Pasar al contenido principal

MICROWAVE SINTERING OF CERAMIC NANOCOMPOSITES FOR MULTIFUNCTIONAL APPLICATIONS (MICROFUL).
THE MAIN OBJECTIVE OF THE MICROFUL PROJECT IS THE SINTERING BY THE NON-CONVENTIONAL MICROWAVE TECHNIQUE OF NANOSTRUCTURED ADVANCED CERAMIC MATERIALS WITH NEW FUNCTIONALITY.

JCI-2011-10498

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Contratación e Incorporación de RRHH
Subprograma Subprograma Juan de la Cierva (JDC)
Convocatoria Juan de la Cierva Incorporación
Año convocatoria 2011
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Formación e Incorporación de Investigadores
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructure and mechanical effects of spark plasma sintering in alumina monolithic ceramics

  • Alvarez-Clemares, I.
  • Agouram, S.
  • Torrecillas, R.
  • Fernandez, A.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The specific effects of spark plasma sintering (SPS) on the creep behavior, microstructure and mechanical properties of alumina monolithic ceramic were investigated. SPS introduces strains that concentrate at grain boundaries and inhibit crack growth, resulting in an improvement in the flexural strength and fracture toughness. However, creep blocks grain boundary movements and decreases the reliability of the material. These strains can be removed by a post-sintering thermal treatment, which plays an important role in the distribution of dislocations. Crown Copyright (c) 2012 Published by Elsevier Ltd. on behalf of Acta Materialia Inc. All rights reserved., The authors would like to acknowledge the help of the EU for the financial support received under the IP-NANOKER NMP3-CT-2005-515784. A.B. acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva Contract (JCI-2011-10498). The authors are grateful to the Central Support Service in Experimental Research (SCSIE), University of Valencia for providing the HR-TEM facility.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fabrication of near-zero thermal expansion of fully dense beta-eucryptite ceramics by microwave sintering

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • Garcia-Moreno, O.
Microwave heating is proposed as non-conventional technique for the sintering of optimal lithium aluminosilicate compositions of β-eucryptite system. The coefficient of thermal expansion and mechanical properties of the sintered samples has been studied under the influence of microwave heating. The ad hoc synthesized β-eucryptite together with the microwave sintering technique developed in this work open the opportunity to produce breakthrough materials with low or negative coefficient of thermal expansion and excellent mechanical properties, as a Young s modulus of 110 GPa. The combination of rapid heating with low energy applied by the microwave technology (eco-friendly process) and the dramatic reduction in cycle time allows densification without glass phase formation. Results of the coefficient of thermal expansion of the β-eucryptite ceramics presented here under cryogenic conditions will be of value, for example, in the future design of new composite materials for space applications, The authors would like to thank Dr. Emilio Rayon for performing the nanoindentation analysis in the Materials Technology institute (ITM) of the Polytechnic University of Valencia (UPV) and your financial support received of UPV under Projects SP20120621 and SP20120677 and Spanish Government through the Project MONIDIEL (TEC2008-04109). A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for a Juan de la Cierva contract (JCI-2011-10498) and SCSIE of the University of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of sintering technology in beta-eucryptite ceramics: Influence on fatigue life and effect of microcracks

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Martínez-Amesti, Ana
  • Fernández, Adolfo
β-eucryptite ceramics with low negative or near-zero coefficient of thermal expansion (CTE) with excellent mechanical properties, such as Young’s modulus  100 GPa, have attracted attention for many important industrial applications. The extremely anisotropic thermal expansion behaviour of this material leads to thermal residual stresses, and causes spontaneous microcracking. These microcracks cause large negative CTE with mechanical weaknesses. The appearance of microcracks is due to different factors. The most important are prolonged sintering time and heating source used. The present work shows experimentally the evolution of grain microcracks and residual stresses of the sintered -eucryptite material going through many thermal fatigue cycles (3600). The effect of stresses applied on β-eucryptite crystals due to the thermal cycling could be considered for explaining the small change observed of β-eucryptite to β-spodumene phase, which is higher in the samples obtained by microwave sintering. Therefore, the study of residual stresses has suggested that the heating source employed, such as conventional or microwave, has a great influence on thermal fatigue life and the final mechanical and thermal properties. The microwave heating has a significant impact on β-eucryptite materials lifetime., A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for a Juan de la Cierva contract (JCI-2011-10498) and the Polytechnic University of Valencia (UPV) for financial support received under project SP20120677. The authors would like to thank the SCSIE team of the University of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Sliding wear behavior of WC-Co-Cr3C2-VC composites fabricated by conventional and non-conventional techniques

