Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 57
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Energy profiling of FPGA-based PHY-layer building blocks encountered in modern wireless communication systems

  • Bartzoudis, Nikolaos
  • Font Bach, Oriol
  • Payaro, M.
  • Pascual Iserte, Antonio
  • Rubio, Javier
  • García-Fernández, Juan José
  • García-Armada, Ana
Proceeding at: IEEE 8th Sensor Array and Multichannel Signal Processing Workshop (SAM), took place 2014, Jun, 22-25 in Coruña (españa). The event web site of http://www.gtec.udc.es/sam2014/ ., Characterizing the energy cost of different physical (PHY) layer building blocks is becoming increasingly important in modern cellular-based communications, considering the cross sector requirements for performance enhancements and energy savings. This paper presents energy profiling metrics of different PHY-layer FPGA implementations encountered in modern wireless communication systems. The results give an insight of the distribution of the consumed energy in different baseband building blocks or configurations before and after applying power optimizations in the FPGA design and implementation., This work was partially supported by: the Spanish Government under projects TEC2011-29006-C03-01 (GRE3N-PHY), TEC2011-29006-C03-02 (GRE3N-LINKMAC) and TEC2011-29006-C03-03 (GRE3N-SYST); and the European Commission under project NEWCOM# (GA 318306)., Publicado
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Assessment of RSS model calibration with real WLAN devices

  • Castro, Juan Manuel
  • Moragrega, Ana
  • Closas, Pau
  • Fernández Rubio, Juan Antonio|||0000-0003-1494-5366
Received Signal Strength (RSS) for indoor localization is widely used due to its simplicity and availability in most mobile devices. The RSS channel model is defined by the propagation losses and the shadow fading. This paper studies two-slope RSS channel model and compares its validity to classical one-slope path loss model. Particularly, the work presents real-data results of a Bayesian calibration method. Validation of the model fitting is then performed in a dynamic scenario where the distance to a reference node is tracked by a Kalman Filter. Results show the superiority of two-slope model, specially at large distances., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Joint optimization of power and data transfer in multiuser MIMO systems

  • Rubio López, Javier
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
  • Palomar, Daniel P.
  • Goldsmith, Andrea
We present an approach to solve the nonconvex optimization problem that arises when designing the transmit covariance matrices in multiuser multiple-input multiple-output (MIMO) broadcast networks implementing simultaneous wireless information and power transfer (SWIPT). The MIMO SWIPT problem is formulated as a general multiobjective optimization problem, in which data rates and harvested powers are optimized simultaneously. Two different approaches are applied to reformulate the (nonconvex) multiobjective problem. In the first approach, the transmitter can control the specific amount of power to be harvested by power transfer whereas in the second approach the transmitter can only control the proportion of power to be harvested among the different harvesting users. We solve the resulting formulations using the majorization-minimization (MM) approach. The solution obtained from the MM approach is compared to the classical block-diagonalization (BD) strategy, typically used to solve the nonconvex multiuser MIMO network by forcing no interference among users. Simulation results show that the proposed approach improves over the BD approach both the system sum rate and the power harvested by users. Additionally, the computational times needed for convergence of the proposed methods are much lower than the ones required for classical gradient-based approaches., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Sparse multiple relay selection for network beamforming with individual power constraints using semidefinite relaxation

  • Blanco, Luis
  • Nájar Martón, Montserrat|||0000-0003-3507-5689
This paper deals with the multiple relay selection problem in two-hop wireless cooperative networks with individual power constraints at the relays. In particular, it addresses the problem of selecting the best subset of K cooperative nodes and their corresponding beamforming weights so that the signal-to-noise ratio (SNR) is maximized at the destination. This problem is computationally demanding and requires an exhaustive search over all the possible combinations. In order to reduce the complexity, a new suboptimal method is proposed. This technique exhibits a near-optimal performance with a computational burden that is far less than the one needed in the combinatorial search. The proposed method is based on the use of the l1-norm squared and the Charnes-Cooper transformation and naturally leads to a semidefinite programming relaxation with an affordable computational cost. Contrary to other approaches in the literature, the technique exposed herein is based on the knowledge of the second-order statistics of the channels and the relays are not limited to cooperate with full power., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A margin adaptive scheduling algorithm for FBMC/OQAM systems

  • Caus López, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
  • Moretti, Marco
  • Kliks, Adrian
This paper addresses the margin adaptive problem for the filter bank multicarrier (FBMC) modulation based on the offset QAM (OQAM), referred to as FBMC/OQAM. The analysis conducted in this paper reveals that due to the specific FBMC/OQAM transmission format the system has to deal with inter-user, inter-symbol and inter-carrier interference to solve the resource allocation problem. To manage the interference, the successive channel allocation method, originally proposed for the orthogonal frequency division multiplexing (OFDM), has been modified by organizing subcarriers in groups and assigning subcarriers to users in a block-wise fashion. Following this strategy and making some approximations we demonstrate that it is possible to pose a single problem that is valid for OFDM and FBMC/OQAM. In this case, numerical results show that FBMC/OQAM is more energy-efficient than OFDM because it requires less power to transmit the same information rate.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Energy consumption optimisation for duty-cycled schemes in shadowed environments

  • Predojev, Tatjana
  • Alonso-Zárate, Jesús
  • Dohler, Mischa
  • Alonso Zárate, Luis Gonzaga|||0000-0002-6608-0862
The focus of this study is the optimal configuration of a wireless low-power duty-cycled network with respect to the minimal energy consumption. Precisely, the energy consumption of a truncated-ARQ scheme in realistic shadowing environments is examined for the reference IEEE 802.15.4e standard protocol and for its cooperative extension that is presented in the paper. We show how to choose between the direct or multihop forwarding and the cooperative version of the two. We determine the optimal forwarding strategy for both loose and strict reliability requirements. Low-power links are parametrised by the interdevice distance and the corresponding outage probability, for the fixed output transmission power. It is shown that significant amounts of energy can be saved when the most adequate scheme of the three is applied. All analytical results are validated in the network simulator ns-3., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Device-to-device communications and small cells: enabling spectrum reuse for dense networks

  • Laya, Andrés
  • Wang, Kun
  • Ahmed, Ashraf Awadelkarim Widaa
  • Alonso Zárate, Jesús
  • Markendhal, Jan
  • Alonso Zárate, Luis Gonzaga|||0000-0002-6608-0862
In the evolution of communication networks, there has always been a need to increase the capacity to cope with the continuous growing demand for data transmission. However, with the arrival of the Internet-of-Things and the commoditization of broadband access through smartphones, tablets, smart-watches, and all types of connecting devices, future networks must be capable of providing higher bandwidth and Quality of Experience, as wellas operating in dense networks with a massive number of simultaneous connections. This high number of connections will be very heterogeneous, spanning from highly-demanding data rate applications to low-complexity and high energy-efficient Machine-to-Machine communications. In such a dense and complex scenario, a more flexible use of spectrum resources is deemed to be the way to meet the growing requirements for data transmission. In particular, this article focuses on Device-to-Device communications and small cell deployments as emerging facilitators of such a demanding and heterogeneous scenario. The pros and cons of both complementary strategies are identified from both a technical and a business point of view, and main standardization activities are discussed. The aim of this article is to identify and describe open challenges and to inspire new areas for research that make viable the next generation of dense networks., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Spatial sparsity based direct positioning for IR-UWB in IEEE 802.15.4a channels

