Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical assessment of RANS and LES modelling in particle separation devices

  • Bahramian, Linda
  • Amani, Ahmad|||0000-0001-5197-2879
  • Muela Castro, Jordi|||0000-0003-1583-8490
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
In the present work, the separation efficiency analysis on particle-laden flows in the framework of LES and RANS modelling for an Inertial Particle Separator (IPS) device has been presented. The comparison of LES and RANS will allow us to study and assess both the advantages and disadvantages of these modelling techniques for the design and optimisation purposes of IPS devices. The results show that RANS modelling can yield similar results on the aggregate level with a comparably lower computational cost., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTection devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI_B 01205). Carles Oliet, as a Serra Húnter lecturer, acknowledges the Catalan Government for the support through this Programme
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Study of the conservation properties in two-way coupled dispersed multiphase flows using finite volume methods

  • Bahramian, Linda
  • Muela Castro, Jordi|||0000-0003-1583-8490
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
In order to simulate dispersed multiphase flows, the coupling level must be determined according to the volume fraction in the system. The volume fraction is the ratio of the total volume of the dispersed phases over the total volume of the flow. In dilute flows, with volume fractions smaller than 10 -6 , only the influence of carrier phase over the dispersed phase is considered which is known as one-way coupling. Nonetheless, in dispersed flows with higher volume fractions, the effect of the dispersed phase over the continuous one should be taken into consideration, known as two-way coupling. This effect normally is applied as a source term in the conservation equations of the carrier phase. Depending on the numerical method and the discrete operators employed, these source terms can lead to some issues when aiming to preserve physical properties like mass, momentum or kinetic energy. Moreover, in order to validate the two-way coupling method, a particle-laden turbulent flow benchmark case with a mass loading of 22% is simulated by means of large eddy numerical simulation (LES). The aim of this work is to study the conservation properties of dispersed multiphase flows like momentum and kinetic energy through two-way coupling between dispersed and continuous phases., This research was supported by the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund (FI AGAUR Grant). This work has also been developed within the EU H2020 Clean Sky 2 Joint Undertaking (JU) research project “A New proTection devIce for FOD – ANTIFOD” (grant agreement Nº 821352)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical Study of an Inertial Particle Separator Efficiency Under the Effect of Ice Accretion Caused by the Water Impingement

  • Bahramian, Linda
  • Amani, Ahmad|||0000-0001-5197-2879
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
The inertial particle separator (IPS) can face ice accretion due to the impingement of super-cooled water droplets on its inner surface. This work studies a numerical study using Computational Fluid Dynamics (CFD) for the ice accretion inside an IPS. This study is crucial in investigating the IPS performance that is affected by ice accretion. First, the numerical simulation of ice accretion for a simpler geometry, a cylinder, is validated with the experimental data. Then, the simulation of water impingement and ice accretion is studied for an IPS device. The ice profiles for different wall sections of the IPS show that ice accumulates on the bent surface of the shroud, the windward side of the hub, and the leading edge of the splitter. This accumulated ice changes the geometry of the IPS. Therefore, the separation efficiency of the IPS is expected to decrease due to the generation of ice in the way of the scavenge outlet., Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205), and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme. This project has received funding from the Clean Sky 2 Joint Undertaking under the European Union’s Horizon 2020 research and innovation programme under grant agreement No 821352 (ANTIFOD project).
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical assessment of parcel modeling in large eddy simulation for dispersed multiphase flows

  • Bahramian, Linda
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
The particle-laden turbulent flow benchmark case of a confined jet by Hishida (1987) was selected for validation purposes of the Eulerian-Lagrangian method in Large Eddy Simulation (LES). After validation, a particle size distribution was determined and the streamwise particle velocities in three different parcel models were studied; the Number Fixed Model (NFM), the Volume Fixed Model (VFM) and the hybrid parcel model, a combination of these two previous models. The purpose behind introducing a new hybrid parcel model was to optimize the computational cost of the simulation versus the accuracy. Results show that this hybrid model presents better agreement and fewer discrepancies in the mean and the Root Mean Square (RMS) velocity profiles for the small particle diameters compared to the VFM and also for the large particle diameters compared to the NFM. In the next step, a Langevin stochastic model for subgrid dispersion of Lagrangian particles was implemented to analyze its effect on the particle turbulent statistics. For this purpose, the subgrid Stokes number of different classes of particles was analyzed to shed more light on the impact of using the stochastic subgrid model for this case. It has shown that the effect of the applied stochastic subgrid model in the RMS velocities of the dispersed phase of the current case was negligible., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTec-tion devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial sup-port from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A numerical study on turbulent flow in an Inertial Particle Separator device

