Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Surface coating on carbon nanofibers with alumina precursor by different synthesis routes

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Rocha, V. G.
  • Torrecillas, R.
  • Fernandez, A.
[EN] Alumina-reinforced carbon nanofiber nanocomposites were prepared using different routes; powders mixture, colloidal route and sol-gel process followed by spark plasma sintering (SPS). CNFs/xAl(2)O(3) (x = 10-50 vol.%) were prepared through nanopowders mixing in a high-energy attrition milling. The main limitations in the preparation of this kind of nanocomposites are related to the difficulty in obtaining materials with a homogeneous distribution of both phases and the different chemical nature of CNFs and Al(2)O(3), which causes poor interaction between them. A surface coating of CNFs by wet chemical routes with an alumina precursor is proposed as a very effective way to improve the interaction between CNFs and Al(2)O(3). An improvement of 50% in fracture strength was found for similar nanocomposite compositions when the surface coating was used. The improved mechanical properties of these nanocomposites are caused by stronger interaction between the CNFs and Al(2)O(3). Crown Copyright (C) 2010 Published by Elsevier Ltd. All rights reserved., This work has been carried out with financial support of National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for Ph.D. grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Carbon nanofiber- and alumina-reinforced lithium aluminosilicate for controlled thermal expansion materials

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Garcia-Moreno, Olga
  • Torrecillas, Ramón
  • Garcia-Rocha, Victoria
  • Fernandez, Adolfo
[EN] Materials with a very low or tailored thermal expansion have many applications ranging from cookware to the aerospace industry. Among others, lithium aluminosilicates (LAS) are the most studied family with low and negative thermal expansion coefficients. However, LAS materials are electrical insulators and have poor mechanical properties. Nanocomposites using LAS as a matrix are promising in many applications where special properties are achieved by the addition of one or two more phases. The main scope of this work is to study the sinterability of carbon nanofiber (CNFs)/LAS and CNFs/alumina/LAS nanocomposites, and to adjust the ratio among components for obtaining a near-zero or tailored thermal expansion. Spark plasma sintering of nanocomposites, consisting of commercial CNFs and alumina powders and an ad hoc synthesized beta-eucryptite phase, is proposed as a solution to improving mechanical and electrical properties compared with the LAS ceramics obtained under the same conditions. X-ray diffraction results on phase compositions and microstructure are discussed together with dilatometry data obtained in a wide temperature range (-150 to 450 degrees C). The use of a ceramic LAS phase makes it possible to design a nanocomposite with a very low or tailored thermal expansion coefficient and exceptional electrical and mechanical properties., This work was financially supported by the National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A Borrell thanks the Spanish Ministry of Science and Innovation for her research grant BES2007-15033. O Garcia-Moreno is working for CSIC under a JAE-Doc contract co-funded by the ESF.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Alumina-carbon nanofibers nanocomposites obtained by spark plasma sintering for proton exchange membrane fuel cell bipolar plates

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Torrecillas, Ramón
  • Rocha, Victoria G.
  • Fernández, Adolfo
[EN] There is an increasing demand of multifunctional materials for a wide variety of technological developments. Bipolar plates for proton exchange membrane fuel cells are an example of complex functionality components that must show among other properties high mechanical strength, electrical, and thermal conductivity. The present research explored the possibility of using alumina¿carbon nanofibers (CNFs) nanocomposites for this purpose. In this study, it was studied for the first time the whole range of powder compositions in this system. Homogeneous powders mixtures were prepared and subsequently sintered by spark plasma sintering. The materials obtained were thoroughly characterized and compared in terms of properties required to be used as bipolar plates. The control on material microstructure and composition allows designing materials where mechanical or electrical performances are enhanced. A 50/50¿vol.% alumina¿CNFs composite appears to be a very promising material for this kind of application., This work has been carried out with financial support of National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for Ph.D. grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of CNFs content on the tribological behaviour of spark plasma sintering ceramic-CNFs composites

