Pasar al contenido principal

DISPOSITIVOS OPTICOS EN EL ULTRAVIOLETA LEJANO PARA INSTRUMENTACION ESPACIAL

AYA2013-42590-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Narrowband filters for the FUV range

  • Rodríguez de Marcos, Luís
  • Larruquert, Juan Ignacio
  • Méndez, José Antonio
  • Aznárez, José Antonio
  • Fu, Liping
10 págs.; 6 figs.; 4 tabs., We address the design, fabrication, and characterization of transmittance filters for the Ionosphere Photometer instrument (IP), developed by the Center for Space Science and Applied Research (CSSAR). IP, a payload of Feng-Yun 3D meteorological satellite, to be launched on 2016, is aimed to perform photometry measurements of Earth¿s ionosphere by the analysis of the OI (135.6 nm) spectral line and N2 Lyman-Birge-Hopfield (LBH, 140-180 nm) band, both of them in the far ultraviolet (FUV) range. The most convenient procedure to isolate a spectral band is the use of tunable transmittance filters. In many applications the intensity of the ultraviolet, visible and infrared background is higher than the intensity of the target FUV lines; therefore one of the most important requirements for transmittance filters is to reject (by reflecting and/or by absorbing) as efficiently as possible the visible and close ranges. In the FUV range, (Al/MgF2)n transmittance filters are the most common, and they are suitable to reject the visible and adjacent ranges. These materials present unique properties in this range: MgF2 is transparent down to ~115 nm and Al has a very low refractive index in the FUV that contrasts well with MgF2. Narrowband tunable filters with very low transmittance at long wavelengths are achievable. The main data on the preparation and characterization of IP filters by Grupo de Óptica de Láminas Delgadas (GOLD) is detailed. In this proceeding we present (Al/MgF2)3 filters peaked at either 135.6 nm or at the center of the LBH band (~160 nm). Filters were characterized in the 125-800 nm range (143-800 nm range for the LBH filter). After some storage in a desiccator, both coatings kept a transmittance of ~0.14 at their target wavelengths, with visible-topeak transmittance ratios of 1.2·10-4 (OI filter) and 1.3·10-4 (LBH filter). One filter tuned at each target wavelength was exposed to ~300 Gy 60Co gamma dose, with no significant transmittance change. Keywords: Coatings, Far Ultraviolet, Atmosphere Physics, Transmittance Filters, Space Optics, This research was partly supported by the National Programme for Research, Subdirección General de Proyectos de Investigación, Ministerio de Ciencia e Innovación, project number AYA2010-22032 and AYA2013- 42590-P. The authors are gratefully acknowledged to Pedro Valdivieso (Instalación de irradiación Náyade, CIEMAT)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Transmittance and optical constants of ca films in the 4-1000 eV spectral range

  • Rodríguez de Marcos, Luís
  • Larruquert, Juan Ignacio
  • Vidal Dasilva, Manuela
  • Aznárez, José Antonio
  • García-Cortés, Sergio
  • Méndez, José Antonio
  • Poletto, L.
  • Frassetto, F.
  • Malvezzi, A. Marco
  • Bajoni, D.
  • Giglia, A.
  • Mahne, N.
  • Nannarone, S.
8 págs.; 8 figs.; OCIS codes: (260.7200) Ultraviolet, extreme; (120.4530) Optical constants; (350.2450) Filters, absorption; (230.4170) Multilayers; (310.6860) Thin films, optical properties., © 2015 Optical Society of America. The low expected absorption of Ca in the extreme ultraviolet (EUV) makes it an attractive material for multilayers and filters because most materials in nature strongly absorb the EUV. Few optical constant data had been reported for Ca. In this research, Ca films of various thicknesses were deposited on gridsupported C films and their transmittance measured in situ from the visible to the soft x-rays. The measurement range contains M2,3 and L2,3 absorption edges. Transmittance measurements were used to obtain the Ca extinction coefficient k. A minimum k of 0.017 was obtained at ∼23 eV, which makes Ca a promising low-absorption material for EUV coatings. A second spectral range of interest for its low absorption is below the Ca L3 edge at ∼343 eV. Measured k data and extrapolations were used to calculate the refractive index n using Kramers.Kronig relations. This is the first self-consistent data set on Ca covering a wide spectral range including the EUV., We acknowledge support by the European Community—Research Infrastructure Action under the FP6 “Structuring the European Research Area” Programme (through the Integrated Infrastructure Initiative “Integrating Activity on Synchrotron and Free Electron Laser Science”) through proposal number Ref. 2007655. This work was also supported by the National Programme for Space Research, Subdirección General de Proyectos de Investigación, Ministerio de Ciencia y Tecnología, project numbers AYA2010-22032 and AYA2013-42590-P. L. Rodrí- guez-de Marcos and S. García-Cortés are thankful to Consejo Superior de Investigaciones Científicas (CSIC) for funding under the Programa JAE, partially supported by the European Social Fund. M. Vidal-Dasilva acknowledges financial support from an FPI fellowship number BES-2006-14047, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Mirror coating technology advances