  • Bahramian, Linda
  • Amani, Ahmad|||0000-0001-5197-2879
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
An Inertia Particle Separator (IPS) is a device situated in the intake of the aircraft to remove particles from entering the engine; consisting of two types of outlets: core and scavenge. This work presents the numerical simulation of the Reynolds-Average Navier-Stokes (RANS) and the Large Eddy Simulation (LES) approach for an IPS. First, the fluid comparison of RANS and LES is carried out for three cases. Results show that the profile velocities of the continuous phase for RANS and LES are in good agreement. In the following, the separation efficiency is analyzed through different Reynolds numbers (Re) of 52K, 83K and 110K and coreto-scavenge mass flow rate ratios (ß = 0.10,0.12,0.18) for two types of particles with diameters of d p = 10µm and d p = 120µm. The elastic particle-wall collision is considered here. The particles with the smallest Stokes number (St <<1) show the smallest separation efficiency because they follow the flow pattern. Their separation efficiency decreases in lower flow split values. Also, decreasing the Re decreases the separation efficiency for the particle diameter of 10 µm. The particles with 120 µm have a separation efficiency almost near one, which does not change with decreasing the flow split. The discrepancies in separation efficiency between RANS and LES show up in the small particles where these particles are affected by the flow unsteadiness. In contrast, RANS can predict the separation efficiency correctly for the particles with large inertia and Stokes numbers (St >> 1)., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTection devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical analysis of parcel tracking in large eddy simulation of polydispersed multiphase flows: assessment of different parcel modeling techniques

  • Bahramian, Linda
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
In order to assess the impacts of parcel modeling, the Eulerian-Lagrangian method, by using the Particle-In-Cell model, is implemented for a three-dimensional polydispersed two-phase turbulent flow. First, the benchmark case of a confined jet presented by Hishida (1987) is used for validation. After determining a particle size distribution, the hybrid parcel model, which is a combination of two standard parcel models: the Number Fixed Model (NFM) and the Volume Fixed Model (VFM), has been designed based on the Sauter Mean Diameter (SMD). Later on, the velocity profiles of the dispersed phase were compared for these three parcel models. This comparison will allow us to study and assess the capacities and lacks regarding these parcel modeling techniques for design and optimization targets of different applications of dispersed multiphase flows. Results show that for the small particle sizes, the hybrid parcel model presents favorable agreement and fewer differences in the mean and the Root Mean Square (RMS) particle velocity profiles compared to the VFM, and in comparison to the NFM, this parcel model shows fewer discrepancies in particle velocity profiles for the large particle sizes., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTection devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Assessment of numerical aspects using LES in particle separation devices

  • Muela Castro, Jordi|||0000-0003-1583-8490
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Numerical simulations can be a powerful tool for the design and optimization of Foreign Object Debris (FOD) protection and separation devices. This work aims to study the relevance and influence of different modelling and numerical aspects in simulations of FOD devices using Large Eddy Simulation (LES) modelling. The results show that in LES some numerical aspects can be critical and must be carefully considered aiming to obtain accurate and reliable results. It is presented how some models affect the physics of the phenomena involved in these kind of flows as well as their impact on the accuracy of the simulations., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Advanced techniques for grau area mitigation in DES simulations and their effectes on the subsonic round jet acoustic spectra, Tècniques avançades per la mitigació de la zona grisa en simulacions DES i els seus efectes en l'espectre acústic del jet circular

  • Duben, Alexey
  • Ruano Pérez, Jesús|||0000-0002-5121-2543
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
The research dedicated to the investigation of different gray-area mitigation approaches towards accurate aerodynamics and aeroacoustics is presented. The recent modifications of hybrid RANS-LES DDES approach based on combinations of new adapting subgrid length scales (~ !, SLA and lsq) and LES models ( and S3QR) are considered. The object of investigation is an immersed subsonic turbulent jet. The simulations are carried out on a set of refining meshes using two different scale-resolving numerical algorithms realized in the compressible codes NOISEtte and OpenFOAM. The evaluation of different approaches is focused on the analysis of far field noise. The results show that all the considered techniques provide appropriate accuracy to predict the noise generated by the turbulent jet. The study clearly demonstrated the importance of both numerical scheme and subgrid turbulence model. The peculiarities of considered approaches are revealed and discussed., A.D. was supported by Moscow Center for Fundamental and Applied Mathematics, Agreement with the Ministry of Science and Higher Education of the Russian Federation, No. 075-15-2019-1623. The NOISEtte computations were carried out using the equipment of the shared research facilities of HPC computing resources at Lomonosov Moscow State University and the computing resources of the federal collective usage center Complex for Simulation and Data Processing for Mega-science Facilities at NRC ”Kurchatov Institute” (http://ckp.nrcki.ru/). J.Ru. was supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain. J.Ru. and F.X.T. have been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.Ru., F.X.T. and J.Ri. are also supported by the Clean Sky 2 Joint Undertaking. ANTIFOD project (Grant ID 821352)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On the validation of numerical simulation with experimental results on compressible turbulent flow in an inertial particle separator device