  • Espinosa-Fernández, L.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Gutierrez-González, C.F.
[EN] The present work aims are to study the dry sliding wear behavior of WC-12 wt.%Co materials, with or without addition of Cr3C2/VC grain growth inhibitors, and to sinter them by two different consolidation techniques: conventional sintering and spark plasma sintering (SPS). The dry sliding wear tests were performed on a tribometer with a ball-on-disc configuration using a WC-Co ball as a counterpart material with a normal contact load of 60 N, a sliding distance of 10000 m and a sliding speed of 0.1 m/s. The influence of the grain growth inhibitors and the consolidation techniques in sintered samples were related to the friction coefficient, wear rates and wear pattern damage. Samples sintered by non-conventional technique (SPS) show the best wear resistance and lower friction coefficient. The addition of inhibitors reduces the wear rates in materials consolidated by both techniques. The differences in the wear damage are related to microstructural parameters, mechanical properties and wear rates, The work is supported financially by the Spanish Ministry of Science and Innovation by the project MAT2009-14144-C03-C02. L. Espinosa-Fernández, acknowledges the AECI program for the realization of the Ph.D in the ITM-UPV. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Al2O3-3YTZP-Graphene multilayers produced by tape casting and spark plasma sintering

  • Rincón, Acacio
  • Moreno, Rodrigo
  • Chinelatto, Adriana S. A.
  • Gutierrez-Gonzalez, Carlos F.
  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
This work aims to establish a colloidal route to obtain laminates of alumina zirconia combining layers with and without graphene. Green tapes of alumina, alumina with 5 vol.% of 3Y-TZP and alumina with 5 vol.% of 3Y-TZP and graphene-oxide (2 vol.%) were obtained by aqueous tape casting. It is possible to design materials for different structural applications with a controlled microstructure with a high number of different layers. The tapes were punched into 20-mm discs, joined to form laminates alternating up to 18-layers, and sintered in one-step by spark plasma sintering (SPS) at 1400 degrees C. It has demonstrated that there is a significant graphite diffusion provoked by the required graphite holders into the SPS-furnace. Dense laminates with layer thicknesses similar to 100 mu m and good cohesion between layers were obtained. Nanoindentation results showed that hardness and elastic modulus values were higher than 27 GPa and 300 GPa, respectively, and similar for all layers. Crown Copyright (C) 2014 Published by Elsevier Ltd. All rights reserved., This work has been supported by Spanish Ministry of Economy and Competitiviness (MAT2012-31090). A. S. A. Chinelatto thanks to CAPES - Programa Ciencias sem Fronteiras (Brazil) for the concession of a fellowship for post-doctoral sabbatical grant in ICV-CSIC, Spain. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana by the financial support for the BEST/2012/302 grant. Authors thank to Nanoinnova Technologies (Spain) for supplying the graphene oxide and helpful discussions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

ZrTiO4 materials obtained by Spark Plasma Reaction Sintering

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • García-Rocha, Victoria
  • Fernández, Adolfo
  • Gómez, Andrés
  • López-López, Emilio
  • Moreno, Rodrigo
Zirconium titanate (ZrTiO4), have many attractive properties such as high resistivity, high dielectric constant, high permittivity at microwave frequencies and excellent temperature stability for microwave properties. Zirconium titanate dense materials are proposed for many structural applications, but fully reacted and completely dense pieces are difficult to obtain by conventional routes. In this work, fully dense zirconium titanate materials ( 98%) were obtained at lower temperatures (1300 1400 C) and short processing time by non-conventional technique; spark plasma-reaction sintering (SPRS). Homogeneous and stable starting powders mixture with the adequate composition was prepared from the raw materials: m-ZrO2 ( 0.3 lm) and anatase-TiO2 ( 40 nm). Dense materials were mechanically and microstructural characterised. The fracture strength was measured by biaxial testing, giving values of about 200 MPa., This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14144-C03-02, MAT2012-38364-C03-02 and MAT2012-31090. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydrothermal Degradation Behavior of Y-TZP Ceramics Sintered by Nonconventional Microwave Technology

  • PRESENDA-BARRERA, ALVARO
  • Moreno, Rodrigo
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
Different factors such as the characteristics of starting powders, their processing, the sintering technique and the final sintering temperature were assessed with the goal to improve the low-temperature degradation (LTD) resistance of 3Y-TZP materials without compromising on the mechanical properties. The degradation of hydrothermally treated specimens was studied by AFM, nanoindentation technique, micro-Raman spectroscopy, and electron microscopy. 3Y-TZP previously prepared in laboratory by colloidal processing, and sintered by microwave method at low temperature (1200 degrees C) led to excellent mechanical and LTD resistance, as compared to dental restorations based on Y-TZP commercial material. In the former, the presence of m-phase was almost nonexistent even after 200 h of exposure to LTD conditions and the initial mechanical properties were maintained, giving 16 and 250 GPa mean values for hardness and Young's modulus, respectively. The influence of the fast-technology by microwave heating is presented with a nonconventional sintering method to fabricate 3Y-TZP ceramics for dental application with very high resistance against LTD and optimized mechanical properties., Presenda acknowledges the Generalitat Valenciana for his Santiago Grisolia scholarship (GRISOLIA/2013/035). A. Borrell acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the financial support under the GV/2014/009 project. M. D. Salvador thanks CAPES - Programa Ciencias sem Fronteiras (Brazil) for the concession of a PVE project No. A086/2013.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of graphene and CNFs addition on the mechanical and electrical properties of dense alumina-toughened zirconia composites