  • Larruquert, Juan Ignacio
Presentación con 24 diapositivas; NASA, Goddard Space Flight Center Greenbelt, MD (USA), June 24-26, 2015; http://asd.gsfc.nasa.gov/conferences/uvvis/flagship/, Spanish Programa Nacional de Astronomía y Astrofísica AYA2013-42590-P, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Analytic optical-constant model derived from Tauc-Lorentz and Urbach tail

  • Rodríguez de Marcos, Luís
  • Larruquert, Juan Ignacio
Tauc-Lorentz model is commonly used to describe the dielectric constant of amorphous semiconductors as a function of few parameters. However, this model is not fully analytic and presents other mathematical shortcomings. A modified self-consistent model based on the integration of [E'-(E + ia)]-1 functions using Tauc-Lorentz's ε expression as a weight function is presented. This new model is analytic and meets all other mathematical requirements of optical constants. The main difference with TL model stands at photon energies close to or smaller than the bandgap energy. The new model has been satisfactorily tested on SiC optical constants. Additionally, an analytic extension of the new model has been also developed to include the Urbach tail. The complete model has been tested with SiN optical constants, and it enables to extend the optical-constant characterization of materials down to zero energy., Spanish Programa Estatal de Investigación Científica y Técnica de Excelencia, Secretaría de Estado de Investigación, Desarrollo e Innovación, project number AYA2013-42590-P., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Self-consistent optical constants of SiO2 and Ta2O5 films

  • Rodríguez de Marcos, Luís
  • Larruquert, Juan Ignacio
  • Méndez, José Antonio
  • Aznárez, José Antonio
16 págs.; 8 figs.; 1 tab. ; OCIS codes: (120.4530) Optical constants; (310.6860) Thin films, optical properties; (230.4170) Multilayers; (260.7210) Ultraviolet, vacuum; (260.7190) Ultraviolet; (260.7200) Ultraviolet, extreme, Self-consistent optical constants of SiO and TaO films have been obtained for their relevance in optical coatings from the near ultraviolet to the near infrared spectral ranges, where they are transparent and have a high refractive index contrast. Particular attention has been paid to wavelengths close to and shorter than each material cutoff. The far and the extreme ultraviolet ranges are also covered here, where few (SiO) or almost no optical constant data (TaO) were available for films of these materials. This work is aimed at filling the lack of self-consistent sets of optical constants with data in a very broad spectral range, which can be widely applied in multilayer design for the everyday use of these materials in multilayer coatings. Oxide films were deposited by reactive electron-beam evaporation onto various sorts of substrates at 573 K. Transmittance, reflectance, and ellipsometry measurements were performed for each oxide in spectral intervals jointly covering from the extreme ultraviolet to the near infrared; starting with these measurements along with extrapolations, an iterative and double Kramers-Kronig analysis procedure has been followed to obtain a self-consistent set of optical constants per material. With the final data sets, we have satisfactorily reproduced the experimental measurements. Global data selfconsistency was successfully evaluated through sum rules, and local consistency at each photon energy range was also evaluated through a novel sum-rule method which involves window functions. © 2016 Optical Society of America, Spanish Programa Estatal de Investigación Científica y Técnica de Excelencia, Secretaría de Estado de Investigación, Desarrollo e Innovación (AYA2013-42590-P)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning sum rules with window functions for optical constant evaluation