  • Lagunas Targarona, Eva|||0000-0002-9936-7245
  • Navarro, Mònica
  • Closas Gómez, Pau
  • Nájar Martón, Montserrat|||0000-0003-3507-5689
In this paper, we focus on the application of Compressive Sensing (CS) techniques to Impulse Radio (IR) Ultra-WideBand (UWB) positioning systems under indoor propagation environments. Direct Position Estimation (DPE) approaches can potentially improve the position estimation accuracy of conventional two-step techniques by directly estimating the position coordinates from the observed signal in a single step. Furthermore, DPE does not require a threshold selection upon which accuracy of two-step approaches depend on. Although in the presence of multipath the actual gains are not straight forward, recent evaluation of DPE positioning in IR-UWB system proved accurate positioning estimate gains. However it comes at a cost of higher computational complexity. This paper exploits the sparseness of the problem to reduce the computational load of the positioning estimation process and relax the requirements of the Analog to Digital Converter (ADC) when sampling UWB signals. Based on the fact that the number of unknown targets is small in the discrete spatial domain, this paper incorporates the multiple location hypotheses into an overcomplete basis, which highlights the sparseness of the spatial domain. This fact motivates the use of CS-based sampling and sparsity-based reconstruction techniques to jointly evaluate all possible hypotheses, thus avoiding the traditional position-by-position scanning where the multiple location hypotheses are evaluated independently. In so doing, we not only achieve a significant reduction in computational time but also we relax the sampling requirements.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Energy analysis of a contention tree-based access protocol for machine-to-machine networks with idle-to-saturation traffic transitions

  • Vázquez-Gallego, Francisco
  • Alonso-Zárate, Jesús
  • Tuset-Peiro, Pere
  • Alonso Zárate, Luis Gonzaga|||0000-0002-6608-0862
Machine-to-Machine (M2M) area networks must provide connectivity between an M2M gateway and a large number of energy-constrained M2M devices. Attaining high energy efficiency is essential in order to prolong devices lifetime. In this paper, we consider a wireless M2M area network composed of hundreds or even thousands of dormant devices that wake up periodically to transmit data upon request from a gateway. We theoretically analyze the energy efficiency of a Medium Access Control (MAC) protocol that uses a tree-splitting algorithm to resolve the collisions among devices: the Distributed Queuing (DQ) access. Computer-based simulations have been carried out to validate the accuracy of the analytical model and to evaluate and compare the energy consumption of devices using also a basic Contention Tree Algorithm (CTA) and Frame Slotted-ALOHA (FSA). Results show that DQ can reduce energy consumption in more than 35% with respect to CTA and in more than 80% with respect to FSA in dense M2M area networks with devices in compliance with the IEEE 802.15.4 physical layer., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Energy profiling of FPGA-based PHY-layer building blocks encountered in modern wireless communication systems

  • Bartzoudis, Nikolaos
  • Font Bach, Oriol
  • Payaró Llisterri, Miquel
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
  • Rubio López, Javier
  • García Fernández, Juan José
  • García Armada, Ana
Characterizing the energy cost of different physical (PHY) layer building blocks is becoming increasingly important in modern cellular-based communications, considering the cross sector requirements for performance enhancements and energy savings. This paper presents energy profiling metrics of different PHY-layer FPGA implementations encountered in modern wireless communication systems. The results give an insight of the distribution of the consumed energy in different baseband building blocks or configurations before and after applying power optimizations in the FPGA design and implementation., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Base station on/off strategies for wireless networks powered with energy harvesting sources

  • Rubio López, Javier
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
  • Vidal Manzano, José|||0000-0002-1985-2065
In this paper, we present a procedure for switching on and off base stations (BSs) that are powered with solar panels and have finite batteries. In the scenario under consideration it is considered that the BSs are placed at the same site with fully overlapped coverage areas and using different frequencies. We propose a decision strategy where we assume perfect knowledge of the traffic profile and a second approach where a robust Bayesian strategy is considered in order to account for possible error modeling in the traffic profile information., The research leading to these results has received funding from the European Commission in the framework of the FP7 Network of Excellence in Wireless COMmunications NEWCOM# (Grant agreement no. 318306) and project TUCAN3G (Grant agreement no. ICT-2011-601102), from the Spanish Ministry of Economy and Competitiveness (Ministerio de Economía y Competitividad) through the project TEC2011-29006-C03-02 (GRE3N-LINK-MAC), project TEC2013-41315-R (DISNET), and FPI grant BES-2012-052850, and from the Catalan Government (AGAUR) through the grant 2014 SGR 60., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Optimization of radio and computational resources for energy efficiency in latency-constrained application offloading

  • Muñoz Medina, Olga|||0000-0002-8739-7068
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
  • Vidal Manzano, José|||0000-0002-1985-2065
Providing femto access points (FAPs) with computational capabilities will allow (either total or partial) offloading of highly demanding applications from smartphones to the so-called femto-cloud. Such offloading promises to be beneficial in terms of battery savings at the mobile terminal (MT) and/or in latency reduction in the execution of applications. However, for this promise to become a reality, the energy and/or the time required for the communication process must be compensated by the energy and/or the time savings that result from the remote computation at the FAPs. For this problem, we provide in this paper a framework for the joint optimization of the radio and computational resource usage exploiting the tradeoff between energy consumption and latency. Multiple antennas are assumed to be available at the MT and the serving FAP. As a result of the optimization, the optimal communication strategy (e.g., transmission power, rate, and precoder) is obtained, as well as the optimal distribution of the computational load between the handset and the serving FAP. This paper also establishes the conditions under which total or no offloading is optimal, determines which is the minimum affordable latency in the execution of the application, and analyzes, as a particular case, the minimization of the total consumed energy without latency constraints., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Cramér-Rao lower bound for breakpoint distance estimation in a path-loss model

  • Castro Arvizu, Juan Manuel
  • Closas Gómez, Pau
  • Fernández Rubio, Juan Antonio|||0000-0003-1494-5366
This paper addresses the problem of determining the Cramér-Rao lower bound (CRLB) for the parameters and breakpoint distance in a Path-Loss Channel model for Received Signal Strength (RSS) measurements. The path loss model is usually assumed for corrupted RSS measurements due to the shadow fading channel feature. In this paper the two-slope path loss model is considered, in which RSS measurements are modeled differently for close and far distances. Closed-form expressions for the CRLB parameters are derived for unknown breakpoint distance. For unknown parameters and breakpoint distance value, a Bayesian estimation method is proposed. The CRLB is then compared with the performance of the herein proposed method. The comparison illustrates convergence and efficiency of the Bayesian estimator.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Asymptotic analysis of multiuser-MIMO networks with battery-constrained receivers

  • Rubio López, Javier
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
  • García Fernández, Juan José
  • García Armada, Ana
  • Font Bach, Oriol
  • Bartzoudis, Nikolaos
In this paper, we present an asymptotic analysis of the behavior of a network where the mobile terminals are considered to be battery-powered devices provided with energy harvesting capabilities. The asymptotic analysis is based on a multiuser MIMO resource allocation strategy where the battery status of the mobile terminals are considered explicitly in the proposed allocation policy. We provide some numerical results and analytic expressions of the expected value of the data rates and the battery levels for different decoding power consumption models when convergence is attained., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Standardized low-power wireless communication technologies for distributed sensing applications

