Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Steady-state analysis of the modular multilevel converter.

  • Westerman Spier, Daniel|||0000-0003-3477-6328
  • López Mestre, Joaquim
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
In this paper, the steady-state behavior of the modular multilevel converter (MMC) is studied under balanced and unbalanced AC grid voltage conditions. The suggested mathematical model is derived combining the converter internal arm variables and both AC and DC grids variables. Moreover, the steady-state solution of the system can be achieved by setting the internal power balance within the converter. In order to verify the steady-state model, different types of AC fault conditions are imposed, and the output values are compared with the simulation results of an average model of the MMC circuit. The results show that the proposed analysis is in close agreement with the simulations for all conditions evaluated, validating the developed equations., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Optimal current reference calculation for MMCs considering converter limitations

  • Westerman Spier, Daniel|||0000-0003-3477-6328
  • Prieto-Araujo, E.
  • López Mestre, Joaquim
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
The paper addresses an optimization-based reference calculation method for Modular Multilevel Converters (MMC) operating in normal and constrained situations (when the converter needs to prioritize its quantities as it has reached voltage or current limitations, e.g. during system faults). The optimization problem prioritizes to satisfy the external AC active and reactive current set-points demanded by the grid operator through the corresponding grid code. If the operator demands are fulfilled, it uses the available MMC degrees of freedom to minimize the arm inductance losses. Otherwise, if the operator demanded AC set-points cannot be accomplished, the optimization attempts to minimize the error prioritizing between either AC active or reactive currents. The optimization problem constraints are imposed through a steady-state model considering simultaneously the external and internal AC and DC magnitudes of the converter. The steady-state model also includes the voltage variation in the equivalent arm capacitors (considering the ripple). Then, the imposed limitations are the maximum allowed grid and arm currents, the maximum allowed arm voltages and the sub-module capacitor maximum voltages. The paper presents a detailed formulation of the optimization problem and applies it to several case studies where it is shown that the presented approach can be potentially used to obtain the MMC references both in normal and fault conditions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Methodology for interaction identification in modular multi-level converter-based HVDC systems

  • Dadjo Tavakoli, Saman
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • Sánchez Sánchez, Enric|||0000-0003-4075-0191
  • Gomis-Bellmunt, Oriol
This paper suggests a methodology for the identification, classification, and evaluation of various types of interactions that may occur in an HVDC link based on modular multi-level converters (MMC). The methodology incorporates the most suitable analytic tools for the frequency-domain study of each interaction category. To do so, a detailed nonlinear model of an MMC-based HVDC link that consists of master and slave MMCs, AC grids, and the DC transmission system is derived. Then, it is linearized to obtain a multi-input multi-output (MIMO) linear model that represents the dynamics of the complete MMC-based HVDC link. Based on the control loops of interest, interactions are classified as (1) state variable interactions, (2) disturbance interactions, (3) control loop interactions, and (4) overall system interactions. Then, through the application examples, the mentioned four categories of interactions are studied in frequency domain via the relevant analytic tools. The results obtained from the frequency-domain analysis are validated by time-domain simulation., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On resonance instabilities in VSCs connected to weak grids

  • Orellana Montaño, Luis Carlos|||0000-0002-0615-3855
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • Sainz Sapera, Luis|||0000-0002-5670-0669
  • Cheah Mañé, Marc|||0000-0002-0942-661X
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
This paper addresses the oscillatory stability phenomena studied in the literature and reported by network operators in grid-connected VSC systems. Negative interactions have been observed at different frequencies in these systems, causing the tripping of power converters (e.g. wind turbines or HVDC applications). The interaction between the controller of power converters and poorly damped AC networks are identified causes of these events. This paper analyses two methods to model grid-connected VSC systems applied in the literature to study stability: the state-space and the impedance-based model. Validation has been carried out between the two methodologies by analyzing eigenvalues and singular values of the system. Furthermore, a time-domain simulation has been done to validate the state-space model with a non-linear MATLAB/Simulink model. The stability is studied in a base case system with a grid-connected VSC to the main AC grid via an LC circuit. A sensibility analysis of the strength of the grid and an analysis of subsynchronous and harmonic oscillatory resonances has been carried out for weak grids.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Stability assessment for multi-infeed grid-connected VSCs modeled in the admittance matrix form

