Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Analysis of supercritical carbon dioxide Brayton cycles for a helium-cooled pebble bed blanket DEMO-like fusion power plant

  • Hidalgo-Salaverri, Javier
  • Cano Megías, Pilar
  • Chacartegui, Ricardo
  • Ayllón Guerola, Juan Manuel
  • Viezzer, Eleonora
Nuclear fusion is expected to be a clean and almost-unlimited power source in the near future. The first net power demonstration plant (DEMO) is planned to start operation in 2050. The supercritical carbon dioxide (S-CO) Brayton cycle is an excellent candidate for integration with a fusion power plant, such as DEMO, because of its high efficiency at intermediate temperatures and low interaction of coolant with tritium. This work analyses a set of S-CO Brayton cycle layouts for its integration in a DEMO-like fusion power plant, considering the specific requirements and heat availability characteristics. A framework has been developed to integrate the PROCESS code and the numerical solver EES to study the thermal and economic aspects of integrating the different S-CO cycle layouts. In total, 14 layouts have been studied and grouped into a more conservative (DEMO1, pulsed operation) and more advanced (DEMO2, steady-state operation) fusion reactors. The PROCESS code has been used to obtain the DEMO 2018 Baseline, which defines the available power from each heat source and their boundary conditions. This code has also been used to assess the cost of the optimal layout. Thermal storage has been added to the DEMO1 scenario to avoid standby times that could negatively affect the cycle equipment lifetime and efficiency. Besides, these boundary conditions have been extended to account for possible technical improvements by the time of its construction in the DEMO2 scenario. A sensitivity analysis of the most characteristic parameters of the cycles shows a strong dependence on the turbine inlet temperature for all layouts, which is constrained by the reactor material limits. The cycle efficiency (electric power produced before consumptions non-related to the cycle) has been selected as the figure of merit for the optimisation. The results show a 38% cycle efficiency for DEMO1 and 56% for DEMO2 scenarios. These efficiencies drop to 20% and 38% values, respectively, when the reactor and cooling loop power consumptions are considered. These values are obtained for current fusion reactor conceptual designs. The economic analysis shows the economic viability of DEMO2 scenarios., The authors would like to thank J. Morris, M. Kovari and the rest of the PROCESS team of UKAEA for discussion and guidance on using the UKAEA systems code PROCESS for this work. The authors gratefully acknowledge the financial support of the Spanish Ministry of Science, Innovation and Universities (grant FPU17/06273), the H2020 Marie-Sklodowska Curie programme (grant agreement No. 708257) and the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme (grant agreement No. 805162).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design and simulation of an imaging neutral particle analyzer for the ASDEX Upgrade tokamak

  • Rueda-Rueda, José
  • García-Muñoz, M.
  • Viezzer, Eleonora
  • Schneider, P. A.
  • García-Domínguez, J.
  • Ayllón Guerola, Juan Manuel
  • Galdón Quiroga, Joaquín
  • Herrmann, A.
  • Du, X. D.
  • Zeeland, M. A. van
  • Oyola, Pedro
  • Rodríguez-Ramos, M.
  • ASDEX Upgrade Team
An Imaging Neutral Particle Analyzer (INPA) diagnostic has been designed for the ASDEX Upgrade (AUG) tokamak. The AUG INPA diagnostic will measure fast neutrals escaping the plasma after charge exchange reactions. The neutrals will be ionized by a 20 nm carbon foil and deflected toward a scintillator by the local magnetic field. The use of a neutral beam injector (NBI) as an active source of neutrals will provide radially resolved measurements, while the use of a scintillator as an active component will allow us to cover the whole plasma along the NBI line with unprecedented phase-space resolution (<12 keV and 8 cm) and a fast temporal response (up to 1 kHz with the high resolution acquisition system and above 100 kHz with the low resolution one), making it suitable to study localized fast-ion redistributions in phase space., This project received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (Grant Agreement No. 805162) and the Spanish Ministerio de Ciencia, Innovación y Universidades (Grant No. FPU19/02486).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design and simulation of an imaging neutral particle analyzer for the ASDEX Upgrade tokamak