  • Rincón, Acacio
  • Moreno, Rodrigo
  • Chinelatto, Adriana S. A.
  • Gutierrez, Carlos F.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
Fully dense carbon/alumina-toughened zirconia composites were prepared by using a combination of aqueous colloidal powder processing and spark plasma sintering technique (SPS). Various carbon elements were introduced in alumina-toughened zirconia matrix (ZA) as filler; carbon nanofibers (CNFs) and graphene oxide (GO). The influence of the addition of different carbon forms on the microstructure and on the mechanical and electrical properties was investigated. In the case of the ZAGO composites, the SPS technique allowed, in one-step, the in situ reduction of the graphene oxide during the sintering process. The fracture toughness increases for ZAGO composites in comparison to the ZA material while the hardness decreases slightly with carbon elements addition. The electrical conductivity of the ZA composite drastically increased with the addition of graphene oxide, and it reached 10 Omega cm at 2 vol%. Crown, A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana by the financial support for the GV/2014/009 project. M.D. Salvador thanks to CAPES - Programa Ciencias sem Fronteiras (Brazil) for the concession of a PVE project No. A086/2013. A.S.A. Chinelatto thanks to CAPES for the concession of a post-doctoral fellowship in ICV-CSIC.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of particle size distribution of suspension feedstock on the microstructure and mechanical properties of suspension plasma spraying YSZ coatings

  • Carpio, Enrique
  • Bannier, Emilie
  • Moreno, Rodrigo
  • Sánchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
In this work, aqueous suspension feedstocks with different particle size distribution from submicron- and nanosized YSZ powders were prepared. A previous colloidal characterisation allowed concentrated suspensions (~40 wt%) to be prepared. These suspensions were then successfully deposited by suspension plasma spraying (SPS) onto stainless steel substrates at different spraying distances. Coatings were characterised in terms of microstructure and mechanical properties (hardness and elastic modulus) by nanoindentation. All coatings displayed a two-zone microstructure formed by partially melted areas containing nanometre or submicrometre-sized particles surrounded by fully melted areas. These partially melted areas strongly increased as standoff distance lengthened. Mechanical properties worsened with spraying distance increase. The finer the feedstock particle size the more the spraying distance effect was. A clear correlation between mechanical properties and amount of partially melted areas has been proved. Thus the use of a mixture of nano/submicron-sized particles as a SPS feedstock can represent a good balance between suspension processability and final coating performance., This work has been supported by the Spanish Ministry of Science and Innovation and by ERDF (European Regional Development Funds) (Project MAT2012-38364-C03). The authors also acknowledge the SCSIE of the University of Valencia for the FEG-SEM observations. Finally, the Research Promotion Plan of the Universitat Jaume I, action 3.1 (ref. PREDOC/2009/10) and the Spanish Ministry of Science and Innovation for Juan de la Cierva contract (JCI-2011-10498) is also grateful.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Propiedades mecánicas y coeficiente de dilatación térmica de la beta-eucriptita sinterizada por la técnica de microondas, Mechanical properties and coefficient of thermal expansion of β-eucryptite sintered by microwave technique