  • Rodríguez de Marcos, Luís
  • Méndez, José Antonio
  • Larruquert, Juan Ignacio
10 págs.; 7 figs. ; 2 tabs., Sum rules are a useful tool to evaluate the global consistency of a set of optical constants. We present a procedure to spectrally tune sum rules to evaluate the local consistency of optical constants. It enables enhancing the weight of a desired spectral range within the sum-rule integral. The procedure consists in multiplying the complex refractive index with an adapted function, which is named window function. Window functions are constructed through integration of Lorentz oscillators. The asymptotic decay of these window functions enables the derivation of a multiplicity of sum rules akin to the inertial sum rule, along with one modified version of f-sum rule. This multiplicity of sum rules combined with the free selection of the photon energy range provides a double way to tune the spectral contribution within the sum rule. Window functions were applied to reported data of SrF and of Al films in order to check data consistency over the spectrum. The use of window functions shows that the optical constants of SrF are consistent in a broad spectrum. Regarding Al, some spectral ranges are seen to present a lower consistency, even though the standard sum rules with no window function did not detect inconsistencies. Hence window functions are expected to be a helpful tool to evaluate the local consistency of optical constants. 2016 IOP Publishing, We acknowledge support by Spanish Programa Estatal de Investigación Científica y Técnica de Excelencia, Secretaría de Estado de Investigación, Desarrollo e Innovación, project number AYA2013-42590-P., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Advances in far-ultraviolet reflective and transmissive coatings for space applications

  • Rodríguez de Marcos, Luís
  • Aznárez, José Antonio
  • Méndez, José Antonio
  • Larruquert, Juan Ignacio
  • Vidal Dasilva, Manuela
  • Malvezzi, A. Marco
  • Giglia, Angelo
  • Capobianco, Gerardo
  • Fineschi,Silvano
  • Nannarone, S.
10 pags., 8 figs., Conference Volume 9912. Advances in Optical and Mechanical Technologies for Telescopes and Instrumentation II, Edinburgh, United Kingdom, June 26, 2016, Conferencia programada dentro de Advances in Optical and Mechanical Technologies for Telescopes and Instrumentation, part of SPIE Astronomical Telescopes + Instrumentation., Exploitation of far ultraviolet (FUV, 100-200 nm) observations extends to most areas of modern astronomy, from detailed observations of Solar System objects, the interstellar medium, exoplanets, stars and galaxies, to studies of crucial cosmological relevance. Despite several developments in recent decades, yet many observations are not possible due to technical limitations, of which one of the most important is the lack of optical coatings with high throughput. Development and optimization of such efficient FUV coatings have been identified in several roadmap reports as a key goal for future missions. The success of this development will ultimately improve the performance of nowadays feasible optical instruments and will enable new scientific imaging capabilities. GOLD’s research is devoted to developing novel coatings with enhanced performance for space optics. Several deposition systems are available for the deposition of multilayer coatings. A deposition system was developed to deposit FUV coatings to satisfy space requirements. It consists of a 75-cm-diameter deposition chamber pumped with a cryo-pump and placed in an ISO-6 clean room. This chamber is available for deposition by evaporation of top-requirement coatings such as Al/ MgF2 mirrors or (Al/MgF2)n multilayer coatings for transmittance filters. A plan to add an Ion-Beam-Sputtering system in this chamber is under way. In this and other chambers at GOLD the following FUV coatings can be prepared: Transmittance filters based on (Al/MgF2)n multilayer coatings. These filters can be designed to have a peak at the FUV spectral line or band of interest and a high peak-to-visible transmittance ratio. Filters can be designed with a peak transmittance at a wavelength as short as 120 nm and with a transmittance in the visible smaller than 10-5. Narrowband reflective coatings peaked close to H Lyman β (102.6 nm) with a reflectance at H Lyman α (121.6 nm) two orders of magnitude below the one at 102.6 nm. Other potential spectral lines at which these coatings could be peaked are the OVI doublet (103.2, 103.8 nm). Narrowband reflective mirrors based on (MgF2/LaF3)n multilayers peaked at a wavelength as short as 120 nm. Target wavelengths include lines of high interest for space observations, such as H Lyman α (121.6 nm), OI (130.4 and 135.6 nm), CIV (154.8, 155.1 nm), among others. Coating-based linear polarizers tuned at H Lyman α (121.6 nm) both based on reflectance or on transmittance. Reflective polarizers present a high efficiency. Transmissive polarizers have a more modest peak performance compared to reflective polarizers; however, they involve spectral filtering properties to reject the long FUV and even more the near UV to the IR, which turn them competitive compared to reflective polarizers. In this communication we present a summary of our research on the above FUV coatings developed at GOLD. © (2016) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE)., We acknowledge support by Spanish Programa Estatal de Investigación Científica y Técnica de Excelencia, Secretaría de Estado de Investigación, Desarrollo e Innovación, project number AYA2013-42590-P., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polarizers tuned at key far-UV spectral lines for space instrumentation