  • Orellana Montaño, Luis Carlos|||0000-0002-0615-3855
  • Sainz Sapera, Luis|||0000-0002-5670-0669
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The increasing use of power electronics converters to integrate renewable energy sources has been a subject of concern due to the resonance oscillatory phenomena caused by their interaction with poorly damped AC networks. Early studies are focused on assessing the controller influence of a single converter connected to simple networks, and they are no longer representative for existing systems. Lately, studies of multi-infeed grid-connected converters are of particular interest, and their main aim is to apply traditional criteria and identify their difficulties in the stability assessment. An extension of traditional criteria is commonly proposed as a result of these analysis, but they can be burdensome for large and complex power systems. The present work addresses this issue by proposing a simple criterion to assess the stability of large power systems with high-penetration of power converters. The criterion has its origin in the mode analysis and positive-net damping stability criteria, and it addresses the stability in the frequency domain by studying the eigenvalues magnitude and real component of dynamic models in the admittance matrix form. Its effectiveness is tested in two case studies developed in Matlab/Simulink which compare it with traditional criteria, proving its simplicity., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Optimal H-infinity control design for MMC-based HVDC links

  • Dadjo Tavakoli, Saman
  • Fekriasl, Sajjad
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • Beerten, Jef
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The modular multilevel converter (MMC) has emerged as the preferred choice for voltage source converter (VSC)-based high voltage direct current (HVDC) systems due to its low losses, low harmonic distortion, modularity, and redundancy. These advantages come at the expense of a complex control system with the strong coupling among its control variables, which complicates the design procedure of both its individual control loops and the DC link controllers. In fact, the performance improvement of a control loop could lead to degraded performance of other loops. Hence, to deal with such a complex dynamic system, this article suggests adopting multivariable H optimal control techniques in order to ensure stability and optimized performance of a VSC-HVDC link. First, a full-order, centralized multi-input-multi-output (MIMO) controller is derived based on H optimization and used as a benchmark for the system performance level. Then, a fixed-structure, decentralized MIMO controller is synthesized to make a compromise between the optimal performance and feasibility of practical implementation. Finally, simulations are conducted to evaluate and compare the performance and robustness degradation due to the migration from a high-order, centralized controller towards a low-order, decentralized controller., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Real-time optimization-based reference calculation integrated control for MMCs considering converter limitations

  • Westerman Spier, Daniel|||0000-0003-3477-6328
  • Rodríguez Bernuz, Joan Marc|||0000-0003-4503-379X
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • López Mestre, Joaquim
  • Junyent Ferré, Adrià
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The paper addresses a real-time optimization-based reference calculation integrated with a control structure for Modular Multilevel Converters (MMC) operating under normal and constrained situations (where it has reached current and/or voltage limitations, e.g. during system faults). The algorithm prioritizes to satisfy the Transmission System Operators (TSO) AC grid current demanded set-points. The constrained optimization problem is formulated based on the steady-state model of the MMC, whereby the prioritization is achieved through distinct weights defined in the Objective Function’s (OF) terms. The resultant optimization problem, however, is highly nonlinear requiring high computation burden to be solved in real-time. To overcome this issue, this paper applies a Linear Time-Varying (LTV) approximation, where the nonlinear dynamics of the system are represented as constant parameters, while a Linear Time-Invariant (LTI) system is used to formulate the optimization constraints. The converter's current references are determined in real-time by solving a constrained linearized optimization problem at each control time step, considering the TSO's demands, the current MMC operating point and its physical limitations. Finally, the linearized-optimization problem is integrated with the MMC controllers and evaluated under different network conditions, where the results indicated that method can be potentially employed to obtain the MMCs current references., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Improved current reference calculation for MMCs internal energy balancing control

  • Westerman Spier, Daniel|||0000-0003-3477-6328
  • Prieto-Araujo, E.
  • López Mestre, Joaquim
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The paper addresses an improved inner current reference calculation to be employed in the control of modular multilevel converters operating during either balanced or unbalanced conditions. The suggested reference calculation is derived based on the AC and DC additive and differential voltage components applied to the upper and lower arms of the converter. In addition, the impacts caused not only by the AC networks impedances but also by the MMCs arm impedances are also considered during the derivation of the AC additive current reference expressions. Another issue discussed in this article regards that singular voltage conditions, where the positive-sequence component is equal to the negative one, may occur not only in the AC network but also internally (within the converters applied voltages). Several different inner current reference calculation methods are compared and their applicability during the former fault conditions is analyzed. The paper presents a detailed formulation of the inner current reference calculation and applies it to different unbalanced AC grid faults where it is shown that the presented approach can be potentially used to maintain the internal energy of the converter balanced during normal and fault conditions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Modelling VSCs connected to weak grids

