Pasar al contenido principal

ALGORITMOS NUMERICOS AVANZADOS PARA LA MEJORA DE LA EFICIENCIA ENERGETICA EN LOS SECTORES EOLICO Y SOLAR-TERMICO: DESARROLLO/ADAPTACION A NUEVAS ARQUITECTURAS COMPUTACIONALES

ENE2017-88697-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 90
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A method for fluid-structure interaction problems with non-Newtonian fluid

  • Amani, Ahmad|||0000-0001-5197-2879
  • Naseri, Alireza|||0000-0002-8650-5434
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
  • Oliva Llena, Asensio|||0000-0002-2805-4794
This paper represents a numerical method to solve fluid-structure interaction (FSI) problems where the fluid exhibits a non-Newtonian Viscoelastic behaviour. Oldroyd-B constitutive equation is used to model Viscoelastic fluid. For FSI solution, a semi-implicit partitioned method is used which separates the fluid pressure term and strongly couples it to the structure, while the remaining fluid terms are only weakly coupled. Numerical tests demonstrate the capability of the method to solve FSI problems with a non-Newtonian Viscoelastic behaviour of the fluid., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

NUMA-Aware strategies for the efficient execution of CFD simulations on CPU supercomputers

  • Álvarez Farré, Xavier|||0000-0002-1684-7658
  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The growing variety of computing architectures and the hybridization of high-performance computing systems encourage the research for portable implementations of numerical methods in simulation codes. However, the pursuit of efficient and portable implementations is a rather complex problem. The present work is devoted to the development of portable parallel algorithms, primarily for scale-resolving, time-accurate simulations of incompressible flows with turbulent heat and mass transfer. The heterogeneous computing capability allows for engaging both processors and accelerators efficiently. In addition to computing on accelerators, special attention is paid at efficiency on multiprocessor nodes with significant non-uniform memory access factor. In this work, we study in detail the parallel efficiency and performance for different execution modes on up to ten thousand cores of MareNostrum 4 supercomputer., The work has been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency. X. A. F. is supported by a predoctoral contract (2019FI B2-00076) by the Government of Catalonia. The work has been carried out using the computing resources of the Barcelona Supercomputing Center (MareNostrum 4); The authors thankfully acknowledge the institution., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the implementation of flux limiters in algebraic frameworks

  • Valle Marchante, Nicolás|||0000-0003-2140-041X
  • Álvarez Farré, Xavier|||0000-0002-1684-7658
  • Gorobets, Andrei
  • Castro González, Jesús|||0000-0002-8943-2402
  • Oliva Llena, Asensio|||0000-0002-2805-4794
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
The use of flux limiters is widespread within the scientific computing community to capture shock dis- continuities and are of paramount importance for the temporal integration of high-speed aerodynamics, multiphase flows and hyperbolic equations in general. Meanwhile, the breakthrough of new computing architectures and the hybridization of supercomputer systems pose a huge portability challenge, particularly for legacy codes, since the computing subroutines that form the algorithms, the so-called kernels, must be adapted to various complex parallel program- ming paradigms. From this perspective, the development of innovative implementations relying on a minimalist set of kernels simplifies the deployment of scientific computing software on state-of-the-art supercomputers, while it requires the reformulation of algorithms, such as the aforementioned flux lim- iters. Equipped with basic algebraic topology and graph theory underlying the classical mesh concept, a new flux limiter formulation is presented based on the adoption of algebraic data structures and kernels. As a result, traditional flux limiters are cast into a stream of only two types of computing kernels: sparse matrix-vector multiplication and generalized pointwise binary operators. The newly proposed formulation eases the deployment of such a numerical technique in massively parallel, potentially hybrid, computing systems and is demonstrated for a canonical advection problem., The work of N. V. and X. Á. F. has been supported by the Government of Catalonia, FI AGAUR predoctoral grants 2019FI_B2_ 000104 and 2019FI_B2_00076. N. V., X. Á. F., J. C., A. O. and F. X. T. have been funded by the Spanish Research Agency, ANUMESOL project ENE2017-88697-R. J. C. has also been funded by Spanish Research Agency, GALIFLOW project ENE2015-70662-P. The studies of this work have been carried out using the MareNostrum 4 supercomputer of the Barcelona Supercomput- ing Center, projects IM-2019-3-0026 and IM-2020-1-0006; the TSUBAME3.0 supercomputer of the Global Scientific Information and Computing Center at Tokyo Institute of Technology; the Lomonosov-2 supercomputer of the shared research facilities of HPC computing resources at Lomonosov Moscow State University; the K-60 hybrid cluster of the collective use center of the Keldysh Institute of Applied Mathematics; the JFF cluster of the Heat and Mass Transfer Technological Center at Technical University of Cat- alonia. The authors thankfully acknowledge these institutions for the compute time and technical support., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On a Proper Tensorial Subgrid Heat Flux Model

  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Dabbagh, Firas|||0000-0001-8440-507X
  • Santos Serrano, Daniel|||0000-0002-9179-4701
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
In this work, we aim to shed light to the following research question: can we find a nonlinear tensorial subgrid-scale (SGS) heat flux model with good physical and numerical properties, such that we can obtain satisfactory predictions for buoyancy-driven turbulent flows? This is motivated by our findings showing that the classical (linear) eddy-diffusivity assumption, q eddy ¿ ¿T, fails to provide a reasonable approximation for the actual SGS heat flux, q = uT - uT: namely, a priori analysis for airfilled Rayleigh-Bénard convection (RBC) clearly shows a strong misalignment. In the quest for more accurate models, we firstly study and confirm the suitability of the eddy-viscosity assumption for RBC carrying out a posteriori tests for different models at very low Prandtl numbers (liquid sodium, Pr = 0.005) where no heat flux SGS activity is expected. Then, different (nonlinear) tensor-diffusivity SGS heat flux models are studied a priori using DNS data of an air-filled (Pr = 0.7) RBC at Rayleigh numbers up to 1011. Apart from having good alignment trends with the actual SGS heat flux, we also restrict ourselves to models that are numerically stable per se and have the proper cubic near-wall behavior. This analysis leads to a new family of SGS heat flux models based on the symmetric positive semi-definite tensor GGT where G = ¿u, i.e. q ¿ GGT¿T, and the invariants of the GGT tensor. Finally, relevant numerical aspects regarding the implementation of this type of models are discussed in detail. A list of physical and numerical properties is identified and subsequently imposed, leading to a symmetrypreserving discretization that is based on discrete operators already available in any CFD code., F.X.T., F.D. and A.O. have been financially supported by the Ministerio de Economía y Competitividad, Spain, ANUMESOL project (ENE2017-88697-R). F.X.T. and A.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722). F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). D.S. is supported by an FI AGAUR-Generalitat de Catalunya fellowship (2020FI B 00839). Calculations have been performed on the IBM MareNostrum 4 supercomputer at the BSC (PRACE 15th Call, Ref. 2016163972, “Exploring new frontiers in Rayleigh-Bénard convection” and Tier-1 RES projects IM-2020-2-0029 & IM-2020-3-0030 “Direct and Large-Eddy Simulation of buoyancy-driven turbulence in liquid metals”). The authors thankfully acknowledge these institutions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Assessment of LES techniques for mitigating the Grey Area in DDES models

  • Pont Vilchez, Arnau|||0000-0001-9068-3076
  • Santos Serrano, Daniel|||0000-0002-9179-4701
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Duben, Alexey
  • Revell, Alistair
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The slow RANS-LES transition is a well-known shortcoming in hybrid turbulence models such as DelayedDetached Eddy Simulation (DDES). The present work assesses the feasibility of 2D sensitive LES models for naturally triggering turbulence, rather than using the specifically designed techniques available in the literature. This research has been carried out with OpenFOAM, which has been used for simulating the flow in a Backward-Facing Step configuration. The results have been compared with a DNS data set, showing the good mitigation capabilities of such LES techniques. Nevertheless, other cases should be studied before extracting any relevant conclusion., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017- 88697-R). A.P.V. is supported by a FI-DGR 2016 predoctoral contract (No. 2018FI_B2_00072) financed by Generalitat de Catalunya, Spain. F.X.T. is supported by a Ramón y Cajal postdoctoral Contract (No. RYC-2012-11996) financed by the Ministerio de Economía y Competitividad, Spain., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On a physically-consistent nonlinear subgrid-scale heat flux model for LES of buoyancy driven flows

  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Dabbagh, Firas|||0000-0001-8440-507X
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Small-scale dynamics is the spirit of turbulence physics. It delivers complex mechanisms when turbulence is purely sustained by buoyancy. This takes place in Rayleigh-Bénard convection (RBC). Most of the existing RBC dynamics is ruled by hard turbulent regime and a deep understanding of small scale dynamics with its relevant nonlinearities, is still unsatis¿ed. To do so, the evolution of QG =-1/2tr(G2) and RG =-1/3tr(G3), invariants of the velocity gradient tensor, G = Gradu u u, in their phase space{QG,RG}, were studied and reported in Dabbagh et al. [1] using DNS of RBC. In the present work, we expand this 2D {QG,RG} evolution to 3D by decomposing RG into its strain production RS = -1/3tr(S3) andenstrophyproductiontr(¿2S) =RS-RG terms, where S and ¿ aretherate-of-strainandrate-of-rotation tensors, respectively. In the {QG,RS,RS-RG} space, the ¿ow topology in a Lagrangian evolution is changing by the conditionalmeantrajectories(CMTs){DQG/Dt,DRS/Dt,D(RS-RG)/Dt}. Usingthedatasetin[1],andfromFigure46: anidenti¿edcyclicalstartoftrajectoriesisdistinguishedinareasofvortex-stretchingRS-RG >0andRS >0inthestrain dominated slots (QG < 0), which becomes stronger and longer expanded at Rayleigh number Ra = 1010. Afterwards, the trajectories move downwards (QG << 0) in areas of vortex-compression RS-RG < 0 and RS > 0, that also become more diverging at Ra = 1010 as a result of the self-ampli¿ed straining [1]. This is followed by rising trajectories upwards (QG > 0) to continue performing the typical planner {QG,RG} cyclical behaviour [1], next to RS = 0, and decaying towards the origin. DNS at Ra = 1011 is currently being computed on the MareNostrum supercomputer [2]. Results will be presented during the conference., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Investigating the capabilities of CFD-based data-driven models for indoor environmental design and control

  • Morozova, Nina
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Capdevila Paramio, Roser|||0000-0003-2569-2544
  • Oliva Llena, Asensio|||0000-0002-2805-4794
In this work, we study the accuracy of CFD-based data-driven models, which predict comfort-related flow parameters in a ventilated cavity with a heated floor. We compare the computational cost and accuracy of three different models, namely artificial neural network, support vector regression, and gradient boosting regression. The tested scenarios include short and long cavities with different inlet velocities. Among the studied frameworks, the artificial neural network provides the most accurate predictions for most of the tested flow configurations. However, test configurations with jet separation and a secondary vortex are more difficult to predict correctly; thus more high-fidelity data is required in order to construct a more robust and reliable model., This work is supported by the Ministerio de Economía y Competitividad, Spain [ENE2017-88697-R]. N. Morozova is supported by the by the Ministerio de Economía y Competitividad, Spain [FPU16/06333 predoctoral contract]. Part of the calculations was performed on the MareNostrum 4 supercomputer at the Barcelona Supercomputing Center [RES project IM-2021-1-0015]. The authors thankfully acknowledge these institutions.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Tetrahedral adaptive mesh refinement for two-phase flows using conservative level-set method

  • Antepara Zambrano, Óscar|||0000-0002-4596-0289
  • Balcázar Arciniega, Néstor|||0000-0003-0776-2086
  • Oliva Llena, Asensio|||0000-0002-2805-4794
In this article, we describe a parallel adaptive mesh refinement strategy for two-phase flows using tetrahedral meshes. The proposed methodology consists of combining a conservative level-set method with tetrahedral adaptive meshes within a finite volume framework. Our adaptive algorithm applies a cell-based refinement technique and adapts the mesh according to physics-based refinement criteria defined by the two-phase application. The new adapted tetrahedral mesh is obtained from mesh manipulations of an input mesh: operations of refinement and coarsening until a maximum level of refinement is achieved. For the refinement method of tetrahedral elements, geometrical characteristics are taking into consideration to preserve the shape quality of the subdivided elements. The present method is used for the simulation of two-phase flows, with surface tension, to show the capability and accuracy of 3D adapted tetrahedral grids to bring new numerical research in this context. Finally, the applicability of this approach is shown in the study of the gravity-driven motion of a single bubble/droplet in a quiescent viscous liquid on regular and complex domains., This work has been financially supported by the Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación, Spain (ENE2017-88697-R), and by Termo Fluids S.L. Oscar Antepara acknowledges financial support in form of a doctoral scholarship DI-14-06886 of the Ministerio de Economía y Competitividad and 2015DI-68 of the Secretaria d’ Universitats i Recerca del Departament d’Economia i Coneixement de la Generalitat de Catalunya, Spain. Néstor Balcázar acknowledges financial support of the Programa Torres Quevedo, Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación (PTQ-14-07186), Spain. Three-dimensional simulations were carried out using computer time provided by PRACE 14th Call (Project 2016153612) and RES project(FI-2018-1-0025) through the MareNostrum IV supercomputer based in Barcelona, Spain. We acknowledge Santander Supercomputacion support group at the University of Cantabria who provided access to the supercomputer Altamira Supercomputer at the Institute of Physics of Cantabria (IFCA-CSIC), member of the Spanish Supercomputing Network, for performing simulations/analyses (RES project FI-2018-3-0037)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

DNS of unequal size droplets collision using a moving-mesh/level-set method

  • Amani, Ahmad|||0000-0001-5197-2879
  • Balcázar Arciniega, Néstor|||0000-0003-0776-2086
  • Gutierrez, Enrique
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The dynamics of binary droplets collision is of huge importance in different fields, from multiphase reactors (Dudukovic et al in Chem Eng Sci 54:1975–1995, 1999 [11]), raindrop formation, ink-jet printing, spray combustion, emulsion stability, turbine blade cooling, spray coating (Ashgriz and Poo in J Fluid Mech 221:183–204, 1990 [5]), and to drug delivery. Due to the complexity of the nature of droplets collision, this topic is one of the most challenging areas in the field of fluid dynamics., We acknowledge Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación, Spain (ENE2017-88697-R). A. Amani acknowledges the financial support of (AGAUR) of Generalitat de Catalunya research scholarship (2016 FI_B 01059). N. Balcázar acknowledges the Programa Torres Quevedo MINECO (PTQ-14-07186).
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A General Method to Compute Numerical Dispersion Error

  • Ruano Pérez, Jesús|||0000-0002-5121-2543
  • Baez Vidal, Aleix|||0000-0003-4227-1768
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
This article presents a new methodology to compute numerical dispersion error. The analysis here presented is not restricted to uniform structured meshes nor linear discrete operators as it does not rely on sinusoids to compute the associated error. When using uniform meshes, the results obtained with the present method collapse onto the obtained with the classic one via an easy change of basis. If non-uniform meshes are used, a new kind of results are obtained which shed some light onto the role stretching has on dispersion error., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.R.P. is supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A scalable framework for the partitioned solution of fluid-structure interaction problems