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • García-Moreno, Olga
[EN] Microwave non-conventional sintering technique allows obtaining fully dense glass-free β-eucryptite bulk material (∼99 %). A considerable difference in the densification, microstructure, coefficient of thermal expansion behaviour and mechanical properties, between conventional and non-conventional sintered specimens was observed. The hardness and Young’s modulus values obtained by microwaves at 1200 °C-5min have been relatively high, 6.8 GPa and 101 GPa, respectively, compared to conventional sintering (3.9 GPa and 58 GPa, respectively). Very low thermal expansion materials have been obtained in a wide temperature range including cryogenic temperatures (from -150 ºC to 150 ºC). The high heating rate along with the lower energy consumption makes microwave technique a clear alternative to other types of sintering methods., [ES] La técnica de sinterización no convencional de microondas permite obtener materiales de β-eucriptita en estado sólido cristalino con densidades cercanas a la teórica (∼99 %). Se ha observado una diferencia considerable en estos materiales respecto a la técnica convencional en términos de densificación, microestructura, coeficiente de expansión térmica y propiedades mecánicas. Los valores de dureza y módulo de Young obtenidos mediante sinterización por microondas a 1200 ºC-5 min han sido relativamente altos, 6.8 GPa y 101 GPa, respectivamente, en comparación con el material obtenido mediante horno convencional (3.9 GPa y 58 GPa, respectivamente). Los datos dilatométricos obtenidos, incluyendo el intervalo de temperatura criogénica (-150 ºC a +150 ºC), muestran un coeficiente de expansión térmica controlado y negativo en todo el rango de temperaturas. La combinación de un calentamiento rápido junto con la reducción drástica en el tiempo de ciclo y el ahorro energético, hace que la técnica de microondas sean una clara alternativa a otro tipo de calentamientos., Los autores desean agradecer al Dr. Emilio Rayón por la realización de los ensayos de nanoindentación en el Instituto de Tecnología de Materiales (ITM) de la Universidad Politécnica de Valencia (UPV). El apoyo financiero recibido de la UPV dentro de los proyectos SP20120621 y SP20120677 y, al gobierno español a través del proyecto (TEC2012-37532-C02-01). A. Borrell, agradece al Ministerio de Ciencia e Innovación su contrato de Juan la Cierva (JCI-2011-10498).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhanced properties of alumina-aluminium titanate composites obtained by spark plasma reaction-sintering of slip cast green bodies

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Rocha, Victoria G.
  • Fernandez, Adolfo
  • Molina, Tamara
  • Moreno, Rodrigo
Full dense alumina + 40 vol.% aluminium titanate composites were obtained by colloidal filtration and fast reaction-sintering of alumina/titania green bodies by spark plasma sintering at low temperatures (1250-1400 degrees C). The composites obtained had near-to-theoretical density (> 99%) with a bimodal grain size distribution. Phase development analysis demonstrated that aluminium titanate has already formed at 1300 degrees C. The mechanical properties such as Vickers hardness, flexural strength and fracture toughness of bulk composites are significantly higher than those reported elsewhere, e.g. the composite sintered at 1350 degrees C show values of about 24 GPa, 424 MPa and 5.4 MPa m(1/2), respectively. The improved mechanical properties of these composites are attributed to the enhanced densification and the finer and more uniform nanostructure achieved by non-conventional fast sintering of slip-cast dense green compacts. Crown Copyright (c) 2012 Published by Elsevier Ltd. All rights reserved., This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14369-C02-01 and MAT2009-14144-C03-02. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High thermal stability of microwave sintered low-er beta-eucryptite materials

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • García-Moreno, Olga
Low-temperature sinterable microwave LiAlSiO4-based solid-state material was investigated with regard to microwave dielectric properties as functions of the sintering temperature. beta-eucryptite materials and alumina-reinforced beta-eucryptite composites were sintered by microwave technology at 1100 degrees C and 1200 degrees C. The combination of fast heating and the dramatic reduction in cycle time, along with the non-conventional heating source, opens the way to produce materials with desired multifunctional properties. The microstructure and crystalline composition of the materials were characterised, and the mechanical, thermal and microwave dielectric behaviours were analysed. X-ray diffraction showed good chemical stability in materials without between-phase reactions during the microwave sintering process. The excellent mechanical (similar to 8 GPa of hardness and similar to 100 GPa of Young's modulus), thermal (-0.23. 10(-6) K-1) and microwave dielectric properties (epsilon(r)= 4.10; Q=1494) were obtained from the LAS/Al2O3 composites sintered at a very low temperature (1100 degrees C). The results achieved show the possibility of designing ceramic nanocomposites at low sintering temperatures using microwave technology with near-zero thermal expansion coefficients, high mechanical and chemical stability and low dielectric properties., This work has been developed by different funded projects. The authors would like to thank their financial support: Project SP20120677 funded by the Polytechnic University of Valencia (UPV), Project TEC2012-37532-C02-01 (DINAWAVE) funded from Ministerio de Economia y Competitividad (MINECO) - Spanish government- and co-funded by ERDF (European Regional Development Funds) of European Union. Author A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of microwave sintering on microstructure and mechanical properties in Y-TZP materials used for dental applications