  • Orellana Montaño, Luis Carlos|||0000-0002-0615-3855
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • Sainz Sapera, Luis|||0000-0002-5670-0669
  • Cheah Mañé, Marc|||0000-0002-0942-661X
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
This paper addresses the oscillatory stability phenomena studied in the literature and reported by network operators in grid-connected VSC systems. Negative interactions have been observed at different frequencies in these systems, causing the tripping of power converters (e.g. wind turbines or HVDC applications). The interaction between the controller of power converters and poorly damped AC networks are identified causes of these events. This paper analyses two methods to model grid-connected VSC systems applied in the literature to study stability: the state-space and the impedance-based model. Validation has been carried out between the two methodologies by analyzing eigenvalues and singular values of the system. Furthermore, a time-domain simulation has been done to validate the state-space model with a non-linear MATLAB/Simulink model. The stability is studied in a base case system with a grid-connected VSC to the main AC grid via an LC circuit. A sensibility analysis of the strength of the grid and an analysis of subsynchronous and harmonic oscillatory resonances has been carried out for weak grids., Europe’s power system has seen significant changes in recent decades, notably the development of renewable energy sources. However, this transition is far from complete, and further changes are essential to make our energy system ready to play its part in realising the climate goals set at COP21. At present, renewable energy sources are increasing their share of electricity generation. This is particularly the case for offshore wind energy. InnoDC's 14 participants prepare 15 early career researchers to play their role in the energy transition that will take place over the next 20-40 years. The project focusses on the development of the electricity transmission system, targeting the connection of offshore wind, the integration of offshore wind with the existing power system (including the use of HVDC), and the operation of the future power system where large scale wind is connected to a hybrid AC and DC power system. Technological development for offshore wind is ongoing. This research project focusses on the models and methodologies for the integration of these new technologies (e.g. offshore wind turbines, VSC HVDC converters, long AC cables) into the power system. Challenges in these areas will be addressed in this project: firstly, these new devices behave inherently differently to traditional power system components. Secondly, the multi-actor/intersectoral nature of these systems means that they have distinct elements and devices interfacing with each other, each with limited information of the overall system. The project will train the researchers in developing prototype tools to aid the developers and users of these new energy systems. This training network aims to train the researchers of the future in the pivotal sector of renewable energy and grid technology, which is largely led by research and industry. This project prepares the researchers of tomorrow to maintain Europe’s position of leadership in renewable, smart energy and tackling climate change.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Dc voltage droop control design for mmc-based multiterminal hvdc grids

  • Dadjo Tavakoli, Saman
  • Sánchez Sánchez, Enric|||0000-0003-4075-0191
  • Prieto Araujo, Eduardo|||0000-0003-4349-5923
  • Gomis Bellmunt, Oriol|||0000-0002-9507-8278
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to, This article addresses the design of the DC voltage droop control in modular multilevel converter (MMC)-based multiterminal HVDC grids. First, two energy-based control approaches, namely classic and cross control, are explored for the implementation of the voltage-power droop controller. The cross control, as the better solution for droop implementation, is further improved, making it more robust against disturbances. Then, a methodology is derived to select the droop gain combinations considering the AC grid, DC grid and MMC dynamics and their limitations. The methodology is based on a linear analysis to identify the valid droop gains which comply with the limits imposed on: the transient power sharing among MMCs, the DC grid voltage, the MMC AC and DC currents, the total MMC stored energy, and the stability margin of the complete multiterminal HVDC grid. Finally, time-domain simulations are conducted using the nonlinear model to validate the dynamic performance of the selected droop combinations obtained from the suggested methodology., Peer Reviewed, Objectius de Desenvolupament Sostenible::7 - Energia Assequible i No Contaminant
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On resonance instabilities in VSCs connected to weak grids