  • Naseri, Alireza|||0000-0002-8650-5434
  • Totounferoush, Amin
  • González Acedo, Ignacio|||0000-0001-5679-1073
  • Mehl, Miriam
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
In this work, we present a scalable and efficient parallel solver for the partitioned solution of fluid–structure interaction problems through multi-code coupling. Two instances of an in-house parallel software, TermoFluids, are used to solve the fluid and the structural sub-problems, coupled together on the interface via the preCICE coupling library. For fluid flow, the Arbitrary Lagrangian–Eulerian form of the Navier–Stokes equations is solved on an unstructured conforming grid using a second-order finite-volume discretization. A parallel dynamic mesh method for unstructured meshes is used to track the moving boundary. For the structural problem, the nonlinear elastodynamics equations are solved on an unstructured grid using a second-order finite-volume method. A semi-implicit FSI coupling method is used which segregates the fluid pressure term and couples it strongly to the structure, while the remaining fluid terms and the geometrical nonlinearities are only loosely coupled. A robust and advanced multi-vector quasi-Newton method is used for the coupling iterations between the solvers. Both the fluid and the structural solver use distributed-memory parallelism. The intra-solver communication required for data update in the solution process is carried out using non-blocking point-to-point communicators. The inter-code communication is fully parallel and point-to-point, avoiding any central communication unit. Inside each single-physics solver, the load is balanced by dividing the computational domain into fairly equal blocks for each process. Additionally, a load balancing model is used at the inter-code level to minimize the overall idle time of the processes. Two practical test cases in the context of hemodynamics are studied, demonstrating the accuracy and computational efficiency of the coupled solver. Strong scalability test results show a parallel efficiency of 83% on 10,080 CPU cores., This work was financially supported by—Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación, Spain (ENE2017-88697-R),—priority program 1648—Software for Exascale Computing 214 (ExaFSA - Exascale Simulation of Fluid–Structure–Acoustics Interactions) of the German Research Foundation,—and a FI Ph.D. scholarship by the Agència de Gestió d’Ajuts Universitaris i de Recerca (AGAUR) of Generalitat de Catalunya (Spain). The performance measurements were carried out on the SuperMUC supercomputer at Leibniz Rechenzentrum (LRZ) der Bayerischen Akademie der Wissenschaften. The authors wish to thank LRZ for the computing time and the technical support., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A new general method to compute dispersion errors on Cartesian stretched meshes for both linear and non-linear operators

  • Ruano Pérez, Jesús|||0000-0002-5121-2543
  • Baez Vidal, Aleix|||0000-0003-4227-1768
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
The present article presents a new analysis for the dispersion error and the methodology to evaluate it numerically. Here we present the spectral properties of several convective schemes, including non-linear ones, on Cartesian stretched grids for linear advection problems. Results obtained with this method when applied to uniform structured meshes, converge to the results obtained with the classical method for all the studied schemes. Additionally, effects on the time step depending on which scheme is used are considered using the proposed method. The extracted conclusions taken into account both errors and computational cost allow to propose an optimal scheme according to the selected meshing strategy., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.R.P. is supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain. F.X.T. was supported by a Ramón y Cajal postdoctoral Contract (No. RYC-2012-11996) financed by the Ministerio de Economía y Competitividad, Spain., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Proper SGS heat flux models and numerical methods for LES

  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Santos Serrano, Daniel|||0000-0002-9179-4701
  • Dabbagh, Firas|||0000-0001-8440-507X
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
In this work, we aim to shed light to the following research question: can we find a nonlinear tensorial subgrid-scale (SGS) heat flux model with good physical and numerical properties, such that we can obtain satisfactory predictions for buoyancy-driven turbulent flows? This is motivated by our findings showing that the classical (linear) eddy-diffusivity assumption fails to provide a reasonable approximation for the actual SGS heat flux: namely, a priori analysis for air-filled Rayleigh-Bénard convection (RBC) clearly shows a strong misalignment. In the quest for more accurate models, we firstly study and confirm the suitability of the eddy-viscosity assumption for RBC carrying out a posteriori tests for different models at very low Prandtl numbers (liquid sodium, Pr=0.005) where no heat flux SGS activity is expected. Then, a new tensorial SGS heat flux model is proposed and studied a priori using DNS data of an air-filled (Pr=0.7) RBC at Rayleigh numbers up to 1011. Apart from having good alignment trends with the actual SGS heat flux, it is numerically stable per se and has the proper cubic nearwall behavior. Our near future research plans include testing a posteriori this new tensorial SGS heat flux model. Prior to that, we also aim to properly discretize these models in space and time., F.X.T., F.D. and A.O. have been supported by the Ministerio de Economía y Competitividad, Spain, ANUMESOL project (ENE2017-88697-R). F.X.T. and A.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722) and by the Clean Sky 2 Joint Undertaking, ANTIFOD project (grant ID 821352). F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). D.S. is supported by an FI AGAUR-Generalitat de Catalunya grant (2020FI B 00839). Calculations were performed on the MareNostrum 4 supercomputer at the BSC. The authors thankfully acknowledge these institutions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Three-dimensional direct numerical simulation (dns) Of taylor bubbles rising in non-Newtonian environments

  • Amani, Ahmad|||0000-0001-5197-2879
  • Castro González, Jesús|||0000-0002-8943-2402
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Three-dimensional numerical simulation of Taylor gas bubbles as primary unites of slug flow patterns rising in non-Newtonian environments is performed in the context of Direct Numerical Simulation (DNS) of the governing equations, where the whole physics of fluid motions will be taken into account. State-of-the-art numerical tools are proposed to tackle the numerical challenges in the DNS study of this problem. E.g. a coupled level-set volume-of-fluid (CLSVOF) interface capturing method is used to solve the topological changes of the interface. Physical formulations are integrated with moving-mesh (MM) technique to decrease the computational cost of 3D simulations and adaptivemesh-refinement (AMR) technique to increase the local accuracy around the interface. The governing equations are solved using High-Performance Computing (HPC) parallel approaches. To the best of the authors’ knowledge, this is the first work dealing with three-dimensional direct numerical simulation of Taylor bubbles rising in non-Newtonian environments.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Subgrid-Scale Model Based on the Invariants of the Gradient Model Tensor

  • Folch Flórez, David
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The incompressible Navier-Stokes equations stand as the best mathematical model for turbulent flows. However, direct numerical simulations at high Reynolds numbers are not yet feasible because the convective term produces far too many relevant scales of motion, thus remaining limited to relatively low-Reynolds numbers. Dynamically less complex mathematical formulations have been developed for coarse-grain simulations, like the well known eddy-viscosity models. Most of these models are based on the combination of invariants of a symmetric tensor that depends on the gradient of the resolved velocity field, G = Ñu, and should properly detect different flow configurations (laminar and 2D flows, near-wall behavior, transitional regime, etc.). Brand-new models have been constructed considering the first three invariants of the symmetric tensor GGT with excellent results;1 hence, it is formally based on the lowest-order approximation of the subgrid stress tensor, t(u) = D2 12GGT +O(D4), i.e. the gradient model proposed by Clark.2 Furthermore, these models have been implemented on a pseudo-spectral algorithm with a fully-explicit second-order time-integration method.3 The performance of this special configuration has been successfully tested for decaying isotropic turbulence and a turbulent channel flow. It is currently being developed for a semi-infinite boundary layer with periodic conditions as a previous step to carry out wind farm simulations. Details of the implementation and numerical results will be presented., The work has been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency. The authors thankfully acknowledge these institutions.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

An energy-preserving level set method for multiphase flows

  • Valle Marchante, Nicolás|||0000-0003-2140-041X
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Castro González, Jesús|||0000-0002-8943-2402
The computation of multiphase flows presents a subtle energetic equilibrium between potential (i.e., surface) and kinetic energies. The use of traditional interface-capturing schemes provides no control over such a dynamic balance. In the spirit of the well-known symmetry-preserving and mimetic schemes, whose physics-compatible discretizations rely upon preserving the underlying mathematical structures of the space, we identify the corresponding structure and propose a new discretization strategy for curvature. The new scheme ensures conservation of mechanical energy (i.e., surface plus kinetic) up to temporal integration. Inviscid numerical simulations are performed to show the robustness of such a method., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Building a proper tensor-diffusivity model for large-eddy simulation of buoyancy-driven flows

  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Dabbagh, Firas|||0000-0001-8440-507X
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
In this work, we plan to shed light on the following research question: can we ¿nd a nonlinear tensorial subgrid-scale (SGS) heat ¿ux model with good physical and numerical properties, such that we can obtain satisfactory predictions for buoyancy driven turbulent ¿ows? This is motivated by our recent ¿ndings showing that the classical (linear) eddy-di¿usivity assumption, qeddy ¿¿ T, fails to provide a reasonable approximation for the SGS heat ¿ux, q = uT - uT. This has been shown in our recent work [Dabbagh et al., Phys. Fluids 29, 105103 (2017)] where SGS features have been studied a priori for a Rayleigh-Bénard convection (RBC). We have also concluded that nonlinear (or tensorial) models can give good approximations of the actual SGS heat ¿ux. The nonlinear Leonard model, qnl ¿¿u¿T, is an example thereof. However, this model is unstable and therefore it cannot be used as standalone SGS heat ¿ux model. Apart from being numerically stable we also want to have the proper cubic near-wall behavior. Corrections in this regard will be presented together with a priori/posteriori studies of nonlinear SGS heat ¿ux models for RBC. Results from LES simulations will be compared with the DNS results obtained in the on-going PRACE project “Exploring new frontiers in Rayleigh-Bénard convection”., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On the Feasibility of CFD for Transient Air Flow Simulations in Buildings

  • Morozova, Nina
  • Capdevila Paramio, Roser|||0000-0003-2569-2544
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The rapidly growing computational capacity hasmade CFD simulations an attractive tool for indoorenvironmental applications. The ability of CFD toperform transient simulations could be incorporatedinto model predictive control systems for buildings inorder to correctly reproduce prompt disturbances inthe air field, such as opening doors and windows orchanges in occupants behaviour. In this work, twocharacteristic configurations which mimic typical air-flow patterns inside buildings are studied using dif-ferent grid sizes and turbulence models. Case one isa tall turbulent differentially heated cavity and casetwo is the turbulent mixed convection in a ventilatedsquare cavity. The Spearman’s rank correlation coef-ficient for transient simulations is compared againstcomputational time for different CFD approaches,and the possibility of performing real-time simula-tions is evaluated. Among different turbulence mod-els studied, the no-model approach with symmetrypreserving discretization has shown the best overallperformance in terms of computational cost and ac-curacy of the results., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A GPU Accelerated Framework for Partitioned Solution of Fluid-Structure Interaction Problems

  • Totounferoush, Amin
  • Naseri, Alireza|||0000-0002-8650-5434
  • Chiva Segura, Jorge|||0000-0001-5466-6869
  • Oliva Llena, Asensio|||0000-0002-2805-4794
  • Mehl, Miriam
We present a GPU-accelerated solver for the partitioned solution of fluid-structure interaction (FSI) problems. Independent scalable fluid and structure solvers are coupled by a library which handles the inter-code data communication, mapping and equation coupling. A coupling strategy is incorporated which allows accelerating expensive components of the coupled framework by offloading them to GPUs. To prove the efficiency of the proposed coupling strategy in conjunction with the offloading scheme, we present a numerical performance analysis for a complex test case in the filed of biomedical engineering. The numerical experiments demonstrate an excellent speed-up in the accelerated kernels (up to 133 times) which results in 6 to 8 times faster overall simulations. In addition, we observed a very good reduction in total simulation time by increasing the exploited compute nodes up to 8 (complete machine capacity)., We thank the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) for supporting this work by funding - EXC2075 – 390740016 under Germany’s Excellence Strategy. We acknowledge the support by the Stuttgart Center for Simulation Science (SimTech). This work was also financially supported by • priority program 1648 - Software for Exascale Computing 214 (ExaFSA - Exascale Simulation of Fluid-Structure-Acoustics Interactions) of the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation), • Ministerio de Economía y Competitividad, Secretaría de Estado de Investigacion, Desarrollo e ´ Innovacion, Spain (ENE2017-88697-R). ´ The performance measurements were carried out on the Vulcan cluster at the High-Performance Computing Center Stuttgart (HLRS). The authors wish to thank HLRS for compute time and technical support., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Comparison of Sliding Mesh and Immersed Boundary Methods in Unsteady Simulations

  • Vera i Fernández, Jordi|||0000-0002-7696-3802
  • Muela Castro, Jordi|||0000-0003-1583-8490
  • Favre, Federico
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
The feasibility and accuracy of two methods for simulating moving bodies inside a fluid are studied. Different cases are presented using the Immersed Boundary Method and the Sliding Mesh technique. The results obtained by both methods are compared and assessed. These results allow to study the accuracy of both methods as well as their computational feasibility, in terms of computation time, mesh requirements and parallel scalability.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

NUMA-Aware Strategies for the Heterogeneous Execution of SPMV on Modern Supercomputers

  • Álvarez Farré, Xavier|||0000-0002-1684-7658
  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The sparse matrix-vector product is a widespread operation amongst the scientific computing community. It represents the dominant computational cost in many large-scale simulations relying on iterative methods, and its performance is sensitive to the sparse pattern, the storage format, and kernel implementation, and the target computing architecture. In this work, we are devoted to the efficient execution of the sparse matrix-vector product on (potentially hybrid) modern supercomputers with non-uniform memory access configurations. A hierarchical parallel implementation is proposed to minimize the number of processes participating in distributed-memory parallelization. As a result, a single process per computing node is enough to engage all its hardware and ensure efficient memory access on manycore platforms. The benefits of this approach have been demonstrated on up to 9,600 cores of MareNostrum 4 supercomputer, at Barcelona Supercomputing Center., The work of A. Gorobets has been funded by the Russian Science Foundation, project 19- 11-00299. The work of X. Alvarez-Farr ´ e, F. X. Trias and A. Oliva has been financially supported ´ by the ANUMESOL project (ENE2017-88697-R) by the Spanish Research Agency (Ministerio de Economía y Competitividad, Secretaría de Estado de Investigacion, Desarrollo e Inno- ´ vacion), and the FusionCAT project (001-P-001722) by the Government of Catalonia (RIS3CAT ´ FEDER). The studies of this work have been carried out using the MareNostrum 4 supercomputer of the Barcelona Supercomputing Center (projects IM-2020-2-0029 and IM-2020-3-0030); the TSUBAME3.0 supercomputer of the Global Scientific Information and Computing Center at Tokyo Institute of Technology; the Lomonosov-2 supercomputer of the shared research facilities of HPC computing resources at Lomonosov Moscow State University; the K-60 hybrid cluster of the collective use center of the Keldysh Institute of Applied Mathematics. The authors thankfully acknowledge these institutions for the compute time and technical support.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A highly portable heterogeneous implementation of a Poisson solver for flows with one periodic direction

  • Alsalti Baldellou, Àdel|||0000-0002-5331-4236
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Álvarez Farré, Xavier|||0000-0002-1684-7658
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The portability of codes has become a major advantage given the continuous development of new architectures for numerical applications, as well as the progressive incorporation of accelerators in modern supercomputers. Following this trend, we have adopted an algebraic approach in the implementation of a Poisson solver for incompressible flows with one periodic direction. This approach, which basically consists of adapting a reduced set of fundamental operations to any architecture (such as the sparse matrixvector product or the dot product of two vectors), allows us to efficiently port our applications to any heterogeneous supercomputers in an easy manner. More particularly, our three-dimensional solver takes advantage of the existing periodic dimension (by means of a Fourier decomposition) to later execute overlapped data transpositions among devices, which conveniently share the workload with their CPU hosts, and solve the resulting two-dimensional decoupled subsystems., The work has been financially supported by a competitive R+D project (ENE2017- 88697-R) by the Spanish Research Agency. A.A.B is supported by a predoctoral contract (DIN2018-010061) by the Ministry of Science, Innovation and Universities of Spain (MICINN) and X.A.F. by the by the Government of Catalonia (2019FI_B2-00076).
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Paving the (right) way for DNS and LES on unstructured grids: (fully) conservative collocated/staggered discretizations