  • Bahramian, Linda
  • Amani, Ahmad|||0000-0001-5197-2879
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
To remove particles from entering the engine or Environmental Control System (ECS), an Inertial Particle Separator (IPS) can be situated in the intake. In IPS, a rapid change in flow direction is induced, and particles separate from the core outlet because of their inertia. Small particles with a low Stokes number (St) follow the flow and often enter the core outlet, while the large particles with a high St are thrown into the scavenge by their high inertia. Accurately capturing the unsteadiness of the fluid is crucial, especially with low scavenge mass flow fraction for the particles with low St. The numerical simulation of the compressible flow is validated here, implementing the 3D Improved Delayed Detached Eddy Simulation (IDDES) and the Reynolds-averaged Navier-Stokes (RANS) methods against experimental data. It is shown that the IDDES method can capture correctly the unsteadiness of the flow. After validation of the fluid phase, the particle separation efficiency was studied for different particle diameters using these turbulence numerical methods along with three different ambient temperatures: standard, hot, and cold. The separation efficiency values were in agreement with the experimental data., Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme. This project has received funding from the Clean Sky 2 Joint Undertaking under the European Union’s Horizon 2020 research and innovation programme under grant agreement No 821352 (ANTIFOD project).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical assessment of parcel modeling in large eddy simulation for dispersed multiphase flows

  • Bahramian, Linda
  • Trias Miquel, Francesc Xavier
  • Oliet Casasayas, Carles
  • Pérez Segarra, Carlos David
The particle-laden turbulent flow benchmark case of a confined jet by Hishida (1987) was selected for validation purposes of the Eulerian-Lagrangian method in Large Eddy Simulation (LES). After validation, a particle size distribution was determined and the streamwise particle velocities in three different parcel models were studied; the Number Fixed Model (NFM), the Volume Fixed Model (VFM) and the hybrid parcel model, a combination of these two previous models. The purpose behind introducing a new hybrid parcel model was to optimize the computational cost of the simulation versus the accuracy. Results show that this hybrid model presents better agreement and fewer discrepancies in the mean and the Root Mean Square (RMS) velocity profiles for the small particle diameters compared to the VFM and also for the large particle diameters compared to the NFM. In the next step, a Langevin stochastic model for subgrid dispersion of Lagrangian particles was implemented to analyze its effect on the particle turbulent statistics. For this purpose, the subgrid Stokes number of different classes of particles was analyzed to shed more light on the impact of using the stochastic subgrid model for this case. It has shown that the effect of the applied stochastic subgrid model in the RMS velocities of the dispersed phase of the current case was negligible., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTec-tion devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial sup-port from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Advanced techniques for grau area mitigation in DES simulations and their effectes on the subsonic round jet acoustic spectra, Tècniques avançades per la mitigació de la zona grisa en simulacions DES i els seus efectes en l'espectre acústic del jet circular

  • Duben, Alexey
  • Ruano Pérez, Jesús
  • Trias Miquel, Francesc Xavier
  • Rigola Serrano, Joaquim
The research dedicated to the investigation of different gray-area mitigation approaches towards accurate aerodynamics and aeroacoustics is presented. The recent modifications of hybrid RANS-LES DDES approach based on combinations of new adapting subgrid length scales (~ !, SLA and lsq) and LES models ( and S3QR) are considered. The object of investigation is an immersed subsonic turbulent jet. The simulations are carried out on a set of refining meshes using two different scale-resolving numerical algorithms realized in the compressible codes NOISEtte and OpenFOAM. The evaluation of different approaches is focused on the analysis of far field noise. The results show that all the considered techniques provide appropriate accuracy to predict the noise generated by the turbulent jet. The study clearly demonstrated the importance of both numerical scheme and subgrid turbulence model. The peculiarities of considered approaches are revealed and discussed., A.D. was supported by Moscow Center for Fundamental and Applied Mathematics, Agreement with the Ministry of Science and Higher Education of the Russian Federation, No. 075-15-2019-1623. The NOISEtte computations were carried out using the equipment of the shared research facilities of HPC computing resources at Lomonosov Moscow State University and the computing resources of the federal collective usage center Complex for Simulation and Data Processing for Mega-science Facilities at NRC ”Kurchatov Institute” (http://ckp.nrcki.ru/). J.Ru. was supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain. J.Ru. and F.X.T. have been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.Ru., F.X.T. and J.Ri. are also supported by the Clean Sky 2 Joint Undertaking. ANTIFOD project (Grant ID 821352)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical assessment of RANS and LES modelling in particle separation devices