  • Presenda, Álvaro
  • Moreno, Rodrigo
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The aim of this work is to study the application of microwave sintering to consolidate yttria-stabilized zirconia polycrystalline (Y-TZP) ceramics commonly applied in dentistry, so as to obtain highly dense materials and fine microstructure with shorter sintering cycles. Three Y-TZP materials are considered: two commercially available for dental applications and one laboratory studied powder. Microwave sintering was carried out at 1200 and 1300 degrees C for 10 min and conventional sintering at 1300 and 1400 degrees C for 2 h. Relative density, Vickers hardness and fracture toughness values for sintered samples were determined. Microwave sintering results, generally, in improved mechanical properties of the materials in terms of hardness and fracture toughness compared to conventional sintering and, in some cases, at lower sintering temperatures. A finer grain microstructure (final grain size < 250 min) was obtained with microwave sintering for both commercial materials. Fracture toughness values differ significantly between sintering techniques and chosen parameters. These results suggest that microwave heating can be employed to sinter Y-TZP commercial ceramics for dental applications obtaining improving the mechanical properties of the materials with a very important time and energy consumption reduction. Crown Copyright (C) 2015 Published by Elsevier Ltd and Techna Group S.r.l. All rights reserved., The authors would like to thank the financial support received from Universidad Politecnica de Valencia under Project 5P20120677 and Ministerio de Economia y Competitividad (MINECO) and co-funded by ERDF (European Regional Development Funds) through the Project (IEC2012-37532-C02-01). A. Borrell acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva Contract (JCI-2011-10498) and the Generalitat Valenciana for the financial support under Project GV/2014/009. A. Presenda acknowledges the Generalitat Valenciana for his Santiago Grisolia program scholarship (GRISOLLV2013/035). The authors would also like to acknowledge Prof. Dr. M. F. Sold from the Faculty of Medicine and Odontology at the Universidad de Valencia for supplying the commercial materials.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microwave, spark plasma and conventional sintering to obtain controlled thermal expansion beta-eucryptite materials

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • García Moreno, Olga
Lithium aluminosilicate was fabricated by conventional and non-conventional sintering: microwave and spark plasma sintering, from 1200 to 1300 ºC. A considerable difference in densification, microstructure, coefficient of thermal expansion behavior and hardness and Young’s modulus was observed. Microwave technology made possible to obtain fully dense glass-free lithium aluminosilicate bulk material (>99%) with near-zero and controlled coefficient of thermal expansion and relatively high mechanical properties (7.1 GPa of hardness and 110 GPa of Young’s modulus) compared to the other two processes. It is believed that the heating mode and effective particle packing by microwave sintering are responsible to improve these properties., The authors would like to thank Dr. Emilio Rayon for performing the nanoindentation analysis in the Materials Technology institute (ITM) of the Polytechnic University of Valencia (UPV) and your financial support received of UPV under project SP20120621 and SP20120677 and Spanish government through the project (TEC2012-37532-C02-01) and cofunded by ERDF (European Regional Development Funds). A. Borrell acknowledges the Spanish Ministry of Science and Innovation for a Juan de la Cierva contract (JCI-2011-10498) and SCSIE of the University of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mechanical characterization of conventional and non-conventional sintering methods of commercial and lab-synthesized Y-TZP zirconia for dental applications

  • Presenda Barrera, Álvaro
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Ceramics for dental applications have become increasingly important in the last decades. Particularly, the introduction of yttria-stabilized zirconia tetragonal polycrystalline (Y-TZP) materials as an alternative to the manufacturing of dental implants and prosthesis has provided a powerful tool to meet the demands required for these replacements in terms of biocompatibility, toughness, hardness and optical properties. Several commercial Y-TZP materials are currently available on the market and strong efforts in research and development facilities are being carried out to improve processing of Y-TZP to fully consolidate odontological pieces. Novel processing methods for ceramic powder sintering, including Y-TZP, aim to reduce processing times and production costs significantly, while maintaining or even improving the resulting microstructure and mechanical properties of the material. One of these methods includes microwave sintering. The purpose of this study is to characterize and compare the resulting properties of Y-TZP materials after conventional sintering and the non-conventional method of microwave heating. In this work one commercial material and one laboratory-synthesized Y-TZP powder are considered. The results suggest that microwave sintering results, generally, in better mechanical properties of the material in terms of hardness and fracture toughness than conventional sintering., The authors would like to thank the financial support received from Universidad Politécnica de Valencia under project SP20120677 and Ministerio de Economía y Competitividad (MINECO) and co-funded by ERDF (European Regional Development Funds) through the project (TEC2012- 37532-C02-01). A. Borrell acknowledges the Spanish Ministry of Science and Innovation for a Juan de la Cierva contract (JCI-2011-10498). A. Presenda acknowledges the Generalitat Valenciana for his Santiago Grisolía program scholarship (REF. GRISOLÍA/2013/035). The authors would also like to acknowledge the SCSIE of the University of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microwave technique: An innovated method for sintering beta-eucryptite ceramic materials