  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The essence of turbulence are the smallest scales of motion. They result from a subtle balance between convective transport and diffusive dissipation. Mathematically, these terms are governed by two differential operators differing in symmetry: the convective operator is skew-symmetric whereas the diffusive is symmetric and positive-definite. On the other hand, accuracy and stability need to be reconciled for simulations of turbulent flows in complex geometries. With this in mind, a fully-conservative discretization method for general unstructured grids was proposed in Ref. [1]: it exactly preserves the symmetries of the underlying differential operators on collocated grids. Hence, unlike other formulations, the discrete convective operator transports energy from a resolved scale of motion to other resolved scales without dissipating energy, as it should do from a physical point-of-view. Therefore, we think that apart from being a right approach for large-scale DNSs of turbulence, it also forms a solid basis for testing subgrid scale LES models. In this work, we will explore the possibility to build up staggered formulations based on the set of discrete operators defined for collocated meshes., F.X.T. and A.O. are financially supported by the Ministerio de Economía y Competitividad, Spain (ENE2017-88697-R). F.X.T. was supported by a Ramón y Cajal contract (RYC-2012-11996). Simulations were carried out on the MareNostrum 4 supercomputer at the BSC. The authors thankfully acknowledge these institutions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

An efficient Two-Layer wall model for accurate numerical simulations of aeronautical applications

  • Calafell Sandiumenge, Joan|||0000-0002-2333-7314
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Two-Layer wall models have been widely studied since they allow wall modeled Large Eddy Simulationsof general non-equilibrium flows. However, they are plagued by two persistent problems, the "log-layermismatch" and the resolved Reynolds stresses inflow. Several methodologies have been proposed so far todeal with these problems separately. In this work, a time-filtering methodology is used to tackle both issuesat once with a single and low-computational-cost step, easily applicable to complex three-dimensionalgeometries. Additionally, it is shown that the techniques intended to suppress the Reynolds stresses inflowproposed so far, were not sufficient to completely mitigate their detrimental effects., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Assessment and comparison of a recent kinematic sensitive subgrid length scale in Hybrid RANS-LES

  • Pont Vilchez, Arnau|||0000-0001-9068-3076
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Revell, Alistair
  • Oliva Llena, Asensio|||0000-0002-2805-4794
A recent kinematic sensitive subgrid length scale, Δlsq, initially developed for LES applications, is now considered for DES. Even though it is presented as a subgrid length scale, instead of a grey area mitigation (GAM) technique, this initial study shows how it could also be a good and natural approach for addressing this well-known DES shortcoming. In this paper, the Δlsq has been compared with a well-known kinematic sensitive length scale, Δ~ω. It includes a mesh resilience and a shear layer delay study with a Decaying Homogeneous Isotropic Turbulence configuration and two Backward Facing Step configurations, respectively. Encouraging results have been obtained, indicating Δlsq as a subgrid length scale to be considered., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Towards Real-Time CFD Simulation of Indoor Environment

  • Morozova, Nina
  • Capdevila Paramio, Roser|||0000-0003-2569-2544
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Growing computational power and improved numerical algorithms make Computational Fluid Dynamics (CFD) an attractive tool for simulations of indoor environment. In this study di¿erent turbulent models and discretization approaches are investigated on set of di¿erent mesh resolutions in order to choose the CFD technique that suits best for indoor environmental simulations. The investigated con¿guration is the tall deferentially-heated cavity with height aspect ratio of 3.84, this con¿guration resembles a strati¿ed indoor environment, such as a building atrium. The relative error of global air¿ow quantities is compared against computational time for di¿erent CFD approaches. LES simulations together with staggered discretization show the best overall performance in terms of computational speed and accuracy ratio. Furthermore the capability of CFD to perform real-time and even faster than real-time simulations is studied in paradigm of applying it for indoor environmental design and control systems., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

An enhanced finite volume based solver for thermoelastic materials in fluid-structure coupled problems

  • González Acedo, Ignacio|||0000-0001-5679-1073
  • Naseri, Alireza|||0000-0002-8650-5434
  • Chiva Segura, Jorge|||0000-0001-5466-6869
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Computational investigation of the hexagonal honeycomb adsorption reactor for cooling applications: Honeycomb adsorption reactor for cooling

  • Papakokkinos, Giorgos
  • Castro González, Jesús|||0000-0002-8943-2402
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Adsorption cooling is a sustainable technology, since it can utilize solar energy or waste heat, while employing substances without ozone depletion and global warming potential. The adsorption reactor design is determinant for the system performance. An underexplored geometry hitherto – the hexagonal honeycomb adsorption reactor – was numerically investigated. An in-house, validated, three-dimensional computational model based on unstructured meshes was employed. The Specific Cooling Power (SCP) and Coefficient of Performance (COP) were quantified for several geometrical and operational parameters. The cell inradius creates a dichotomy between SCP and COP, being 218.9 W/kg¿s and 0.356 for 1 mm, while being 80.4 W/kg¿s and 0.606 for 6 mm. The cell height influences prominently the SCP, being 159.5 W/kg¿s and 86.1 W/kg¿s for 5 mm and 30 mm, respectively. The fin thickness impacts mostly the COP, being 0.599 and 0.364 for 0.5 mm and 3 mm, respectively. Higher COP is achieved for higher evaporator, lower adsorption and lower condenser temperatures. Higher SCP is achieved for lower adsorption and condenser, and higher evaporator and desorption temperatures. Shorter cycles result in high SCP and low COP, whereas the inverse occurs for longer cycles. Aluminum heat exchanger yields 7.7% higher COP than copper. The results are discussed from a physical, as well as, an engineering perspective., This study was financially supported by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO, ENE2017-88697R). Carles Oliet, as a Serra Hunter lecturer, acknowledges the Catalan Government for the support through this programme., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Symmetry-preserving discretization of Navier-Stokes on unstructured grids: collocated vs staggered

  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Valle Marchante, Nicolás|||0000-0003-2140-041X
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The essence of turbulence are the smallest scales of motion. They result from a subtle balance between convective transport and diffusive dissipation. Mathematically, these terms are governed by two differential operators differing in symmetry: the convective operator is skew-symmetric, whereas the diffusive is symmetric and positive-definite. On the other hand, accuracy and stability need to be reconciled for numerical simulations of turbulent flows around complex configurations. With this in mind, a fully-conservative discretization method for general unstructured grids was proposed [Trias et al., J.Comp.Phys. 258, 246-267, 2014]: it exactly preserves the symmetries of the underlying differential operators on a collocated mesh. However, any pressure-correction method on collocated grids suffer from the same drawbacks: the cell-centered velocity field is not exactly incompressible and some artificial dissipation is inevitable introduced. On the other hand, for staggered velocity fields, the projection onto a divergence-free space is a well-posed problem: given a velocity field, it can be uniquely decomposed into a solenoidal vector and the gradient of a scalar (pressure) field. This can be easily done without introducing any dissipation as it should be from a physical point-of-view. In this work, we explore the possibility to build up staggered formulations based on collocated discrete operators., F.X.T., N.V. and A.O. have been financially supported by the Ministerio de Economía y Competitividad, Spain, ANUMESOL project (ENE2017-88697-R). F.X.T. and A.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722). N.V. was supported by an FI AGAUR-Generalitat de Catalunya fellowship (2017FI B 00616). Calculations were performed on the IBM MareNostrum 4 supercomputer at the BSC. The authors thankfully acknowledge these institutions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On a Proper Tensor-Diffusivity Model for Large-Eddy Simulation of Buoyancy-Driven Turbulence

  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Dabbagh, Firas|||0000-0001-8440-507X
  • Gorobets, Andrei
  • Oliet Casasayas, Carles|||0000-0003-2170-5299
In this work, we aim to shed light to the following research question: can we find a nonlinear tensorial subgrid-scale (SGS) heat flux model with good physical and numerical properties, such that we can obtain satisfactory predic- tions for buoyancy-driven turbulent flows? This is motivated by our findings showing that the classical (linear) eddy-diffusivity assumption, qeddy ¿ ¿T, fails to provide a reasonable approximation for the actual SGS heat flux, q = uT - uT: namely, a priori analysis for air-filled Rayleigh-Bénard convection (RBC) clearly shows a strong misalignment. In the quest for more accurate models, we firstly study and confirm the suitability of the eddy-viscosity assumption for RBC carrying out a posteriori tests for different models at very low Prandtl numbers (liquid sodium, Pr = 0.005) where no heat flux SGS activity is expected. Then, different (nonlinear) tensor-diffusivity SGS heat flux models are studied a priori using DNS data of air-filled (Pr = 0.7) RBC at Rayleigh numbers up to 1011. Apart from having good alignment trends with the actual SGS heat flux, we also restrict ourselves to models that are numerically stable per se and have the proper cubic near-wall behavior. This analysis leads to a new family of SGS heat flux models based on the symmetric positive semi-definite tensor GGT where G = ¿u, i.e. q ¿ GGT¿T, and the invariants of the GGT tensor, F.X.T. and F.D. are supported by the Ministerio de Economía y Competitividad, Spain (ENE2017-88697-R). F.X.T. and C.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722). F.X.T. was financially supported by a Ramón y Cajal post-doctoral contract (RYC-2012-11996). F.X.T. and A.G. are supported by the Research project 20-02-01 of the Department of the Moscow Center for Fundamental and Applied Mathematics at the Keldysh Insti-tute of Applied Mathematics of RAS. F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). Calculations have been performed on the MareNostrum 4 supercomputer at the BSC (PRACE 15th Call, Ref. 2016163972, “Exploring new fron-tiers in Rayleigh-Bénard convection”; and RES project FI-2019-1-0040 “Exploring nonlinear subgrid-scale heat flux models for buoyancy driven flows”). Preliminary simulations were carried out using computational resources of MCC NRC “Kurchatov Institute”, http://compu ting.nrcki .ru/. The authors thankfully acknowl-edge these institutions, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Symmetry-Preserving Discretizations In Unstructured Staggered Meshes

  • Valle Marchante, Nicolás|||0000-0003-2140-041X
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Verstappen, R.W.C.P.
The adoption of symmetry-preserving discretizations is presented in terms of the collocated, unstructured meshes customary of commercial codes. By adopting an algebraic approach, a discretization of the convective terms that reduces to the well know staggered method of Harlow and Welch is presented. The scheme properties are presented along with benchmark simulations concerning turbulent flows, achieving exact conservation of momentum and kinetic energy., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Data-driven prediction of flow parameters in a ventilated cavity using high-fidelity CFD simulations

  • Morozova, Nina
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Capdevila Paramio, Roser|||0000-0003-2569-2544
  • Oliva Llena, Asensio|||0000-0002-2805-4794
In this study, we develop a machine-learning-based data-driven model, which predicts comfort-related flow parameters in a ventilated room. The model is based on the results of high-fidelity computational fluid dynamics (CFD) simulations with different geometrical configurations and boundary conditions. The developed model could be used as a cheaper alternative to CFD for applications where rapid predictions of complex flow configurations are required, such as model predictive control. Even though the developed model provides acceptable accuracy for most of the tested configurations, more input data is required to improve the model performance., This work is supported by the Ministerio de Economía y Competitividad, Spain [ENE2017-88697-R]. N. Morozova is supported by the by the Ministerio de Economía y Competitividad, Spain [FPU16/06333 predoctoral contract]. Part of the calculations was performed on the MareNostrum 4 supercomputer at the Barcelona Supercomputing Center [RES project IM-2021-1-0015]., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Simulation of fluid-structure interaction and impact force on a reed valve

  • Castrillo Green, Pablo|||0000-0002-1253-745X
  • Schillaci, Eugenio|||0000-0002-6690-6871
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
The cyclic impact force between a reed valve and the seat plate is the main reason of the valve failure in many thermo-technical devices as compressors, engines, etc. According to experimental observations the latter is due to fatigue and usually occurs in the leading part of the valve ‘neck’. In this work, a complex numerical analysis is presented aimed to studying the external forces and internal stresses suffered by the valve. In particular, the impact force between the valve and the seat is studied. The numerical analysis relies on the coupled synergy of two different simulation concepts. In order to do so, two codes are used: (1) first, the in-house Computational Fluid Dynamics (CFD) code presented in [1] is employed to simulate the Fluid-Structure Interaction (FSI) between gas and valve, extracting reference data for valve displacement and external gas pressures; (2) second, the analysis of the internal structure stresses, together with the impact forces with the plate is implemented in a Computational Solid Dynamics (CSD) code developed in FreeFEM++ [2]. The impact force representation is based on the formulation presented in [3] where a conserving algorithm for frictionless dynamic contact/impact is developed. Due to the importance of obtaining an adequate impact force, an exhaustive study is carried out on its characterization in terms of numerical parameters, such as the penalty stiffness. Under this framework, the valve displacement and impact velocities are verified. Hence, impact forces are analysed in different scenarios, obtaining interesting observations about stresses distribution, with a particular focus on the points where failure is experienced., The authors acknowledge Voestalpine Precision Strip AB company for the previous research collaboration project that allowed to validate experimentally the presented numerical methods. P. Castrillo gratefully acknowledges the Universitat Politecnica de Catalunya and Banco Santander for the financial ` support of his predoctoral grant FPI-UPC (109 FPI-UPC 2018). E. Schillaci acknowledges the financial support of the Programa Torres Quevedo (PTQ2018-010060). This work has also been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical Analysis of Viscoelastic Fluid Injection Processes

  • Amani, Ahmad|||0000-0001-5197-2879
  • Schillaci, Eugenio|||0000-0002-6690-6871
  • Kizildag, Deniz|||0000-0002-2511-1992
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
In this work, a numerical framework aimed at simulating high-viscous and viscoelastic liquid injection processes is presented. The study of fluid injection with viscoelastic properties, such as synthetic polymers, is of great importance in several industrial sectors, such as metallurgy, automotive, food and pharmaceutical products, ink jets and 3D printers. In this work, a Geometrical Volume-of-Fluid (VOF) method is used to represent the interface, while finite-volume discretizations of Navier-Stokes equations on collocated unstructured meshes are solved through a fractional step method. Viscoelastic constitutive models are used to resolve the non-Newtonian behaviours. The employed implementations allow integrating different types of constitutive equations and stabilization approaches. The test case proposed in the current work consist of the simulation of the discharge of a polymeric jet from an upper nozzle into an air-containing cavity with solid bottom. The behavior of the fluids under analysis is validated by observing the onset of fluid-buckling s tructures. This phenomenon consists in the appearance of toroidal oscillation (as coiling and folding patterns) after the jet hits the solid surface and begins to accumulate. First, low-Reynolds number (Re<1.0) Newtonian Jets are analyzed, with the objective of validating the appearance of buckling as a function of Re number, and comparing the results with reference works. Finally, the potentialities of the proposed numerical methods are shown by simulating buckling phenomena in viscoelastic Jets described with the Oldroyd-B constitutive model., This work was developed in the context of a research project (BASE3D 001-P-001646) co-financed by the European Union Regional Development Fund within the framework of the ERDF Operational Program of Catalonia 2014-2020 with a grant of 50% of total cost eligible. The work has also been financially supported by a competitive R+D project (ENE2017-88697-R) of the Spanish Research Agency. The author E.Schillaci acknowledges the financial support of the Programa Torres Quevedo (PTQ2018- 010060).
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Unstructured Level-Set Method For Saturated Liquid-Vapor Phase Change

  • Balcázar Arciniega, Néstor|||0000-0003-0776-2086
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Oliva Llena, Asensio|||0000-0002-2805-4794
A novel conservative level-set method for saturated liquid-vapor phase change on unstruc-tured meshes is introduced. Transport equations are discretized by the finite-volume method on col-located unstructured grids. Mass transfer promoted by thermal phase change is computed using theenergy jump condition at the interface, as a function of the temperature gradient. The fractional-stepprojection method is used for solving the pressure-velocity coupling, convective terms are discretized byunstructured flux-limiter schemes, central difference scheme is used for discretization of diffusive terms.Verification and validation cases have been undertaken to prove the accuracy and robustness of the nu-merical methods, including simulation of the Stefan problem, and film boiling on a cylindrical surface.Excellent agreement between numerical solutions against analytical solution and empirical correlationsfrom the literature is reported., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