  • Rueda-Rueda, José
  • García-Muñoz, M.
  • Viezzer, Eleonora
  • Schneider, P. A.
  • García-Domínguez, J.
  • Ayllón Guerola, Juan Manuel
  • Galdón Quiroga, Joaquín
  • Herrmann, A.
  • Du, X. D.
  • Zeeland, M. A. van
  • Oyola, Pedro
  • Rodríguez-Ramos, M.
  • ASDEX Upgrade Team
An Imaging Neutral Particle Analyzer (INPA) diagnostic has been designed for the ASDEX Upgrade (AUG) tokamak. The AUG INPA diagnostic will measure fast neutrals escaping the plasma after charge exchange reactions. The neutrals will be ionized by a 20 nm carbon foil and deflected toward a scintillator by the local magnetic field. The use of a neutral beam injector (NBI) as an active source of neutrals will provide radially resolved measurements, while the use of a scintillator as an active component will allow us to cover the whole plasma along the NBI line with unprecedented phase-space resolution (<12 keV and 8 cm) and a fast temporal response (up to 1 kHz with the high resolution acquisition system and above 100 kHz with the low resolution one), making it suitable to study localized fast-ion redistributions in phase space., This project received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (Grant Agreement No. 805162) and the Spanish Ministerio de Ciencia, Innovación y Universidades (Grant No. FPU19/02486).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hardware developments and commissioning of the imaging heavy ion beam probe at ASDEX upgrade

  • Birkenmeier, Gregor
  • Galdón Quiroga, Joaquín
  • Olevskaia, V.
  • Oyola, Pedro
  • Toledo Garrido, Juan José
  • Bald, K.
  • Sochor, M.
  • Anda, Gábor
  • Zoletnik, S.
  • Herrmann, A.
  • Rodhe, V.
  • Teschke, Mathias
  • Giannone, L.
  • Lunt, T.
  • Viezzer, Eleonora
  • García-Muñoz, M.
  • ASDEX Upgrade Team
The imaging heavy ion beam probe (i-HIBP) is a new diagnostic concept realized at the tokamak ASDEX Upgrade (AUG) in order to obtain two-dimensional information about the density, the magnetic field and the electrostatic potential at the plasma edge. Although the two main components of the i-HIBP, an alkali beam based injector and a scintillator based detector, involve well-developed technologies, further developments were necessary to realize the i-HIBP at AUG. In dedicated laboratory tests, a new type of cesium source was characterized and the neutralization efficiency and properties of the primary cesium beam were found to be similar to alkali beams made of lighter elements. The use of cesium had also impact on the choice of the scintillator material, which was experimentally investigated in terms of photon yield, energy dependence and degradation revealing significant differences under irradiation with cesium ions compared to irradiation with hydrogenic beams. Due to constrictions of the AUG experiment setup, the high voltage components, the in-vessel shutter technology and the maintenance capabilities of the i-HIBP required new developments for the commissioning of the diagnostic., This work received funding from the Helmholtz Association under grant no. VH-NG-1350. This work received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 805162). This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014–2018 and 2019–2020 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetic equilibrium design for the SMART tokamak

