Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A moving mesh generation strategy for solving an injector internal flow problem

  • Margot , Xandra|||0000-0002-2639-0444
  • Hoyas, Sergio|||0000-0002-8458-7288
  • Fajardo, Pablo
  • Patouna, Stavroula
[EN] The ability to handle complex geometries is an important part of transient calculations; therefore, the need for fully automatic mesh generation capable of dealing with such geometries is quite demanded. In this paper a specific approach to fully automatic three-dimensional mesh generation is presented. An approach to moving the generated mesh is also outlined. In particular, the simulation of a diesel injector needle movement is sought. The movement of the needle was calculated on the basis of injection rate experimental data and injection rate predicted data with steady state boundaries and geometry. The simulation was performed using the commercial code STAR-CD version 4.06. (C) 2010 Elsevier Ltd. All rights reserved., This research was funded by the Spanish Government in the framework of the Project "Caracterizacion experimental de la cavitacion en el flujo interno e influencia sobre modelos de chorro Diesel'', Reference TRA2007-68006-C02-01. SH and PF were partially supported by the Universidad Politecnica de Valencia under the program "Primeros Proyectos de investigacion'', in the framework of the project "Simulacion CFD de chorros Diesel en inyeccion directa: la atomizacion primaria'', Reference PAID-2759.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

CFD Study of Needle Motion Influence on the Spray Conditions of Single-Hole Injectors

  • Margot , Xandra|||0000-0002-2639-0444
  • Hoyas, Sergio|||0000-0002-8458-7288
  • Fajardo, Pablo
  • Patouna, Stavroula
[EN] The spray characteristics and, consequently, the success of the Diesel combustion process is strongly affected by the manner in which fuel is introduced in the combustion chamber. This work consists in studying the effect of needle motion of typical single-hole sac-type injectors on nozzle exit conditions. Three-dimensional moving mesh simulations have been carried out to calculate the injection process using cylindrical and conical nozzle geometries. The CFD analysis includes a study of the effect of cavitation on kinetic turbulent energy and velocity profiles. Results show that the flow within the nozzle and at the exit varies depending on the nozzle geometry and needle position. The model predicts clouds of cavitation that grow and exit the nozzle at low needle lifts. A kind of hysteresis in the development of the flow has also been observed between needle opening and closing. The existing correlation between turbulence and cavitation at the nozzle hole exit during the needle motion has been quantified, This research has been funded by the Spanish Government in the frame of the Project "Caracterizacion experimental de la cavitacion en el flujo interno e influencia sobre modelos de chorro Diesel," Reference TRA2007-68006-C02-01. S.H. and P.F. were partially supported by the Universidad Politecnica de Valencia under the program "Primeros Proyectos de investigacion," in the frame of the project "Simulacion CFD de chorros Diesel en inyeccion directa: la atomizacion primaria," Reference PAID-2759 and by the Generalitat Valenciana under Contract No. GV/2010/039.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A combined 1D3D CFD approach for reducing mesh dependency in Diesel spray calculations

  • García-Oliver, José M|||0000-0002-2676-9681
  • Margot , Xandra|||0000-0002-2639-0444
  • Chávez Cobo, Mariany de Jesús
  • Karlsson, A
[EN] A 1D3D-CFD coupled spray model is proposed in this work for the simulation of Diesel sprays under non-evaporative conditions and constant injection velocity in time. The basic idea of the model is to reduce the poor estimations of the gas velocity and droplets/gas relative velocity obtained with the standard 3D-CFD Eulerian-Lagrangian spray model, when coarse meshes are used. The coupling has been achieved in the calculation of the momentum source interaction term. General considerations, descriptions and implementation of the model in a commercial CFD code are outlined. Diesel spray simulations performed using the proposed approach have been compared with those obtained with the standard 3D-CFD, 1D models and experimental data. Encouraging results were found in terms of spray evolution when changing meshes and ambient conditions. © 2011 Elsevier Ltd., This work has been founded by Universidad Politecnica de Valencia UPV under the FPI-UPV program and the public project TRA2007-68006-C02-01, from MICINN (Spain). Special thanks are extended to Dr. S. Hoyas and Dr. J.M. Pastor and Dr. M. Balthasar for the support and motivation.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Flow regime effects on non-cavitating injection nozzles over spray behaviour

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
[EN] This paper deals with the influence of flow regime (laminar, transition or turbulent) on the internal flow behavior, and how it affects the spray development in diesel nozzles. In particular, the research described here aims at studying and quantifying the internal flow regime effects on the spray behavior. With this purpose, internal flow results, based on mass flow rate and momentum flux measurements performed on three different tapered nozzles and which helped to determine the flow regime, has been taken into account as a point of departure for the spray behavior analysis. Thus, in this work, spray macroscopic visualization tests have been performed and analyzed which clearly revealed a change in the behavior of the angle and penetration of the spray related to the change of the flow nature. Moreover, with all the experimental data available, it has been possible to relate macroscopic parameters of the spray with those describing the internal flow (momentum and effective velocity) or the geometry of the nozzle (length or diameter) through correlations. © 2010 Elsevier Inc., This research has been funded in the frame of the Project “Caracterización experimental de la cavitación en el flujo interno e influencia sobre modelos de chorro diésel”, Reference TRA2007-68006-C02-01, from MINISTERIO DE CIENCIA E INNOVACIÓN from Spain. The authors thank José Enrique del Rey for his collaboration in the experimental measurements.