An efficient two-layer wall model for high Reynolds number large eddy simulation

  • Calafell Sandiumenge, Joan|||0000-0002-2333-7314
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Wall-bounded flows at high Reynolds number are an important research field given that they are present in many important industrial applications. Nonetheless, the use of accurate numerical methodologies such as Large Eddy Simulation (LES) for routine industrial applications, is still unfeasible due to their heavy computational cost. Wall-Modeled LES is intended to circumvent the massive costs of accurately resolving the boundary layer while benefiting from the temporal and spatial resolution of an LES computation. In this work, a Two-Layer Wall Model with a general formulation suitable for non-equilibrium flows and complex geometries is presented. The Two-Layer Models (TLM) suffer from two recurrent problems, the ”log-layer mismatch” (LLM) and the resolved Reynolds stresses inflow (RRSI). Until now, complex and expensive techniques have been proposed to overcome these problems separately. In the present work, a timeaveraging filter (TAF) is considered to deal with both issues at once, with a single and low-computational-cost technique. It is the first time that the TAF technique is used to block the RRSI. In this regard, a numerical experiment is initially performed to assess the TAF ability in doing so. Afterward, the WM is tested in regular operating conditions with a Ret ˜ 3000 pipe flow case. Good results are obtained in all the performed tests, showing the capability of the TAF of suppressing the LLM while avoiding the RRSI at the same time. This makes the new TLM methodology a very effcient technique compared to other implementations proposed so far., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On the Interpolation Problem for the Poisson Equation on Collocated Meshes

  • Santos Serrano, Daniel|||0000-0002-9179-4701
  • Muela Castro, Jordi|||0000-0003-1583-8490
  • Valle Marchante, Nicolás|||0000-0003-2140-041X
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
The appearence of unphysical velocities in highly distorted meshes is a common problem in many simulations. In collocated meshes, this problem arises from the interpolation of the pressure gradient from faces to cells. Using an algebraic form for the classical incompressible Navier-Stokes equations, this problem is adressed. Starting from the work of F. X. Trias et. al. [FX.Trias et al. JCP 258: 246-267, 2014], a new approach for studying the Poisson equation obtained using the Fractional Step Method is found, such as a new interpolator is proposed in order to found a stable solution, which avoid the appearence of these unpleasant velocities. The stability provided by the interpolator is formally proved for cartesian meshes and its rotations, using fully-explicit time discretizations. The construction of the Poisson equation is supported on mimicking the symmetry properties of the differential operators and the Fractional Step Method. Then it is reinterpreted using a recursive application of the Fractional Step Method in order to study the system as an stationary iterative solver. Furthermore, a numerical analysis for unstructured mesh is also provided., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (project ref. ENE2017-88697-R). D. Santos acknowledges a FI AGAUR-Generalitat de Catalunya fellowship (2020FI B 00839), and N. Valle also acknowledges a FI AGAUR-Generalitat de Catalunya fellowship (2017FI B 00616). The authors thankfully acknowledge these institutions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Energy preserving multiphase flows: applications to falling films

  • Valle Marchante, Nicolás|||0000-0003-2140-041X
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Castro González, Jesús|||0000-0002-8943-2402
The numerical simulation of multiphase flows presents several challenges, namely the transport of different phases within de domain and the inclusion of capillary effects. Here, these are approached by enforcing a discrete physics-compatible solution. Extending our previous work on the discretization of surface tension [N. Valle, F. X. Trias, and J. Castro, 'An energy-preserving level set method for multiphase flows,' J. Comput. Phys., vol. 400, p. 108991, 2020] with a consistent mass and momentum transfer a fully energy-preserving multiphase flow method is presented. This numerical technique is showcased within the simulation of a falling film under several working conditions related to the normal operation of LiBr absorption chillers., The authors acknowledge the computing resources provided by the Barcelona Supercomputing Center under contracts IM-2019-3-0026 and IM-2020-1-0006. An also grants from the Ministerio de Economía y Competitividad, Spain under contracts ENE2015-70672-P and ENE2017-88697-R. N. Valle also acknowledges an FI AGAUR-Generalitat de Catalunya fellowship under contract 2017FI B 00616, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Advanced techniques for grau area mitigation in DES simulations and their effectes on the subsonic round jet acoustic spectra, Tècniques avançades per la mitigació de la zona grisa en simulacions DES i els seus efectes en l'espectre acústic del jet circular

  • Duben, Alexey
  • Ruano Pérez, Jesús|||0000-0002-5121-2543
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
The research dedicated to the investigation of different gray-area mitigation approaches towards accurate aerodynamics and aeroacoustics is presented. The recent modifications of hybrid RANS-LES DDES approach based on combinations of new adapting subgrid length scales (~ !, SLA and lsq) and LES models ( and S3QR) are considered. The object of investigation is an immersed subsonic turbulent jet. The simulations are carried out on a set of refining meshes using two different scale-resolving numerical algorithms realized in the compressible codes NOISEtte and OpenFOAM. The evaluation of different approaches is focused on the analysis of far field noise. The results show that all the considered techniques provide appropriate accuracy to predict the noise generated by the turbulent jet. The study clearly demonstrated the importance of both numerical scheme and subgrid turbulence model. The peculiarities of considered approaches are revealed and discussed., A.D. was supported by Moscow Center for Fundamental and Applied Mathematics, Agreement with the Ministry of Science and Higher Education of the Russian Federation, No. 075-15-2019-1623. The NOISEtte computations were carried out using the equipment of the shared research facilities of HPC computing resources at Lomonosov Moscow State University and the computing resources of the federal collective usage center Complex for Simulation and Data Processing for Mega-science Facilities at NRC ”Kurchatov Institute” (http://ckp.nrcki.ru/). J.Ru. was supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain. J.Ru. and F.X.T. have been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.Ru., F.X.T. and J.Ri. are also supported by the Clean Sky 2 Joint Undertaking. ANTIFOD project (Grant ID 821352)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A hierarchical parallel implementation for heterogeneous computing. Application to algebra-based CFD simulations on hybrid supercomputers

  • Álvarez Farré, Xavier|||0000-0002-1684-7658
  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
The quest for new portable implementations of simulation algorithms is motivated by the increasing variety of computing architectures. Moreover, the hybridization of high-performance computing systems imposes additional constraints, since heterogeneous computations are needed to efficiently engage processors and massively-parallel accelerators. This, in turn, involves different parallel paradigms and computing frameworks and requires complex data exchanges between computing units. Typically, simulation codes rely on sophisticated data structures and computing subroutines, so-called kernels, which makes portability terribly cumbersome. Thus, a natural way to achieve portability is to dramatically reduce the complexity of both data structures and computing kernels. In our algebra-based approach, the scale-resolving simulation of incompressible turbulent flows on unstructured meshes relies on three fundamental kernels: the sparse matrix-vector product, the linear combination of vectors and the dot product. It is noteworthy that this approach is not limited to a particular kind of numerical method or a set of governing equations. In our code, an auto-balanced multilevel partitioning distributes workload among computing devices of various architectures. The overlap of computations and multistage communications efficiently hides the data exchanges overhead in large-scale supercomputer simulations. In addition to computing on accelerators, special attention is paid at efficiency on manycore processors in multiprocessor nodes with significant non-uniform memory access factor. Parallel efficiency and performance are studied in detail for different execution modes on various supercomputers using up to 9,600 processor cores and up to 256 graphics processor units. The heterogeneous implementation model described in this work is a general-purpose approach that is well suited for various subroutines in numerical simulation codes., The work of A. G. has been funded by the Russian Sci- ence Foundation, project 19-11-00299. The work of X. Á. F. and F. X. T. has been financially supported by the ANUMESOL project (ENE2017-88697-R) by the Spanish Research Agency, and the FusionCAT project (0 01-P-0 01722) by the Government of Catalo- nia RIS3CAT FEDER. X. Á. F. is supported by a predoctoral contract (2019FI_B2-0 0 076) by the Government of Catalonia. The work has been carried out using the MareNostrum 4 supercomputer of the Barcelona Supercomputing Center; the TSUBAME3.0 supercom-puter of the Global Scientific Information and Computing Center at Tokyo Institute of Technology; the Lomonosov-2 supercomputer of the shared research facilities of HPC computing resources at Lomonosov Moscow State University; the K-60 hybrid cluster of the Collective Usage Centre of KIAM RAS. The authors thankfully acknowledge these institutions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the feasibility of affordable high-fidelity CFD simulations for indoor environment design and control

  • Morozova, Nina
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Capdevila Paramio, Roser|||0000-0003-2569-2544
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
  • Oliva Llena, Asensio|||0000-0002-2805-4794
Computational fluid dynamics (CFD) is a reliable tool for indoor environmental applications. However, accurate CFD simulations require large computational resources, whereas significant cost reduction can lead to unreliable results. The high cost prevents CFD from becoming the primary tool for indoor environmental simulations. Nonetheless, the growth in computational power and advances in numerical algorithms provide an opportunity to use accurate and yet affordable CFD. The objective of this study is to analyze the feasibility of fast, affordable, and high-fidelity CFD simulations for indoor environment design and control using ordinary office computers. We analyze two representative test cases, which imitate common indoor airflow configurations, on a wide range of different turbulence models and discretizations methods, to meet the requirements for the computational cost, run-time, and accuracy. We consider statistically steady-state simulations for indoor environment design and transient simulations for control. Among studied turbulence models, the no-model and large-eddy simulation with staggered discretizations show the best performance. We conclude that high-fidelity CFD simulations on office computers are too slow to be used as a primary tool for indoor environment design and control. Taking into account different laws of computer growth prediction, we estimate the feasibility of high-fidelity CFD on office computers for these applications for the next decades, This work is supported by the Ministerio de Economía y Competitividad, Spain [ENE2017-88697-R]. N. Morozova is supported by the by the Ministerio de Economía y Competitividad, Spain [FPU16/06333 predoctoral contract]. Part of the calculations was performed on the MareNostrum 4 supercomputer at the Barcelona Supercomputing Center [RES project I-2019-2-0021]. The authors thankfully acknowledge these institutions. The authors would also like to thank our colleague MSc Xavier Álvarez Farré for the productive discussions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Flow topology dynamics in a three-dimensional phase space for turbulent Rayleigh-Bénard convection

  • Dabbagh, Firas|||0000-0001-8440-507X
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
F.X.T., F.D. and A.O. are financially supported by the Ministerio de Economía y Competitividad, Spain (ENE2017-88697-R). F.X.T. is supported by a Ramón y Cajal postdoctoral contract (RYC-2012-11996). F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). Calculations have been performed on the IBM MareNostrum 4 supercomputer at the BSC (PRACE 15th Call, Ref. 2016163972, \Exploring new frontiers in Rayleigh-Bénard convection"). Preliminary simulations were carried out using computational resources of MCC NRC \Kurchatov Institute", http://computing.nrcki.ru/. The authors thankfully acknowledge these institutions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

On Preconditioning Variable Poisson Equation with Extreme Contrasts in the Coefficients

  • Alsalti Baldellou, Àdel|||0000-0002-5331-4236
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
  • Gorobets, Andrei
  • Oliva Llena, Asensio|||0000-0002-2805-4794
It is well known that the solution by means of iterative methods of very ill-conditioned systems leads to very poor convergence rates. In this context, preconditioning becomes crucial in order to modify the spectrum of the system being solved and improve the performance of the solvers. A proper balance between the reduction in the number of iterations and the overhead of the construction and application of the preconditioner needs to be sought to actually decrease the total execution time of the solvers. This is particularly important when considering variable coefficients matrices as, in general, its preconditioners will also be variable and need to be updated regularly at an affordable cost. In this work we present a family of variable preconditioners designed for the effective solution of variable Poisson equation with extreme contrasts in the coefficients, which represents a particularly challenging case as it translates into a variable and extremely ill-conditioned system arising in many situations such as with multiphase flows presenting high density ratios or in the presence of highly-stretched adaptive mesh refinements. Finally, the results of the numerical experiments performed are presented and discussed, confirming our preconditioners as extremely affordable, highly-parallelizable and easy-to-implement alternatives to the more standard (and usually unfeasible) preconditioners, still showing great improvements in the rate of convergence of the solvers without requiring the variable coefficients matrix to be explicitly rebuilt at each iteration., Àdel Alsalti-Baldellou, F. Xavier Trias and Assensi Oliva have been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency. Àdel Alsalti-Baldellou is also supported by predoctoral grants DIN2018-010061 and 2019-DI-90, given by, respectively, the Spanish Ministry of Science, Innovation and Universities (MICINN) and the Catalan Agency for Management of University and Research Grants (AGAUR).
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Detailed prediction of fluid-solid coupled phenomena of turbulent flow through reed valves

  • González Acedo, Ignacio|||0000-0001-5679-1073
  • Naseri, Alireza|||0000-0002-8650-5434
  • Rigola Serrano, Joaquim|||0000-0002-6685-3677
  • Pérez Segarra, Carlos David|||0000-0003-1007-3142
  • Oliva Llena, Asensio|||0000-0002-2805-4794
The operation of self-actuated valves in suction and discharge processes plays a crucial role in the thermal efficiency and structural reliability of hermetic reciprocating compressors. The present work provides a thorough description of an in-house numerical method based on a partitioned fluid-structure interaction algorithm intended to obtain high-fidelity numerical predictions and optimise valve system design. A large eddy simulation model is used for the turbulent flow, whereas a normal mode superposition assumption along with an impact penalty method is used for the reed. Under this framework, a detailed analysis of the coupled problem with a straight and tapered exit ports is carried out. Differences in effective flow area and pressure drop are found as a result of the port geometry, but also of the valve velocity, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

New Strategies for Mitigating the Gray Area in Delayed-Detached Eddy Simulation Models

  • Pont Vilchez, Arnau|||0000-0001-9068-3076
  • Duben, Alexey
  • Gorobets, Andrei
  • Revell, Alistair
  • Oliva Llena, Asensio|||0000-0002-2805-4794
  • Trias Miquel, Francesc Xavier|||0000-0002-5966-0703
This paper presents a new approach for mitigating the unphysical delay in the Reynolds-averaged Navier–Stokes (RANS) to large-eddy simulation (LES) transition, often referred to as the gray area, which is a common issue for hybrid RANS–LES turbulence models such as delayed-detached eddy simulation. An existing methodology designed for improving the LES performance in complex flows is adapted and tested. This is based on reducing the numerical diffusion in critical areas for permitting a more accurate development of turbulence. The new formulation comprises both a two-dimensional sensitive velocity gradient model and an alternative definition of the subgrid length scale, which are tested both individually and in tandem, and compared with the other formulations commonly used for addressing the gray area. Four test cases are examined, a flat plate, two variants of the incompressible backwardfacing step, and an open jet compressible case, all of which are selected to expose the adverse impact of numerical diffusion that this study seeks to address. Furthermore, the proposed changes are implemented in two different codes for the purpose of cross-validation. Encouraging results are observed, supporting the suitability of the new approach as a candidate for addressing the gray area issue in flows of this kind., This work was financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). A.P.V. was supported by an FI-DGR 2016 predoctoral contract (No. 2018FI_ B2_00072) financed by Generalitat de Catalunya, Spain. F.X.T. was supported by a Ramón y Cajal postdoctoral contract (No. RYC-2012- 11996) financed by the Ministerio de Economía y Competitividad, Spain. A.D. and A.G. were supported by Moscow Center for Fundamental and Applied Mathematics, Agreement with the Ministry of Science and Higher Education of the Russian Federation, No. 075- 15-2019-1623. The NOISEtte computations were carried out using the equipment of the shared research facilities of HPC computing resources at Lomonosov Moscow State University and the computing resources of the federal collective usage center Complex for Simulation and Data Processing for Mega-science Facilities at NRC “Kurchatov Institute” (http://ckp.nrcki.ru/)., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Computational investigation of the hexagonal honeycomb adsorption reactor for cooling applications: Honeycomb adsorption reactor for cooling

