Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Application of Commercial Surface Pretreatments on the Formation of Cerium Conversion Coating (CeCC) over High-Strength Aluminum Alloys 2024-T3 and 7075-T6

  • Alba Galvín, Juan Jesús
  • González Rovira, Leandro
  • Botana Pedemonte, Francisco Javier
  • Lekka, Maria
  • Andreatta, Francesco
  • Fedrizzi, Lorenzo
  • Bethencourt Núñez, Manuel
The selection of appropriate surface pretreatments is one of the pending issues for the industrial application of cerium-based chemical conversion coatings (CeCC) as an alternative for toxic chromate conversion coating (CrCC). A two-step surface pretreatment based on commercial products has been successfully used here to obtain CeCC on AA2024-T3 and AA7075-T6. Specimens processed for 1 to 15 min in solutions containing CeCl3 and H2O2 have been studied by scanning electron microscopy coupled with energy-dispersive X-ray analysis (SEM-EDX), glow discharge optical emission spectroscopy (GDOES), potentiodynamic linear polarization (LP), electrochemical impedance spectroscopy (EIS), and neutral salt spray (NSS) tests. SEM-EDX showed that CeCC was firstly observed as deposits, followed by a general coverage of the surface with the formation of cracks where the coating was getting thicker. GDOES confirmed an increase of the CeCC thickness as the deposition proceed, the formation of CeCC over 7075 being faster than over 2024. There was a Ce-rich layer in both alloys and an aluminum oxide/hydroxide layer on 7075 between the upper Ce-rich layer and the aluminum matrix. According to LP and EIS, CeCC in all samples offered cathodic protection and comparable degradation in chloride-containing media. Finally, the NSS test corroborated the anti-corrosion properties of the CeCC obtained after the commercial pretreatments employed., This research was funded by the Ministry of Economy, Industry and Competitiveness of Spain/FEDER Program of the EU. Project: Optimizacion y viabilidad industrial del proceso de preparacion de capas de conversion basadas en cerio sobre aleaciones de aluminio. Reference MAT2014-60857-R. The APC was funded by Instituto Universitario de Investigacion Marina (INMAR) of the University of Cadiz and the Programa de Fomento e Impulso de la Actividad de Investigacion y Transferencia of the University of Cadiz.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On the attrition evaluation of oxygen carriers in Chemical Looping Combustion

  • Cabello Flores, Arturo
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
© 2016. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical Looping Combustion (CLC) is one of the most promising processes for the low-cost capture of CO2. It is based on the transfer of oxygen from air to the fuel by means of a solid oxygen carrier that circulates between two interconnected fluidized bed reactors: the fuel reactor and the air reactor. CO2 capture is inherent to this process since air does not become mixed with the fuel. A key issue for the large-scale development of CLC technology is the selection of oxygen carrier materials with suitable properties such as high reactivity and good fluidization. Another important feature that an oxygen carrier must fulfil is to have high resistance to attrition. For this purpose, several particle characteristics related to attrition resistance were analysed in this work on 23 oxygen carriers, both natural and synthetic, prepared by different methods and using different metal oxides. Particle crushing strength and Air Jet Index (AJI) were determined for the fresh materials, as well as the attrition rate and the corresponding particle lifetime during multi-cycle redox reactions in a continuously operated CLC unit for gaseous fuels. A comparison was made of the different methods used to evaluate attrition behaviour. The AJI-ASTM test for particles subjected to long-term CLC operation was used as a standard screening tool to evaluate the attrition behaviour of the oxygen carriers. Finally, a methodology was proposed for the selection of oxygen carriers as eligible materials for CLC scale-up based on attrition behaviour., The work presented in this article was partially funded by the Spanish Ministry of Economy and Competitiveness (ENE2013-45454-R), by the European Commission Seventh Framework Programme under grant agreement No. 608571 (Project acronym SUCCESS) and by the European Regional Development Fund (ERDF). A. Abad and A. Cabello thank CSIC for the financial support given to project 201480E101. ICB-CSIC also thanks Johnson Matthey for the preparation of some of the oxygen carriers tested in this work., Peer reviewed