Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Carbon nanofiber- and alumina-reinforced lithium aluminosilicate for controlled thermal expansion materials

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Garcia-Moreno, Olga
  • Torrecillas, Ramón
  • Garcia-Rocha, Victoria
  • Fernandez, Adolfo
[EN] Materials with a very low or tailored thermal expansion have many applications ranging from cookware to the aerospace industry. Among others, lithium aluminosilicates (LAS) are the most studied family with low and negative thermal expansion coefficients. However, LAS materials are electrical insulators and have poor mechanical properties. Nanocomposites using LAS as a matrix are promising in many applications where special properties are achieved by the addition of one or two more phases. The main scope of this work is to study the sinterability of carbon nanofiber (CNFs)/LAS and CNFs/alumina/LAS nanocomposites, and to adjust the ratio among components for obtaining a near-zero or tailored thermal expansion. Spark plasma sintering of nanocomposites, consisting of commercial CNFs and alumina powders and an ad hoc synthesized beta-eucryptite phase, is proposed as a solution to improving mechanical and electrical properties compared with the LAS ceramics obtained under the same conditions. X-ray diffraction results on phase compositions and microstructure are discussed together with dilatometry data obtained in a wide temperature range (-150 to 450 degrees C). The use of a ceramic LAS phase makes it possible to design a nanocomposite with a very low or tailored thermal expansion coefficient and exceptional electrical and mechanical properties., This work was financially supported by the National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A Borrell thanks the Spanish Ministry of Science and Innovation for her research grant BES2007-15033. O Garcia-Moreno is working for CSIC under a JAE-Doc contract co-funded by the ESF.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of Carbon Nanofibers/ZrO2 Composites Properties with a Zirconia Nanocoating on Carbon Nanofibers by Sol–Gel Method

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Rocha, Victoria G.
  • Torrecillas, Ramon
  • Fernandez, Adolfo
The development of new carbon nanofibers (CNFs)–ceramic nanocomposite materials with excellent mechanical, thermal, and electrical properties is interesting for a wide range of industrial applications. Among the ceramic materials, zirconia stands out for their excellent mechanical properties. The main limitations in the preparation of this kind of nanocomposites are related with the difficulty in obtaining materials with homogeneous distribution of both phases and the dissimilar properties of CNFs and ZrO2 which causes poor interaction between them. CNFs-reinforced zirconia nanocomposites ZrO2/xCNFs (x=1–20 vol%) were prepared by powder mixture and sintered by spark plasma sintering (SPS). ZrO2-reinforced CNFs nanocomposites CNFs/xZrO2 (x=20 vol%) were prepared by powder mixture and a surface coating of CNFs by the wet chemical route with zirconia precursor is proposed as a very effective way to improve the interaction between CNFs and ZrO2. After SPS sintering, an improvement of 50% in fracture strength was found for similar nanocomposite compositions when the surface coating was used. The improved mechanical properties of these nanocomposites are caused by stronger interaction between the CNFs and ZrO2., This work was financially supported by National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her research grant BES2007-15033.