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • García-Moreno, Olga
  • Torrecillas, Ramón
[EN] Microwave sintering has emerged in recent years as a new, fast, cheap and green technology for sintering a variety of materials. The main advantages of microwave heating can be summarized as follow: reduced processing times, energy costs and environmental benefits. Nevertheless, understanding how this specific heating drives to obtain ceramic materials with a combination of unique, structural and functional properties is the big challenge. The present work shows the different and improved properties achieved with β-eucryptite nanocomposite ceramic materials by microwave heating compared with the conventional method. Microcracking evolution in addition to the microstructure of the sintered materials along the several thermal cycles has been studied. Mechanical properties changes observed can be related to this process. Thus, the microwave technique is a promising tool for sintering new materials by controlling the composition of the phases, chemical reactivity and nanostructure, using up to 70% less energy in the whole sintering process than conventional heating. This technique ecomes part of the new and innovative technologies "eco-green"., The authors would like to thank the financial support received of UPV under project SP20120677 and Ministerio de Economía y Competitividad (MINECO) and co-funded by ERDF (European Regional Development Funds) through the project (TEC2012-37532-C02-01). A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for a Juan de la Cierva contract (JCI-2011-10498) and SCSIE of the University of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bulk TiCxN1-x-15%Co cermets obtained by direct spark plasma sintering of mechanochemical synthesized powders

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Rocha, Victoria G.
  • Fernandez, Adolfo
  • Angel Aviles, Miguel
  • Gotor, Francisco J.
TiCxN1-x-15 wt.%Co cermets were obtained by a mechanically induced self-sustaining reaction (MSR) and sintered by spark plasma sintering (SPS) technique at different temperatures (1200-1400 degrees C) for 1 min in vacuum under a uniaxial load of 80 MPa. The evolution of microstructure and mechanical properties was investigated. SPS allowed high densification with limited grain growth at a relatively low temperature. Material sintered at 1300 degrees C showed a good combination of mechanical properties with Vickers hardness of 17.1 +/- 0.5 GPa, fracture toughness of 5.51 +/- 0.29 MPa m(1/2) and bending strength of 904 +/- 12 MPa. Lower sintering temperature resulted in a decrease in bending strength due to poor cohesion between the ceramic and binder phases. An increase in sintering temperature would allow tailoring the cermet microstructure and, therefore, adjusting the Vickers hardness/fracture toughness relation. Crown Copyright (C) 2012 Published by Elsevier Ltd. All rights reserved., This work was supported by the Spanish Government under grant (MAT2011-22981), which is financed in part by the European Regional Development Fund of 2007-2013. A. Borrell acknowledges the Spanish Ministry of Science and Innovation for her "Juan de la Cierva" contract (JCI-2011-10498).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fast route to obtain Al2O3-based nanocomposites employing graphene oxide: Synthesis and Sintering

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Busquets Mataix, David Jeronimo|||0000-0001-5031-7805
  • Pruna, Alina Iuliana
  • Pullini, Daniele
A fast approach based on microwave technology was employed for the sintering of novel composites of alumina and using graphene oxide (GO) as susceptor. The thermal stability and structure of GO materials produced by chemical oxidation of graphite were characterized. The morphology, structure and mechanical properties of the composites sintered by microwave approach were reported to the counterparts sintered by conventional method. The results indicated the formation of an interconnecting graphene network promoted the electrical conductivity in the composite having only 2 wt.% GO. Hardness and elastic modulus decreased significantly in samples sintered by conventional method due to lower values of density while microwave technology allowed to achieve a positive effect on the densification and showed a smaller grain size when compared to the one achieved by conventional heating. (C) 2014 Elsevier Ltd. All rights reserved., Financial support from European Commission (project no. NMP3-SL-2010-246073), Universidad Politecnica de Valencia (project SP20120677) and Ministerio de Economia y Competitividad - MINECO (project TEC2012-37532-C02-01, co-funded by ERDF (European Regional Development Funds) is gratefully acknowledged. A.B. acknowledges the Spanish Ministry of Science and Innovation (contract JCI-2011-10498). A.P. acknowledges support from Romanian Authority for Scientific Research - UEFISCDI (project no. PN-II-RU-PD-2012-3-0124).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructure and mechanical properties of plasma spraying coatings from YSZ feedstocks comprising nano- and submicron-sized particles