  • Bahramian, Linda
  • Amani, Ahmad
  • Muela Castro, Jordi
  • Rigola Serrano, Joaquim
  • Oliet Casasayas, Carles
  • Pérez Segarra, Carlos David
In the present work, the separation efficiency analysis on particle-laden flows in the framework of LES and RANS modelling for an Inertial Particle Separator (IPS) device has been presented. The comparison of LES and RANS will allow us to study and assess both the advantages and disadvantages of these modelling techniques for the design and optimisation purposes of IPS devices. The results show that RANS modelling can yield similar results on the aggregate level with a comparably lower computational cost., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTection devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI_B 01205). Carles Oliet, as a Serra Húnter lecturer, acknowledges the Catalan Government for the support through this Programme, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Study of the conservation properties in two-way coupled dispersed multiphase flows using finite volume methods

  • Bahramian, Linda
  • Muela Castro, Jordi
  • Pérez Segarra, Carlos David
In order to simulate dispersed multiphase flows, the coupling level must be determined according to the volume fraction in the system. The volume fraction is the ratio of the total volume of the dispersed phases over the total volume of the flow. In dilute flows, with volume fractions smaller than 10 -6 , only the influence of carrier phase over the dispersed phase is considered which is known as one-way coupling. Nonetheless, in dispersed flows with higher volume fractions, the effect of the dispersed phase over the continuous one should be taken into consideration, known as two-way coupling. This effect normally is applied as a source term in the conservation equations of the carrier phase. Depending on the numerical method and the discrete operators employed, these source terms can lead to some issues when aiming to preserve physical properties like mass, momentum or kinetic energy. Moreover, in order to validate the two-way coupling method, a particle-laden turbulent flow benchmark case with a mass loading of 22% is simulated by means of large eddy numerical simulation (LES). The aim of this work is to study the conservation properties of dispersed multiphase flows like momentum and kinetic energy through two-way coupling between dispersed and continuous phases., This research was supported by the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund (FI AGAUR Grant). This work has also been developed within the EU H2020 Clean Sky 2 Joint Undertaking (JU) research project “A New proTection devIce for FOD – ANTIFOD” (grant agreement Nº 821352)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On the validation of numerical simulation with experimental results on compressible turbulent flow in an inertial particle separator device

  • Bahramian, Linda
  • Amani, Ahmad
  • Rigola Serrano, Joaquim
  • Oliet Casasayas, Carles
  • Pérez Segarra, Carlos David
To remove particles from entering the engine or Environmental Control System (ECS), an Inertial Particle Separator (IPS) can be situated in the intake. In IPS, a rapid change in flow direction is induced, and particles separate from the core outlet because of their inertia. Small particles with a low Stokes number (St) follow the flow and often enter the core outlet, while the large particles with a high St are thrown into the scavenge by their high inertia. Accurately capturing the unsteadiness of the fluid is crucial, especially with low scavenge mass flow fraction for the particles with low St. The numerical simulation of the compressible flow is validated here, implementing the 3D Improved Delayed Detached Eddy Simulation (IDDES) and the Reynolds-averaged Navier-Stokes (RANS) methods against experimental data. It is shown that the IDDES method can capture correctly the unsteadiness of the flow. After validation of the fluid phase, the particle separation efficiency was studied for different particle diameters using these turbulence numerical methods along with three different ambient temperatures: standard, hot, and cold. The separation efficiency values were in agreement with the experimental data., Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme. This project has received funding from the Clean Sky 2 Joint Undertaking under the European Union’s Horizon 2020 research and innovation programme under grant agreement No 821352 (ANTIFOD project)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical analysis of parcel tracking in large eddy simulation of polydispersed multiphase flows: assessment of different parcel modeling techniques