  • Larruquert, Juan Ignacio
  • Malvezzi, A. Marco
  • Rodríguez de Marcos, Luís
  • Giglia, Angelo
  • Gutiérrez-Luna, Nuria
  • Espinosa-Yáñez, Lucía
  • Honrado-Benítez, Carlos
  • Aznárez, José Antonio
  • Massone, Giuseppe
  • Capobianco, Gerardo
  • Feneschi, Silvano
  • Nannarone, S.
8 pags., 4 figs., 2 tabs. -- EUV and X-ray Optics: Synergy between Laboratory and Space V. -- SPIE Optics + Optoelectronics, 2017, Prague, Czech Republic, Polarimetry is a valuable technique to help us understand the role played by the magnetic field of the coronal plasma in the energy transfer processes from the inner parts of the Sun to the outer space. Polarimetry in the far ultraviolet (FUV: 100-200 nm), which must be performed from space due to absorption in terrestrial atmosphere, supplies fundamental data of processes that are governed by the Doppler and Hanle effects on resonantly scattered line-emission. To observe these processes there are various key spectral lines in the FUV, from which H I Lyman ¿ (121.6 nm) is the strongest one. Hence some solar physics missions that have been proposed or are under development plan to perform polarimetry at 121.6 nm, like the suborbital missions CLASP I (2015) and CLASP II (2018), and the proposed solar missions SolmeX and COMPASS and stellar mission Arago. Therefore, the development of efficient FUV linear polarizers may benefit these and other possible future missions. C IV (155 nm) and Mg II (280 nm) are other spectral lines relevant for studies of solar and stellar magnetized atmospheres. High performance polarizers can be obtained with optimized coatings. Interference coatings can tune polarizers at the spectral line(s) of interest for solar and stellar physics. Polarizing beamsplitters consist in polarizers that separate one polarization component by reflection and the other by transmission, which enables observing the two polarization components simultaneously with a single polarizer. They involve the benefit of a higher efficiency in collection of polarization data due to the use of a single polarizer for the two polarization components and they may also facilitate a simplified design for a space polarimeter. We present results on polarizing beamsplitters tuned either at 121.6 nm or at the pair of 155 and 280 nm spectral lines., We acknowledge support by the European Community–Research Infrastructure Action under the FP6 ‘Structuring the European Research Area’ Programme (through the Integrated Infrastructure Initiative ‘Integrating Activity on Synchrotron and Free Electron Laser Science’); measurements were performed under ELETTRA proposal numbers 20115134, 20120059, 20125119, 20130201, 20135237, 20140171, 20150344, and 2015497. This work was also supported by the National Programme for Research, Subdirección General de Proyectos de Investigación, Ministerio de Ciencia e Innovación, project numbers AYA2013-42590-P and ESP2016-76591-P. We also acknowledge support by the Italian Ministry of University and Research (MIUR) under the Programmi di Ricerca Scientifica di Rilevante Interesse Nazionale—Bando 2012., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Self-consistent optical constants of MgF2,LaF3, and CeF3 films

