Pasar al contenido principal

OBSERVADORES DE ESTADOS Y ENTRADAS BASADOS EN MODELOS MULTICUERPO DETALLADOS APLICADOS AL CONTROL DE VEHICULOS

BES-2015-071372

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Contratos Predoctorales
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDADE DA CORUÑA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

State, Parameter and Input Observers Based on Multibody Models and Kalman Filters for Vehicle Dynamics

  • Rodríguez, Antonio J.
  • Sanjurjo, Emilio
  • Pastorino, Roland
  • Naya, Miguel A.
Manuscrito aceptado, [Abstract] The aim of this work is to present a novel accurate estimator for vehicle dynamics. Following the multibody dynamics approach, a vehicle can be modeled with a high level of detail including non-linear dynamics. As a consequence, a rich simulation data-set is available for engineering analysis, richer than with vehicle analytical models. The proposed novel estimator is a new form of a dual Kalman filter. The first filter uses an indirect extended Kalman filter (i.e. the errorEKF) incorporating force estimation and using a vehicle multibody model. The second filter is an unscented Kalman filter (UKF) used to increase the accuracy of the errorEKF by estimating uncertain modeling parameters such as the mass of the vehicle and the tire-road friction coefficient. The performance of the proposed state-parameter-input (SPI) observer is tested in a simulation environment. The performance of the observer is demonstrated using two maneuvers, out of which one covers aggressive driving conditions. The results show that the new observer estimates with high accuracy the variables of interest for vehicle dynamics, such as the tire forces., This work has been partially financed by the Spanish Ministry of Economy and Competitiveness (MINECO) and EU-ERDF funds under the project ‘Observadores de estados y entradas basados en modelos multicuerpo detallados aplicados al control de vehículos’ (TRA2014-59435-P) and through the grant BES-2015-071372.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Hardware Acceleration of Multibody Simulations for Real-Time Embedded Applications

  • Rodríguez, Antonio J.
  • Pastorino, Roland
  • Carro Lagoa, Ángel
  • Janssens, Karl
  • Naya, Miguel A.
This version of the article has been accepted for publication, after peer review and is subject to Springer Nature’s AM terms of use [https://www.springernature.com/gp/open-science/policies/accepted-manuscript-terms], but is not the Version of Record and does not reflect postacceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/s11044-020-09738-w, [Abstract] New products in the automotive and aerospace industries must provide increased energy efficiency and exceed previous performance, safety and reliability. To meet these expectations, the role of simulation continues to grow. Within this context, simulation models are used in real-time embedded applications such as advanced real-time control and virtual sensing. Both applications require the execution of simulation models in real-time on embedded hardware. The limited computational power of this hardware is, however, a major challenge in the adoption of model-based embedded applications. This research explores the use of multibody models for real-time embedded applications. It describes different techniques to accelerate parts or all of the multibody computations on ARM-based and/or FPGA-based hardware., The support of the Spanish Ministry of Economy and Competitiveness (MINECO) under project TRA 2014-59435-P and through the grant BES-2015-071372, cofinanced by the European Union through the ERDF program, is greatly acknowledged.