Pasar al contenido principal

SINTESIS DE MATERIALES NANOESTRUCTURADOS PARA LA OBTENCION DE BARRERAS TERMICAS MEDIANTE TECNICAS INNOVADORAS DE PROYECCION TERMICA POR PLASMA

MAT2012-38364-C03-02

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2012
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Secretaría de Estado de Investigación, Desarrollo e Innovación
Centro beneficiario UNIVERSITAT DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multilayer and particle size-graded YSZ coatings obtained by plasma spraying of micro- and nanostructured feedstocks

  • Carpio, Pablo
  • Bannier, Emilie
  • Sanchez Vilches, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Benavente Martínez, Rut|||0000-0002-4566-9475
This work was supported by the Spanish Ministry of Science and Innovation (Project MAT2012-38364-C03) and the Research Promotion Plan of Universitat Jaume I, action 3.1 (Ref. PREDOC/2009/10), and it has been co-funded by the European Regional Development Fund (ERDF). The authors also thank the SCIC of Universitat Jaume I for the FEG-SEM observations
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comportamiento a fatiga térmica de la capa de anclaje de nuevas barreras térmicas cerámicas obtenidas mediante proyección por plasma atmosférico, Thermal fatigue behavior of new ceramic thermal barrier coatings obtained by the atmospheric plasma spray process

  • Carpio-Cobo, Pablo
  • Sánchez Vilches, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[PT] O desenvolvimento de novos materiais cerâmicos para aplicá-los em recobrimentos protetores frente à temperatura, também conhecidos como barreiras térmicas (Thermal Barrier Coatings o TBC), é de grande interesse para muitos setores, entre os que destacam as indústrias de geração de energia, aeronáutica e automobilística. Neste trabalho se realizou um estudo do comportamento à fadiga térmica, centrado na resposta de um dos componentes que constituem uma TBC: a camada de fixação. Os distintos componentes da TBC foram depositados mediante a técnica de projeção térmica por plasma atmosférico (Atmospheric Plasma Spraying ou APS). Estudouse a microestrutura e a composição da camada de fixação ao longo dos ciclos térmicos de estudo., [EN] The development of new ceramic materials to protect the metallic components against corrosion and oxidation at high temperature, also known as thermal barriers coating (TBC), is of a great interest topic for many industrial and consumer sectors, such as energy generation, aeronautics and automotive industries. This paper carried out a study on the thermal fatigue behavior of the bond coat, by centering the answer in one of the components which constitute a TBC: the anchor coat. The different TBC components were deposited by an Atmospheric Plasma Spraying (APS) Technique. Microstructure and anchor coat composition along the thermal cycles were studied., Este trabajo fue financiado por el Ministerio Español de Economía y Competitividad (MINECO), con fondos FEDER, a través de los proyectos MAT2012- 38364-C03 y MAT2015-67586-C3-R. La Dra. Amparo Borrell agradece al MINECO su contrato de Juan de la Cierva, IJCI-2014-19839, y Pablo Carpio agradece su contrato predoctoral del Plan de Promoción de la Universitat Jaume I, acción 3.1 (Ref. PREDOC/2009/10).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of TiO2 addition on the microstructure and nanomechanical properties of Al2O3 Suspension Plasma Sprayed coatings

  • Bannier, E.
  • Vicent, M.
  • Sánchez, E.
  • E. Rayón|||0000-0002-0653-2046
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
Alumina-titania coatings are widely used in industry for wear, abrasion or corrosion protection components. Such layers are commonly deposited by atmospheric plasma spraying (APS) using powder as feedstock. In this study, both Al2O3 and Al2O3-13 wt% TiO2 coatings were deposited on austenitic stainless steel coupons by suspension plasma spraying (SPS). Two commercial suspensions of nanosized Al2O3 and TiO2 particles were used as starting materials. The coatings microstructure and phase composition were fully characterised using FEG-SEM and XRD techniques. Nanoindentation technique was used to determine the coatings hardness and elastic modulus properties. Results have shown that the addition of titania to alumina SPS coatings causes different crystalline phases and a higher powder melting rate is reached. The higher melted material achieved, when titania is added leads to higher hardness and elastic modulus when the same spraying parameters are used. (C) 2014 Elsevier B.V. All rights reserved., This work has been supported by the Spanish Ministry of Economy and Competitiveness (INNOBAR Project, reference: MAT2012-38364-C03) and it has been co-funded by ERDF (European Regional Development Funds).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