  • Doyle, Scott J.
  • López-Aires, D.
  • Mancini, Alessio
  • Agredano-Torres, Manuel
  • García-Sánchez, J. L.
  • Segado-Fernández, Jorge
  • Ayllón Guerola, Juan Manuel
  • García-Muñoz, M.
  • Viezzer, Eleonora
  • Soria-Hoyo, C.
  • García López, J.
  • Cunningham, Geoffrey
  • Buxton, Peter F.
  • Gryaznevich, Mikhail P.
  • Hwang, Y. S.
  • Chung, Kyoung-Jin
The SMall Aspect Ratio Tokamak (SMART) device is a new compact (plasma major radius R≥0.40 m, minor radius a≥0.20 m, aspect ratio A≥1.7) spherical tokamak, currently in development at the University of Seville. The SMART device has been designed to achieve a magnetic field at the plasma center of up to B=1.0 T with plasma currents up to I=500 kA and a pulse length up to τ=500 ms. A wide range of plasma shaping configurations are envisaged, including triangularities between −0.50≤δ≤0.50 and elongations of κ≤2.25. Control of plasma shaping is achieved through four axially variable poloidal field coils (PF), and four fixed divertor (Div) coils, nominally allowing operation in lower-single null, upper-single null and double-null configurations. This work examines phase 2 of the SMART device, presenting a baseline reference equilibrium and two highly-shaped triangular equilibria. The relevant PF and Div coil current waveforms are also presented. Equilibria are obtained via an axisymmetric Grad-Shafranov force balance solver (Fiesta), in combination with a circuit equation rigid current displacement model (RZIp) to obtain time-resolved vessel and plasma currents., The authors would like to thank the VEST team for their technical and engineering support. This work received funding from the Fondo Europeo de Desarollo Regional (FEDER) by the European Commission under grant agreement numbers IE17-5670 and US-15570. In addition support from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 805162) is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimizing beam-ion confinement in ITER by adjusting the toroidal phase of the 3D magnetic fields applied for ELM control

  • Sanchís Sánchez, Lucía
  • García-Muñoz, M.
  • Viezzer, Eleonora
  • Loarte, E.
  • Li, L.
  • Liu, Y. Q.
  • Snicker, A.
  • Chen, L.
  • Zonca, F.
  • Pinches, S. D.
The confinement of neutral beam injection (NBI) particles in the presence of n = 3 resonant magnetic perturbations (RMPs) in 15 MA ITER DT plasmas has been studied using full orbit ASCOT simulations. Realistic NBI distribution functions, and 3D wall and equilibria, including the plasma response to the externally applied 3D fields calculated with MARS-F, have been employed. The observed total fast-ion losses depend on the poloidal spectra of the applied n = 3 RMP as well as on the absolute toroidal phase of the applied perturbation with respect to the NBI birth distribution. The absolute toroidal phase of the RMP perturbation does not affect the ELM control capabilities, which makes it a key parameter in the confinement optimization. The physics mechanisms underlying the observed fast-ion losses induced by the applied 3D fields have been studied in terms of the variation of the particle canonical angular momentum (δP φ ) induced by the applied 3D fields. The presented simulations indicate that the transport is located in an edge resonant transport layer as observed previously in ASDEX upgrade studies. Similarly, our results indicate that an overlapping of several linear and nonlinear resonances at the edge of the plasma might be responsible for the observed fast-ion losses. The results presented here may help to optimize the RMP configuration with respect to the NBI confinement in future ITER discharges.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Single and double null equilibria in the SMART Tokamak

  • Doyle, Scott J.
  • Mancini, Alessio
  • Agredano-Torres, Manuel
  • Segado-Fernández, Jorge
  • Ayllón Guerola, Juan Manuel
  • García-Muñoz, M.
  • Viezzer, Eleonora
  • García López, J.
  • Hwang, Y. S.
  • Chung, Kyoung-Jin
The SMall Aspect Ratio Tokamak (SMART) device is a novel, compact (R = 0.42 m, a = 0.22 m, A 1.70) spherical tokamak, currently under development at the University of Seville. The SMART device is being developed over 3 phases, with target on-axis toroidal magnetic fields between 0.1 ≼ B ≼ 1.0 T, and target plasma currents of between 35 ≼ I ≼ 400 kA; with phases 2 and 3 enabling access to a wide range of elongations (κ ≼ 2.30) and triangularities (− 0.50 ≼ δ ≼ 0.50). SMART employs four internal divertor coils with two internal and two external poloidal field coils, enabling operation in lower-single, upper-single and double-null configurations. This work examines phase 3 of the SMART device, presenting a prospective L-mode discharge scenario without external heating, before examining five highly-shaped equilibria, including: two double null triangular configurations, two single null triangular configurations and a baseline double null configuration. All equilibria are obtained via an axisymmetric Grad-Shafranov force balance solver (Fiesta), in combination with a circuit equation rigid current displacement model (RZIp) to obtain time-resolved vessel and plasma currents., The authors would like to thank the VEST team for their technical and engineering support. This work received funding from the Fondo Europeo de Desarollo Regional (FEDER) by the European Commission under grant agreement numbers IE17-5670 and US-15570. In addition support from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 805 162) is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characterization of scintillator screens under irradiation of low energy 133Cs ions