  • Bahramian, Linda
  • Trias Miquel, Francesc Xavier
  • Oliet Casasayas, Carles
  • Pérez Segarra, Carlos David
In order to assess the impacts of parcel modeling, the Eulerian-Lagrangian method, by using the Particle-In-Cell model, is implemented for a three-dimensional polydispersed two-phase turbulent flow. First, the benchmark case of a confined jet presented by Hishida (1987) is used for validation. After determining a particle size distribution, the hybrid parcel model, which is a combination of two standard parcel models: the Number Fixed Model (NFM) and the Volume Fixed Model (VFM), has been designed based on the Sauter Mean Diameter (SMD). Later on, the velocity profiles of the dispersed phase were compared for these three parcel models. This comparison will allow us to study and assess the capacities and lacks regarding these parcel modeling techniques for design and optimization targets of different applications of dispersed multiphase flows. Results show that for the small particle sizes, the hybrid parcel model presents favorable agreement and fewer differences in the mean and the Root Mean Square (RMS) particle velocity profiles compared to the VFM, and in comparison to the NFM, this parcel model shows fewer discrepancies in particle velocity profiles for the large particle sizes., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTection devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical Study of an Inertial Particle Separator Efficiency Under the Effect of Ice Accretion Caused by the Water Impingement

  • Bahramian, Linda
  • Amani, Ahmad
  • Rigola Serrano, Joaquim
  • Oliet Casasayas, Carles
  • Pérez Segarra, Carlos David
The inertial particle separator (IPS) can face ice accretion due to the impingement of super-cooled water droplets on its inner surface. This work studies a numerical study using Computational Fluid Dynamics (CFD) for the ice accretion inside an IPS. This study is crucial in investigating the IPS performance that is affected by ice accretion. First, the numerical simulation of ice accretion for a simpler geometry, a cylinder, is validated with the experimental data. Then, the simulation of water impingement and ice accretion is studied for an IPS device. The ice profiles for different wall sections of the IPS show that ice accumulates on the bent surface of the shroud, the windward side of the hub, and the leading edge of the splitter. This accumulated ice changes the geometry of the IPS. Therefore, the separation efficiency of the IPS is expected to decrease due to the generation of ice in the way of the scavenge outlet., Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205), and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme. This project has received funding from the Clean Sky 2 Joint Undertaking under the European Union’s Horizon 2020 research and innovation programme under grant agreement No 821352 (ANTIFOD project)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Assessment of numerical aspects using LES in particle separation devices

  • Muela Castro, Jordi
  • Rigola Serrano, Joaquim
  • Oliet Casasayas, Carles
  • Pérez Segarra, Carlos David
  • Oliva Llena, Asensio
Numerical simulations can be a powerful tool for the design and optimization of Foreign Object Debris (FOD) protection and separation devices. This work aims to study the relevance and influence of different modelling and numerical aspects in simulations of FOD devices using Large Eddy Simulation (LES) modelling. The results show that in LES some numerical aspects can be critical and must be carefully considered aiming to obtain accurate and reliable results. It is presented how some models affect the physics of the phenomena involved in these kind of flows as well as their impact on the accuracy of the simulations., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A numerical study on turbulent flow in an Inertial Particle Separator device

  • Bahramian, Linda
  • Amani, Ahmad
  • Rigola Serrano, Joaquim
  • Oliet Casasayas, Carles
  • Pérez Segarra, Carlos David
An Inertia Particle Separator (IPS) is a device situated in the intake of the aircraft to remove particles from entering the engine; consisting of two types of outlets: core and scavenge. This work presents the numerical simulation of the Reynolds-Average Navier-Stokes (RANS) and the Large Eddy Simulation (LES) approach for an IPS. First, the fluid comparison of RANS and LES is carried out for three cases. Results show that the profile velocities of the continuous phase for RANS and LES are in good agreement. In the following, the separation efficiency is analyzed through different Reynolds numbers (Re) of 52K, 83K and 110K and coreto-scavenge mass flow rate ratios (ß = 0.10,0.12,0.18) for two types of particles with diameters of d p = 10µm and d p = 120µm. The elastic particle-wall collision is considered here. The particles with the smallest Stokes number (St <<1) show the smallest separation efficiency because they follow the flow pattern. Their separation efficiency decreases in lower flow split values. Also, decreasing the Re decreases the separation efficiency for the particle diameter of 10 µm. The particles with 120 µm have a separation efficiency almost near one, which does not change with decreasing the flow split. The discrepancies in separation efficiency between RANS and LES show up in the small particles where these particles are affected by the flow unsteadiness. In contrast, RANS can predict the separation efficiency correctly for the particles with large inertia and Stokes numbers (St >> 1)., This work has been developed within the EU H2020 Clean Sky 2 research project “A New proTection devIce for FOD - ANTIFOD” (grant agreement Nº 821352). Linda Bahramian acknowledges the financial support from the Secretariat of Universities and Research of the Generalitat de Catalunya and the European Social Fund, FI AGAUR Grant (2019 FI B 01205) and the UPC-Santander Grant. Carles Oliet, as a Serra Húnter associate professor, acknowledges the Catalan Government for the support through this Programme., Postprint (published version)