-0001-7192-6992
  • Mompó Laborda, Juan Manuel
  • Khuong ., Anh Dung
[EN] Some aspects of the transient evolution of diesel-like gas jets by means of large-eddy simulation (LES) are discussed in this work. In order to understand the relationship between the inlet boundary condition and the development of the turbulent motions of the diesel sprays, a 3D injection chamber is simulated. The main assumption of the setup is the turbulent gas jet theory hypothesis applied to the inlet boundary conditions. Validation of the results is achieved by comparing with both experimental diesel spray measurements and trusted Reynolds-averaged Navier-Stokes (RANS) simulations. Results show that reasonable simulation of turbulent patterns from one diameter distant from the inlet boundary condition is achieved. Copyright © 2011 Inderscience Enterprises Ltd., This research has been funded by the Spanish Government in the frame of the Project ‘Métodos LES para la simulación de chorros multifásicos’, Ref. ENE2010-18542. The authors also acknowledge the financial support of the Universidad Politécnica de Valencia under the contract Reference PAID-2759 and the Generalitat Valenciana, under the contract GV/2010/039. We are also grateful to Dr. Franciso Javier Salvador and Dr. José Manuel Pastor for providing experimental data and fruitful advices. In addition, we gratefully acknowledge helpful discussions with many researchers in CMT-Motóres Térmicos, especially Ms. Palma González and Ms. Mariany Chávez.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A moving mesh generation strategy for solving an injector internal flow problem

  • Margot , Xandra|||0000-0002-2639-0444
  • Hoyas, Sergio|||0000-0002-8458-7288
  • Fajardo, Pablo
  • Patouna, Stavroula
[EN] The ability to handle complex geometries is an important part of transient calculations; therefore, the need for fully automatic mesh generation capable of dealing with such geometries is quite demanded. In this paper a specific approach to fully automatic three-dimensional mesh generation is presented. An approach to moving the generated mesh is also outlined. In particular, the simulation of a diesel injector needle movement is sought. The movement of the needle was calculated on the basis of injection rate experimental data and injection rate predicted data with steady state boundaries and geometry. The simulation was performed using the commercial code STAR-CD version 4.06. (C) 2010 Elsevier Ltd. All rights reserved., This research was funded by the Spanish Government in the framework of the Project "Caracterizacion experimental de la cavitacion en el flujo interno e influencia sobre modelos de chorro Diesel'', Reference TRA2007-68006-C02-01. SH and PF were partially supported by the Universidad Politecnica de Valencia under the program "Primeros Proyectos de investigacion'', in the framework of the project "Simulacion CFD de chorros Diesel en inyeccion directa: la atomizacion primaria'', Reference PAID-2759.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

CFD Study of Needle Motion Influence on the Spray Conditions of Single-Hole Injectors

  • Margot , Xandra|||0000-0002-2639-0444
  • Hoyas, Sergio|||0000-0002-8458-7288
  • Fajardo, Pablo
  • Patouna, Stavroula
[EN] The spray characteristics and, consequently, the success of the Diesel combustion process is strongly affected by the manner in which fuel is introduced in the combustion chamber. This work consists in studying the effect of needle motion of typical single-hole sac-type injectors on nozzle exit conditions. Three-dimensional moving mesh simulations have been carried out to calculate the injection process using cylindrical and conical nozzle geometries. The CFD analysis includes a study of the effect of cavitation on kinetic turbulent energy and velocity profiles. Results show that the flow within the nozzle and at the exit varies depending on the nozzle geometry and needle position. The model predicts clouds of cavitation that grow and exit the nozzle at low needle lifts. A kind of hysteresis in the development of the flow has also been observed between needle opening and closing. The existing correlation between turbulence and cavitation at the nozzle hole exit during the needle motion has been quantified, This research has been funded by the Spanish Government in the frame of the Project "Caracterizacion experimental de la cavitacion en el flujo interno e influencia sobre modelos de chorro Diesel," Reference TRA2007-68006-C02-01. S.H. and P.F. were partially supported by the Universidad Politecnica de Valencia under the program "Primeros Proyectos de investigacion," in the frame of the project "Simulacion CFD de chorros Diesel en inyeccion directa: la atomizacion primaria," Reference PAID-2759 and by the Generalitat Valenciana under Contract No. GV/2010/039.