  • Toledo Garrido, Juan José
  • Galdón Quiroga, Joaquín
  • Viezzer, Eleonora
  • Birkenmeier, Gregor
  • Olevskaia, V.
  • Balden, M.
  • García López, J.
  • Jiménez-Ramos, M. C.
  • Rodríguez-Ramos, M.
  • Anda, Gábor
  • Videla-Trevin, Micaela
  • García-Muñoz, M.
  • ASDEX Upgrade Team
An imaging heavy ion beam probe (i-HIBP) diagnostic, for the simultaneous measurement of plasma density, magnetic field and electrostatic potential in the plasma edge, has been installed at ASDEX Upgrade. Unlike standard heavy ion beam probes, in the i-HIBP the probing (heavy) ions are collected by a scintillator detector, creating a light pattern or strike-line, which is then imaged by a camera. Therefore, a good characterization of the scintillator response is needed. Previous works focused on the scintillator behaviour against irradiation with light ions such as hydrogen and alpha particles. In this work we present the characterization of several scintillator screens - TG-Green (SrGa2S4:Eu2+), YAG-Ce (Y3Al5O12:Ce3+) and P11 (ZnS:Ag) - against irradiation with 133Cs+ ions, in an energy range between 5 and 70 keV and ion currents between 105 and 107 ions/(s·cm2). Three main properties of the scintillators have been studied: the ionolumenescence efficiency or yield, the linearity and the degradation as a function of the fluence. The highest yield was delivered by the TG-Green scintillator screen with > 8·103 photons/ion at 50 keV. All the samples showed a linear response with increasing incident ion flux. The degradation was quantified in terms of the fluence F1/2, which leads to a reduction of the emissivity by a factor of 2. TG-Green showed the lowest degradation with F1/2= 5.4·1014 ions/cm2. After the irradiation the samples were analyzed by Scanning Electron Microscopy (SEM), Rutherford Backscattering Spectrometry (RBS) and Particle Induced X-ray Emission (PIXE). No trace of Cs was found in the irradiated regions. These results indicate that, among the tested materials, TG-Green is the best candidate for the i-HIBP detector., This work received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 805162). G. Birkenmeier acknowledges funding from the Helmholtz Association under grant no. VHNG-1350. J. Galdon-Quiroga acknowledges funding from the Spanish Ministry of Science and Innovation under grant no. FJC2019-041092-I.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Imaging Neutral Particle Analyzer Engineering Design and Installation for the ASDEX Upgrade Tokamak