  • Vilajosana, Xavier
  • Tuset-Peiro, Pere
  • Vázquez Gallego, Francisco
  • Alonso-Zárate, Jesús
  • Alonso Zárate, Luis Gonzaga|||0000-0002-6608-0862
Recent standardization efforts on low-power wireless communication technologies, including time-slotted channel hopping (TSCH) and DASH7 Alliance Mode (D7AM), are starting to change industrial sensing applications, enabling networks to scale up to thousands of nodes whilst achieving high reliability. Past technologies, such as ZigBee, rooted in IEEE 802.15.4, and ISO 18000-7, rooted in frame-slotted ALOHA (FSA), are based on contention medium access control (MAC) layers and have very poor performance in dense networks, thus preventing the Internet of Things (IoT) paradigm from really taking off. Industrial sensing applications, such as those being deployed in oil refineries, have stringent requirements on data reliability and are being built using new standards. Despite the benefits of these new technologies, industrial shifts are not happening due to the enormous technology development and adoption costs and the fact that new standards are not well-known and completely understood. In this article, we provide a deep analysis of TSCH and D7AM, outlining operational and implementation details with the aim of facilitating the adoption of these technologies to sensor application developers., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Simultaneous tracking and RSS model calibration by robust filtering

  • Castro Arvizu, Juan Manuel
  • Vila Valls, Jordi
  • Closas, Pau
  • Fernández Rubio, Juan Antonio|||0000-0003-1494-5366
Received Signal Strength (RSS) localization is widely used due to its simplicity and availability in most mobile devices. The RSS channel model is defined by the propagation losses and the shadow fading. These parameters might vary over time because of changes in the environment. In this paper, the problem of tracking a mobile node by RSS measurements is addressed, while simultaneously estimating a two-slope RSS model. The methodology considers a Kalman filter with Interacting Multiple Model architecture, coupled to an on-line estimation of the observation’s variance. The performance of the method is shown through numerical simulations in realistic scenarios., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Relay subset selection in cognitive networks with imperfect CSI and individual power constraints

  • Nájar Martón, Montserrat|||0000-0003-3507-5689
  • Blanco, Luis
This paper considers the relay subset selection problem in an underlay cognitive network in which two secondary users communicate assisted by a set of N potential relays. More specifically, this paper deals with the joint problem of choosing the best subset of L secondary relays and their corresponding weights which maximize the Signal-to-Interference-plus-Noise ratio (SINR) at the secondary user receiver, subject to per-relay power constraints and interference power constraints at the primary user. This problem is a combinatorial problem with a high computational burden. Nevertheless, we propose a sub-optimal technique, based on a convex relaxation of the problem, which achieves a near-optimal performance with a reduced complexity. Contrary to other approaches in the literature, the secondary relays are not limited to cooperate at full power., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Subset relay selection in wireless cooperative networks using sparsity-inducing norms

  • Blanco, Luis
  • Nájar Martón, Montserrat|||0000-0003-3507-5689
This paper addresses the problem of multiple relay selection in a two-hop wireless cooperative network. In particular, the proposed technique selects the best subset of relays, in a distributed beamforming scheme, which maximizes the signal-to-noise ratio at the destination node subject to individual power constraints at the relays. The selection of the best subset of K relays out of a set of N potential relay nodes, under individual power constraints, is a hard combinatorial problem with a high computational burden. The approach considered herein consists in relaxing this problem into a convex one by considering a sparsity-inducing norm. The method exposed in this paper is based on the knowledge of the second-order statistics of the channels and achieves a near-optimal performance with a computational burden which is far less than the one needed in the combinatorial search. Furthermore, in the proposed technique, contrary to other approaches in the literature, the relays are not limited to cooperate with full power.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Performance evaluation of frame slotted-ALOHA with succesive interference cancellation in machine-to-machine networks

  • Vázquez-Gallego, Francisco
  • Rietti, Marc
  • Bas, Joan
  • Alonso-Zárate, Jesús
  • Alonso Zárate, Luis Gonzaga|||0000-0002-6608-0862
Machine-to-Machine (M2M) area networks connect a gateway with a huge number of energy-constrained end-devices. Therefore, energy efficiency is essential to prolong the lifetime of M2M networks. In this paper, we consider an M2M area network composed of hundreds or thousands of end-devices that periodically transmit data upon request from a gateway. We propose a Medium Access Control (MAC) protocol based on Frame Slotted-ALOHA (FSA) with Successive Interference Cancellation (SIC), also referred to as SIC-FSA, for data collection applications. By means of comprehensive computer-based simulations, we evaluate the delay and the energy consumed by the gateway and the enddevices using SIC-FSA. We have compared the delay and energy performance provided by SIC-FSA with that of conventional FSA and diversity-FSA (D-FSA). Results show that SIC-FSA can reduce the delay and energy consumption of the gateway in more than 50%, and the energy consumed by an end-device in more than 10%, with respect to FSA in dense M2M networks equipped with radio-transceivers in compliance with the IEEE 802.11 physical layer., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Amping up, saving power

  • López Bueno, David|||0000-0002-9005-0532
  • Wang, Teng|||0000-0003-3705-9770
  • Gilabert Pinal, Pere Lluís|||0000-0001-6183-6977
  • Montoro López, Gabriel|||0000-0002-1328-4175
©2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Fourth-generation (4G) communication systems based on orthogonal frequency division multiplexing (OFDM) and the proposed backwards compatible fifth-generation (5G) variants, like filter-bank multicarrier (FBMC), are based on modulation techniques that allow significantly increased spectral efficiency and capacity in mobile radio access networks (RANs). However, the use of these modulation techniques impacts the requirements of the radio base stations, which have been traditionally the most energy-consuming element of mobile networks, accounting for up to 80% of the energy consumption of RANs [1]. Non-constant envelope-modulation techniques with high peak-to-average power ratios (PAPRs) require highly linear power amplifier (PA) amplitude and phase responses to fulfill stringent spectral mask and modulation accuracy requirements. This is often achieved with significant PA back-off, which considerably reduces PA efficiency because the PA's maximum efficiency is achieved near the saturation point., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Is the random access channel of LTE and LTE-A suitable for M2M communications? A survey of alternatives

  • Laya Romero, Andrés Ernesto
  • Alonso Zárate, Luis Gonzaga|||0000-0002-6608-0862
  • Alonso-Zárate, Jesús
The 3GPP has raised the need to revisit the design of next generations of cellular networks in order to make them capable and efficient to provide M2M services. One of the key challenges that has been identified is the need to enhance the operation of the random access channel of LTE and LTE-A. The current mechanism to request access to the system is known to suffer from congestion and overloading in the presence of a huge number of devices. For this reason, different research groups around the globe are working towards the design of more efficient ways of managing the access to these networks in such circumstances. This paper aims to provide a survey of the alternatives that have been proposed over the last years to improve the operation of the random access channel of LTE and LTE-A. A comprehensive discussion of the different alternatives is provided, identifying strengths and weaknesses of each one of them, while drawing future trends to steer the efforts over the same shooting line. In addition, while existing literature has been focused on the performance in terms of delay, the energy efficiency of the access mechanism of LTE will play a key role in the deployment of M2M networks. For this reason, a comprehensive performance evaluation of the energy efficiency of the random access mechanism of LTE is provided in this paper. The aim of this computer-based simulation study is to set a baseline performance upon which new and more energy-efficient mechanisms can be designed in the near future., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A stochastic approach for resource allocation with backhaul and energy harvesting constraints