  • Papakokkinos, Giorgos
  • Castro González, Jesús
  • Oliet Casasayas, Carles
  • Oliva Llena, Asensio
Adsorption cooling is a sustainable technology, since it can utilize solar energy or waste heat, while employing substances without ozone depletion and global warming potential. The adsorption reactor design is determinant for the system performance. An underexplored geometry hitherto – the hexagonal honeycomb adsorption reactor – was numerically investigated. An in-house, validated, three-dimensional computational model based on unstructured meshes was employed. The Specific Cooling Power (SCP) and Coefficient of Performance (COP) were quantified for several geometrical and operational parameters. The cell inradius creates a dichotomy between SCP and COP, being 218.9 W/kg¿s and 0.356 for 1 mm, while being 80.4 W/kg¿s and 0.606 for 6 mm. The cell height influences prominently the SCP, being 159.5 W/kg¿s and 86.1 W/kg¿s for 5 mm and 30 mm, respectively. The fin thickness impacts mostly the COP, being 0.599 and 0.364 for 0.5 mm and 3 mm, respectively. Higher COP is achieved for higher evaporator, lower adsorption and lower condenser temperatures. Higher SCP is achieved for lower adsorption and condenser, and higher evaporator and desorption temperatures. Shorter cycles result in high SCP and low COP, whereas the inverse occurs for longer cycles. Aluminum heat exchanger yields 7.7% higher COP than copper. The results are discussed from a physical, as well as, an engineering perspective., This study was financially supported by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO, ENE2017-88697R). Carles Oliet, as a Serra Hunter lecturer, acknowledges the Catalan Government for the support through this programme., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

An efficient Two-Layer wall model for accurate numerical simulations of aeronautical applications

  • Calafell Sandiumenge, Joan
  • Trias Miquel, Francesc Xavier
  • Oliva Llena, Asensio
Two-Layer wall models have been widely studied since they allow wall modeled Large Eddy Simulationsof general non-equilibrium flows. However, they are plagued by two persistent problems, the "log-layermismatch" and the resolved Reynolds stresses inflow. Several methodologies have been proposed so far todeal with these problems separately. In this work, a time-filtering methodology is used to tackle both issuesat once with a single and low-computational-cost step, easily applicable to complex three-dimensionalgeometries. Additionally, it is shown that the techniques intended to suppress the Reynolds stresses inflowproposed so far, were not sufficient to completely mitigate their detrimental effects., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Data-driven prediction of flow parameters in a ventilated cavity using high-fidelity CFD simulations

  • Morozova, Nina
  • Trias Miquel, Francesc Xavier
  • Capdevila Paramio, Roser
  • Oliva Llena, Asensio
In this study, we develop a machine-learning-based data-driven model, which predicts comfort-related flow parameters in a ventilated room. The model is based on the results of high-fidelity computational fluid dynamics (CFD) simulations with different geometrical configurations and boundary conditions. The developed model could be used as a cheaper alternative to CFD for applications where rapid predictions of complex flow configurations are required, such as model predictive control. Even though the developed model provides acceptable accuracy for most of the tested configurations, more input data is required to improve the model performance., This work is supported by the Ministerio de Economía y Competitividad, Spain [ENE2017-88697-R]. N. Morozova is supported by the by the Ministerio de Economía y Competitividad, Spain [FPU16/06333 predoctoral contract]. Part of the calculations was performed on the MareNostrum 4 supercomputer at the Barcelona Supercomputing Center [RES project IM-2021-1-0015]., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

An energy-preserving level set method for multiphase flows

  • Valle Marchante, Nicolás
  • Trias Miquel, Francesc Xavier
  • Castro González, Jesús
The computation of multiphase flows presents a subtle energetic equilibrium between potential (i.e., surface) and kinetic energies. The use of traditional interface-capturing schemes provides no control over such a dynamic balance. In the spirit of the well-known symmetry-preserving and mimetic schemes, whose physics-compatible discretizations rely upon preserving the underlying mathematical structures of the space, we identify the corresponding structure and propose a new discretization strategy for curvature. The new scheme ensures conservation of mechanical energy (i.e., surface plus kinetic) up to temporal integration. Inviscid numerical simulations are performed to show the robustness of such a method., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Proper SGS heat flux models and numerical methods for LES

  • Trias Miquel, Francesc Xavier
  • Santos Serrano, Daniel
  • Dabbagh, Firas
  • Gorobets, Andrei
  • Oliva Llena, Asensio
In this work, we aim to shed light to the following research question: can we find a nonlinear tensorial subgrid-scale (SGS) heat flux model with good physical and numerical properties, such that we can obtain satisfactory predictions for buoyancy-driven turbulent flows? This is motivated by our findings showing that the classical (linear) eddy-diffusivity assumption fails to provide a reasonable approximation for the actual SGS heat flux: namely, a priori analysis for air-filled Rayleigh-Bénard convection (RBC) clearly shows a strong misalignment. In the quest for more accurate models, we firstly study and confirm the suitability of the eddy-viscosity assumption for RBC carrying out a posteriori tests for different models at very low Prandtl numbers (liquid sodium, Pr=0.005) where no heat flux SGS activity is expected. Then, a new tensorial SGS heat flux model is proposed and studied a priori using DNS data of an air-filled (Pr=0.7) RBC at Rayleigh numbers up to 1011. Apart from having good alignment trends with the actual SGS heat flux, it is numerically stable per se and has the proper cubic nearwall behavior. Our near future research plans include testing a posteriori this new tensorial SGS heat flux model. Prior to that, we also aim to properly discretize these models in space and time., F.X.T., F.D. and A.O. have been supported by the Ministerio de Economía y Competitividad, Spain, ANUMESOL project (ENE2017-88697-R). F.X.T. and A.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722) and by the Clean Sky 2 Joint Undertaking, ANTIFOD project (grant ID 821352). F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). D.S. is supported by an FI AGAUR-Generalitat de Catalunya grant (2020FI B 00839). Calculations were performed on the MareNostrum 4 supercomputer at the BSC. The authors thankfully acknowledge these institutions., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Energy preserving multiphase flows: applications to falling films

  • Valle Marchante, Nicolás
  • Trias Miquel, Francesc Xavier
  • Castro González, Jesús
The numerical simulation of multiphase flows presents several challenges, namely the transport of different phases within de domain and the inclusion of capillary effects. Here, these are approached by enforcing a discrete physics-compatible solution. Extending our previous work on the discretization of surface tension [N. Valle, F. X. Trias, and J. Castro, 'An energy-preserving level set method for multiphase flows,' J. Comput. Phys., vol. 400, p. 108991, 2020] with a consistent mass and momentum transfer a fully energy-preserving multiphase flow method is presented. This numerical technique is showcased within the simulation of a falling film under several working conditions related to the normal operation of LiBr absorption chillers., The authors acknowledge the computing resources provided by the Barcelona Supercomputing Center under contracts IM-2019-3-0026 and IM-2020-1-0006. An also grants from the Ministerio de Economía y Competitividad, Spain under contracts ENE2015-70672-P and ENE2017-88697-R. N. Valle also acknowledges an FI AGAUR-Generalitat de Catalunya fellowship under contract 2017FI B 00616, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A new general method to compute dispersion errors on Cartesian stretched meshes for both linear and non-linear operators

  • Ruano Pérez, Jesús
  • Baez Vidal, Aleix
  • Rigola Serrano, Joaquim
  • Trias Miquel, Francesc Xavier
The present article presents a new analysis for the dispersion error and the methodology to evaluate it numerically. Here we present the spectral properties of several convective schemes, including non-linear ones, on Cartesian stretched grids for linear advection problems. Results obtained with this method when applied to uniform structured meshes, converge to the results obtained with the classical method for all the studied schemes. Additionally, effects on the time step depending on which scheme is used are considered using the proposed method. The extracted conclusions taken into account both errors and computational cost allow to propose an optimal scheme according to the selected meshing strategy., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.R.P. is supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain. F.X.T. was supported by a Ramón y Cajal postdoctoral Contract (No. RYC-2012-11996) financed by the Ministerio de Economía y Competitividad, Spain., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

DNS of unequal size droplets collision using a moving-mesh/level-set method

  • Amani, Ahmad
  • Balcázar Arciniega, Néstor
  • Gutierrez, Enrique
  • Oliva Llena, Asensio
The dynamics of binary droplets collision is of huge importance in different fields, from multiphase reactors (Dudukovic et al in Chem Eng Sci 54:1975–1995, 1999 [11]), raindrop formation, ink-jet printing, spray combustion, emulsion stability, turbine blade cooling, spray coating (Ashgriz and Poo in J Fluid Mech 221:183–204, 1990 [5]), and to drug delivery. Due to the complexity of the nature of droplets collision, this topic is one of the most challenging areas in the field of fluid dynamics., We acknowledge Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación, Spain (ENE2017-88697-R). A. Amani acknowledges the financial support of (AGAUR) of Generalitat de Catalunya research scholarship (2016 FI_B 01059). N. Balcázar acknowledges the Programa Torres Quevedo MINECO (PTQ-14-07186)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On a Proper Tensorial Subgrid Heat Flux Model

  • Trias Miquel, Francesc Xavier
  • Dabbagh, Firas
  • Santos Serrano, Daniel
  • Gorobets, Andrei
  • Oliva Llena, Asensio
In this work, we aim to shed light to the following research question: can we find a nonlinear tensorial subgrid-scale (SGS) heat flux model with good physical and numerical properties, such that we can obtain satisfactory predictions for buoyancy-driven turbulent flows? This is motivated by our findings showing that the classical (linear) eddy-diffusivity assumption, q eddy ¿ ¿T, fails to provide a reasonable approximation for the actual SGS heat flux, q = uT - uT: namely, a priori analysis for airfilled Rayleigh-Bénard convection (RBC) clearly shows a strong misalignment. In the quest for more accurate models, we firstly study and confirm the suitability of the eddy-viscosity assumption for RBC carrying out a posteriori tests for different models at very low Prandtl numbers (liquid sodium, Pr = 0.005) where no heat flux SGS activity is expected. Then, different (nonlinear) tensor-diffusivity SGS heat flux models are studied a priori using DNS data of an air-filled (Pr = 0.7) RBC at Rayleigh numbers up to 1011. Apart from having good alignment trends with the actual SGS heat flux, we also restrict ourselves to models that are numerically stable per se and have the proper cubic near-wall behavior. This analysis leads to a new family of SGS heat flux models based on the symmetric positive semi-definite tensor GGT where G = ¿u, i.e. q ¿ GGT¿T, and the invariants of the GGT tensor. Finally, relevant numerical aspects regarding the implementation of this type of models are discussed in detail. A list of physical and numerical properties is identified and subsequently imposed, leading to a symmetrypreserving discretization that is based on discrete operators already available in any CFD code., F.X.T., F.D. and A.O. have been financially supported by the Ministerio de Economía y Competitividad, Spain, ANUMESOL project (ENE2017-88697-R). F.X.T. and A.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722). F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). D.S. is supported by an FI AGAUR-Generalitat de Catalunya fellowship (2020FI B 00839). Calculations have been performed on the IBM MareNostrum 4 supercomputer at the BSC (PRACE 15th Call, Ref. 2016163972, “Exploring new frontiers in Rayleigh-Bénard convection” and Tier-1 RES projects IM-2020-2-0029 & IM-2020-3-0030 “Direct and Large-Eddy Simulation of buoyancy-driven turbulence in liquid metals”). The authors thankfully acknowledge these institutions., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On the Interpolation Problem for the Poisson Equation on Collocated Meshes

  • Santos Serrano, Daniel
  • Muela Castro, Jordi
  • Valle Marchante, Nicolás
  • Trias Miquel, Francesc Xavier
The appearence of unphysical velocities in highly distorted meshes is a common problem in many simulations. In collocated meshes, this problem arises from the interpolation of the pressure gradient from faces to cells. Using an algebraic form for the classical incompressible Navier-Stokes equations, this problem is adressed. Starting from the work of F. X. Trias et. al. [FX.Trias et al. JCP 258: 246-267, 2014], a new approach for studying the Poisson equation obtained using the Fractional Step Method is found, such as a new interpolator is proposed in order to found a stable solution, which avoid the appearence of these unpleasant velocities. The stability provided by the interpolator is formally proved for cartesian meshes and its rotations, using fully-explicit time discretizations. The construction of the Poisson equation is supported on mimicking the symmetry properties of the differential operators and the Fractional Step Method. Then it is reinterpreted using a recursive application of the Fractional Step Method in order to study the system as an stationary iterative solver. Furthermore, a numerical analysis for unstructured mesh is also provided., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (project ref. ENE2017-88697-R). D. Santos acknowledges a FI AGAUR-Generalitat de Catalunya fellowship (2020FI B 00839), and N. Valle also acknowledges a FI AGAUR-Generalitat de Catalunya fellowship (2017FI B 00616). The authors thankfully acknowledge these institutions., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A method for fluid-structure interaction problems with non-Newtonian fluid

  • Amani, Ahmad
  • Naseri, Alireza
  • Pérez Segarra, Carlos David
  • Oliva Llena, Asensio
This paper represents a numerical method to solve fluid-structure interaction (FSI) problems where the fluid exhibits a non-Newtonian Viscoelastic behaviour. Oldroyd-B constitutive equation is used to model Viscoelastic fluid. For FSI solution, a semi-implicit partitioned method is used which separates the fluid pressure term and strongly couples it to the structure, while the remaining fluid terms are only weakly coupled. Numerical tests demonstrate the capability of the method to solve FSI problems with a non-Newtonian Viscoelastic behaviour of the fluid., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Simulation of fluid-structure interaction and impact force on a reed valve

  • Castrillo Green, Pablo
  • Schillaci, Eugenio
  • Rigola Serrano, Joaquim
The cyclic impact force between a reed valve and the seat plate is the main reason of the valve failure in many thermo-technical devices as compressors, engines, etc. According to experimental observations the latter is due to fatigue and usually occurs in the leading part of the valve ‘neck’. In this work, a complex numerical analysis is presented aimed to studying the external forces and internal stresses suffered by the valve. In particular, the impact force between the valve and the seat is studied. The numerical analysis relies on the coupled synergy of two different simulation concepts. In order to do so, two codes are used: (1) first, the in-house Computational Fluid Dynamics (CFD) code presented in [1] is employed to simulate the Fluid-Structure Interaction (FSI) between gas and valve, extracting reference data for valve displacement and external gas pressures; (2) second, the analysis of the internal structure stresses, together with the impact forces with the plate is implemented in a Computational Solid Dynamics (CSD) code developed in FreeFEM++ [2]. The impact force representation is based on the formulation presented in [3] where a conserving algorithm for frictionless dynamic contact/impact is developed. Due to the importance of obtaining an adequate impact force, an exhaustive study is carried out on its characterization in terms of numerical parameters, such as the penalty stiffness. Under this framework, the valve displacement and impact velocities are verified. Hence, impact forces are analysed in different scenarios, obtaining interesting observations about stresses distribution, with a particular focus on the points where failure is experienced., The authors acknowledge Voestalpine Precision Strip AB company for the previous research collaboration project that allowed to validate experimentally the presented numerical methods. P. Castrillo gratefully acknowledges the Universitat Politecnica de Catalunya and Banco Santander for the financial ` support of his predoctoral grant FPI-UPC (109 FPI-UPC 2018). E. Schillaci acknowledges the financial support of the Programa Torres Quevedo (PTQ2018-010060). This work has also been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A hierarchical parallel implementation for heterogeneous computing. Application to algebra-based CFD simulations on hybrid supercomputers

