Pasar al contenido principal

OBSERVADORES DE ESTADOS Y ENTRADAS BASADOS EN MODELOS MULTICUERPO DETALLADOS APLICADOS AL CONTROL DE VEHICULOS

TRA2014-59435-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2014
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDADE DA CORUÑA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Accuracy and Efficiency Comparison of Various Nonlinear Kalman Filters Applied to Multibody Models

  • Sanjurjo, Emilio
  • Naya, Miguel A.
  • Blanco Claraco, José Luis
  • Torres-Moreno, José Luis
  • Giménez, Antonio
This version of the article has been accepted for publication, after peer review and is subject to Springer Nature’s AM terms of use, but is not the Version of Record and does not reflect post-acceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/s11071-017-3354-z, [Abstract] Multibody simulations are already used in many industries to speed up the development of new products. However, improvements in multibody formulations and the continuous increase in inexpensive computational power open new fields of applications for multibody simulations, such as using them as plant models for state observers. The present work introduces a novel state observer developed by combining a multibody model with an indirect Kalman filter. Together with other multibody-based Kalman filters already proposed in the literature, they have been applied to two mechanisms (four- and five-bar linkages) to assess their performance. The accuracy of the estimations and the computational cost are examined under several scenarios: using position or velocity sensors in different configurations, with different sampling rates, and considering different levels of errors in the models assumed by the filters. The aim of this work is to present different options to build a state observer based on a dynamic multibody model, and to provide guidance to select the most suitable option for future applications. All the methods have been implemented as a reusable MATLAB toolkit which has been released as Open Source in https://github.com/MBDS/mbde-matlab., This work has been partially financed by the Spanish Ministry of Economy and Competitiveness and EU-ERDF funds under the projects ‘Observadores de estados y entradas basados en modelos multicuerpo detallados aplicados al control de vehículos’ (TRA2014-59435-P) and ‘ENERPRO’ (DPI2014-56364-C2-1-R). The research of Emilio Sanjurjo was funded by fellowship BES-2013-063598 of Spanish Government., https://github.com/MBDS/mbde-matlab
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

State, Parameter and Input Observers Based on Multibody Models and Kalman Filters for Vehicle Dynamics

  • Rodríguez, Antonio J.
  • Sanjurjo, Emilio
  • Pastorino, Roland
  • Naya, Miguel A.
Manuscrito aceptado, [Abstract] The aim of this work is to present a novel accurate estimator for vehicle dynamics. Following the multibody dynamics approach, a vehicle can be modeled with a high level of detail including non-linear dynamics. As a consequence, a rich simulation data-set is available for engineering analysis, richer than with vehicle analytical models. The proposed novel estimator is a new form of a dual Kalman filter. The first filter uses an indirect extended Kalman filter (i.e. the errorEKF) incorporating force estimation and using a vehicle multibody model. The second filter is an unscented Kalman filter (UKF) used to increase the accuracy of the errorEKF by estimating uncertain modeling parameters such as the mass of the vehicle and the tire-road friction coefficient. The performance of the proposed state-parameter-input (SPI) observer is tested in a simulation environment. The performance of the observer is demonstrated using two maneuvers, out of which one covers aggressive driving conditions. The results show that the new observer estimates with high accuracy the variables of interest for vehicle dynamics, such as the tire forces., This work has been partially financed by the Spanish Ministry of Economy and Competitiveness (MINECO) and EU-ERDF funds under the project ‘Observadores de estados y entradas basados en modelos multicuerpo detallados aplicados al control de vehículos’ (TRA2014-59435-P) and through the grant BES-2015-071372.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Online Kinematic and Dynamic-State Estimation for Constrained Multibody Systems Based on IMUs

  • Torres-Moreno, José Luis
  • Blanco Claraco, José Luis
  • Giménez, Antonio
  • Sanjurjo, Emilio
  • Naya, Miguel A.
[Abstract] This article addresses the problems of online estimations of kinematic and dynamic states of a mechanism from a sequence of noisy measurements. In particular, we focus on a planar four-bar linkage equipped with inertial measurement units (IMUs). Firstly, we describe how the position, velocity, and acceleration of all parts of the mechanism can be derived from IMU signals by means of multibody kinematics. Next, we propose the novel idea of integrating the generic multibody dynamic equations into two variants of Kalman filtering, i.e., the extended Kalman filter (EKF) and the unscented Kalman filter (UKF), in a way that enables us to handle closed-loop, constrained mechanisms, whose state space variables are not independent and would normally prevent the direct use of such estimators. The proposal in this work is to apply those estimators over the manifolds of allowed positions and velocities, by means of estimating a subset of independent coordinates only. The proposed techniques are experimentally validated on a testbed equipped with encoders as a means of establishing the ground-truth. Estimators are run online in real-time, a feature not matched by any previous procedure of those reported in the literature on multibody dynamics., Ministerio de Economía y Competitividad; DPI2011-22513
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Roll Angle Estimator Based on Angular Rate Measurements for Bicycles

