Pasar al contenido principal

NUEVOS CONCEPTOS DE COMBUSTION PARA REDUCCION DE CONSUMO, CO2 Y EMISIONES CONTAMINANTES EN MOTORES DE GASOLINA PARA AUTOMOCION

BES-2016-077610

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Contratos Predoctorales
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of water direct injection in a CAI/HCCI gasoline engine to extend the operating range towards higher loads

  • Valero-Marco, Jorge
  • Lehrheuer, Bastian
  • Pischinger, Stefan
  • López, J. Javier|||0000-0002-9486-2511
[EN] CAI (Controlled AutoIgnition) systems, also named HCCI (Homogeneous Charge Compression Ignition), are a promising way to improve gasoline engines. This combustion mode is more efficient than the standard SI (Spark Ignition) combustion and, additionally, it has very low emissions, especially NOx emissions, which represent a source of problems nowadays. The main problem of this combustion mode is the constrained operating range, caused, on the one hand, by the difficulty to ignite the fuel since it has to be auto-ignited by the control of the mixture reactivity, and, on the other hand, by its high heat release rates, causing high pressure gradients and, in some circumstances, knocking combustion. In this paper, the possibility to use directly injected water into the combustion chamber as a reactivity suppressor in order to extend the constrained load range of CAI operation is evaluated. For this study, a four-stroke single-cylinder gasoline engine has been modified to allow CAI combustion by means of adapted valve trains enabling to keep hot residual gases inside the cylinder, which will provoke the fuel autoignition. Additionally, a water direct injection system has been installed in the engine to carry out this study. The results show that water injection is an efficient strategy to increase the maximum affordable load in CAI conditions, since the reactivity of the mixture can be suitably controlled, thus reducing the pressure gradients and the knocking tendency of the combustion process, also keeping good levels of combustion stability. Nevertheless, the engine has to be significantly boosted and the necessary intake pressure compared to a conventional SI operation mode in stoichiometric conditions is much higher., The research was performed as part of the Research Unit (Forschergruppe) FOR 2401 "Optimization based Multiscale Control for Low Temperature Combustion Engines", which is funded by the German Research Association (Deutsche Forschungsgemeinschaft, DFG). The support is gratefully acknowledged. The authors would like to thank also different members of the VKA institute for combustion engines of the RWTH Aachen university and CMT-Motores Termicos team of the Universitat Politecnica de Valencia for their contribution to this work and also thank the Universitat Politecnica de Valencia (contract 3102) and the Spanish Ministry of Economy and Competitiveness (contract BES-2016-077610) for financing the PhD. studies of Jorge Valero-Marco, partly funded by FEDER and the Spanish Government through project TRA2015-67136-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Characterization of the turbulent flame front surface in spark ignition engines during spark ignition operation to identify controlled auto-ignition and abnormal combustion

  • Macian Martinez, Vicente
  • Valero-Marco, Jorge
  • López, J. Javier|||0000-0002-9486-2511
  • Martín, Jaime|||0000-0002-0496-3176
[EN] The combustion diagnostics and subsequent analysis are standardized tools based on the estimation of the heat release law (HRL). From this estimation, the different combustion parameters can be obtained: combustion phasing and duration, heat release rate, and so on. This analysis might be usually enough to study traditional spark ignition (SI) engines. However, with the new upcoming SI engines, this is probably not the case anymore, since different combustion modes can be operated in the same engine, as for instance a combination of SI and controlled auto-ignition (CAI) combustion modes. When different combustion modes are combined, it seems interesting to study in more depth the HRL, trying to get more data and to study the differences among the diverse combustion modes. Toward this end, a methodology to go deeper in the study of the HRL is proposed in this work, consisting of, mainly quantifying and taking into account the most relevant influencing parameters: the fuel properties (mainly its lower heating value), the in-cylinder oxygen content, the density of the burned and unburned zones, the laminar combustion speed, and the turbulence effect. With the proposed methodology, a standard SI combustion, developed by a flame front, can be characterized at any given operating point. This would allow to predict which the combustion developement would be, at this operating point, assuming it to be developed by a flame front. Subsequently, this SI combustion prediction can be compared to the one obtained experimentally, making it possible to identify and analyze abnormal combustion phenomena, as well as to study the differences between a combustion developed by a flame front (SI) and by auto-ignition (CAI). Derived from this work, an alternative equation to experimentally characterize the laminar combustion velocity has also been proposed, in order to improve its applicability in a wider range of fuel/air ratios and dilution degrees., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: the Spanish Ministry of Science, Innovation and Universities for funding the PhD. studies of Jorge Valero-Marco (contract BES-2016-077610). This work was partly funded by Renault, and by FEDER and the Spanish Government through project TRA2015-67136-R.