  • Orellana Montaño, Luis Carlos
  • Prieto Araujo, Eduardo
  • Sainz Sapera, Luis
  • Cheah Mañé, Marc
  • Gomis Bellmunt, Oriol
This paper addresses the oscillatory stability phenomena studied in the literature and reported by network operators in grid-connected VSC systems. Negative interactions have been observed at different frequencies in these systems, causing the tripping of power converters (e.g. wind turbines or HVDC applications). The interaction between the controller of power converters and poorly damped AC networks are identified causes of these events. This paper analyses two methods to model grid-connected VSC systems applied in the literature to study stability: the state-space and the impedance-based model. Validation has been carried out between the two methodologies by analyzing eigenvalues and singular values of the system. Furthermore, a time-domain simulation has been done to validate the state-space model with a non-linear MATLAB/Simulink model. The stability is studied in a base case system with a grid-connected VSC to the main AC grid via an LC circuit. A sensibility analysis of the strength of the grid and an analysis of subsynchronous and harmonic oscillatory resonances has been carried out for weak grids., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Modelling VSCs connected to weak grids

  • Orellana Montaño, Luis Carlos
  • Prieto Araujo, Eduardo
  • Sainz Sapera, Luis
  • Cheah Mañé, Marc
  • Gomis Bellmunt, Oriol
This paper addresses the oscillatory stability phenomena studied in the literature and reported by network operators in grid-connected VSC systems. Negative interactions have been observed at different frequencies in these systems, causing the tripping of power converters (e.g. wind turbines or HVDC applications). The interaction between the controller of power converters and poorly damped AC networks are identified causes of these events. This paper analyses two methods to model grid-connected VSC systems applied in the literature to study stability: the state-space and the impedance-based model. Validation has been carried out between the two methodologies by analyzing eigenvalues and singular values of the system. Furthermore, a time-domain simulation has been done to validate the state-space model with a non-linear MATLAB/Simulink model. The stability is studied in a base case system with a grid-connected VSC to the main AC grid via an LC circuit. A sensibility analysis of the strength of the grid and an analysis of subsynchronous and harmonic oscillatory resonances has been carried out for weak grids., Europe’s power system has seen significant changes in recent decades, notably the development of renewable energy sources. However, this transition is far from complete, and further changes are essential to make our energy system ready to play its part in realising the climate goals set at COP21. At present, renewable energy sources are increasing their share of electricity generation. This is particularly the case for offshore wind energy. InnoDC's 14 participants prepare 15 early career researchers to play their role in the energy transition that will take place over the next 20-40 years. The project focusses on the development of the electricity transmission system, targeting the connection of offshore wind, the integration of offshore wind with the existing power system (including the use of HVDC), and the operation of the future power system where large scale wind is connected to a hybrid AC and DC power system. Technological development for offshore wind is ongoing. This research project focusses on the models and methodologies for the integration of these new technologies (e.g. offshore wind turbines, VSC HVDC converters, long AC cables) into the power system. Challenges in these areas will be addressed in this project: firstly, these new devices behave inherently differently to traditional power system components. Secondly, the multi-actor/intersectoral nature of these systems means that they have distinct elements and devices interfacing with each other, each with limited information of the overall system. The project will train the researchers in developing prototype tools to aid the developers and users of these new energy systems. This training network aims to train the researchers of the future in the pivotal sector of renewable energy and grid technology, which is largely led by research and industry. This project prepares the researchers of tomorrow to maintain Europe’s position of leadership in renewable, smart energy and tackling climate change., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Optimal current reference calculation for MMCs considering converter limitations

  • Westerman Spier, Daniel
  • Prieto-Araujo, E.
  • López Mestre, Joaquim
  • Gomis Bellmunt, Oriol
The paper addresses an optimization-based reference calculation method for Modular Multilevel Converters (MMC) operating in normal and constrained situations (when the converter needs to prioritize its quantities as it has reached voltage or current limitations, e.g. during system faults). The optimization problem prioritizes to satisfy the external AC active and reactive current set-points demanded by the grid operator through the corresponding grid code. If the operator demands are fulfilled, it uses the available MMC degrees of freedom to minimize the arm inductance losses. Otherwise, if the operator demanded AC set-points cannot be accomplished, the optimization attempts to minimize the error prioritizing between either AC active or reactive currents. The optimization problem constraints are imposed through a steady-state model considering simultaneously the external and internal AC and DC magnitudes of the converter. The steady-state model also includes the voltage variation in the equivalent arm capacitors (considering the ripple). Then, the imposed limitations are the maximum allowed grid and arm currents, the maximum allowed arm voltages and the sub-module capacitor maximum voltages. The paper presents a detailed formulation of the optimization problem and applies it to several case studies where it is shown that the presented approach can be potentially used to obtain the MMC references both in normal and fault conditions., Peer Reviewed, Postprint (updated version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Methodology for interaction identification in modular multi-level converter-based HVDC systems