ZrTiO4 materials obtained by Spark Plasma Reaction Sintering

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • García-Rocha, Victoria
  • Fernández, Adolfo
  • Gómez, Andrés
  • López-López, Emilio
  • Moreno, Rodrigo
Zirconium titanate (ZrTiO4), have many attractive properties such as high resistivity, high dielectric constant, high permittivity at microwave frequencies and excellent temperature stability for microwave properties. Zirconium titanate dense materials are proposed for many structural applications, but fully reacted and completely dense pieces are difficult to obtain by conventional routes. In this work, fully dense zirconium titanate materials ( 98%) were obtained at lower temperatures (1300 1400 C) and short processing time by non-conventional technique; spark plasma-reaction sintering (SPRS). Homogeneous and stable starting powders mixture with the adequate composition was prepared from the raw materials: m-ZrO2 ( 0.3 lm) and anatase-TiO2 ( 40 nm). Dense materials were mechanically and microstructural characterised. The fracture strength was measured by biaxial testing, giving values of about 200 MPa., This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14144-C03-02, MAT2012-38364-C03-02 and MAT2012-31090. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mechanical properties of double-layer and graded composite coatings of YSZ obtained by atmospheric plasma spraying

  • Carpio-Cobo, Pablo
  • Lusvarghi, L.
  • Sanchez, E.
  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
Double-layer and graded composite coatings of yttria-stabilized zirconia were sprayed on metallic substrates by atmospheric plasma spray. The coating architecture was built up by combining two different feedstocks: one micro- and one nanostructured. Microstructural features and mechanical properties (hardness and elastic modulus) of the coatings were determined by FE-SEM microscopy and nanoindentation technique, respectively. Additional adherence and scratch tests were carried out in order to assess the failure mechanisms occurring between the layers comprising the composites. Microstructural inspection of the coatings confirms the two-zone microstructure. This bimodal microstructure which is exclusive of the layer obtained from the nanostructured feedstock negatively affects the mechanical properties of the whole composite. Nanoindentation tests suitably reproduce the evolution of mechanical properties through coatings thickness on the basis of the position and/or amount of nanostructured feedstock used in the depositing layer. Adhesion and scratch tests show the negative effect on the coating adhesion of layer obtained from the nanostructured feedstock when this layer is deposited on the bond coat. Thus, the poor integrity of this layer results in lower normal stresses required to delaminate the coating in the adhesion test as well as minor critical load registered by using the scratch test., This work has been supported by the Spanish Ministry of Science and Innovation (Project MAT2012-38364-C03) and co-funded by ERDF (European Regional Development Funds).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Sliding Wear Behavior of Al2O3-TiO2 Coatings Fabricated by the Suspension Plasma Spraying Technique

  • Klyatskina, Elizaveta
  • Espinosa Fernández, Lissette
  • Darut, G.
  • Montavon, G.
  • Agorges, H.
  • Segovia-López, Francisco|||0000-0002-4143-5751
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[EN] The friction and dry sliding wear behavior of alumina and alumina-titania near-nanometric coatings were examined. Coatings were obtained by the suspension plasma spraying technique. Dry sliding wear tests were performed on a ball-on-disk tribometer, with an Al2O3 ball as counterpart material, a normal load of 2 N, a sliding distance of 1200 m and a sliding speed of 0.1 m/s. The effect of including TiO2 in the fabricated coatings on friction coefficient behavior, wear rates and wear damage patterns was determined. The addition of TiO2 to the coatings was found to greatly increase wear resistance by, for example, 2.6-fold for 40 wt% of TiO2. The analysis of the wear surface was correlated with microstructural parameters, mechanical properties and wear rates., The authors wish to thank for the Spanish Ministry of Economy and Competitiveness (MAT2012-38364-C03) and the Autonomous Government of Valencia for funding for the stay in SPCTS-UMR CNRS (France), and the French FCENANOSURF consortium funded by the French Ministry and Industry and local governments of Region Centre and Region Limousin.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Preparation of feedstocks from nano/submicron-sized TiO2 particles to obtain photocatalytic coatings by atmospheric plasma spraying