  • Rubio López, Javier
  • Muñoz Medina, Olga|||0000-0002-8739-7068
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
We propose a novel stochastic radio-resource-allocation strategy that achieves long-term fairness considering backhaul and air-interface capacity limitations. The base station (BS) is powered only with a finite battery that is recharged by an energy harvester. The energy harvesting is also taken into account in the proposed resource-allocation strategy. The constrained scenario is often found in remote rural areas where the backhaul connection is limited, and the BSs are fed with solar panels of reduced size. Our results show that the proposed scheme achieves higher fairness among the users and provides greater worst user rate and sum rate if an average backhaul constraint is considered., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A framework for dynamic network architecture and topology optimization

  • Shafigh, Alireza Shams
  • Lorenzo, Beatriz
  • Glisic, Savo
  • Pérez Romero, Jordi|||0000-0001-9131-5013
  • DaSilva, Luiz A.
  • MacKenzie, Allen B.
  • Röning, Juha
A new paradigm in wireless network access is presented and analyzed. In this concept, certain classes of wireless terminals can be turned temporarily into an access point (AP) anytime while connected to the Internet. This creates a dynamic network architecture (DNA) since the number and location of these APs vary in time. In this paper, we present a framework to optimize different aspects of this architecture. First, the dynamic AP association problem is addressed with the aim to optimize the network by choosing the most convenient APs to provide the quality-of-service (QoS) levels demanded by the users with the minimum cost. Then, an economic model is developed to compensate the users for serving as APs and, thus, augmenting the network resources. The users' security investment is also taken into account in the AP selection. A preclustering process of the DNA is proposed to keep the optimization process feasible in a high dense network. To dynamically reconfigure the optimum topology and adjust it to the traffic variations, a new specific encoding of genetic algorithm (GA) is presented. Numerical results show that GA can provide the optimum topology up to two orders of magnitude faster than exhaustive search for network clusters, and the improvement significantly increases with the cluster size., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

User association strategies in HetNets leading to rate balancing under energy constraints

  • Rubio López, Javier
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
  • Olmo Alòs, Jaume del|||0000-0002-3361-6077
  • Vidal Manzano, José|||0000-0002-1985-2065
This paper deals with the development of several strategies for associating users to base stations (BSs) in heterogeneous networks. These strategies are able to balance the rate among users and BSs and increase the overall network utility. Constraints related to the energy availability at BSs are considered explicitly in the design, assuming that the BSs are equipped with batteries that are recharged through energy harvesting. We develop a general association strategy, and then we present several suboptimum but less complex solutions suitable for scenarios with high mobility or deployments of BSs with low computational capabilities. We also present an implementation that is to be executed in a distributed way among users and BSs without the need of having a central entity gathering all the information. The performance of the proposed strategies is evaluated through simulations in terms of rate balancing and the effect of the energy harvesting capabilities on the network throughput is shown. We also compare the proposed strategies with the traditional max-SINR user association approach., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Experimental energy consumption of Frame Slotted ALOHA and Distributed Queuing for data collection scenarios

  • Tuset-Peiro, Pere
  • Vázquez-Gallego, Francisco
  • Alonso-Zárate, Jesús
  • Alonso Zárate, Luis Gonzaga|||0000-0002-6608-0862
  • Vilajosana, Xavier
Data collection is a key scenario for the Internet of Things because it enables gathering sensor data from distributed nodes that use low-power and long-range wireless technologies to communicate in a single-hop approach. In this kind of scenario, the network is composed of one coordinator that covers a particular area and a large number of nodes, typically hundreds or thousands, that transmit data to the coordinator upon request. Considering this scenario, in this paper we experimentally validate the energy consumption of two Medium Access Control (MAC) protocols, Frame Slotted ALOHA (FSA) and Distributed Queuing (DQ). We model both protocols as a state machine and conduct experiments to measure the average energy consumption in each state and the average number of times that a node has to be in each state in order to transmit a data packet to the coordinator. The results show that FSA is more energy efficient than DQ if the number of nodes is known a priori because the number of slots per frame can be adjusted accordingly. However, in such scenarios the number of nodes cannot be easily anticipated, leading to additional packet collisions and a higher energy consumption due to retransmissions. Contrarily, DQ does not require to know the number of nodes in advance because it is able to efficiently construct an ad hoc network schedule for each collection round. This kind of a schedule ensures that there are no packet collisions during data transmission, thus leading to an energy consumption reduction above 10% compared to FSA., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Characterization of the effects of multi-tap filtering on FBMC/OQAM systems

  • Caus, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
  • Kliks, Adrian
The filter bank multicarrier modulation based on offset quadrature amplitude modulation (FBMC/OQAM) is being considered as an eligible technology for future wireless communications. However, the orthogonality may be destroyed in the presence of multipath fading, and thus, the demodulated data may be affected by inter-symbol and inter-carrier interference. To restore the orthogonality, it is deemed necessary to either precode the symbols to be transmitted or equalize the demodulated data. Under severe propagation conditions, both the precoders and equalizers should perform multi-tap filtering. In this paper, we try to determine whether it is the best choice to combat the channel at the transmit, or at the receive side. The answer to this question is not trivial, since with data precoding, the transmit power may increase, while equalization at the receive side may enhance the noise power. To cast light on this issue, this paper characterizes the average transmit and noise power to determine the influence of multi-tap filtering on the transmit signal power and on the noise variance. The analysis conducted in this paper reveals that if multi-tap precoding yields a power increase, then the noise variance would increase with the same magnitude if the same linear filter was moved from the transmit to the receive side. Therefore, if symbols are properly scaled when the transmit power increases, there is no degradation due to placing the complexity burden at the reception rather than at the transmission. To scale the symbols, it is mandatory to know the additional transmit power. In this sense, a low-complexity method to estimate the power increase is proposed. Simulation-based results confirm that the estimation is reasonably accurate., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Measuring the performance of a distributed interference management scheme in a LTE-based HetNet deployment

  • Font Bach, Oriol
  • Bartzoudis, Nikolaos
  • Payaró Llisterri, Miquel
  • Pascual Iserte, Antonio|||0000-0001-5596-2029
This paper presents the experimental evaluation of an interference- mitigation scheme tailored for heterogeneous multi-cell LTE-based systems. The real-time FPGA-based system implementation was evaluated under realistic operating conditions using the GEDOMIS® testbed. An intensive measurement campaign was conducted to assess the performance-gains of the proposed scheme, considering mobile channels and various levels of noise and interference., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Technical advances in the design and deployment of future heterogeneous networks

  • Kliks, Adrian
  • Pérez Romero, Jordi|||0000-0001-9131-5013
  • Boukhatem, Lila
  • Zalonis, Andreas
The trend in wireless communications systems is the enhancement of the network infrastructure with the introduction of small cells, where a specific geographical area is served by low-range, low-power access points. The result is the creation of a heterogeneous topology where macrocells coexist with a variety of small-cell types. In this editorial article we briefly summarize the recent technical advances in the design and deployment of future heterogeneous networks addressed in the papers that compose this special issue. In particular the following aspects are considered: the design of interference and radio resource management algorithms, the analysis of the energy efficiency and power control issues in heterogeneous networks, the concept of coordination in small cell networks, key backhaul aspects of HetNets, deployment issues and overall management strategies., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Capacity analysis of WCC-FBMC/OQAM systems