  • Dadjo Tavakoli, Saman
  • Prieto Araujo, Eduardo
  • Sánchez Sánchez, Enric
  • Gomis-Bellmunt, Oriol
This paper suggests a methodology for the identification, classification, and evaluation of various types of interactions that may occur in an HVDC link based on modular multi-level converters (MMC). The methodology incorporates the most suitable analytic tools for the frequency-domain study of each interaction category. To do so, a detailed nonlinear model of an MMC-based HVDC link that consists of master and slave MMCs, AC grids, and the DC transmission system is derived. Then, it is linearized to obtain a multi-input multi-output (MIMO) linear model that represents the dynamics of the complete MMC-based HVDC link. Based on the control loops of interest, interactions are classified as (1) state variable interactions, (2) disturbance interactions, (3) control loop interactions, and (4) overall system interactions. Then, through the application examples, the mentioned four categories of interactions are studied in frequency domain via the relevant analytic tools. The results obtained from the frequency-domain analysis are validated by time-domain simulation., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Real-time optimization-based reference calculation integrated control for MMCs considering converter limitations

  • Westerman Spier, Daniel
  • Rodríguez Bernuz, Joan Marc
  • Prieto Araujo, Eduardo
  • López Mestre, Joaquim
  • Junyent Ferré, Adrià
  • Gomis Bellmunt, Oriol
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The paper addresses a real-time optimization-based reference calculation integrated with a control structure for Modular Multilevel Converters (MMC) operating under normal and constrained situations (where it has reached current and/or voltage limitations, e.g. during system faults). The algorithm prioritizes to satisfy the Transmission System Operators (TSO) AC grid current demanded set-points. The constrained optimization problem is formulated based on the steady-state model of the MMC, whereby the prioritization is achieved through distinct weights defined in the Objective Function’s (OF) terms. The resultant optimization problem, however, is highly nonlinear requiring high computation burden to be solved in real-time. To overcome this issue, this paper applies a Linear Time-Varying (LTV) approximation, where the nonlinear dynamics of the system are represented as constant parameters, while a Linear Time-Invariant (LTI) system is used to formulate the optimization constraints. The converter's current references are determined in real-time by solving a constrained linearized optimization problem at each control time step, considering the TSO's demands, the current MMC operating point and its physical limitations. Finally, the linearized-optimization problem is integrated with the MMC controllers and evaluated under different network conditions, where the results indicated that method can be potentially employed to obtain the MMCs current references., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Optimal H-infinity control design for MMC-based HVDC links

  • Dadjo Tavakoli, Saman
  • Fekriasl, Sajjad
  • Prieto Araujo, Eduardo
  • Beerten, Jef
  • Gomis Bellmunt, Oriol
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The modular multilevel converter (MMC) has emerged as the preferred choice for voltage source converter (VSC)-based high voltage direct current (HVDC) systems due to its low losses, low harmonic distortion, modularity, and redundancy. These advantages come at the expense of a complex control system with the strong coupling among its control variables, which complicates the design procedure of both its individual control loops and the DC link controllers. In fact, the performance improvement of a control loop could lead to degraded performance of other loops. Hence, to deal with such a complex dynamic system, this article suggests adopting multivariable H optimal control techniques in order to ensure stability and optimized performance of a VSC-HVDC link. First, a full-order, centralized multi-input-multi-output (MIMO) controller is derived based on H optimization and used as a benchmark for the system performance level. Then, a fixed-structure, decentralized MIMO controller is synthesized to make a compromise between the optimal performance and feasibility of practical implementation. Finally, simulations are conducted to evaluate and compare the performance and robustness degradation due to the migration from a high-order, centralized controller towards a low-order, decentralized controller., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Improved current reference calculation for MMCs internal energy balancing control