  • Álvarez Farré, Xavier
  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier
The quest for new portable implementations of simulation algorithms is motivated by the increasing variety of computing architectures. Moreover, the hybridization of high-performance computing systems imposes additional constraints, since heterogeneous computations are needed to efficiently engage processors and massively-parallel accelerators. This, in turn, involves different parallel paradigms and computing frameworks and requires complex data exchanges between computing units. Typically, simulation codes rely on sophisticated data structures and computing subroutines, so-called kernels, which makes portability terribly cumbersome. Thus, a natural way to achieve portability is to dramatically reduce the complexity of both data structures and computing kernels. In our algebra-based approach, the scale-resolving simulation of incompressible turbulent flows on unstructured meshes relies on three fundamental kernels: the sparse matrix-vector product, the linear combination of vectors and the dot product. It is noteworthy that this approach is not limited to a particular kind of numerical method or a set of governing equations. In our code, an auto-balanced multilevel partitioning distributes workload among computing devices of various architectures. The overlap of computations and multistage communications efficiently hides the data exchanges overhead in large-scale supercomputer simulations. In addition to computing on accelerators, special attention is paid at efficiency on manycore processors in multiprocessor nodes with significant non-uniform memory access factor. Parallel efficiency and performance are studied in detail for different execution modes on various supercomputers using up to 9,600 processor cores and up to 256 graphics processor units. The heterogeneous implementation model described in this work is a general-purpose approach that is well suited for various subroutines in numerical simulation codes., The work of A. G. has been funded by the Russian Sci- ence Foundation, project 19-11-00299. The work of X. Á. F. and F. X. T. has been financially supported by the ANUMESOL project (ENE2017-88697-R) by the Spanish Research Agency, and the FusionCAT project (0 01-P-0 01722) by the Government of Catalo- nia RIS3CAT FEDER. X. Á. F. is supported by a predoctoral contract (2019FI_B2-0 0 076) by the Government of Catalonia. The work has been carried out using the MareNostrum 4 supercomputer of the Barcelona Supercomputing Center; the TSUBAME3.0 supercom-puter of the Global Scientific Information and Computing Center at Tokyo Institute of Technology; the Lomonosov-2 supercomputer of the shared research facilities of HPC computing resources at Lomonosov Moscow State University; the K-60 hybrid cluster of the Collective Usage Centre of KIAM RAS. The authors thankfully acknowledge these institutions., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

An efficient two-layer wall model for high Reynolds number large eddy simulation

  • Calafell Sandiumenge, Joan
  • Trias Miquel, Francesc Xavier
  • Oliva Llena, Asensio
Wall-bounded flows at high Reynolds number are an important research field given that they are present in many important industrial applications. Nonetheless, the use of accurate numerical methodologies such as Large Eddy Simulation (LES) for routine industrial applications, is still unfeasible due to their heavy computational cost. Wall-Modeled LES is intended to circumvent the massive costs of accurately resolving the boundary layer while benefiting from the temporal and spatial resolution of an LES computation. In this work, a Two-Layer Wall Model with a general formulation suitable for non-equilibrium flows and complex geometries is presented. The Two-Layer Models (TLM) suffer from two recurrent problems, the ”log-layer mismatch” (LLM) and the resolved Reynolds stresses inflow (RRSI). Until now, complex and expensive techniques have been proposed to overcome these problems separately. In the present work, a timeaveraging filter (TAF) is considered to deal with both issues at once, with a single and low-computational-cost technique. It is the first time that the TAF technique is used to block the RRSI. In this regard, a numerical experiment is initially performed to assess the TAF ability in doing so. Afterward, the WM is tested in regular operating conditions with a Ret ˜ 3000 pipe flow case. Good results are obtained in all the performed tests, showing the capability of the TAF of suppressing the LLM while avoiding the RRSI at the same time. This makes the new TLM methodology a very effcient technique compared to other implementations proposed so far., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

NUMA-Aware Strategies for the Heterogeneous Execution of SPMV on Modern Supercomputers

  • Álvarez Farré, Xavier
  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier
  • Oliva Llena, Asensio
The sparse matrix-vector product is a widespread operation amongst the scientific computing community. It represents the dominant computational cost in many large-scale simulations relying on iterative methods, and its performance is sensitive to the sparse pattern, the storage format, and kernel implementation, and the target computing architecture. In this work, we are devoted to the efficient execution of the sparse matrix-vector product on (potentially hybrid) modern supercomputers with non-uniform memory access configurations. A hierarchical parallel implementation is proposed to minimize the number of processes participating in distributed-memory parallelization. As a result, a single process per computing node is enough to engage all its hardware and ensure efficient memory access on manycore platforms. The benefits of this approach have been demonstrated on up to 9,600 cores of MareNostrum 4 supercomputer, at Barcelona Supercomputing Center., The work of A. Gorobets has been funded by the Russian Science Foundation, project 19- 11-00299. The work of X. Alvarez-Farr ´ e, F. X. Trias and A. Oliva has been financially supported ´ by the ANUMESOL project (ENE2017-88697-R) by the Spanish Research Agency (Ministerio de Economía y Competitividad, Secretaría de Estado de Investigacion, Desarrollo e Inno- ´ vacion), and the FusionCAT project (001-P-001722) by the Government of Catalonia (RIS3CAT ´ FEDER). The studies of this work have been carried out using the MareNostrum 4 supercomputer of the Barcelona Supercomputing Center (projects IM-2020-2-0029 and IM-2020-3-0030); the TSUBAME3.0 supercomputer of the Global Scientific Information and Computing Center at Tokyo Institute of Technology; the Lomonosov-2 supercomputer of the shared research facilities of HPC computing resources at Lomonosov Moscow State University; the K-60 hybrid cluster of the collective use center of the Keldysh Institute of Applied Mathematics. The authors thankfully acknowledge these institutions for the compute time and technical support., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A scalable framework for the partitioned solution of fluid-structure interaction problems

  • Naseri, Alireza
  • Totounferoush, Amin
  • González Acedo, Ignacio
  • Mehl, Miriam
  • Pérez Segarra, Carlos David
In this work, we present a scalable and efficient parallel solver for the partitioned solution of fluid–structure interaction problems through multi-code coupling. Two instances of an in-house parallel software, TermoFluids, are used to solve the fluid and the structural sub-problems, coupled together on the interface via the preCICE coupling library. For fluid flow, the Arbitrary Lagrangian–Eulerian form of the Navier–Stokes equations is solved on an unstructured conforming grid using a second-order finite-volume discretization. A parallel dynamic mesh method for unstructured meshes is used to track the moving boundary. For the structural problem, the nonlinear elastodynamics equations are solved on an unstructured grid using a second-order finite-volume method. A semi-implicit FSI coupling method is used which segregates the fluid pressure term and couples it strongly to the structure, while the remaining fluid terms and the geometrical nonlinearities are only loosely coupled. A robust and advanced multi-vector quasi-Newton method is used for the coupling iterations between the solvers. Both the fluid and the structural solver use distributed-memory parallelism. The intra-solver communication required for data update in the solution process is carried out using non-blocking point-to-point communicators. The inter-code communication is fully parallel and point-to-point, avoiding any central communication unit. Inside each single-physics solver, the load is balanced by dividing the computational domain into fairly equal blocks for each process. Additionally, a load balancing model is used at the inter-code level to minimize the overall idle time of the processes. Two practical test cases in the context of hemodynamics are studied, demonstrating the accuracy and computational efficiency of the coupled solver. Strong scalability test results show a parallel efficiency of 83% on 10,080 CPU cores., This work was financially supported by—Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación, Spain (ENE2017-88697-R),—priority program 1648—Software for Exascale Computing 214 (ExaFSA - Exascale Simulation of Fluid–Structure–Acoustics Interactions) of the German Research Foundation,—and a FI Ph.D. scholarship by the Agència de Gestió d’Ajuts Universitaris i de Recerca (AGAUR) of Generalitat de Catalunya (Spain). The performance measurements were carried out on the SuperMUC supercomputer at Leibniz Rechenzentrum (LRZ) der Bayerischen Akademie der Wissenschaften. The authors wish to thank LRZ for the computing time and the technical support., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On the Feasibility of CFD for Transient Air Flow Simulations in Buildings

  • Morozova, Nina
  • Capdevila Paramio, Roser
  • Trias Miquel, Francesc Xavier
  • Oliva Llena, Asensio
The rapidly growing computational capacity hasmade CFD simulations an attractive tool for indoorenvironmental applications. The ability of CFD toperform transient simulations could be incorporatedinto model predictive control systems for buildings inorder to correctly reproduce prompt disturbances inthe air field, such as opening doors and windows orchanges in occupants behaviour. In this work, twocharacteristic configurations which mimic typical air-flow patterns inside buildings are studied using dif-ferent grid sizes and turbulence models. Case one isa tall turbulent differentially heated cavity and casetwo is the turbulent mixed convection in a ventilatedsquare cavity. The Spearman’s rank correlation coef-ficient for transient simulations is compared againstcomputational time for different CFD approaches,and the possibility of performing real-time simula-tions is evaluated. Among different turbulence mod-els studied, the no-model approach with symmetrypreserving discretization has shown the best overallperformance in terms of computational cost and ac-curacy of the results., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Advanced techniques for grau area mitigation in DES simulations and their effectes on the subsonic round jet acoustic spectra, Tècniques avançades per la mitigació de la zona grisa en simulacions DES i els seus efectes en l'espectre acústic del jet circular

  • Duben, Alexey
  • Ruano Pérez, Jesús
  • Trias Miquel, Francesc Xavier
  • Rigola Serrano, Joaquim
The research dedicated to the investigation of different gray-area mitigation approaches towards accurate aerodynamics and aeroacoustics is presented. The recent modifications of hybrid RANS-LES DDES approach based on combinations of new adapting subgrid length scales (~ !, SLA and lsq) and LES models ( and S3QR) are considered. The object of investigation is an immersed subsonic turbulent jet. The simulations are carried out on a set of refining meshes using two different scale-resolving numerical algorithms realized in the compressible codes NOISEtte and OpenFOAM. The evaluation of different approaches is focused on the analysis of far field noise. The results show that all the considered techniques provide appropriate accuracy to predict the noise generated by the turbulent jet. The study clearly demonstrated the importance of both numerical scheme and subgrid turbulence model. The peculiarities of considered approaches are revealed and discussed., A.D. was supported by Moscow Center for Fundamental and Applied Mathematics, Agreement with the Ministry of Science and Higher Education of the Russian Federation, No. 075-15-2019-1623. The NOISEtte computations were carried out using the equipment of the shared research facilities of HPC computing resources at Lomonosov Moscow State University and the computing resources of the federal collective usage center Complex for Simulation and Data Processing for Mega-science Facilities at NRC ”Kurchatov Institute” (http://ckp.nrcki.ru/). J.Ru. was supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain. J.Ru. and F.X.T. have been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.Ru., F.X.T. and J.Ri. are also supported by the Clean Sky 2 Joint Undertaking. ANTIFOD project (Grant ID 821352)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the feasibility of affordable high-fidelity CFD simulations for indoor environment design and control

  • Morozova, Nina
  • Trias Miquel, Francesc Xavier
  • Capdevila Paramio, Roser
  • Pérez Segarra, Carlos David
  • Oliva Llena, Asensio
Computational fluid dynamics (CFD) is a reliable tool for indoor environmental applications. However, accurate CFD simulations require large computational resources, whereas significant cost reduction can lead to unreliable results. The high cost prevents CFD from becoming the primary tool for indoor environmental simulations. Nonetheless, the growth in computational power and advances in numerical algorithms provide an opportunity to use accurate and yet affordable CFD. The objective of this study is to analyze the feasibility of fast, affordable, and high-fidelity CFD simulations for indoor environment design and control using ordinary office computers. We analyze two representative test cases, which imitate common indoor airflow configurations, on a wide range of different turbulence models and discretizations methods, to meet the requirements for the computational cost, run-time, and accuracy. We consider statistically steady-state simulations for indoor environment design and transient simulations for control. Among studied turbulence models, the no-model and large-eddy simulation with staggered discretizations show the best performance. We conclude that high-fidelity CFD simulations on office computers are too slow to be used as a primary tool for indoor environment design and control. Taking into account different laws of computer growth prediction, we estimate the feasibility of high-fidelity CFD on office computers for these applications for the next decades, This work is supported by the Ministerio de Economía y Competitividad, Spain [ENE2017-88697-R]. N. Morozova is supported by the by the Ministerio de Economía y Competitividad, Spain [FPU16/06333 predoctoral contract]. Part of the calculations was performed on the MareNostrum 4 supercomputer at the Barcelona Supercomputing Center [RES project I-2019-2-0021]. The authors thankfully acknowledge these institutions. The authors would also like to thank our colleague MSc Xavier Álvarez Farré for the productive discussions., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A highly portable heterogeneous implementation of a Poisson solver for flows with one periodic direction

  • Alsalti Baldellou, Àdel
  • Trias Miquel, Francesc Xavier
  • Álvarez Farré, Xavier
  • Oliva Llena, Asensio
The portability of codes has become a major advantage given the continuous development of new architectures for numerical applications, as well as the progressive incorporation of accelerators in modern supercomputers. Following this trend, we have adopted an algebraic approach in the implementation of a Poisson solver for incompressible flows with one periodic direction. This approach, which basically consists of adapting a reduced set of fundamental operations to any architecture (such as the sparse matrixvector product or the dot product of two vectors), allows us to efficiently port our applications to any heterogeneous supercomputers in an easy manner. More particularly, our three-dimensional solver takes advantage of the existing periodic dimension (by means of a Fourier decomposition) to later execute overlapped data transpositions among devices, which conveniently share the workload with their CPU hosts, and solve the resulting two-dimensional decoupled subsystems., The work has been financially supported by a competitive R+D project (ENE2017- 88697-R) by the Spanish Research Agency. A.A.B is supported by a predoctoral contract (DIN2018-010061) by the Ministry of Science, Innovation and Universities of Spain (MICINN) and X.A.F. by the by the Government of Catalonia (2019FI_B2-00076)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Flow topology dynamics in a three-dimensional phase space for turbulent Rayleigh-Bénard convection

  • Dabbagh, Firas
  • Trias Miquel, Francesc Xavier
  • Gorobets, Andrei
  • Oliva Llena, Asensio
F.X.T., F.D. and A.O. are financially supported by the Ministerio de Economía y Competitividad, Spain (ENE2017-88697-R). F.X.T. is supported by a Ramón y Cajal postdoctoral contract (RYC-2012-11996). F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). Calculations have been performed on the IBM MareNostrum 4 supercomputer at the BSC (PRACE 15th Call, Ref. 2016163972, \Exploring new frontiers in Rayleigh-Bénard convection"). Preliminary simulations were carried out using computational resources of MCC NRC \Kurchatov Institute", http://computing.nrcki.ru/. The authors thankfully acknowledge these institutions., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Three-dimensional direct numerical simulation (dns) Of taylor bubbles rising in non-Newtonian environments

  • Amani, Ahmad
  • Castro González, Jesús
  • Oliva Llena, Asensio
Three-dimensional numerical simulation of Taylor gas bubbles as primary unites of slug flow patterns rising in non-Newtonian environments is performed in the context of Direct Numerical Simulation (DNS) of the governing equations, where the whole physics of fluid motions will be taken into account. State-of-the-art numerical tools are proposed to tackle the numerical challenges in the DNS study of this problem. E.g. a coupled level-set volume-of-fluid (CLSVOF) interface capturing method is used to solve the topological changes of the interface. Physical formulations are integrated with moving-mesh (MM) technique to decrease the computational cost of 3D simulations and adaptivemesh-refinement (AMR) technique to increase the local accuracy around the interface. The governing equations are solved using High-Performance Computing (HPC) parallel approaches. To the best of the authors’ knowledge, this is the first work dealing with three-dimensional direct numerical simulation of Taylor bubbles rising in non-Newtonian environments., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Comparison of Sliding Mesh and Immersed Boundary Methods in Unsteady Simulations