  • Cans, Marius
  • Pérez Neira, Ana Isabel|||0000-0003-4281-3934
  • Kliks, Adrian
  • Bodinier, Quentin
  • Faouzi, Bader
This paper evaluates the capacity of weighted circularly convolved FBMC/OQAM systems. A rigorous mathematical model is derived to calculate the increase of capacity that can be obtained thanks to the lattice structure of the modulation and the exploitation of the intrinsic interference. The numerical results reveal that a signal to noise ratio gain of 2dB is obtained in one resource block of 12 subcarriers, translating into a capacity increase of 11% with respect to OFDM, which nuances some previous results on this topic in the literature., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Base station on/off strategies for wireless networks powered with energy harvesting sources

  • Rubio López, Javier
  • Pascual Iserte, Antonio
  • Vidal Manzano, José
In this paper, we present a procedure for switching on and off base stations (BSs) that are powered with solar panels and have finite batteries. In the scenario under consideration it is considered that the BSs are placed at the same site with fully overlapped coverage areas and using different frequencies. We propose a decision strategy where we assume perfect knowledge of the traffic profile and a second approach where a robust Bayesian strategy is considered in order to account for possible error modeling in the traffic profile information., The research leading to these results has received funding from the European Commission in the framework of the FP7 Network of Excellence in Wireless COMmunications NEWCOM# (Grant agreement no. 318306) and project TUCAN3G (Grant agreement no. ICT-2011-601102), from the Spanish Ministry of Economy and Competitiveness (Ministerio de Economía y Competitividad) through the project TEC2011-29006-C03-02 (GRE3N-LINK-MAC), project TEC2013-41315-R (DISNET), and FPI grant BES-2012-052850, and from the Catalan Government (AGAUR) through the grant 2014 SGR 60., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A framework for dynamic network architecture and topology optimization

  • Shafigh, Alireza Shams
  • Lorenzo, Beatriz
  • Glisic, Savo
  • Pérez Romero, Jordi
  • DaSilva, Luiz A.
  • MacKenzie, Allen B.
  • Röning, Juha
A new paradigm in wireless network access is presented and analyzed. In this concept, certain classes of wireless terminals can be turned temporarily into an access point (AP) anytime while connected to the Internet. This creates a dynamic network architecture (DNA) since the number and location of these APs vary in time. In this paper, we present a framework to optimize different aspects of this architecture. First, the dynamic AP association problem is addressed with the aim to optimize the network by choosing the most convenient APs to provide the quality-of-service (QoS) levels demanded by the users with the minimum cost. Then, an economic model is developed to compensate the users for serving as APs and, thus, augmenting the network resources. The users' security investment is also taken into account in the AP selection. A preclustering process of the DNA is proposed to keep the optimization process feasible in a high dense network. To dynamically reconfigure the optimum topology and adjust it to the traffic variations, a new specific encoding of genetic algorithm (GA) is presented. Numerical results show that GA can provide the optimum topology up to two orders of magnitude faster than exhaustive search for network clusters, and the improvement significantly increases with the cluster size., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A margin adaptive scheduling algorithm for FBMC/OQAM systems

  • Caus López, Marius
  • Pérez Neira, Ana Isabel
  • Moretti, Marco
  • Kliks, Adrian
This paper addresses the margin adaptive problem for the filter bank multicarrier (FBMC) modulation based on the offset QAM (OQAM), referred to as FBMC/OQAM. The analysis conducted in this paper reveals that due to the specific FBMC/OQAM transmission format the system has to deal with inter-user, inter-symbol and inter-carrier interference to solve the resource allocation problem. To manage the interference, the successive channel allocation method, originally proposed for the orthogonal frequency division multiplexing (OFDM), has been modified by organizing subcarriers in groups and assigning subcarriers to users in a block-wise fashion. Following this strategy and making some approximations we demonstrate that it is possible to pose a single problem that is valid for OFDM and FBMC/OQAM. In this case, numerical results show that FBMC/OQAM is more energy-efficient than OFDM because it requires less power to transmit the same information rate., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Cramér-Rao lower bound for breakpoint distance estimation in a path-loss model

  • Castro Arvizu, Juan Manuel
  • Closas Gómez, Pau
  • Fernández Rubio, Juan Antonio
This paper addresses the problem of determining the Cramér-Rao lower bound (CRLB) for the parameters and breakpoint distance in a Path-Loss Channel model for Received Signal Strength (RSS) measurements. The path loss model is usually assumed for corrupted RSS measurements due to the shadow fading channel feature. In this paper the two-slope path loss model is considered, in which RSS measurements are modeled differently for close and far distances. Closed-form expressions for the CRLB parameters are derived for unknown breakpoint distance. For unknown parameters and breakpoint distance value, a Bayesian estimation method is proposed. The CRLB is then compared with the performance of the herein proposed method. The comparison illustrates convergence and efficiency of the Bayesian estimator., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Simultaneous tracking and RSS model calibration by robust filtering

  • Castro Arvizu, Juan Manuel
  • Vila Valls, Jordi
  • Closas, Pau
  • Fernández Rubio, Juan Antonio
Received Signal Strength (RSS) localization is widely used due to its simplicity and availability in most mobile devices. The RSS channel model is defined by the propagation losses and the shadow fading. These parameters might vary over time because of changes in the environment. In this paper, the problem of tracking a mobile node by RSS measurements is addressed, while simultaneously estimating a two-slope RSS model. The methodology considers a Kalman filter with Interacting Multiple Model architecture, coupled to an on-line estimation of the observation’s variance. The performance of the method is shown through numerical simulations in realistic scenarios., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Spatial sparsity based direct positioning for IR-UWB in IEEE 802.15.4a channels

  • Lagunas Targarona, Eva
  • Navarro, Mònica
  • Closas Gómez, Pau
  • Nájar Martón, Montserrat
In this paper, we focus on the application of Compressive Sensing (CS) techniques to Impulse Radio (IR) Ultra-WideBand (UWB) positioning systems under indoor propagation environments. Direct Position Estimation (DPE) approaches can potentially improve the position estimation accuracy of conventional two-step techniques by directly estimating the position coordinates from the observed signal in a single step. Furthermore, DPE does not require a threshold selection upon which accuracy of two-step approaches depend on. Although in the presence of multipath the actual gains are not straight forward, recent evaluation of DPE positioning in IR-UWB system proved accurate positioning estimate gains. However it comes at a cost of higher computational complexity. This paper exploits the sparseness of the problem to reduce the computational load of the positioning estimation process and relax the requirements of the Analog to Digital Converter (ADC) when sampling UWB signals. Based on the fact that the number of unknown targets is small in the discrete spatial domain, this paper incorporates the multiple location hypotheses into an overcomplete basis, which highlights the sparseness of the spatial domain. This fact motivates the use of CS-based sampling and sparsity-based reconstruction techniques to jointly evaluate all possible hypotheses, thus avoiding the traditional position-by-position scanning where the multiple location hypotheses are evaluated independently. In so doing, we not only achieve a significant reduction in computational time but also we relax the sampling requirements., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Joint optimization of power and data transfer in multiuser MIMO systems