  • García-Domínguez, J.
  • Rueda-Rueda, José
  • Viezzer, Eleonora
  • Schneider, P. A.
  • Ayllón Guerola, Juan Manuel
  • García-Muñoz, M.
  • Hidalgo-Salaverri, Javier
  • Mancini, Alessio
  • Videla-Trevin, Micaela
  • Herrmann, A.
An imaging neutral particle analyzer (INPA) has been installed in the ASDEX Upgrade (AUG) tokamak to provide simultaneous measurements of the radial profile and the energy of the confined fast-ion (FI) population. The INPA diagnostic leverages the advantages of neutral particle analyzers (NPAs) and FI loss detectors (FILDs) by measuring charge exchange (CX) neutrals ionized by an ultrathin carbon foil is deflected into a scintillator by the local magnetic field. The design of this diagnostic has been developed under a series of constraints, such as the lack of space and hazardous environment (high level of neutron and gamma radiation), the need of high precision in the alignment of the nonsequential optical system (with six optical axes), and the optimization of the scintillator plate (signal emitter). To this end, a modular and adjustable design has been pursued with several degrees of freedom to ensure precise positioning during the installation and optical calibration. The induced electromagnetic and thermal stresses have been assessed and compared against the material limits of the detector, showing that no significant stress is expected for the system. The thermal analysis shows that the diagnostic scintillator can work efficiently during normal operation conditions. The CAD design, a comparison between the synthetic and real optical signals and the mechanical assessment [based on finite element analysis (FEA)], is presented in this contribution., 10.13039/100010663-European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (Grant Number: 805162) 10.13039/100014440-Spanish Ministerio de Ciencia, Innovación y Universidades (Grant Number: FPU19/02486)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Predictive simulations for plasma scenarios in the SMART tokamak

  • Mancini, Alessio
  • Velarde, Lina
  • Viezzer, Eleonora
  • Cruz-Zabala, D.J.
  • Rivero-Rodriguez, J.F.
  • García-Muñoz, M.
  • Sanchís Sánchez, Lucía
  • Snicker, A.
  • Segado-Fernández, Jorge
  • García-Domínguez, J.
  • Hidalgo-Salaverri, Javier
  • Cano Megías, Pilar
  • Toscano-Jimenez, M.
The SMall Aspect Ratio Tokamak (SMART) is a new spherical machine that is currently being constructed at the University of Seville (Mancini et al., 2021; Agredano-Torres et al., 2021). The operation of SMART will cover three different phases reaching an inductive plasma current (IP) of more than 500 kA, a toroidal magnetic field (BT) of 1 T and a pulse length of 500 ms (Mancini et al., 2021; Agredano-Torres et al., 2021). The main goal of the SMART tokamak is to study high plasma confinement regimes in a broad triangularity range (-0.5≤δ≤0.5) (Doyle et al., 2021; Doyle et al., 2021). While in phase 1 the ohmic heating alone is expected to provide enough power to access the H-mode, in phase 2 and phase 3 the access to the H-mode will be ensured by applying Neutral Beam Injection (NBI) as external heating system. The NBI will consist of one injector at 25 keV and 1 MW of power. The overall design of the NBI, including injection geometry, energy and power have been optimized using the ASCOT5 code (Hirvijoki et al., 2021). The SMART scenarios have been developed with the help of the free boundary equilibrium solver code FIESTA (Cunningham, 2013) coupled to the linear time independent, rigid plasma model RZIP (Lazarus et al., 1990) to calculate the target equilibria for all the different operational phases. To assess the feasibility of those scenarios, predictive modelling needs to be included to evaluate properly the evolution of the temperatures, density profiles for both electrons and ions. To this extent, the 1.5D transport code ASTRA (Pereverzev and Yushmanov, 2002) has been used including models for the ohmic current, bootstrap current and current driven by NBI. This contribution discusses the electron and ion density and temperature profiles obtained for various scenarios for phase 1 and 2 and presents the design study of the NBI., his work received funding from the Fondo Europeo de Desarollo Regional (FEDER) by the European Commission under grant agreement numbers IE17-5670 and US-15570. The authors gratefully acknowledge the financial support of the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 805162)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Velocity-space analysis of fast-ion losses measured in MAST-U using a high-speed camera in the FILD detector