  • Vera i Fernández, Jordi
  • Muela Castro, Jordi
  • Favre, Federico
  • Oliet Casasayas, Carles
The feasibility and accuracy of two methods for simulating moving bodies inside a fluid are studied. Different cases are presented using the Immersed Boundary Method and the Sliding Mesh technique. The results obtained by both methods are compared and assessed. These results allow to study the accuracy of both methods as well as their computational feasibility, in terms of computation time, mesh requirements and parallel scalability., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Assessment of LES techniques for mitigating the Grey Area in DDES models

  • Pont Vilchez, Arnau
  • Santos Serrano, Daniel
  • Trias Miquel, Francesc Xavier
  • Duben, Alexey
  • Revell, Alistair
  • Oliva Llena, Asensio
The slow RANS-LES transition is a well-known shortcoming in hybrid turbulence models such as DelayedDetached Eddy Simulation (DDES). The present work assesses the feasibility of 2D sensitive LES models for naturally triggering turbulence, rather than using the specifically designed techniques available in the literature. This research has been carried out with OpenFOAM, which has been used for simulating the flow in a Backward-Facing Step configuration. The results have been compared with a DNS data set, showing the good mitigation capabilities of such LES techniques. Nevertheless, other cases should be studied before extracting any relevant conclusion., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017- 88697-R). A.P.V. is supported by a FI-DGR 2016 predoctoral contract (No. 2018FI_B2_00072) financed by Generalitat de Catalunya, Spain. F.X.T. is supported by a Ramón y Cajal postdoctoral Contract (No. RYC-2012-11996) financed by the Ministerio de Economía y Competitividad, Spain., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On a physically-consistent nonlinear subgrid-scale heat flux model for LES of buoyancy driven flows

  • Trias Miquel, Francesc Xavier
  • Dabbagh, Firas
  • Gorobets, Andrei
  • Oliva Llena, Asensio
Small-scale dynamics is the spirit of turbulence physics. It delivers complex mechanisms when turbulence is purely sustained by buoyancy. This takes place in Rayleigh-Bénard convection (RBC). Most of the existing RBC dynamics is ruled by hard turbulent regime and a deep understanding of small scale dynamics with its relevant nonlinearities, is still unsatis¿ed. To do so, the evolution of QG =-1/2tr(G2) and RG =-1/3tr(G3), invariants of the velocity gradient tensor, G = Gradu u u, in their phase space{QG,RG}, were studied and reported in Dabbagh et al. [1] using DNS of RBC. In the present work, we expand this 2D {QG,RG} evolution to 3D by decomposing RG into its strain production RS = -1/3tr(S3) andenstrophyproductiontr(¿2S) =RS-RG terms, where S and ¿ aretherate-of-strainandrate-of-rotation tensors, respectively. In the {QG,RS,RS-RG} space, the ¿ow topology in a Lagrangian evolution is changing by the conditionalmeantrajectories(CMTs){DQG/Dt,DRS/Dt,D(RS-RG)/Dt}. Usingthedatasetin[1],andfromFigure46: anidenti¿edcyclicalstartoftrajectoriesisdistinguishedinareasofvortex-stretchingRS-RG >0andRS >0inthestrain dominated slots (QG < 0), which becomes stronger and longer expanded at Rayleigh number Ra = 1010. Afterwards, the trajectories move downwards (QG << 0) in areas of vortex-compression RS-RG < 0 and RS > 0, that also become more diverging at Ra = 1010 as a result of the self-ampli¿ed straining [1]. This is followed by rising trajectories upwards (QG > 0) to continue performing the typical planner {QG,RG} cyclical behaviour [1], next to RS = 0, and decaying towards the origin. DNS at Ra = 1011 is currently being computed on the MareNostrum supercomputer [2]. Results will be presented during the conference., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

NUMA-Aware strategies for the efficient execution of CFD simulations on CPU supercomputers

  • Álvarez Farré, Xavier
  • Gorobets, Andrei
  • Trias Miquel, Francesc Xavier
  • Oliva Llena, Asensio
The growing variety of computing architectures and the hybridization of high-performance computing systems encourage the research for portable implementations of numerical methods in simulation codes. However, the pursuit of efficient and portable implementations is a rather complex problem. The present work is devoted to the development of portable parallel algorithms, primarily for scale-resolving, time-accurate simulations of incompressible flows with turbulent heat and mass transfer. The heterogeneous computing capability allows for engaging both processors and accelerators efficiently. In addition to computing on accelerators, special attention is paid at efficiency on multiprocessor nodes with significant non-uniform memory access factor. In this work, we study in detail the parallel efficiency and performance for different execution modes on up to ten thousand cores of MareNostrum 4 supercomputer., The work has been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency. X. A. F. is supported by a predoctoral contract (2019FI B2-00076) by the Government of Catalonia. The work has been carried out using the computing resources of the Barcelona Supercomputing Center (MareNostrum 4); The authors thankfully acknowledge the institution., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A GPU Accelerated Framework for Partitioned Solution of Fluid-Structure Interaction Problems

  • Totounferoush, Amin
  • Naseri, Alireza
  • Chiva Segura, Jorge
  • Oliva Llena, Asensio
  • Mehl, Miriam
We present a GPU-accelerated solver for the partitioned solution of fluid-structure interaction (FSI) problems. Independent scalable fluid and structure solvers are coupled by a library which handles the inter-code data communication, mapping and equation coupling. A coupling strategy is incorporated which allows accelerating expensive components of the coupled framework by offloading them to GPUs. To prove the efficiency of the proposed coupling strategy in conjunction with the offloading scheme, we present a numerical performance analysis for a complex test case in the filed of biomedical engineering. The numerical experiments demonstrate an excellent speed-up in the accelerated kernels (up to 133 times) which results in 6 to 8 times faster overall simulations. In addition, we observed a very good reduction in total simulation time by increasing the exploited compute nodes up to 8 (complete machine capacity)., We thank the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) for supporting this work by funding - EXC2075 – 390740016 under Germany’s Excellence Strategy. We acknowledge the support by the Stuttgart Center for Simulation Science (SimTech). This work was also financially supported by • priority program 1648 - Software for Exascale Computing 214 (ExaFSA - Exascale Simulation of Fluid-Structure-Acoustics Interactions) of the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation), • Ministerio de Economía y Competitividad, Secretaría de Estado de Investigacion, Desarrollo e ´ Innovacion, Spain (ENE2017-88697-R). ´ The performance measurements were carried out on the Vulcan cluster at the High-Performance Computing Center Stuttgart (HLRS). The authors wish to thank HLRS for compute time and technical support., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

An enhanced finite volume based solver for thermoelastic materials in fluid-structure coupled problems

Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the implementation of flux limiters in algebraic frameworks

  • Valle Marchante, Nicolás
  • Álvarez Farré, Xavier
  • Gorobets, Andrei
  • Castro González, Jesús
  • Oliva Llena, Asensio
  • Trias Miquel, Francesc Xavier
The use of flux limiters is widespread within the scientific computing community to capture shock dis- continuities and are of paramount importance for the temporal integration of high-speed aerodynamics, multiphase flows and hyperbolic equations in general. Meanwhile, the breakthrough of new computing architectures and the hybridization of supercomputer systems pose a huge portability challenge, particularly for legacy codes, since the computing subroutines that form the algorithms, the so-called kernels, must be adapted to various complex parallel program- ming paradigms. From this perspective, the development of innovative implementations relying on a minimalist set of kernels simplifies the deployment of scientific computing software on state-of-the-art supercomputers, while it requires the reformulation of algorithms, such as the aforementioned flux lim- iters. Equipped with basic algebraic topology and graph theory underlying the classical mesh concept, a new flux limiter formulation is presented based on the adoption of algebraic data structures and kernels. As a result, traditional flux limiters are cast into a stream of only two types of computing kernels: sparse matrix-vector multiplication and generalized pointwise binary operators. The newly proposed formulation eases the deployment of such a numerical technique in massively parallel, potentially hybrid, computing systems and is demonstrated for a canonical advection problem., The work of N. V. and X. Á. F. has been supported by the Government of Catalonia, FI AGAUR predoctoral grants 2019FI_B2_ 000104 and 2019FI_B2_00076. N. V., X. Á. F., J. C., A. O. and F. X. T. have been funded by the Spanish Research Agency, ANUMESOL project ENE2017-88697-R. J. C. has also been funded by Spanish Research Agency, GALIFLOW project ENE2015-70662-P. The studies of this work have been carried out using the MareNostrum 4 supercomputer of the Barcelona Supercomput- ing Center, projects IM-2019-3-0026 and IM-2020-1-0006; the TSUBAME3.0 supercomputer of the Global Scientific Information and Computing Center at Tokyo Institute of Technology; the Lomonosov-2 supercomputer of the shared research facilities of HPC computing resources at Lomonosov Moscow State University; the K-60 hybrid cluster of the collective use center of the Keldysh Institute of Applied Mathematics; the JFF cluster of the Heat and Mass Transfer Technological Center at Technical University of Cat- alonia. The authors thankfully acknowledge these institutions for the compute time and technical support., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

On Preconditioning Variable Poisson Equation with Extreme Contrasts in the Coefficients

  • Alsalti Baldellou, Àdel
  • Trias Miquel, Francesc Xavier
  • Gorobets, Andrei
  • Oliva Llena, Asensio
It is well known that the solution by means of iterative methods of very ill-conditioned systems leads to very poor convergence rates. In this context, preconditioning becomes crucial in order to modify the spectrum of the system being solved and improve the performance of the solvers. A proper balance between the reduction in the number of iterations and the overhead of the construction and application of the preconditioner needs to be sought to actually decrease the total execution time of the solvers. This is particularly important when considering variable coefficients matrices as, in general, its preconditioners will also be variable and need to be updated regularly at an affordable cost. In this work we present a family of variable preconditioners designed for the effective solution of variable Poisson equation with extreme contrasts in the coefficients, which represents a particularly challenging case as it translates into a variable and extremely ill-conditioned system arising in many situations such as with multiphase flows presenting high density ratios or in the presence of highly-stretched adaptive mesh refinements. Finally, the results of the numerical experiments performed are presented and discussed, confirming our preconditioners as extremely affordable, highly-parallelizable and easy-to-implement alternatives to the more standard (and usually unfeasible) preconditioners, still showing great improvements in the rate of convergence of the solvers without requiring the variable coefficients matrix to be explicitly rebuilt at each iteration., Àdel Alsalti-Baldellou, F. Xavier Trias and Assensi Oliva have been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency. Àdel Alsalti-Baldellou is also supported by predoctoral grants DIN2018-010061 and 2019-DI-90, given by, respectively, the Spanish Ministry of Science, Innovation and Universities (MICINN) and the Catalan Agency for Management of University and Research Grants (AGAUR)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

New Strategies for Mitigating the Gray Area in Delayed-Detached Eddy Simulation Models

  • Pont Vilchez, Arnau
  • Duben, Alexey
  • Gorobets, Andrei
  • Revell, Alistair
  • Oliva Llena, Asensio
  • Trias Miquel, Francesc Xavier
This paper presents a new approach for mitigating the unphysical delay in the Reynolds-averaged Navier–Stokes (RANS) to large-eddy simulation (LES) transition, often referred to as the gray area, which is a common issue for hybrid RANS–LES turbulence models such as delayed-detached eddy simulation. An existing methodology designed for improving the LES performance in complex flows is adapted and tested. This is based on reducing the numerical diffusion in critical areas for permitting a more accurate development of turbulence. The new formulation comprises both a two-dimensional sensitive velocity gradient model and an alternative definition of the subgrid length scale, which are tested both individually and in tandem, and compared with the other formulations commonly used for addressing the gray area. Four test cases are examined, a flat plate, two variants of the incompressible backwardfacing step, and an open jet compressible case, all of which are selected to expose the adverse impact of numerical diffusion that this study seeks to address. Furthermore, the proposed changes are implemented in two different codes for the purpose of cross-validation. Encouraging results are observed, supporting the suitability of the new approach as a candidate for addressing the gray area issue in flows of this kind., This work was financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). A.P.V. was supported by an FI-DGR 2016 predoctoral contract (No. 2018FI_ B2_00072) financed by Generalitat de Catalunya, Spain. F.X.T. was supported by a Ramón y Cajal postdoctoral contract (No. RYC-2012- 11996) financed by the Ministerio de Economía y Competitividad, Spain. A.D. and A.G. were supported by Moscow Center for Fundamental and Applied Mathematics, Agreement with the Ministry of Science and Higher Education of the Russian Federation, No. 075- 15-2019-1623. The NOISEtte computations were carried out using the equipment of the shared research facilities of HPC computing resources at Lomonosov Moscow State University and the computing resources of the federal collective usage center Complex for Simulation and Data Processing for Mega-science Facilities at NRC “Kurchatov Institute” (http://ckp.nrcki.ru/)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Detailed prediction of fluid-solid coupled phenomena of turbulent flow through reed valves

  • González Acedo, Ignacio
  • Naseri, Alireza
  • Rigola Serrano, Joaquim
  • Pérez Segarra, Carlos David
  • Oliva Llena, Asensio
The operation of self-actuated valves in suction and discharge processes plays a crucial role in the thermal efficiency and structural reliability of hermetic reciprocating compressors. The present work provides a thorough description of an in-house numerical method based on a partitioned fluid-structure interaction algorithm intended to obtain high-fidelity numerical predictions and optimise valve system design. A large eddy simulation model is used for the turbulent flow, whereas a normal mode superposition assumption along with an impact penalty method is used for the reed. Under this framework, a detailed analysis of the coupled problem with a straight and tapered exit ports is carried out. Differences in effective flow area and pressure drop are found as a result of the port geometry, but also of the valve velocity, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Subgrid-Scale Model Based on the Invariants of the Gradient Model Tensor

  • Folch Flórez, David
  • Trias Miquel, Francesc Xavier
  • Gorobets, Andrei
  • Oliva Llena, Asensio
The incompressible Navier-Stokes equations stand as the best mathematical model for turbulent flows. However, direct numerical simulations at high Reynolds numbers are not yet feasible because the convective term produces far too many relevant scales of motion, thus remaining limited to relatively low-Reynolds numbers. Dynamically less complex mathematical formulations have been developed for coarse-grain simulations, like the well known eddy-viscosity models. Most of these models are based on the combination of invariants of a symmetric tensor that depends on the gradient of the resolved velocity field, G = Ñu, and should properly detect different flow configurations (laminar and 2D flows, near-wall behavior, transitional regime, etc.). Brand-new models have been constructed considering the first three invariants of the symmetric tensor GGT with excellent results;1 hence, it is formally based on the lowest-order approximation of the subgrid stress tensor, t(u) = D2 12GGT +O(D4), i.e. the gradient model proposed by Clark.2 Furthermore, these models have been implemented on a pseudo-spectral algorithm with a fully-explicit second-order time-integration method.3 The performance of this special configuration has been successfully tested for decaying isotropic turbulence and a turbulent channel flow. It is currently being developed for a semi-infinite boundary layer with periodic conditions as a previous step to carry out wind farm simulations. Details of the implementation and numerical results will be presented., The work has been financially supported by a competitive R+D project (ENE2017-88697-R) by the Spanish Research Agency. The authors thankfully acknowledge these institutions., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Investigating the capabilities of CFD-based data-driven models for indoor environmental design and control

  • Morozova, Nina
  • Trias Miquel, Francesc Xavier
  • Capdevila Paramio, Roser
  • Oliva Llena, Asensio
In this work, we study the accuracy of CFD-based data-driven models, which predict comfort-related flow parameters in a ventilated cavity with a heated floor. We compare the computational cost and accuracy of three different models, namely artificial neural network, support vector regression, and gradient boosting regression. The tested scenarios include short and long cavities with different inlet velocities. Among the studied frameworks, the artificial neural network provides the most accurate predictions for most of the tested flow configurations. However, test configurations with jet separation and a secondary vortex are more difficult to predict correctly; thus more high-fidelity data is required in order to construct a more robust and reliable model., This work is supported by the Ministerio de Economía y Competitividad, Spain [ENE2017-88697-R]. N. Morozova is supported by the by the Ministerio de Economía y Competitividad, Spain [FPU16/06333 predoctoral contract]. Part of the calculations was performed on the MareNostrum 4 supercomputer at the Barcelona Supercomputing Center [RES project IM-2021-1-0015]. The authors thankfully acknowledge these institutions., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A General Method to Compute Numerical Dispersion Error