  • Westerman Spier, Daniel
  • Prieto-Araujo, E.
  • López Mestre, Joaquim
  • Gomis Bellmunt, Oriol
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The paper addresses an improved inner current reference calculation to be employed in the control of modular multilevel converters operating during either balanced or unbalanced conditions. The suggested reference calculation is derived based on the AC and DC additive and differential voltage components applied to the upper and lower arms of the converter. In addition, the impacts caused not only by the AC networks impedances but also by the MMCs arm impedances are also considered during the derivation of the AC additive current reference expressions. Another issue discussed in this article regards that singular voltage conditions, where the positive-sequence component is equal to the negative one, may occur not only in the AC network but also internally (within the converters applied voltages). Several different inner current reference calculation methods are compared and their applicability during the former fault conditions is analyzed. The paper presents a detailed formulation of the inner current reference calculation and applies it to different unbalanced AC grid faults where it is shown that the presented approach can be potentially used to maintain the internal energy of the converter balanced during normal and fault conditions., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Dc voltage droop control design for mmc-based multiterminal hvdc grids

  • Dadjo Tavakoli, Saman
  • Sánchez Sánchez, Enric
  • Prieto Araujo, Eduardo
  • Gomis Bellmunt, Oriol
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to, This article addresses the design of the DC voltage droop control in modular multilevel converter (MMC)-based multiterminal HVDC grids. First, two energy-based control approaches, namely classic and cross control, are explored for the implementation of the voltage-power droop controller. The cross control, as the better solution for droop implementation, is further improved, making it more robust against disturbances. Then, a methodology is derived to select the droop gain combinations considering the AC grid, DC grid and MMC dynamics and their limitations. The methodology is based on a linear analysis to identify the valid droop gains which comply with the limits imposed on: the transient power sharing among MMCs, the DC grid voltage, the MMC AC and DC currents, the total MMC stored energy, and the stability margin of the complete multiterminal HVDC grid. Finally, time-domain simulations are conducted using the nonlinear model to validate the dynamic performance of the selected droop combinations obtained from the suggested methodology., Peer Reviewed, Objectius de Desenvolupament Sostenible::7 - Energia Assequible i No Contaminant, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Steady-state analysis of the modular multilevel converter.

  • Westerman Spier, Daniel
  • López Mestre, Joaquim
  • Prieto Araujo, Eduardo
  • Gomis Bellmunt, Oriol
In this paper, the steady-state behavior of the modular multilevel converter (MMC) is studied under balanced and unbalanced AC grid voltage conditions. The suggested mathematical model is derived combining the converter internal arm variables and both AC and DC grids variables. Moreover, the steady-state solution of the system can be achieved by setting the internal power balance within the converter. In order to verify the steady-state model, different types of AC fault conditions are imposed, and the output values are compared with the simulation results of an average model of the MMC circuit. The results show that the proposed analysis is in close agreement with the simulations for all conditions evaluated, validating the developed equations., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Stability assessment for multi-infeed grid-connected VSCs modeled in the admittance matrix form

  • Orellana Montaño, Luis Carlos
  • Sainz Sapera, Luis
  • Prieto Araujo, Eduardo
  • Gomis Bellmunt, Oriol
© 2021 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting /republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works, The increasing use of power electronics converters to integrate renewable energy sources has been a subject of concern due to the resonance oscillatory phenomena caused by their interaction with poorly damped AC networks. Early studies are focused on assessing the controller influence of a single converter connected to simple networks, and they are no longer representative for existing systems. Lately, studies of multi-infeed grid-connected converters are of particular interest, and their main aim is to apply traditional criteria and identify their difficulties in the stability assessment. An extension of traditional criteria is commonly proposed as a result of these analysis, but they can be burdensome for large and complex power systems. The present work addresses this issue by proposing a simple criterion to assess the stability of large power systems with high-penetration of power converters. The criterion has its origin in the mode analysis and positive-net damping stability criteria, and it addresses the stability in the frequency domain by studying the eigenvalues magnitude and real component of dynamic models in the admittance matrix form. Its effectiveness is tested in two case studies developed in Matlab/Simulink which compare it with traditional criteria, proving its simplicity., Peer Reviewed, Postprint (author's final draft)