  • Velarde, Lina
  • Rivero-Rodriguez, J.F.
  • Galdón Quiroga, Joaquín
  • Williams, T.
  • Rueda-Rueda, José
  • Cano Megías, Pilar
  • Chacartegui, Ricardo
  • García-Muñoz, M.
  • Blackmore, S.
  • McClements, K. G.
  • Sanchís Sánchez, Lucía
  • Viezzer, Eleonora
A fast-ion loss detector (FILD) was installed for the first time at the mega amp spherical tokamak—upgrade (MAST-U) spherical tokamak during its upgrade in 2021. A new CMOS camera was installed in the MAST-U FILD acquisition system to provide high spatial resolution (1.1 MPx) with an acquisition frequency of up to 3.5 kHz. This camera has enabled the systematic analysis of the velocity-space of the fast-ion losses measured in MAST-U presented in this manuscript. The main parameters that determine the FILD measurement have been analysed to maximise the signal in the detector: the orbit-following code ASCOT predicts an inverse relation between the FILD signal and the probe’s relative distance to the separatrix. This prediction has been validated experimentally, enabling the measurement of fast-ion losses in the flat-top phase of the discharge; furthermore, ASCOT simulations show a big impact of the edge safety factor (q95) on the toroidal deposition of the prompt losses, indicating that the signal in the MAST-U FILD can be maximised by running scenarios with | q 95 | < 6 . This prediction was validated experimentally by a scan in the toroidal magnetic field. The experimental resolution of the MAST-U FILD has been evaluated for a typical MAST-U scenario with 750 kA plasma current. The results show that the diagnostic resolution is in the order of 0.5 to 1 degree in pitch angle, and of 1 to 3 cm in gyroradius in current scenarios. A systematic analysis of the velocity-space of the losses shows that the measured gyroradii of the prompt losses match those of the neutral beam injector injection energies within the resolution of the diagnostic. The experimentally measured pitch angles have been compared with ASCOT simulations, and it has been found that the agreement is better for scenarios heated with the on-axis beam, since this beam enables measurements of the magnetic field pitch angle. This analysis has been applied to a discharge where type-III ELM-induced fast-ion losses were measured, showing that the ELMs result in an increase in the FILD signal, and that the losses are coming from passing orbits., This work has been carried out within the framework of the EUROfusion Consortium, funded by the European Union via the Euratom Research and Training Programme (Grant Agreement No. 101052200—EUROfusion) and from the EPSRC [Grant No. EP/W006839/1]. This research received funding from the Plan Andaluz de Investigación, Desarrollo e Innovación (PAIDI 2020, No. 003456/A02W), Consejería de Transformación Económica, Industria, Conocimiento y Universidades de la Junta de Andalucía. This project has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme (Grant Agreement No. 805162). J Galdon-Quiroga acknowledges support from the MSCA PF programme under Grant No. 101069021., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hybrid kinetic-MHD simulations of ELMs with fast-ion kinetic effects in the ASDEX Upgrade tokamak