  • Rodríguez de Marcos, Luís
  • Larruquert, Juan Ignacio
  • Méndez, José Antonio
  • Aznárez, José Antonio
18 pags., 11 figs., 3 tabs., Various fluorides are materials in nature that extend their transparency range to the shortest wavelengths in the far ultraviolet (FUV, 100nm<¿<200 nm). These are relevant materials to prepare multilayer coatings in the FUV for demanding applications such as space instrumentation for astrophysics, solar physics and atmosphere physics, as well as free electron lasers, plasma diagnostics, synchrotron radiation, lithography, spectroscopy, etc. Multilayer design requires the optical constants of the coating materials. Multilayers optimally alternate two transparent materials with contrasting refractive indices. The optical constants of a low-index material, MgF2, and of two high-index materials, LaF3 and CeF3, have been determined in a wide spectral range and are presented here. Thin films of MgF2, LaF3, and CeF3 were deposited by boat evaporation onto substrates at 523 K. Transmittance, reflectance, and ellipsometry measurements were performed in ranges jointly covering the 30- 950-nm spectral range. This range was extended with literature data and extrapolations to obtain self-consistent optical constants using the Kramers-Kronig (KK) analysis. An iterative, double KK analysis procedure (successive reflectance-phase and k-n KK analyses) was carried out to obtain a self-consistent set of optical constants per material. With the final data sets, the experimental measurements were satisfactorily reproduced. Global self-consistency of the data sets was successfully evaluated through sum rules; additionally, local selfconsistency at each photon energy range was also evaluated through a novel sum-rule method which involves window functions. The new sets of optical constant extend the data availability mainly to the FUV and beyond, particularly for CeF3, where few data had been reported., Spanish Programa Estatal de Investigación Científica y Técnica de Excelencia, Secretaría de Estado de Investigación, Desarrollo e Innovación (AYA2013-42590-P and ESP2016-76591-P)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimization of MgF2-deposition temperature for far UV Al mirrors

  • Rodríguez de Marcos, Luís
  • Larruquert, Juan Ignacio
  • Méndez, José Antonio
  • Gutiérrez-Luna, Nuria
  • Espinosa-Yáñez, Lucía
  • Honrado-Benítez, Carlos
  • Chavero Royan, José
  • Perea-Abarca, Belén
10 pags., 6 figs., tab. -- OCIS codes: (230.4040) Mirrors; (310.1515) Protective coatings; (260.7210) Ultraviolet, vacuum; (160.4670) Optical materials; (310.6860) Thin films, optical properties; (120.6085) Space instrumentation., Progress towards far UV (FUV) coatings with enhanced reflectance is invaluable for future space missions, such as LUVOIR. This research starts with the procedure developed to enhance MgF-protected Al reflectance through depositing MgF on a heated aluminized substrate [Quijada et al., Proc. SPIE 8450, 84502H (2012)] and it establishes the optimum deposition temperature of the MgF2 protective film for Al mirrors with a reflectance as high as ∼90% at 121.6 nm. Al films were deposited at room temperature and protected with a MgF2 film deposited at various temperatures ranging from room temperature to 350°C. It has been found that mirror reflectance in the short FUV range continuously increases with MgF deposition temperature up to 250°C, whereas reflectance decreases at temperatures of 300°C and up. The short-FUV reflectance of mirrors deposited at 250°C only slightly decreased over time by less than 1%, compared to a larger decay for standard coatings prepared at room temperature. Al mirrors protected with MgF2 deposited at room temperature that were later annealed displayed a similar reflectance enhancement that mirrors protected at high temperatures. MgF and Al roughness as well as MgF density were analyzed by x-ray grazing incidence reflectometry. A noticeable reduction in both Al and MgF roughness, as well as an increase of MgF2 density, were measured for films deposited at high temperatures. On the other hand, it was found a strong correlation between the protective-layer deposition temperature (or post-deposition annealing temperature) and the pinhole open area in Al films, which could be prevented with a somewhat thicker Al film., Secretaría de Estado de Investigación, Desarrollo e Innovación (AYA2013-42590-P, ESP2016-76591-P)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Lyman-β narrowband coatings with strong Lyman-α rejection

