Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Synergistic enhancement of Bi2Te3/Sb2Te3-PMMA thermoelectric generators via dithiol-assisted conductivity and FEM-based geometry optimization

  • Hamawandi, Bejan
  • Serrano-Claumarchirant, José F.
  • Ergul, Adem B.
  • Pudzs, Kaspars
  • Pudza, Inga
  • Parsa, Parva
  • Kirsanli, Metehan
  • Bitmets, Oskars
  • Toprak, Muhammet S.
[EN] In recent decades, thermoelectric (TE) materials have proven to be a complementary source of renewable energy, as they can directly convert waste heat into electrical energy. Energy-efficient, reliable, and scalable synthetic routes for the fabrication of TE materials and their processing into functional devices via low-energy and low-waste routes are necessary for the broader adoption of these materials in various applications. In this work, we report the formulation of hybrid thermoelectric (hTE) inks based on nanostructured Sb2Te3 and Bi2Te3, using PMMA as the polymer matrix and hexanedithiol (HDT) as the binder. Percolation studies were conducted to determine the optimal film composition, with an 80% nanoparticle content yielding the highest TE performance. Finite element modelling (FEM) was employed to optimize the device geometry, including the cross-sectional area ratio of p-and n-type legs, to maximize power output. Based on these results, a flexible hTEG was fabricated using the optimized ink composition. The device exhibited an output power of 950 nW and a Power output Density (PoD) of 40.37 nW cm-2 under a 30 K temperature gradient, significantly outperforming previously reported polymer-based flexible hTEGs incorporating chalcogenides. This study presents a sustainable and effective strategy for developing high-performance hybrid thermoelectric devices through ink formulation, composition optimization, and simulation-guided device design., B.H. acknowledges the support of the Latvian Council of Science project No.1.1.1.9/LZP/1/24/043.M.S.T. and J.F.S-C. acknowledges funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 863222, and Olle Engkvist Foundation (SOEB, 226-0113). We acknowledge DESY (Hamburg, Germany), a member of the Helmholtz Association HGF, for providing experimental facilities. The experiments at the DESY PETRA III synchrotron were performed within proposal No I-20220381 EC. M.S.T. acknowledges the financial support from Olle Engkvist Foundation (SOEB, 190-0315) for establishing MW synthesis facilities. O.B and K.P. thank the support of the Latvian Council of Science, grant number lzp-2023/1-0456. J.F.S-C. acknowledges the support of the Juan de la Cierva fellowship (JDC2023-051223-I) .
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Power factor improvement in a solid-liquid thermoelectric system formed by Sb:SnO2 in contact with a chromium complex solution

  • Castro-Ruiz, S.
  • Márquez-García, L.
  • Solis-de la Fuente, M.
  • Beltrán-Pitarch, Braulio
  • Mota-Babiloni, A.
  • Vidan, Francisco
  • Íñigo-Rabinal, P.
  • Guisado‐Barrios, Gregorio
  • García-Cañadas, Jorge
This article is part of the themed collection: Recent Open Access Articles, Thermoelectric (TE) materials can convert heat into electricity. Good TE materials should have high power factors (PF) and low thermal conductivities. PF = S2σ is governed by the Seebeck coefficient S and the electrical conductivity σ. Most recent improvements in TE materials performance have been achieved by the reduction of the thermal conductivity, and strategies to improve the PF have been minor. Recently, an innovative concept to significantly increase the PF, based on the combination of a porous TE solid with an electrolyte, has been reported. Here, we make use of this new approach but using an electroactive salt (redox molecule) solution as electrolyte, rather than the non-electroactive electrolytes and ionic liquids previously employed. A system formed by a nanostructured and porous Sb:SnO2 film in contact with Cr(III) acetylacetonate dissolved in 3-methoxypropionitrile was prepared. Using this electrolyte, an average PF enhancement of 3.4 times was achieved, due to an average decrease of 23.2% and 82.8% in the absolute value of the Seebeck coefficient and the electrical resistivity of the solid, respectively. An impedance spectroscopy analysis, after checking by scanning electron microscopy and energy-dispersive X-ray spectroscopy that no changes take place in the Sb:SnO2 film due to the presence of electrolytes, revealed that the improvements come from the donation of electrons from the electrolyte to the solid, which increases its electrical conductivity and the usual drop in the Seebeck coefficient. The remarkable PF improvement obtained is among the highest reported and opens a new way of significantly enhancing this parameter., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement no. 863222 (UncorrelaTEd project). We also acknowledge funding support from PID2021-122900NB-I00 financed by MICIN/AEI/10.13039/501100011033/FEDER “Una manera de hacer Europa”. G. G.-B gratefully acknowledges (RYC2019-026693-I/AEI/10.13039/501100011033) “El Fondo Social Europeo invierte en tu futuro’ and Gobierno de Aragón/FEDER, UE (GA/FEDER, Reactividad y catálisis en química inorgánica, Group E50_20D)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Power factor improvement in a solid–liquid thermoelectric system formed by Sb:SnO<sub>2</sub> in contact with a chromium complex solution

  • Castro-Ruiz, S.
  • Márquez-García, L.
  • Solis-de la Fuente, M.
  • Beltrán-Pitarch, B.
  • Mota-Babiloni, A.
  • Vidan, F.
  • Íñigo-Rabinal, P.
  • Guisado-Barrios, G.
  • García-Cañadas, J.
Thermoelectric (TE) materials can convert heat into electricity. Good TE materials should have high power factors (PF) and low thermal conductivities. PF = S2σ is governed by the Seebeck coefficient S and the electrical conductivity σ. Most recent improvements in TE materials performance have been achieved by the reduction of the thermal conductivity, and strategies to improve the PF have been minor. Recently, an innovative concept to significantly increase the PF, based on the combination of a porous TE solid with an electrolyte, has been reported. Here, we make use of this new approach but using an electroactive salt (redox molecule) solution as electrolyte, rather than the non-electroactive electrolytes and ionic liquids previously employed. A system formed by a nanostructured and porous Sb:SnO2 film in contact with Cr(III) acetylacetonate dissolved in 3-methoxypropionitrile was prepared. Using this electrolyte, an average PF enhancement of 3.4 times was achieved, due to an average decrease of 23.2% and 82.8% in the absolute value of the Seebeck coefficient and the electrical resistivity of the solid, respectively. An impedance spectroscopy analysis, after checking by scanning electron microscopy and energy-dispersive X-ray spectroscopy that no changes take place in the Sb:SnO2 film due to the presence of electrolytes, revealed that the improvements come from the donation of electrons from the electrolyte to the solid, which increases its electrical conductivity and the usual drop in the Seebeck coefficient. The remarkable PF improvement obtained is among the highest reported and opens a new way of significantly enhancing this parameter.