  • Rubio López, Javier
  • Pascual Iserte, Antonio
  • Palomar, Daniel P.
  • Goldsmith, Andrea
We present an approach to solve the nonconvex optimization problem that arises when designing the transmit covariance matrices in multiuser multiple-input multiple-output (MIMO) broadcast networks implementing simultaneous wireless information and power transfer (SWIPT). The MIMO SWIPT problem is formulated as a general multiobjective optimization problem, in which data rates and harvested powers are optimized simultaneously. Two different approaches are applied to reformulate the (nonconvex) multiobjective problem. In the first approach, the transmitter can control the specific amount of power to be harvested by power transfer whereas in the second approach the transmitter can only control the proportion of power to be harvested among the different harvesting users. We solve the resulting formulations using the majorization-minimization (MM) approach. The solution obtained from the MM approach is compared to the classical block-diagonalization (BD) strategy, typically used to solve the nonconvex multiuser MIMO network by forcing no interference among users. Simulation results show that the proposed approach improves over the BD approach both the system sum rate and the power harvested by users. Additionally, the computational times needed for convergence of the proposed methods are much lower than the ones required for classical gradient-based approaches., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Capacity analysis of WCC-FBMC/OQAM systems

  • Cans, Marius
  • Pérez Neira, Ana Isabel
  • Kliks, Adrian
  • Bodinier, Quentin
  • Faouzi, Bader
This paper evaluates the capacity of weighted circularly convolved FBMC/OQAM systems. A rigorous mathematical model is derived to calculate the increase of capacity that can be obtained thanks to the lattice structure of the modulation and the exploitation of the intrinsic interference. The numerical results reveal that a signal to noise ratio gain of 2dB is obtained in one resource block of 12 subcarriers, translating into a capacity increase of 11% with respect to OFDM, which nuances some previous results on this topic in the literature., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Subset relay selection in wireless cooperative networks using sparsity-inducing norms

  • Blanco, Luis
  • Nájar Martón, Montserrat
This paper addresses the problem of multiple relay selection in a two-hop wireless cooperative network. In particular, the proposed technique selects the best subset of relays, in a distributed beamforming scheme, which maximizes the signal-to-noise ratio at the destination node subject to individual power constraints at the relays. The selection of the best subset of K relays out of a set of N potential relay nodes, under individual power constraints, is a hard combinatorial problem with a high computational burden. The approach considered herein consists in relaxing this problem into a convex one by considering a sparsity-inducing norm. The method exposed in this paper is based on the knowledge of the second-order statistics of the channels and achieves a near-optimal performance with a computational burden which is far less than the one needed in the combinatorial search. Furthermore, in the proposed technique, contrary to other approaches in the literature, the relays are not limited to cooperate with full power., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Performance evaluation of frame slotted-ALOHA with succesive interference cancellation in machine-to-machine networks

  • Vázquez-Gallego, Francisco
  • Rietti, Marc
  • Bas, Joan
  • Alonso-Zárate, Jesús
  • Alonso Zárate, Luis Gonzaga
Machine-to-Machine (M2M) area networks connect a gateway with a huge number of energy-constrained end-devices. Therefore, energy efficiency is essential to prolong the lifetime of M2M networks. In this paper, we consider an M2M area network composed of hundreds or thousands of end-devices that periodically transmit data upon request from a gateway. We propose a Medium Access Control (MAC) protocol based on Frame Slotted-ALOHA (FSA) with Successive Interference Cancellation (SIC), also referred to as SIC-FSA, for data collection applications. By means of comprehensive computer-based simulations, we evaluate the delay and the energy consumed by the gateway and the enddevices using SIC-FSA. We have compared the delay and energy performance provided by SIC-FSA with that of conventional FSA and diversity-FSA (D-FSA). Results show that SIC-FSA can reduce the delay and energy consumption of the gateway in more than 50%, and the energy consumed by an end-device in more than 10%, with respect to FSA in dense M2M networks equipped with radio-transceivers in compliance with the IEEE 802.11 physical layer., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Optimization of radio and computational resources for energy efficiency in latency-constrained application offloading

  • Muñoz Medina, Olga
  • Pascual Iserte, Antonio
  • Vidal Manzano, José
Providing femto access points (FAPs) with computational capabilities will allow (either total or partial) offloading of highly demanding applications from smartphones to the so-called femto-cloud. Such offloading promises to be beneficial in terms of battery savings at the mobile terminal (MT) and/or in latency reduction in the execution of applications. However, for this promise to become a reality, the energy and/or the time required for the communication process must be compensated by the energy and/or the time savings that result from the remote computation at the FAPs. For this problem, we provide in this paper a framework for the joint optimization of the radio and computational resource usage exploiting the tradeoff between energy consumption and latency. Multiple antennas are assumed to be available at the MT and the serving FAP. As a result of the optimization, the optimal communication strategy (e.g., transmission power, rate, and precoder) is obtained, as well as the optimal distribution of the computational load between the handset and the serving FAP. This paper also establishes the conditions under which total or no offloading is optimal, determines which is the minimum affordable latency in the execution of the application, and analyzes, as a particular case, the minimization of the total consumed energy without latency constraints., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Asymptotic analysis of multiuser-MIMO networks with battery-constrained receivers

  • Rubio López, Javier
  • Pascual Iserte, Antonio
  • García Fernández, Juan José
  • García Armada, Ana
  • Font Bach, Oriol
  • Bartzoudis, Nikolaos
In this paper, we present an asymptotic analysis of the behavior of a network where the mobile terminals are considered to be battery-powered devices provided with energy harvesting capabilities. The asymptotic analysis is based on a multiuser MIMO resource allocation strategy where the battery status of the mobile terminals are considered explicitly in the proposed allocation policy. We provide some numerical results and analytic expressions of the expected value of the data rates and the battery levels for different decoding power consumption models when convergence is attained., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental energy consumption of Frame Slotted ALOHA and Distributed Queuing for data collection scenarios

  • Tuset-Peiro, Pere
  • Vázquez-Gallego, Francisco
  • Alonso-Zárate, Jesús
  • Alonso Zárate, Luis Gonzaga
  • Vilajosana, Xavier
Data collection is a key scenario for the Internet of Things because it enables gathering sensor data from distributed nodes that use low-power and long-range wireless technologies to communicate in a single-hop approach. In this kind of scenario, the network is composed of one coordinator that covers a particular area and a large number of nodes, typically hundreds or thousands, that transmit data to the coordinator upon request. Considering this scenario, in this paper we experimentally validate the energy consumption of two Medium Access Control (MAC) protocols, Frame Slotted ALOHA (FSA) and Distributed Queuing (DQ). We model both protocols as a state machine and conduct experiments to measure the average energy consumption in each state and the average number of times that a node has to be in each state in order to transmit a data packet to the coordinator. The results show that FSA is more energy efficient than DQ if the number of nodes is known a priori because the number of slots per frame can be adjusted accordingly. However, in such scenarios the number of nodes cannot be easily anticipated, leading to additional packet collisions and a higher energy consumption due to retransmissions. Contrarily, DQ does not require to know the number of nodes in advance because it is able to efficiently construct an ad hoc network schedule for each collection round. This kind of a schedule ensures that there are no packet collisions during data transmission, thus leading to an energy consumption reduction above 10% compared to FSA., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Relay subset selection in cognitive networks with imperfect CSI and individual power constraints