  • Ruano Pérez, Jesús
  • Baez Vidal, Aleix
  • Rigola Serrano, Joaquim
  • Trias Miquel, Francesc Xavier
This article presents a new methodology to compute numerical dispersion error. The analysis here presented is not restricted to uniform structured meshes nor linear discrete operators as it does not rely on sinusoids to compute the associated error. When using uniform meshes, the results obtained with the present method collapse onto the obtained with the classic one via an easy change of basis. If non-uniform meshes are used, a new kind of results are obtained which shed some light onto the role stretching has on dispersion error., This work has been financially supported by the Ministerio de Economía y Competitividad, Spain (No. ENE2017-88697-R). J.R.P. is supported by a FI-DGR 2015 predoctoral contract financed by Generalitat de Catalunya, Spain., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On a Proper Tensor-Diffusivity Model for Large-Eddy Simulation of Buoyancy-Driven Turbulence

  • Trias Miquel, Francesc Xavier
  • Dabbagh, Firas
  • Gorobets, Andrei
  • Oliet Casasayas, Carles
In this work, we aim to shed light to the following research question: can we find a nonlinear tensorial subgrid-scale (SGS) heat flux model with good physical and numerical properties, such that we can obtain satisfactory predic- tions for buoyancy-driven turbulent flows? This is motivated by our findings showing that the classical (linear) eddy-diffusivity assumption, qeddy ¿ ¿T, fails to provide a reasonable approximation for the actual SGS heat flux, q = uT - uT: namely, a priori analysis for air-filled Rayleigh-Bénard convection (RBC) clearly shows a strong misalignment. In the quest for more accurate models, we firstly study and confirm the suitability of the eddy-viscosity assumption for RBC carrying out a posteriori tests for different models at very low Prandtl numbers (liquid sodium, Pr = 0.005) where no heat flux SGS activity is expected. Then, different (nonlinear) tensor-diffusivity SGS heat flux models are studied a priori using DNS data of air-filled (Pr = 0.7) RBC at Rayleigh numbers up to 1011. Apart from having good alignment trends with the actual SGS heat flux, we also restrict ourselves to models that are numerically stable per se and have the proper cubic near-wall behavior. This analysis leads to a new family of SGS heat flux models based on the symmetric positive semi-definite tensor GGT where G = ¿u, i.e. q ¿ GGT¿T, and the invariants of the GGT tensor, F.X.T. and F.D. are supported by the Ministerio de Economía y Competitividad, Spain (ENE2017-88697-R). F.X.T. and C.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722). F.X.T. was financially supported by a Ramón y Cajal post-doctoral contract (RYC-2012-11996). F.X.T. and A.G. are supported by the Research project 20-02-01 of the Department of the Moscow Center for Fundamental and Applied Mathematics at the Keldysh Insti-tute of Applied Mathematics of RAS. F.D. is supported by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development, and the K1MET center for metallurgical research in Austria (www.k1-met.com). Calculations have been performed on the MareNostrum 4 supercomputer at the BSC (PRACE 15th Call, Ref. 2016163972, “Exploring new fron-tiers in Rayleigh-Bénard convection”; and RES project FI-2019-1-0040 “Exploring nonlinear subgrid-scale heat flux models for buoyancy driven flows”). Preliminary simulations were carried out using computational resources of MCC NRC “Kurchatov Institute”, http://compu ting.nrcki .ru/. The authors thankfully acknowl-edge these institutions, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Towards Real-Time CFD Simulation of Indoor Environment

  • Morozova, Nina
  • Capdevila Paramio, Roser
  • Trias Miquel, Francesc Xavier
  • Oliva Llena, Asensio
Growing computational power and improved numerical algorithms make Computational Fluid Dynamics (CFD) an attractive tool for simulations of indoor environment. In this study di¿erent turbulent models and discretization approaches are investigated on set of di¿erent mesh resolutions in order to choose the CFD technique that suits best for indoor environmental simulations. The investigated con¿guration is the tall deferentially-heated cavity with height aspect ratio of 3.84, this con¿guration resembles a strati¿ed indoor environment, such as a building atrium. The relative error of global air¿ow quantities is compared against computational time for di¿erent CFD approaches. LES simulations together with staggered discretization show the best overall performance in terms of computational speed and accuracy ratio. Furthermore the capability of CFD to perform real-time and even faster than real-time simulations is studied in paradigm of applying it for indoor environmental design and control systems., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Unstructured Level-Set Method For Saturated Liquid-Vapor Phase Change

  • Balcázar Arciniega, Néstor
  • Rigola Serrano, Joaquim
  • Oliva Llena, Asensio
A novel conservative level-set method for saturated liquid-vapor phase change on unstruc-tured meshes is introduced. Transport equations are discretized by the finite-volume method on col-located unstructured grids. Mass transfer promoted by thermal phase change is computed using theenergy jump condition at the interface, as a function of the temperature gradient. The fractional-stepprojection method is used for solving the pressure-velocity coupling, convective terms are discretized byunstructured flux-limiter schemes, central difference scheme is used for discretization of diffusive terms.Verification and validation cases have been undertaken to prove the accuracy and robustness of the nu-merical methods, including simulation of the Stefan problem, and film boiling on a cylindrical surface.Excellent agreement between numerical solutions against analytical solution and empirical correlationsfrom the literature is reported., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical Analysis of Viscoelastic Fluid Injection Processes

  • Amani, Ahmad
  • Schillaci, Eugenio
  • Kizildag, Deniz
  • Pérez Segarra, Carlos David
In this work, a numerical framework aimed at simulating high-viscous and viscoelastic liquid injection processes is presented. The study of fluid injection with viscoelastic properties, such as synthetic polymers, is of great importance in several industrial sectors, such as metallurgy, automotive, food and pharmaceutical products, ink jets and 3D printers. In this work, a Geometrical Volume-of-Fluid (VOF) method is used to represent the interface, while finite-volume discretizations of Navier-Stokes equations on collocated unstructured meshes are solved through a fractional step method. Viscoelastic constitutive models are used to resolve the non-Newtonian behaviours. The employed implementations allow integrating different types of constitutive equations and stabilization approaches. The test case proposed in the current work consist of the simulation of the discharge of a polymeric jet from an upper nozzle into an air-containing cavity with solid bottom. The behavior of the fluids under analysis is validated by observing the onset of fluid-buckling s tructures. This phenomenon consists in the appearance of toroidal oscillation (as coiling and folding patterns) after the jet hits the solid surface and begins to accumulate. First, low-Reynolds number (Re<1.0) Newtonian Jets are analyzed, with the objective of validating the appearance of buckling as a function of Re number, and comparing the results with reference works. Finally, the potentialities of the proposed numerical methods are shown by simulating buckling phenomena in viscoelastic Jets described with the Oldroyd-B constitutive model., This work was developed in the context of a research project (BASE3D 001-P-001646) co-financed by the European Union Regional Development Fund within the framework of the ERDF Operational Program of Catalonia 2014-2020 with a grant of 50% of total cost eligible. The work has also been financially supported by a competitive R+D project (ENE2017-88697-R) of the Spanish Research Agency. The author E.Schillaci acknowledges the financial support of the Programa Torres Quevedo (PTQ2018- 010060)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Assessment and comparison of a recent kinematic sensitive subgrid length scale in Hybrid RANS-LES

  • Pont Vilchez, Arnau
  • Trias Miquel, Francesc Xavier
  • Revell, Alistair
  • Oliva Llena, Asensio
A recent kinematic sensitive subgrid length scale, Δlsq, initially developed for LES applications, is now considered for DES. Even though it is presented as a subgrid length scale, instead of a grey area mitigation (GAM) technique, this initial study shows how it could also be a good and natural approach for addressing this well-known DES shortcoming. In this paper, the Δlsq has been compared with a well-known kinematic sensitive length scale, Δ~ω. It includes a mesh resilience and a shear layer delay study with a Decaying Homogeneous Isotropic Turbulence configuration and two Backward Facing Step configurations, respectively. Encouraging results have been obtained, indicating Δlsq as a subgrid length scale to be considered., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Symmetry-preserving discretization of Navier-Stokes on unstructured grids: collocated vs staggered

  • Trias Miquel, Francesc Xavier
  • Valle Marchante, Nicolás
  • Gorobets, Andrei
  • Oliva Llena, Asensio
The essence of turbulence are the smallest scales of motion. They result from a subtle balance between convective transport and diffusive dissipation. Mathematically, these terms are governed by two differential operators differing in symmetry: the convective operator is skew-symmetric, whereas the diffusive is symmetric and positive-definite. On the other hand, accuracy and stability need to be reconciled for numerical simulations of turbulent flows around complex configurations. With this in mind, a fully-conservative discretization method for general unstructured grids was proposed [Trias et al., J.Comp.Phys. 258, 246-267, 2014]: it exactly preserves the symmetries of the underlying differential operators on a collocated mesh. However, any pressure-correction method on collocated grids suffer from the same drawbacks: the cell-centered velocity field is not exactly incompressible and some artificial dissipation is inevitable introduced. On the other hand, for staggered velocity fields, the projection onto a divergence-free space is a well-posed problem: given a velocity field, it can be uniquely decomposed into a solenoidal vector and the gradient of a scalar (pressure) field. This can be easily done without introducing any dissipation as it should be from a physical point-of-view. In this work, we explore the possibility to build up staggered formulations based on collocated discrete operators., F.X.T., N.V. and A.O. have been financially supported by the Ministerio de Economía y Competitividad, Spain, ANUMESOL project (ENE2017-88697-R). F.X.T. and A.O. are supported by the Generalitat de Catalunya RIS3CAT-FEDER, FusionCAT project (001-P-001722). N.V. was supported by an FI AGAUR-Generalitat de Catalunya fellowship (2017FI B 00616). Calculations were performed on the IBM MareNostrum 4 supercomputer at the BSC. The authors thankfully acknowledge these institutions., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Building a proper tensor-diffusivity model for large-eddy simulation of buoyancy-driven flows

  • Trias Miquel, Francesc Xavier
  • Dabbagh, Firas
  • Gorobets, Andrei
  • Oliva Llena, Asensio
In this work, we plan to shed light on the following research question: can we ¿nd a nonlinear tensorial subgrid-scale (SGS) heat ¿ux model with good physical and numerical properties, such that we can obtain satisfactory predictions for buoyancy driven turbulent ¿ows? This is motivated by our recent ¿ndings showing that the classical (linear) eddy-di¿usivity assumption, qeddy ¿¿ T, fails to provide a reasonable approximation for the SGS heat ¿ux, q = uT - uT. This has been shown in our recent work [Dabbagh et al., Phys. Fluids 29, 105103 (2017)] where SGS features have been studied a priori for a Rayleigh-Bénard convection (RBC). We have also concluded that nonlinear (or tensorial) models can give good approximations of the actual SGS heat ¿ux. The nonlinear Leonard model, qnl ¿¿u¿T, is an example thereof. However, this model is unstable and therefore it cannot be used as standalone SGS heat ¿ux model. Apart from being numerically stable we also want to have the proper cubic near-wall behavior. Corrections in this regard will be presented together with a priori/posteriori studies of nonlinear SGS heat ¿ux models for RBC. Results from LES simulations will be compared with the DNS results obtained in the on-going PRACE project “Exploring new frontiers in Rayleigh-Bénard convection”., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Paving the (right) way for DNS and LES on unstructured grids: (fully) conservative collocated/staggered discretizations

  • Trias Miquel, Francesc Xavier
  • Gorobets, Andrei
  • Oliva Llena, Asensio
The essence of turbulence are the smallest scales of motion. They result from a subtle balance between convective transport and diffusive dissipation. Mathematically, these terms are governed by two differential operators differing in symmetry: the convective operator is skew-symmetric whereas the diffusive is symmetric and positive-definite. On the other hand, accuracy and stability need to be reconciled for simulations of turbulent flows in complex geometries. With this in mind, a fully-conservative discretization method for general unstructured grids was proposed in Ref. [1]: it exactly preserves the symmetries of the underlying differential operators on collocated grids. Hence, unlike other formulations, the discrete convective operator transports energy from a resolved scale of motion to other resolved scales without dissipating energy, as it should do from a physical point-of-view. Therefore, we think that apart from being a right approach for large-scale DNSs of turbulence, it also forms a solid basis for testing subgrid scale LES models. In this work, we will explore the possibility to build up staggered formulations based on the set of discrete operators defined for collocated meshes., F.X.T. and A.O. are financially supported by the Ministerio de Economía y Competitividad, Spain (ENE2017-88697-R). F.X.T. was supported by a Ramón y Cajal contract (RYC-2012-11996). Simulations were carried out on the MareNostrum 4 supercomputer at the BSC. The authors thankfully acknowledge these institutions., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Tetrahedral adaptive mesh refinement for two-phase flows using conservative level-set method

  • Antepara Zambrano, Óscar
  • Balcázar Arciniega, Néstor
  • Oliva Llena, Asensio
In this article, we describe a parallel adaptive mesh refinement strategy for two-phase flows using tetrahedral meshes. The proposed methodology consists of combining a conservative level-set method with tetrahedral adaptive meshes within a finite volume framework. Our adaptive algorithm applies a cell-based refinement technique and adapts the mesh according to physics-based refinement criteria defined by the two-phase application. The new adapted tetrahedral mesh is obtained from mesh manipulations of an input mesh: operations of refinement and coarsening until a maximum level of refinement is achieved. For the refinement method of tetrahedral elements, geometrical characteristics are taking into consideration to preserve the shape quality of the subdivided elements. The present method is used for the simulation of two-phase flows, with surface tension, to show the capability and accuracy of 3D adapted tetrahedral grids to bring new numerical research in this context. Finally, the applicability of this approach is shown in the study of the gravity-driven motion of a single bubble/droplet in a quiescent viscous liquid on regular and complex domains., This work has been financially supported by the Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación, Spain (ENE2017-88697-R), and by Termo Fluids S.L. Oscar Antepara acknowledges financial support in form of a doctoral scholarship DI-14-06886 of the Ministerio de Economía y Competitividad and 2015DI-68 of the Secretaria d’ Universitats i Recerca del Departament d’Economia i Coneixement de la Generalitat de Catalunya, Spain. Néstor Balcázar acknowledges financial support of the Programa Torres Quevedo, Ministerio de Economía y Competitividad, Secretaría de Estado de Investigación, Desarrollo e Innovación (PTQ-14-07186), Spain. Three-dimensional simulations were carried out using computer time provided by PRACE 14th Call (Project 2016153612) and RES project(FI-2018-1-0025) through the MareNostrum IV supercomputer based in Barcelona, Spain. We acknowledge Santander Supercomputacion support group at the University of Cantabria who provided access to the supercomputer Altamira Supercomputer at the Institute of Physics of Cantabria (IFCA-CSIC), member of the Spanish Supercomputing Network, for performing simulations/analyses (RES project FI-2018-3-0037)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Symmetry-Preserving Discretizations In Unstructured Staggered Meshes

  • Valle Marchante, Nicolás
  • Trias Miquel, Francesc Xavier
  • Verstappen, R.W.C.P.
The adoption of symmetry-preserving discretizations is presented in terms of the collocated, unstructured meshes customary of commercial codes. By adopting an algebraic approach, a discretization of the convective terms that reduces to the well know staggered method of Harlow and Welch is presented. The scheme properties are presented along with benchmark simulations concerning turbulent flows, achieving exact conservation of momentum and kinetic energy., Peer Reviewed, Postprint (published version)