  • Bordes, María del Carmen
  • Vicent, Monica
  • Moreno, Arnaldo
  • López, Verónica
  • Moreno, Rodrigo
  • Sanchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Benavente Martínez, Rut|||0000-0002-4566-9475
Atmospheric plasma spraying (APS) has been proved useful in obtaining TiO2 coatings with effective photocatalytic activity. However, the influence of feedstock characteristics on photocatalytic activity has hardly been addressed. This study was undertaken to prepare TiO2 photocatalytic coatings by APS from different feedstocks. The feedstocks were obtained by spray drying suspensions of a nano- and a submicron-sized TiO2 powder, with different solids contents and/or ratios of the nano- to submicron-sized particles. All the resulting powders were fully characterised to assess their suitability for use in APS processes. Feedstock powders were then deposited on steel coupons by APS using hydrogen or helium as secondary plasma gas. Coating microstructure and phase composition were characterised. Coating photocatalytic activity was determined by measuring the degradation of methylene blue dye in an aqueous solution. Powder characterisation showed that all feedstocks met plasma spray operation requirements with regard to agglomerate size distribution and density, as well as to powder flowability. Optimum agglomerate density was obtained when a well-balanced mixture of nano- and subrnicronsized particles was used. All coatings displayed a bimodal microstructure with partially melted agglomerates that retained the initial nano- or submicron-sized structure and composition (anatase phase) of the feedstock, surrounded by a fully melted matrix mainly formed by ruffle. As expected, coating porosity as well as the amount of partially melted areas depended strongly on plasma spray conditions and on feedstock characteristics. With regard to photocatalytic activity, a reasonably good fit of a first-order kinetic model to the experimental data was found for all coatings. The kinetic constants obtained displayed higher values than those of a commercial sol-gel coating. The values of these constants were related to feedstock characteristics as well as to plasma spraying conditions on the basis of anatase content. The contribution of other factors to the resulting coating surface is also discussed., This work has been supported by the Spanish Ministry of Economy and Competitiveness (Project MAT2012-38364-C03) and co-funded by the ERDF (European Regional Development Fund), as well as by University Jaume I of Castellon (P1 . 1B2013-69).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of particle size distribution of suspension feedstock on the microstructure and mechanical properties of suspension plasma spraying YSZ coatings

  • Carpio, Enrique
  • Bannier, Emilie
  • Moreno, Rodrigo
  • Sánchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
In this work, aqueous suspension feedstocks with different particle size distribution from submicron- and nanosized YSZ powders were prepared. A previous colloidal characterisation allowed concentrated suspensions (~40 wt%) to be prepared. These suspensions were then successfully deposited by suspension plasma spraying (SPS) onto stainless steel substrates at different spraying distances. Coatings were characterised in terms of microstructure and mechanical properties (hardness and elastic modulus) by nanoindentation. All coatings displayed a two-zone microstructure formed by partially melted areas containing nanometre or submicrometre-sized particles surrounded by fully melted areas. These partially melted areas strongly increased as standoff distance lengthened. Mechanical properties worsened with spraying distance increase. The finer the feedstock particle size the more the spraying distance effect was. A clear correlation between mechanical properties and amount of partially melted areas has been proved. Thus the use of a mixture of nano/submicron-sized particles as a SPS feedstock can represent a good balance between suspension processability and final coating performance., This work has been supported by the Spanish Ministry of Science and Innovation and by ERDF (European Regional Development Funds) (Project MAT2012-38364-C03). The authors also acknowledge the SCSIE of the University of Valencia for the FEG-SEM observations. Finally, the Research Promotion Plan of the Universitat Jaume I, action 3.1 (ref. PREDOC/2009/10) and the Spanish Ministry of Science and Innovation for Juan de la Cierva contract (JCI-2011-10498) is also grateful.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Role of suspension preparation in the spray drying process to obtain nano/submicrostructured YSZ powders for atmospheric plasma spraying

  • Carpio, Pablo
  • Moreno, Rodrigo
  • Gomez, Andres
  • Sanchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
2014AbstractThermal barrier coatings were manufactured by atmospheric plasma spray process from YSZ powders. These powders were made by a reconstitutionprocess which consists in a spray-drying of suspensions followed by thermal treatment of the granules.Nano- and submicron-sized YSZ particles were used as starting material. Feeding well dispersed suspension to spray-drying chamber is thefirst key step in the reconstitution process. With this aim, concentrated, stable YSZ suspensions were obtained by means of the optimisation of thepreparation conditions. Then reconstituted granules were produced by spray-drying of the YSZ suspensions and the following thermal treatmentwhich was optimised.The reconstituted powders were then successfully deposited on austenitic stainless steel coupons by APS. The findings in this work proved thatthe reconstituted powders characteristics which in turn are related to the starting suspension properties affect the final coating microstructure interms of the amount of unmelted zones, This work has been supported by the Spanish Ministry of Economy and Competitiveness (MAT2012-38364-C03) and the Research Promotion Plan of the Universitat Jaume I, action 2.4 (ref. E-2012-04) and action 3.1 (ref. PREDOC/2009/10).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructure and mechanical properties of plasma spraying coatings from YSZ feedstocks comprising nano- and submicron-sized particles

