Pasar al contenido principal

SYNTHESIS AND COLLOIDAL PROCESSING OF NANOSTRUCTURED COATINGS AND COMPOSITES

MAT2012-31090

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2012
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Secretaría de Estado de Investigación, Desarrollo e Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Al2O3-3YTZP-Graphene multilayers produced by tape casting and spark plasma sintering

  • Rincón, Acacio
  • Moreno, Rodrigo
  • Chinelatto, Adriana S. A.
  • Gutierrez-Gonzalez, Carlos F.
  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
This work aims to establish a colloidal route to obtain laminates of alumina zirconia combining layers with and without graphene. Green tapes of alumina, alumina with 5 vol.% of 3Y-TZP and alumina with 5 vol.% of 3Y-TZP and graphene-oxide (2 vol.%) were obtained by aqueous tape casting. It is possible to design materials for different structural applications with a controlled microstructure with a high number of different layers. The tapes were punched into 20-mm discs, joined to form laminates alternating up to 18-layers, and sintered in one-step by spark plasma sintering (SPS) at 1400 degrees C. It has demonstrated that there is a significant graphite diffusion provoked by the required graphite holders into the SPS-furnace. Dense laminates with layer thicknesses similar to 100 mu m and good cohesion between layers were obtained. Nanoindentation results showed that hardness and elastic modulus values were higher than 27 GPa and 300 GPa, respectively, and similar for all layers. Crown Copyright (C) 2014 Published by Elsevier Ltd. All rights reserved., This work has been supported by Spanish Ministry of Economy and Competitiviness (MAT2012-31090). A. S. A. Chinelatto thanks to CAPES - Programa Ciencias sem Fronteiras (Brazil) for the concession of a fellowship for post-doctoral sabbatical grant in ICV-CSIC, Spain. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana by the financial support for the BEST/2012/302 grant. Authors thank to Nanoinnova Technologies (Spain) for supplying the graphene oxide and helpful discussions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

ZrTiO4 materials obtained by Spark Plasma Reaction Sintering

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • García-Rocha, Victoria
  • Fernández, Adolfo
  • Gómez, Andrés
  • López-López, Emilio
  • Moreno, Rodrigo
Zirconium titanate (ZrTiO4), have many attractive properties such as high resistivity, high dielectric constant, high permittivity at microwave frequencies and excellent temperature stability for microwave properties. Zirconium titanate dense materials are proposed for many structural applications, but fully reacted and completely dense pieces are difficult to obtain by conventional routes. In this work, fully dense zirconium titanate materials ( 98%) were obtained at lower temperatures (1300 1400 C) and short processing time by non-conventional technique; spark plasma-reaction sintering (SPRS). Homogeneous and stable starting powders mixture with the adequate composition was prepared from the raw materials: m-ZrO2 ( 0.3 lm) and anatase-TiO2 ( 40 nm). Dense materials were mechanically and microstructural characterised. The fracture strength was measured by biaxial testing, giving values of about 200 MPa., This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14144-C03-02, MAT2012-38364-C03-02 and MAT2012-31090. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.