  • Sanjurjo, Emilio
  • Naya, Miguel A.
  • Cuadrado, Javier
  • Schwab, Arend L.
This is an Accepted Manuscript version of the following article, accepted for publication in Vehicle System Dynamics: Sanjurjo, E., Naya, M. A., Cuadrado, J., & Schwab, A. L. (2018). Roll angle estimator based on angular rate measurements for bicycles. Vehicle System Dynamics, 57(11), 1705–1719. https://doi.org/10.1080/00423114.2018.1551554. It is deposited under the terms of the Creative Commons Attribution-NonCommercial License (http://creativecommons.org/licenses/by-nc/4.0/), which permits noncommercial re-use, distribution, and reproduction in any medium, provided the original work is properly cited., [Abstract] Measuring the roll angle of single-track vehicles has always been a challenging task; however, accurate and reliable measurements of this magnitude are paramount for controlling the stability of these vehicles, both for autonomous riding and for safety reasons. A roll angle estimation is also useful in other situations, such as tests to perform the identification of the parameters of the rider control. In this work, a new algorithm is presented for estimating the roll angle of bicycles. This estimator, based on the well-known Kalman filter, employs a wheel speed sensor to approximate the speed of the vehicle, and three angular rate sensors, which are currently small and affordable sensors. The proposed method was implemented in a microcontroller and tested in a bicycle and the results were compared with measurements obtained with optical sensors, showing a good correlation. Although it has not been tested in motorcycles, comparable results are expected., This work has been partially financed by the Ministerio de Economía y Competitividad and European Regional Development Fund funds under the project ‘Observadores de estados y entradas basados en modelos multicuerpo detallados aplicados al control de vehículos’ [TRA2014-59435-P], by the Xunta de Galicia [ED431B 2016/031], and by the European Commission under the MOTORIST (Motorcycle Rider Integrated Safety) project (ITN Nr. 608092), funded through the FP7 Marie Curie programme. The research of Emilio Sanjurjo was funded by the Spanish Ministry of Economy and Competitiveness under the fellowship BES-2013-063598 and the grant number EEBB-I-15-10331., Xunta de Galicia; ED431B 2016/031
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Hardware Acceleration of Multibody Simulations for Real-Time Embedded Applications

  • Rodríguez, Antonio J.
  • Pastorino, Roland
  • Carro Lagoa, Ángel
  • Janssens, Karl
  • Naya, Miguel A.
This version of the article has been accepted for publication, after peer review and is subject to Springer Nature’s AM terms of use [https://www.springernature.com/gp/open-science/policies/accepted-manuscript-terms], but is not the Version of Record and does not reflect postacceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/s11044-020-09738-w, [Abstract] New products in the automotive and aerospace industries must provide increased energy efficiency and exceed previous performance, safety and reliability. To meet these expectations, the role of simulation continues to grow. Within this context, simulation models are used in real-time embedded applications such as advanced real-time control and virtual sensing. Both applications require the execution of simulation models in real-time on embedded hardware. The limited computational power of this hardware is, however, a major challenge in the adoption of model-based embedded applications. This research explores the use of multibody models for real-time embedded applications. It describes different techniques to accelerate parts or all of the multibody computations on ARM-based and/or FPGA-based hardware., The support of the Spanish Ministry of Economy and Competitiveness (MINECO) under project TRA 2014-59435-P and through the grant BES-2015-071372, cofinanced by the European Union through the ERDF program, is greatly acknowledged.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

State and Force Observers Based on Multibody Models and the Indirect Kalman Filter

  • Sanjurjo, Emilio
  • Dopico, Daniel
  • Luaces, Alberto
  • Naya, Miguel A.
Accepted manuscript, [Abstract] The aim of this work is to present two new methods to provide state observers by combining multibody simulations with indirect extended Kalman filters. One of the methods presented provides also input force estimation. The observers have been applied to two mechanism with four different sensor configurations, and compared to other multibody-based observers found in the literature to evaluate their behavior, namely, the unscented Kalman filter (UKF), and the indirect extended Kalman filter with simplified Jacobians (errorEKF). The new methods have some more computational cost than the errorEKF, but still much less than the UKF. Regarding their accuracy, both are better than the errorEKF. The method with input force estimation outperforms also the UKF, while the method without force estimation achieves results almost identical to those of the UKF. All the methods have been implemented as a reusable MATLAB® toolkit which has been released as Open Source in https://github.com/MBDS/mbde-matlab., This work has been partially financed by the Spanish Ministry of Economy and Competitiveness (MINECO) and EU-ERDF funds under the projects ‘Observadores de estados y entradas basados en modelos multicuerpo detallados aplicados al control de vehículos’ (TRA2014-59435-P) and ‘Diseño y control óptimo eficiente de sistemas multicuerpo basado en técnicas de análisis de sensibilidad’ (DPI2016-81005-P), and by the Galician Government through grant ED431B2016/031., Xunta de Galicia; ED431B2016/031