  • Carpio, Pablo
  • Gómez, Andres
  • Martínez, Eduardo
  • Sánchez, Enrique
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
Atmospheric plasma spraying (APS) is an attractive technique to obtain nanostructured coatings due to its versatility, simplicity and relatively low cost. However, nanoparticles cannot be fed into the plasma using conventional feeding systems, due to their low mass and poor flowability, and must be adequately reconstituted into sprayable micrometric agglomerates. In this work, nanostructured and submicron/nanostiuctured powders of yttria-stabilised zirconia (YSZ) were deposited using APS, with a view to obtaining high-performance thermal bather coatings (IBC). All powders were reconstituted by spray-drying from different solid loading suspensions, followed by a thermal treatment of the spray-dried granules to reduce agglomerate porosity and enhance powder sinterability. The reconstituted granules were characterised by XRD, SEM, pore sizing and flowability evaluation. The reconstituted feedstocks were successfully deposited onto metallic substrates by APS. A metallic bond coat was sprayed between the substrate and the ceramic layer. The coating microstructure, characterised by SEM, was formed by partially melted zones, which retained the initial powder microstructure, embedded in a fully melted matrix which acts as a binder. It was shown that feedstock characteristics which in turn are very dependent of starting suspension characteristics, in particular agglomerate density and primary particle size, impact on coating microstructure (porosity and amount of partially-melted areas). For this reason mechanical properties of coatings are also strongly affected by feeding powder characteristics. (C) 2014 Elsevier Ltd and Techna Group S.r.l. All rights reserved., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2012-38364-C03), by the Research Promotion Plan of the Universitat Jaume I, action 3.1 (ref. PREDOC/2009/10) and it has been co-funded by ERDF (European Regional Development Funds). The authors also acknowledge the SCIC of Valencia University for the FEG-SEM observations. Finally the Spanish Ministry of Science and Innovation for Juan de la Cierva contract (JCI-2011-10498) is also grateful.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Atmospheric plasma spraying coatings from alumina titania feedstockcomprising bimodal particle size distributions

  • Vicent, Mónica
  • Bannier, Emilie
  • Moreno, Rodrigo
  • Sanchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
In this work, Al2O3 13 wt% TiO2 submicron-nanostructured powders were deposited using atmospheric plasma spraying. The feedstocks were obtained by spray drying two starting suspensions of different solids content, prepared by adding nanosized TiO2 and submicron-sized Al2O3 powders to water. The spray-dried granules were heat-treated to reduce their porosity and the powders were fully characterised in both untreated and thermally treated state. Comparison with two commercial feedstocks was carried out. Characterisation allowed a temperature for the thermal treatment to be chosen on the basis of the sprayability of the feedstock and the preservation as much as possible of the submicron-sized structure of the unfired agglomerates. Optimisation of the deposition conditions enabled the reconstituted powdrs to be successfully deposited, yielding coatings that were well bonded to the substrate. The coating microstructure, characterised by SEM, was mostly formed by a matrix of fully molten particles where the presence of semi-molten feedstock agglomerates was also observed. Moreover, microhardness, toughness, adhesion and tribological behaviours were determined, and the impact of the granule characteristics on these properties was studied. It was found that changing the feedstock characteristics allows controlling the coating quality and properties. In general, good mechanical properties were obtained using a feedstock comprising a binary mixture of submicrometric Al2O3 and nanometric TiO2 particles in the spray-dried powder, This work has been supported by Spanish Ministry of Economy and Competitiveness (MAT2009-14144-C03 and MAT2012-38364-C03).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influencia de los parámetros de proyección por plasma atmosférico en recubrimientos de YSZ obtenidos a partir de polvos micro y nanoestructurados, Influence of atmospheric plasma spray parameters on YSZ coatings obtained from micro and nanostructured feedstocks