  • Rodríguez de Marcos, Luís
  • Larruquert, Juan Ignacio
  • Méndez, José Antonio
  • Vidal Dasilva, Manuela
  • García-Cortés, Sergio
  • Gutiérrez-Luna, Nuria
  • Espinosa-Yáñez, Lucía
  • Honradobenítez, Carlos
  • Chavero Royan, José
12 pags., 8 figs., 2 tabs., Novel narrowband multilayer coatings efficient at a wavelength as short as 100 mn are presented, which pushes shortwards the existing limit of reported narrowband multilayers. Such limit had been established at ~120 nm, close to the MgF2 cutoff wavelength. The new multilayers combine layers of Al, LiF, and SiC, in an Al/LiF/SiC/LiF multilayer design (four layers, starting with the innermost layer). Among these materials, Al and LiF are deposited by evaporation and SiC by ion-beam-sputtering. In addition to a high, narrow peak close to H Lyman β (102.6 nm), these multilayers simultaneously provide a very small reflectance at H Lyman α (121.6 nm). This combined performance is demanded in space instrumentation for astrophysics and solar physics observations among others, where imaging the sky at the important diagnostic spectral line of Lyman β line requires rejecting the frequently much more intense background at Lyman α line. Such is the case for solar corona observations at Lyman β, which is masked by the strong Lyman α line. The multilayer peak is placed close to another important diagnostic tool: the OVI doublet at 103.2 and 103.8 nm. The target of small reflectance at 121.6 nm was seen to be the most critical. The best strategy in multilayer preparation was to prepare it with such minimum reflectance at slightly shorter wavelengths so that the coating evolved to shift it longwards over time. Multilayers kept a remarkable 102.6 nm/121.6 nm reflectance ratio over time in spite of some performance degradation. Hence, a multilayer coating aged of 4 years kept a reflectance of 43% at 102.6 nm and 0.2% at 121.6 nm., Spanish Programa Estatal de Investigación Científica y Técnica de Excelencia, Secretaría de Estado de Investigación, Desarrollo e Innovación (AYA2013-42590-P, ESP2016-76591-P, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Procedure to convert optical-constant models into analytic

  • Larruquert, Juan Ignacio
  • Rodríguez de Marcos, Luís
8 pags., 3 figs., 2 tabs. -- Corrigendum to Procedure to convert optical-constant models into analytic Thin Solid Films (2018) 52-59, Thin Solid Films, Volume 733, 1 September 2021, Pages 138816. -- http://hdl.handle.net/10261/263138, Several common optical-constant models do not satisfy a necessary requirement: they are not analytic (in the sense of holomorphic). This includes models defined with a piecewise function like Tauc-Lorentz, Cody-Lorentz (CL), and Campi-Coriasso, and models with poles in the upper complex half plane. The consequence of this is an intrinsic inaccuracy. Sellmeier model, even though analytic, involves mostly unnatural divergences. A procedure is presented that turns non-analytic optical models into analytic by using the original model as a weight function in an integral over the spectrum using a small broadening parameter. Specific equations are obtained for the weight function being either the dispersion or the absorption part of the optical constants of the non-analytic model. The resulting optical-constant model can be differentiated to any order. The procedure is applied to turn analytic CL model and to remove the divergences from Sellmeier model. The analyticized CL model is applied to fit boron film optical constants., This work was supported by Spanish Programa Estatal de Investigación Científica y Técnica de Excelencia, Secretaría de Estado de Investigación, Desarrollo e Innovación [grant numbers AYA2013- 42590-P, ESP2016-76591-P].