  • Dominguez-Palacios, J.
  • García-Muñoz, M.
  • Viezzer, Eleonora
  • Futatani, S.
  • Toscano-Jimenez, M.
  • González-Martín, Javier
  • Galdón Quiroga, Joaquín
  • Jansen van Vuuren, A.
  • Oyola, Pedro
  • Rueda-Rueda, José
  • Sanchís Sánchez, Lucía
  • Suzuki, Y.
  • Todo, Y.
This paper is part of the Special Collection: Papers from the 67th Annual Meeting of the APS Division of Plasma Physics, Paper NI3 4, Bull. Am. Phys. Soc. 70 (2025)., Hybrid kinetic-magnetohydrodynamic (MHD) simulations of edge-localized modes (ELMs) in the ASDEX Upgrade tokamak with the initial value code MEGA are presented in this manuscript and show that, when the fast-ion pressure becomes comparable to the MHD drive, the resulting imbalance between fast-ion and MHD forces increases the mode frequency, reaching values consistent with those observed experimentally in ELM crashes in the presence of fast-ions. First, we provide a detailed description of the numerical setup of MEGA to calculate plasma dynamics at the edge. Subsequently, the MHD module of MEGA is used to simulate the ELM crash without fast-ions, observing the plasma filaments that are ejected from the plasma region, with the consequence of the flattening of the driving sources. Next, systematic scans of the fast-ion parameter space are performed to understand fast-ion effects on ELMs. For core-localized fast-ion distributions, the ELM is unaltered and, after the ELM crash, an energetic particle mode is excited. In the presence of fast-ions at the plasma edge, the ELM crash is characterized by modes that become radially broader and with higher frequencies for increasing fast-ion birth energy., This work received funding from the Spanish Ministry of Science (Grant Nos. FPU17/05703 and PID2020-116822RB-I00). This work received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program (Grant Agreement No. 805162). This work was supported by the NINS program of Promoting Research by Networking among Institutions. This work has been carried out within the framework of the EUROfusion Consortium, funded by the European Union via the Euratom Research and Training Program (Grant Agreement No. 101052200—EUROfusion). This work was co-funded by the European Regional Development Fund (Andalusian Operational Program 2014–2020) and by the Ministry of Economic Transformation, Industry, Knowledge and Universities of the Junta de Andalucía within the framework of the PAIDI project with Ref. No. P18-FR-3812. The authors gratefully acknowledge the computer resources of the RES (Spanish Supercomputing Network) at MareNostrum and the technical support provided by the Barcelona Supercomputing Center (BSC), and the support from Marconi-Fusion, the High Performance Computer at the CINECA headquarters in Bologna (Italy) for its provision of supercomputer resources., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

MHD stability analysis against pressure and current-driven modes in the SMall Aspect Ratio Tokamak

  • Dominguez Palacios, Jesus
  • Garcia Muñoz, Manuel
  • Toscano Jimenez, Manuel
  • Liu, Yueqiang
  • Mancini, Alessio
  • Cruz Zabala, Diego Jose
  • Berkery, John
  • Labbate, John A.
  • Parisi, Jason
  • Todo, Yasushi
  • Reyner Viñolas, Alex
  • Podestà, Mario
  • Viezzer, Eleonora
  • Oyola Dominguez, Pablo
  • Futatani, Shimpei|||0000-0001-5742-5454
Linear magnetohydrodynamic (MHD) simulations for the SMall Aspect Ratio Tokamak (SMART) have been carried out for the first time, for both positive (PT) and negative triangularity (NT) shaped plasmas using the MARS-F code. The MHD stability of projected SMART plasmas against internal kinks, infernal modes and edge peeling-ballooning modes have been analyzed for a wide range of realistic equilibria. A stabilization of internal kinks and infernal modes is observed when increasing the safety factor profile and reducing plasma beta. PT shaped plasmas are more stable against both internal kinks and infernal modes than their counterpart NT shaped plasmas. Toroidal flows have little impact on the MHD stability of the internal kinks, but they have a strong stabilizing effect on infernal modes, which can be further mitigated in NT shaped plasmas. The MHD stability of peeling-ballooning modes is reduced in NT shaped plasmas, as observed in conventional tokamaks., This work received funding from the Spanish Ministry ofScience (Grant Nos. FPU17/05703 and PID2020-116822RB-I00) and from the European Research Council (ERC) underthe European Union’s Horizon 2020 research and innov-ation programme (Grant Agreement No. 805162). Thiswork was supported by the NINS program of PromotingResearch by Networking among Institutions. This work wasco-funded by the European Regional Development Fund(Andalusian Operational Programme 2014 – 2020) and by theMinistry of Economic Transformation, Industry, Knowledgeand Universities of the Junta de Andalucía within theframework of the PAIDI project with reference P18-FR-3812. This work has been carried out within the frameworkof the EUROfusion Consortium, funded by the EuropeanUnion via the Euratom Research and Training Programme(Grant Agreement No 101052200 – EUROfusion). Viewsand opinions expressed are however those of the author(s)only and do not necessarily reflect those of the EuropeanUnion or the European Commission. Neither the EuropeanUnion nor the European Commission can be held respons-ible for them. Additional support was provided by the U.S.Department of Energy under Contract Number DE-ACO2-09CH11466 (PPPL), as well as the Science UndergraduateLaboratory Internship (SULI) program. The authors grate-fully acknowledge the computer resources of RES (Spanish13 Nucl. Fusion64(2024) 126028J. Dominguez-Palacioset alSupercomputing Network) at MareNostrum and the tech-nical support provided by Barcelona Supercomputing Center(BSC), as well as those of CICA (Centro InformáticoCientífico de Andalucía). The authors gratefully acknowledgethe help of Oak Nelson with the BALOO code.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