  • Carpio, Pablo
  • Bannier, Emilie
  • Sánchez, Enrique
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[ES] En el presente trabajo se ha estudiado la influencia de cada uno de los parámetros de la proyección térmica por plasma atmosférico (atmospheric plasma spraying, APS) en la deposición de dos polvos comerciales de YSZ, uno convencional y otro nanoestructurado. En primer lugar se ha estudiado cómo afecta la variabilidad de los diferentes parámetros en el comportamiento de las partículas durante la proyección. Para tal fin, se ha utilizado un sensor que permite determinar la temperatura y la velocidad de las partículas en el interior del plasma. Una vez conocido cómo influyen los parámetros de proyección se han depositado ambos polvos sobre sustratos de acero inoxidable mediante APS modificando aquellos parámetros con un mayor impacto en el comportamiento de las partículas. Estos recubrimientos han sido caracterizados y se ha analizado la influencia del comportamiento de las partículas durante la proyección en la microestructura y propiedades del recubrimiento final. En este trabajo se concluye que la variación de los parámetros de proyección afecta en la velocidad y temperatura de las partículas en el interior del plasma y este comportamiento influye a su vez, y de forma diferente al emplear los distintos polvos (micro- y nanoesctructurado) en las características de los recubrimientos finales., [EN] In the present work, the influence of atmospheric plasma spray (APS) parameters on the deposition of two commercial YSZ feedstocks, one conventional and one nanostrcutured, has been studied. First the study focused on how the variability of the different parameters affects the particle behaviour during spraying. For this purpose, a sensor which enables to measure the particle temperature and velocity inside the plasma was used. Once the spraying parameters influence was known, both powders were deposited by APS onto stainless steel substrates modifying the higher influencing parameters. These coatings have been characterised and the influence of the particle behaviour on the coating microstructure and properties has been analysed. This work concludes the spraying parameters variation affects on the particle velocity and temperature inside the plasma plume and this behaviour influences, in turn but in a different way, on the final coating characteristics when using different powders (micro- and nanostructured)., Este trabajo ha sido financiado por el Ministerio Español de Economía y Competitividad (MAT2012-38364-C03) y el Plan de Promoción a la Investigación de la Universidad Jaume I, acción 2.4 (ref. E-2012-04) y acción 3.1 (ref. PREDOC/2009/10). Los autores están agradecidos con el Servicio Central de Soporte a la Investigación Experimental (SCSIE) de la Universitat de Valencia por el uso del MEB. A. Borrell agradece al Ministerio Español de Ciencia e Innovación su contrato Juan de la Cierva (JCI-2011-10498).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of the initial particle size distribution on the properties of suspension plasma sprayed Al2O3-TiO2 coatings

  • Vicent, M.
  • Bannier, E.
  • Carpio, P.
  • Sánchez, E.
  • E. Rayón|||0000-0002-0653-2046
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
Al2O3-TiO2 coatings have been deposited by atmospheric plasma spraying from agglomerated, nanostructured powders showing better properties than those of their conventional (microstructured) counterparts. These nanostructured coatings can be also obtained by suspension plasma spraying however the research on suspension plasma sprayed Al2O3-TiO2 is still scarce. Consequently, it is crucial to study the effect of the suspension characteristics on the coating properties and to optimize the deposition process. In this work, Al2O3-13 wt.% TiO2 tribological coatings were successfully deposited by suspension plasma spraying from three different feedstocks: a nanometric suspension and two bimodal suspensions with different solid contents made up of titania nanoparticles and alumina submicron-sized particles. The coating microstructure and phase composition were characterized using scanning electron microscopy and X-ray diffraction analysis. Moreover, nanoindentation technique was used to determine the nanomechanical properties of coatings. The influence of the feed suspension characteristics on the final coating quality was analyzed. Findings showed that similar microstructures and phases were developed after depositing the different feedstocks. In addition suspension feedstock made up of nanoparticles resulted in a coating with better mechanical properties. However the use of submicron-sized particles in the suspension feedstocks gives rise to some technical and economic advantages in the process which should be taken into account when a suspension plasma spraying process is to be setup. (C) 2014 Elsevier B.V. All rights reserved., This work has been supported by the Spanish Ministry of Science and Innovation (project MAT2012-38364-C03) and it has been co-funded by ERDF (European Regional Development Funds).