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Torrecillas, R.
  • Rocha, V. G.
  • Fernandez, A.
  • Bonache Bezares, Victoria
Alumina-carbon nanofibres (CNFs) and silicon carbide-CNFs nanocomposites with different volume fraction of CNFs (0-100vol.%) were obtained by spark plasma sintering. The effect of CNFs content on the tribological behaviour in dry sliding conditions on the ceramic-carbon nanocomposites has been investigated using the ball-on-disk technique against alumina balls. The wear rate of ceramic-CNFs nanocomposites decreases with CNFs increasing content. The friction coefficient of the Al 2O 3/CNFs and SiC/CNFs nanocomposites with high CNFs content was found to be significantly lower compared to monolithic Al 2O 3 and SiC due to the effect of CNFs and unexpectedly slightly lower than CNFs material. The main wear mechanism in the nanocomposite was abrasion of the ceramic and carbon components which act in the interface as a sort of lubricating media. The experimental results demonstrate that the addition of CNFs to the ceramic composites significantly reduces friction coefficient and wear rate, resulting in suitable materials for unlubricated tribological applications. © 2011., This work has been carried out with financial support of National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell acknowledges the Spanish Ministry of Science and Innovation for her FPI Ph.D. grant. We would like to thank the people from Institute Technological of Materials (ITM) of the Polytechnic University of Valencia for helping us with the tribology experiments during A. Borrell's short stay in 2009.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of Carbon Nanofibers/ZrO2 Composites Properties with a Zirconia Nanocoating on Carbon Nanofibers by Sol–Gel Method

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Rocha, Victoria G.
  • Torrecillas, Ramon
  • Fernandez, Adolfo
The development of new carbon nanofibers (CNFs)–ceramic nanocomposite materials with excellent mechanical, thermal, and electrical properties is interesting for a wide range of industrial applications. Among the ceramic materials, zirconia stands out for their excellent mechanical properties. The main limitations in the preparation of this kind of nanocomposites are related with the difficulty in obtaining materials with homogeneous distribution of both phases and the dissimilar properties of CNFs and ZrO2 which causes poor interaction between them. CNFs-reinforced zirconia nanocomposites ZrO2/xCNFs (x=1–20 vol%) were prepared by powder mixture and sintered by spark plasma sintering (SPS). ZrO2-reinforced CNFs nanocomposites CNFs/xZrO2 (x=20 vol%) were prepared by powder mixture and a surface coating of CNFs by the wet chemical route with zirconia precursor is proposed as a very effective way to improve the interaction between CNFs and ZrO2. After SPS sintering, an improvement of 50% in fracture strength was found for similar nanocomposite compositions when the surface coating was used. The improved mechanical properties of these nanocomposites are caused by stronger interaction between the CNFs and ZrO2., This work was financially supported by National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her research grant BES2007-15033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of CNFs/SiC nanocomposites properties obtained from different routes and consolidated by pulsed electric-current pressure sintering

  • Rocha, Victoria G.
  • Torrecillas, Ramon
  • Fernandez, Adolfo
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The influence of the preparation route and composition on carbon nanofibers-silicon carbide (CNFs/SiC) nanocomposites' properties was studied. Nanopowders were mixed by ultrasonic dispersion or high attrition milling and the consolidation was done by pulsed electric-current pressure sintering technique. The relative density and fracture strength of high-energy attrition milled CNFs/SiC nanocomposites gradually increased with the increase of sintering temperature, from 1400 to 1800 degrees C and holding time 1 to 30 min. A chemical surface coating of CNFs with alumina precursor is proposed as a very effective way for improving the interaction between CNFs and SiC. An increase of 54% in fracture strength was achieved on the nanocomposites when the surface coating was used. As a consequence of the stronger interaction between the components, which is achieved through the use of suitable processing route and sintering parameters, and the role of nano-alumina as sintering aid improved mechanical properties was achieved. (c) 2012 Elsevier B.V. All rights reserved., This work has been carried out with the financial support of the National Plan Projects nos. MAT2006-01783 and MAT2007-30989-E and the Regional Project no. FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (no. JCI-2011-10498).