  • Nájar Martón, Montserrat
  • Blanco, Luis
This paper considers the relay subset selection problem in an underlay cognitive network in which two secondary users communicate assisted by a set of N potential relays. More specifically, this paper deals with the joint problem of choosing the best subset of L secondary relays and their corresponding weights which maximize the Signal-to-Interference-plus-Noise ratio (SINR) at the secondary user receiver, subject to per-relay power constraints and interference power constraints at the primary user. This problem is a combinatorial problem with a high computational burden. Nevertheless, we propose a sub-optimal technique, based on a convex relaxation of the problem, which achieves a near-optimal performance with a reduced complexity. Contrary to other approaches in the literature, the secondary relays are not limited to cooperate at full power., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Sparse multiple relay selection for network beamforming with individual power constraints using semidefinite relaxation

  • Blanco, Luis
  • Nájar Martón, Montserrat
This paper deals with the multiple relay selection problem in two-hop wireless cooperative networks with individual power constraints at the relays. In particular, it addresses the problem of selecting the best subset of K cooperative nodes and their corresponding beamforming weights so that the signal-to-noise ratio (SNR) is maximized at the destination. This problem is computationally demanding and requires an exhaustive search over all the possible combinations. In order to reduce the complexity, a new suboptimal method is proposed. This technique exhibits a near-optimal performance with a computational burden that is far less than the one needed in the combinatorial search. The proposed method is based on the use of the l1-norm squared and the Charnes-Cooper transformation and naturally leads to a semidefinite programming relaxation with an affordable computational cost. Contrary to other approaches in the literature, the technique exposed herein is based on the knowledge of the second-order statistics of the channels and the relays are not limited to cooperate with full power., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Energy consumption optimisation for duty-cycled schemes in shadowed environments

  • Predojev, Tatjana
  • Alonso-Zárate, Jesús
  • Dohler, Mischa
  • Alonso Zárate, Luis Gonzaga
The focus of this study is the optimal configuration of a wireless low-power duty-cycled network with respect to the minimal energy consumption. Precisely, the energy consumption of a truncated-ARQ scheme in realistic shadowing environments is examined for the reference IEEE 802.15.4e standard protocol and for its cooperative extension that is presented in the paper. We show how to choose between the direct or multihop forwarding and the cooperative version of the two. We determine the optimal forwarding strategy for both loose and strict reliability requirements. Low-power links are parametrised by the interdevice distance and the corresponding outage probability, for the fixed output transmission power. It is shown that significant amounts of energy can be saved when the most adequate scheme of the three is applied. All analytical results are validated in the network simulator ns-3., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Technical advances in the design and deployment of future heterogeneous networks

  • Kliks, Adrian
  • Pérez Romero, Jordi
  • Boukhatem, Lila
  • Zalonis, Andreas
The trend in wireless communications systems is the enhancement of the network infrastructure with the introduction of small cells, where a specific geographical area is served by low-range, low-power access points. The result is the creation of a heterogeneous topology where macrocells coexist with a variety of small-cell types. In this editorial article we briefly summarize the recent technical advances in the design and deployment of future heterogeneous networks addressed in the papers that compose this special issue. In particular the following aspects are considered: the design of interference and radio resource management algorithms, the analysis of the energy efficiency and power control issues in heterogeneous networks, the concept of coordination in small cell networks, key backhaul aspects of HetNets, deployment issues and overall management strategies., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Amping up, saving power

  • López Bueno, David
  • Wang, Teng
  • Gilabert Pinal, Pere Lluís
  • Montoro López, Gabriel
©2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Fourth-generation (4G) communication systems based on orthogonal frequency division multiplexing (OFDM) and the proposed backwards compatible fifth-generation (5G) variants, like filter-bank multicarrier (FBMC), are based on modulation techniques that allow significantly increased spectral efficiency and capacity in mobile radio access networks (RANs). However, the use of these modulation techniques impacts the requirements of the radio base stations, which have been traditionally the most energy-consuming element of mobile networks, accounting for up to 80% of the energy consumption of RANs [1]. Non-constant envelope-modulation techniques with high peak-to-average power ratios (PAPRs) require highly linear power amplifier (PA) amplitude and phase responses to fulfill stringent spectral mask and modulation accuracy requirements. This is often achieved with significant PA back-off, which considerably reduces PA efficiency because the PA's maximum efficiency is achieved near the saturation point., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Is the random access channel of LTE and LTE-A suitable for M2M communications? A survey of alternatives

  • Laya Romero, Andrés Ernesto
  • Alonso Zárate, Luis Gonzaga
  • Alonso-Zárate, Jesús
The 3GPP has raised the need to revisit the design of next generations of cellular networks in order to make them capable and efficient to provide M2M services. One of the key challenges that has been identified is the need to enhance the operation of the random access channel of LTE and LTE-A. The current mechanism to request access to the system is known to suffer from congestion and overloading in the presence of a huge number of devices. For this reason, different research groups around the globe are working towards the design of more efficient ways of managing the access to these networks in such circumstances. This paper aims to provide a survey of the alternatives that have been proposed over the last years to improve the operation of the random access channel of LTE and LTE-A. A comprehensive discussion of the different alternatives is provided, identifying strengths and weaknesses of each one of them, while drawing future trends to steer the efforts over the same shooting line. In addition, while existing literature has been focused on the performance in terms of delay, the energy efficiency of the access mechanism of LTE will play a key role in the deployment of M2M networks. For this reason, a comprehensive performance evaluation of the energy efficiency of the random access mechanism of LTE is provided in this paper. The aim of this computer-based simulation study is to set a baseline performance upon which new and more energy-efficient mechanisms can be designed in the near future., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A stochastic approach for resource allocation with backhaul and energy harvesting constraints

  • Rubio López, Javier
  • Muñoz Medina, Olga
  • Pascual Iserte, Antonio
We propose a novel stochastic radio-resource-allocation strategy that achieves long-term fairness considering backhaul and air-interface capacity limitations. The base station (BS) is powered only with a finite battery that is recharged by an energy harvester. The energy harvesting is also taken into account in the proposed resource-allocation strategy. The constrained scenario is often found in remote rural areas where the backhaul connection is limited, and the BSs are fed with solar panels of reduced size. Our results show that the proposed scheme achieves higher fairness among the users and provides greater worst user rate and sum rate if an average backhaul constraint is considered., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Energy analysis of a contention tree-based access protocol for machine-to-machine networks with idle-to-saturation traffic transitions

  • Vázquez-Gallego, Francisco
  • Alonso-Zárate, Jesús
  • Tuset-Peiro, Pere
  • Alonso Zárate, Luis Gonzaga
Machine-to-Machine (M2M) area networks must provide connectivity between an M2M gateway and a large number of energy-constrained M2M devices. Attaining high energy efficiency is essential in order to prolong devices lifetime. In this paper, we consider a wireless M2M area network composed of hundreds or even thousands of dormant devices that wake up periodically to transmit data upon request from a gateway. We theoretically analyze the energy efficiency of a Medium Access Control (MAC) protocol that uses a tree-splitting algorithm to resolve the collisions among devices: the Distributed Queuing (DQ) access. Computer-based simulations have been carried out to validate the accuracy of the analytical model and to evaluate and compare the energy consumption of devices using also a basic Contention Tree Algorithm (CTA) and Frame Slotted-ALOHA (FSA). Results show that DQ can reduce energy consumption in more than 35% with respect to CTA and in more than 80% with respect to FSA in dense M2M area networks with devices in compliance with the IEEE 802.15.4 physical layer., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Measuring the performance of a distributed interference management scheme in a LTE-based HetNet deployment