MHD stability analysis against pressure and current-driven modes in the SMall Aspect Ratio Tokamak

  • Dominguez Palacios, Jesus
  • Garcia Muñoz, Manuel
  • Toscano Jimenez, Manuel
  • Liu, Yueqiang
  • Mancini, Alessio
  • Cruz Zabala, Diego Jose
  • Berkery, John
  • Labbate, John A.
  • Parisi, Jason
  • Todo, Yasushi
  • Reyner Viñolas, Alex
  • Podestà, Mario
  • Viezzer, Eleonora
  • Oyola Dominguez, Pablo
  • Futatani, Shimpei
Linear magnetohydrodynamic (MHD) simulations for the SMall Aspect Ratio Tokamak (SMART) have been carried out for the first time, for both positive (PT) and negative triangularity (NT) shaped plasmas using the MARS-F code. The MHD stability of projected SMART plasmas against internal kinks, infernal modes and edge peeling-ballooning modes have been analyzed for a wide range of realistic equilibria. A stabilization of internal kinks and infernal modes is observed when increasing the safety factor profile and reducing plasma beta. PT shaped plasmas are more stable against both internal kinks and infernal modes than their counterpart NT shaped plasmas. Toroidal flows have little impact on the MHD stability of the internal kinks, but they have a strong stabilizing effect on infernal modes, which can be further mitigated in NT shaped plasmas. The MHD stability of peeling-ballooning modes is reduced in NT shaped plasmas, as observed in conventional tokamaks., This work received funding from the Spanish Ministry ofScience (Grant Nos. FPU17/05703 and PID2020-116822RB-I00) and from the European Research Council (ERC) underthe European Union’s Horizon 2020 research and innov-ation programme (Grant Agreement No. 805162). Thiswork was supported by the NINS program of PromotingResearch by Networking among Institutions. This work wasco-funded by the European Regional Development Fund(Andalusian Operational Programme 2014 – 2020) and by theMinistry of Economic Transformation, Industry, Knowledgeand Universities of the Junta de Andalucía within theframework of the PAIDI project with reference P18-FR-3812. This work has been carried out within the frameworkof the EUROfusion Consortium, funded by the EuropeanUnion via the Euratom Research and Training Programme(Grant Agreement No 101052200 – EUROfusion). Viewsand opinions expressed are however those of the author(s)only and do not necessarily reflect those of the EuropeanUnion or the European Commission. Neither the EuropeanUnion nor the European Commission can be held respons-ible for them. Additional support was provided by the U.S.Department of Energy under Contract Number DE-ACO2-09CH11466 (PPPL), as well as the Science UndergraduateLaboratory Internship (SULI) program. The authors grate-fully acknowledge the computer resources of RES (Spanish13 Nucl. Fusion64(2024) 126028J. Dominguez-Palacioset alSupercomputing Network) at MareNostrum and the tech-nical support provided by Barcelona Supercomputing Center(BSC), as well as those of CICA (Centro InformáticoCientífico de Andalucía). The authors gratefully acknowledgethe help of Oak Nelson with the BALOO code., Postprint (published version)