  • Carpio, Pablo
  • Gómez, Andres
  • Martínez, Eduardo
  • Sánchez, Enrique
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
Atmospheric plasma spraying (APS) is an attractive technique to obtain nanostructured coatings due to its versatility, simplicity and relatively low cost. However, nanoparticles cannot be fed into the plasma using conventional feeding systems, due to their low mass and poor flowability, and must be adequately reconstituted into sprayable micrometric agglomerates. In this work, nanostructured and submicron/nanostiuctured powders of yttria-stabilised zirconia (YSZ) were deposited using APS, with a view to obtaining high-performance thermal bather coatings (IBC). All powders were reconstituted by spray-drying from different solid loading suspensions, followed by a thermal treatment of the spray-dried granules to reduce agglomerate porosity and enhance powder sinterability. The reconstituted granules were characterised by XRD, SEM, pore sizing and flowability evaluation. The reconstituted feedstocks were successfully deposited onto metallic substrates by APS. A metallic bond coat was sprayed between the substrate and the ceramic layer. The coating microstructure, characterised by SEM, was formed by partially melted zones, which retained the initial powder microstructure, embedded in a fully melted matrix which acts as a binder. It was shown that feedstock characteristics which in turn are very dependent of starting suspension characteristics, in particular agglomerate density and primary particle size, impact on coating microstructure (porosity and amount of partially-melted areas). For this reason mechanical properties of coatings are also strongly affected by feeding powder characteristics. (C) 2014 Elsevier Ltd and Techna Group S.r.l. All rights reserved., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2012-38364-C03), by the Research Promotion Plan of the Universitat Jaume I, action 3.1 (ref. PREDOC/2009/10) and it has been co-funded by ERDF (European Regional Development Funds). The authors also acknowledge the SCIC of Valencia University for the FEG-SEM observations. Finally the Spanish Ministry of Science and Innovation for Juan de la Cierva contract (JCI-2011-10498) is also grateful.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of CNFs/SiC nanocomposites properties obtained from different routes and consolidated by pulsed electric-current pressure sintering

  • Rocha, Victoria G.
  • Torrecillas, Ramon
  • Fernandez, Adolfo
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The influence of the preparation route and composition on carbon nanofibers-silicon carbide (CNFs/SiC) nanocomposites' properties was studied. Nanopowders were mixed by ultrasonic dispersion or high attrition milling and the consolidation was done by pulsed electric-current pressure sintering technique. The relative density and fracture strength of high-energy attrition milled CNFs/SiC nanocomposites gradually increased with the increase of sintering temperature, from 1400 to 1800 degrees C and holding time 1 to 30 min. A chemical surface coating of CNFs with alumina precursor is proposed as a very effective way for improving the interaction between CNFs and SiC. An increase of 54% in fracture strength was achieved on the nanocomposites when the surface coating was used. As a consequence of the stronger interaction between the components, which is achieved through the use of suitable processing route and sintering parameters, and the role of nano-alumina as sintering aid improved mechanical properties was achieved. (c) 2012 Elsevier B.V. All rights reserved., This work has been carried out with the financial support of the National Plan Projects nos. MAT2006-01783 and MAT2007-30989-E and the Regional Project no. FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (no. JCI-2011-10498).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influencia de los parámetros de proyección por plasma atmosférico en recubrimientos de YSZ obtenidos a partir de polvos micro y nanoestructurados, Influence of atmospheric plasma spray parameters on YSZ coatings obtained from micro and nanostructured feedstocks

  • Carpio, Pablo
  • Bannier, Emilie
  • Sánchez, Enrique
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[ES] En el presente trabajo se ha estudiado la influencia de cada uno de los parámetros de la proyección térmica por plasma atmosférico (atmospheric plasma spraying, APS) en la deposición de dos polvos comerciales de YSZ, uno convencional y otro nanoestructurado. En primer lugar se ha estudiado cómo afecta la variabilidad de los diferentes parámetros en el comportamiento de las partículas durante la proyección. Para tal fin, se ha utilizado un sensor que permite determinar la temperatura y la velocidad de las partículas en el interior del plasma. Una vez conocido cómo influyen los parámetros de proyección se han depositado ambos polvos sobre sustratos de acero inoxidable mediante APS modificando aquellos parámetros con un mayor impacto en el comportamiento de las partículas. Estos recubrimientos han sido caracterizados y se ha analizado la influencia del comportamiento de las partículas durante la proyección en la microestructura y propiedades del recubrimiento final. En este trabajo se concluye que la variación de los parámetros de proyección afecta en la velocidad y temperatura de las partículas en el interior del plasma y este comportamiento influye a su vez, y de forma diferente al emplear los distintos polvos (micro- y nanoesctructurado) en las características de los recubrimientos finales., [EN] In the present work, the influence of atmospheric plasma spray (APS) parameters on the deposition of two commercial YSZ feedstocks, one conventional and one nanostrcutured, has been studied. First the study focused on how the variability of the different parameters affects the particle behaviour during spraying. For this purpose, a sensor which enables to measure the particle temperature and velocity inside the plasma was used. Once the spraying parameters influence was known, both powders were deposited by APS onto stainless steel substrates modifying the higher influencing parameters. These coatings have been characterised and the influence of the particle behaviour on the coating microstructure and properties has been analysed. This work concludes the spraying parameters variation affects on the particle velocity and temperature inside the plasma plume and this behaviour influences, in turn but in a different way, on the final coating characteristics when using different powders (micro- and nanostructured)., Este trabajo ha sido financiado por el Ministerio Español de Economía y Competitividad (MAT2012-38364-C03) y el Plan de Promoción a la Investigación de la Universidad Jaume I, acción 2.4 (ref. E-2012-04) y acción 3.1 (ref. PREDOC/2009/10). Los autores están agradecidos con el Servicio Central de Soporte a la Investigación Experimental (SCSIE) de la Universitat de Valencia por el uso del MEB. A. Borrell agradece al Ministerio Español de Ciencia e Innovación su contrato Juan de la Cierva (JCI-2011-10498).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