  • Font Bach, Oriol
  • Bartzoudis, Nikolaos
  • Payaró Llisterri, Miquel
  • Pascual Iserte, Antonio
This paper presents the experimental evaluation of an interference- mitigation scheme tailored for heterogeneous multi-cell LTE-based systems. The real-time FPGA-based system implementation was evaluated under realistic operating conditions using the GEDOMIS® testbed. An intensive measurement campaign was conducted to assess the performance-gains of the proposed scheme, considering mobile channels and various levels of noise and interference., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Assessment of RSS model calibration with real WLAN devices

  • Castro, Juan Manuel
  • Moragrega, Ana
  • Closas, Pau
  • Fernández Rubio, Juan Antonio
Received Signal Strength (RSS) for indoor localization is widely used due to its simplicity and availability in most mobile devices. The RSS channel model is defined by the propagation losses and the shadow fading. This paper studies two-slope RSS channel model and compares its validity to classical one-slope path loss model. Particularly, the work presents real-data results of a Bayesian calibration method. Validation of the model fitting is then performed in a dynamic scenario where the distance to a reference node is tracked by a Kalman Filter. Results show the superiority of two-slope model, specially at large distances., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Energy profiling of FPGA-based PHY-layer building blocks encountered in modern wireless communication systems

  • Bartzoudis, Nikolaos
  • Font Bach, Oriol
  • Payaró Llisterri, Miquel
  • Pascual Iserte, Antonio
  • Rubio López, Javier
  • García Fernández, Juan José
  • García Armada, Ana
Characterizing the energy cost of different physical (PHY) layer building blocks is becoming increasingly important in modern cellular-based communications, considering the cross sector requirements for performance enhancements and energy savings. This paper presents energy profiling metrics of different PHY-layer FPGA implementations encountered in modern wireless communication systems. The results give an insight of the distribution of the consumed energy in different baseband building blocks or configurations before and after applying power optimizations in the FPGA design and implementation., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Device-to-device communications and small cells: enabling spectrum reuse for dense networks

  • Laya, Andrés
  • Wang, Kun
  • Ahmed, Ashraf Awadelkarim Widaa
  • Alonso Zárate, Jesús
  • Markendhal, Jan
  • Alonso Zárate, Luis Gonzaga
In the evolution of communication networks, there has always been a need to increase the capacity to cope with the continuous growing demand for data transmission. However, with the arrival of the Internet-of-Things and the commoditization of broadband access through smartphones, tablets, smart-watches, and all types of connecting devices, future networks must be capable of providing higher bandwidth and Quality of Experience, as wellas operating in dense networks with a massive number of simultaneous connections. This high number of connections will be very heterogeneous, spanning from highly-demanding data rate applications to low-complexity and high energy-efficient Machine-to-Machine communications. In such a dense and complex scenario, a more flexible use of spectrum resources is deemed to be the way to meet the growing requirements for data transmission. In particular, this article focuses on Device-to-Device communications and small cell deployments as emerging facilitators of such a demanding and heterogeneous scenario. The pros and cons of both complementary strategies are identified from both a technical and a business point of view, and main standardization activities are discussed. The aim of this article is to identify and describe open challenges and to inspire new areas for research that make viable the next generation of dense networks., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Standardized low-power wireless communication technologies for distributed sensing applications

  • Vilajosana, Xavier
  • Tuset-Peiro, Pere
  • Vázquez Gallego, Francisco
  • Alonso-Zárate, Jesús
  • Alonso Zárate, Luis Gonzaga
Recent standardization efforts on low-power wireless communication technologies, including time-slotted channel hopping (TSCH) and DASH7 Alliance Mode (D7AM), are starting to change industrial sensing applications, enabling networks to scale up to thousands of nodes whilst achieving high reliability. Past technologies, such as ZigBee, rooted in IEEE 802.15.4, and ISO 18000-7, rooted in frame-slotted ALOHA (FSA), are based on contention medium access control (MAC) layers and have very poor performance in dense networks, thus preventing the Internet of Things (IoT) paradigm from really taking off. Industrial sensing applications, such as those being deployed in oil refineries, have stringent requirements on data reliability and are being built using new standards. Despite the benefits of these new technologies, industrial shifts are not happening due to the enormous technology development and adoption costs and the fact that new standards are not well-known and completely understood. In this article, we provide a deep analysis of TSCH and D7AM, outlining operational and implementation details with the aim of facilitating the adoption of these technologies to sensor application developers., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

User association strategies in HetNets leading to rate balancing under energy constraints

  • Rubio López, Javier
  • Pascual Iserte, Antonio
  • Olmo Alòs, Jaume del
  • Vidal Manzano, José
This paper deals with the development of several strategies for associating users to base stations (BSs) in heterogeneous networks. These strategies are able to balance the rate among users and BSs and increase the overall network utility. Constraints related to the energy availability at BSs are considered explicitly in the design, assuming that the BSs are equipped with batteries that are recharged through energy harvesting. We develop a general association strategy, and then we present several suboptimum but less complex solutions suitable for scenarios with high mobility or deployments of BSs with low computational capabilities. We also present an implementation that is to be executed in a distributed way among users and BSs without the need of having a central entity gathering all the information. The performance of the proposed strategies is evaluated through simulations in terms of rate balancing and the effect of the energy harvesting capabilities on the network throughput is shown. We also compare the proposed strategies with the traditional max-SINR user association approach., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Characterization of the effects of multi-tap filtering on FBMC/OQAM systems

  • Caus, Marius
  • Pérez Neira, Ana Isabel
  • Kliks, Adrian
The filter bank multicarrier modulation based on offset quadrature amplitude modulation (FBMC/OQAM) is being considered as an eligible technology for future wireless communications. However, the orthogonality may be destroyed in the presence of multipath fading, and thus, the demodulated data may be affected by inter-symbol and inter-carrier interference. To restore the orthogonality, it is deemed necessary to either precode the symbols to be transmitted or equalize the demodulated data. Under severe propagation conditions, both the precoders and equalizers should perform multi-tap filtering. In this paper, we try to determine whether it is the best choice to combat the channel at the transmit, or at the receive side. The answer to this question is not trivial, since with data precoding, the transmit power may increase, while equalization at the receive side may enhance the noise power. To cast light on this issue, this paper characterizes the average transmit and noise power to determine the influence of multi-tap filtering on the transmit signal power and on the noise variance. The analysis conducted in this paper reveals that if multi-tap precoding yields a power increase, then the noise variance would increase with the same magnitude if the same linear filter was moved from the transmit to the receive side. Therefore, if symbols are properly scaled when the transmit power increases, there is no degradation due to placing the complexity burden at the reception rather than at the transmission. To scale the symbols, it is mandatory to know the additional transmit power. In this sense, a low-complexity method to estimate the power increase is proposed. Simulation-based results confirm that the estimation is reasonably accurate., Peer Reviewed, Postprint (published version)