EPD and Spark Plasma Sintering of bimodal alumina/titania concentrated suspensions

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Rocha, Victoria G.
  • Fernández, Adolfo
  • Molina, Tamara
  • Moreno, Rodrigo
Alumina-aluminium titanate (A-AT) composites and laminates have been recently investigated because they can provide improved flaw tolerance and toughness associated to a microcracking mechanism. A-AT composites have been produced by slip casting and reaction sintering of submicron sized alumina and titania powders. This work deals with the preparation of thick self-sustained A-AT films from mixtures of submicron sized alumina and nanosized titania powders and further sintering by conventional and non-conventional (spark plasma sintering, SPS) methods. Suspensions were prepared in water to high solid loadings, up to 50 vol.%. Self-sustained films were obtained by aqueous electrophoretic deposition (EPD) using graphite substrates under constant current density conditions. The evolution of mass per unit area with current density and deposition time was recorded. The films were characterized in the green state and after sintering at different temperatures (1300-1400) degrees C. Fully dense A-AT reaction sintered materials were obtained at low temperature by SPS, This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14369-C02-01 and MAT2009-14144-C03-02. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microwave Technique: A Powerful Tool for Sintering Ceramic Materials

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • Miranda, Míriam
[EN] Microwave sintering has emerged in recent years as a promising technology for faster, cheaper and eco-friendlier processing of a wide variety of materials, which are regarded as significant advantages against conventional sintering procedures. The present investigation describes a technique for sintering two different ceramic materials by microwave heating: alumina-15vol.% zirconia and hydroxyapatite nanopowders. The results show that microwave sintering achieves higher density values, excellent mechanical properties and a homogeneous microstructure at lower sintering temperatures. The densities of microwave processed samples were close to the theoretical densities, and the near-net-shape of the green body was preserved without significant dimensional changes. The main advantages of microwave heating can be summarized as follows: a more flexible process, reduced processing times and production costs, and environmental benefits. Thus, microwaves are a clear alternative to conventional heating methods, using up to 70% less energy throughout the whole sintering process, This work has been carried out under a programme that supports research and development at the Polytechnic University of Valencia under multidisciplinary projects PAID2011/059, SP20120621 and SP20120677. A. Borrell acknowledges the Spanish Ministry of Science and Innovation for her JdC contract (JCI2011-10498). A. Borrell and F. L. Penaranda-Foix want to thank the Generalitat Valenciana for the grant obtained in the frame of the Program BEST/2012.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mechanical properties and microstructural evolution of alumina-zirconia nanocomposites by microwave sintering

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Pallone, Eliria
Microwave sintering has emerged in recent years as a novel method for sintering a variety of materials that have shown significant advantages against conventional sintering procedures. This work involved an investigation of microwave hybrid fast firing of alumina–zirconia nanocomposites using commercial alumina powder and monoclinic nanometric zirconia. The suspensions were prepared separately in order to obtain 5, 10 and 15 vol% of ZrO2 in the alumina matrix. The samples were sintered in a monomode microwave furnace at 2.45 GHz in air at different temperatures in the range 1200–1400 1C with 10 min of dwelling time and 200 1C/min of heating rate. The effect of sintering temperature in densification, mechanical properties and microstructure behavior of the composites was investigated. Higher density, hardness and Young's modulus, excellent fracture toughness properties and homogeneous microstructure were achieved by microwave sintering in comparison to conventional heating. Microstructure analysis showed that the alumina grains had not grown significantly, indicating that the zirconia particles provided a hindering effect on the grain growth of alumina. Crown Copyright & 2014 Published by Elsevier Ltd and Techna Group S.r.l. All rights reserved, The authors would like to thank the Polytechnic University of Valencia (UPV) for financial support received for projects SP20120621, SP20120398 and SP20120677 and Spanish Government (TEC2012-37532-C02-01) and co-funded by ERDF (European Regional Development Funds). A. Borrell acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and Generalitat Valenciana by Geronimo Forteza funding (FPA/2012/022).