Pasar al contenido principal

NUEVOS CONCEPTOS DE COMBUSTION PARA REDUCCION DE CONSUMO, CO2 Y EMISIONES CONTAMINANTES EN MOTORES DE GASOLINA PARA AUTOMOCION

TRA2015-67136-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of water direct injection in a CAI/HCCI gasoline engine to extend the operating range towards higher loads

  • Valero-Marco, Jorge
  • Lehrheuer, Bastian
  • Pischinger, Stefan
  • López, J. Javier|||0000-0002-9486-2511
[EN] CAI (Controlled AutoIgnition) systems, also named HCCI (Homogeneous Charge Compression Ignition), are a promising way to improve gasoline engines. This combustion mode is more efficient than the standard SI (Spark Ignition) combustion and, additionally, it has very low emissions, especially NOx emissions, which represent a source of problems nowadays. The main problem of this combustion mode is the constrained operating range, caused, on the one hand, by the difficulty to ignite the fuel since it has to be auto-ignited by the control of the mixture reactivity, and, on the other hand, by its high heat release rates, causing high pressure gradients and, in some circumstances, knocking combustion. In this paper, the possibility to use directly injected water into the combustion chamber as a reactivity suppressor in order to extend the constrained load range of CAI operation is evaluated. For this study, a four-stroke single-cylinder gasoline engine has been modified to allow CAI combustion by means of adapted valve trains enabling to keep hot residual gases inside the cylinder, which will provoke the fuel autoignition. Additionally, a water direct injection system has been installed in the engine to carry out this study. The results show that water injection is an efficient strategy to increase the maximum affordable load in CAI conditions, since the reactivity of the mixture can be suitably controlled, thus reducing the pressure gradients and the knocking tendency of the combustion process, also keeping good levels of combustion stability. Nevertheless, the engine has to be significantly boosted and the necessary intake pressure compared to a conventional SI operation mode in stoichiometric conditions is much higher., The research was performed as part of the Research Unit (Forschergruppe) FOR 2401 "Optimization based Multiscale Control for Low Temperature Combustion Engines", which is funded by the German Research Association (Deutsche Forschungsgemeinschaft, DFG). The support is gratefully acknowledged. The authors would like to thank also different members of the VKA institute for combustion engines of the RWTH Aachen university and CMT-Motores Termicos team of the Universitat Politecnica de Valencia for their contribution to this work and also thank the Universitat Politecnica de Valencia (contract 3102) and the Spanish Ministry of Economy and Competitiveness (contract BES-2016-077610) for financing the PhD. studies of Jorge Valero-Marco, partly funded by FEDER and the Spanish Government through project TRA2015-67136-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Correlations for the ignition characteristics of six different fuels and their application to predict ignition delays under transient thermodynami conditions

  • Desantes J.M.|||0000-0002-4124-9393
  • Bermúdez, Vicente|||0000-0002-2781-5598
  • López, J. Javier|||0000-0002-9486-2511
  • López-Pintor, Darío
[EN] The ignition characteristics of six different fuels have been correlated as a function of the temperature, pressure, equivalence ratio and oxygen molar fraction in this investigation. More specifically, the ignition delay referred to cool flames, the high-temperature ignition delay and the critical concentrations and ignition times of HO2 and CH2O have been parameterized for n-dodecane, PRFO, PRF25, PRF50, PRF75 and PRF100. To do so, a wide database of ignition data of the aforementioned fuels has been generated by means of chemical simulations in CHEMKIN, solving a detailed mechanism for PRF mixtures and a reduced mechanism for n-dodecane. In fact, in cylinder engine-like conditions reached in a Rapid Compression Expansion Machine (RCEM) have been replicated. The mathematical correlations have shown a relative deviation around 20% with the database in the low-temperature, low-pressure zone, which is the typical accuracy of usual correlations for the ignition delay. Finally, the ignition delay under transient conditions measured in the RCEM has been predicted by means of different integral methods coupled to both the proposed correlations and the generated database. It has been found that deviations between the predictions obtained with the correlations or with the database are lower than 1%. This means that the correlations are accurate enough to predict the ignition time in spite of showing high deviation with the database, since the low-temperature, low-pressure zone has a minor contribution to the ignition delay., The authors would like to thank different members of the CMT-Motores Termicos team of the Universitat Politecnica de Valencia for their contribution to this work. The authors would also like to thank the Spanish Ministry of Education for financing the PhD. Studies of Dario Lopez-Pintor (grant FPU13/02329). This research has been partially funded by FEDER and the Spanish Government through project TRA2015-67136-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A phenomenological explanation of the autoignition propagation under HCCI conditions

  • Desantes J.M.|||0000-0002-4124-9393
  • López, J. Javier|||0000-0002-9486-2511
  • García-Oliver, José M|||0000-0002-2676-9681
  • López-Pintor, Darío
[EN] A phenomenological explanation about the autoignition propagation under HCCI conditions is developed in this paper. To do so, diffusive effects from the burned zones to the fresh mixture, pressure waves based effects and expansion effects caused by combustion are taken into account. Additionally, different Damkohler numbers have been defined and evaluated in order to characterize the phenomenon and quantify the relevance of each effect. The theoretical explanation has been evaluated by means of chemiluminescence measurements performed in a Rapid Compression Expansion Machine (RCEM), which allow to estimate the velocity of propagation of the autoignition front. The results showed that under HCCI conditions the autoignition propagation is controlled, in general, by the pressure waves established in the combustion chamber, since the characteristic time of the autoignition propagation is too short to assume the absence of pressure gradients in the chamber. Thus, the thermodynamic conditions reached behind the pressure wave promote the autoignition and explain the high propagation velocities associated to the reaction front. Besides, the results also showed that the contribution of diffusive phenomena on the propagation is negligible, since the characteristic time of diffusion is too long compared to the characteristic time of the autoignition propagation. Finally, the experimental measurements showed that the autoignition propagation is affected by a really relevant cycle-to-cycle variation. The turbulence generated by the combustion has, by definition, an aleatory behavior, leading to random heterogeneity distribution and, therefore, to somewhat random autoignition propagation., The authors would like to thank different members of the CMT-Motores TTrmicos team of the Universitat Politecnica de Valencia for their contribution to this work. The authors would also like to thank the Spanish Ministry of Education for financing the PhD. Studies of Dario Lopez-Pintor (grant FPU13/02329). This research has been partially funded by FEDER and the Spanish Government through project TRA2015-67136-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental validation of an alternative method to predict high and low-temperature ignition delays under transient thermodynamic conditions for PRF mixtures using a Rapid Compression-Expansion Machine

  • Desantes J.M.|||0000-0002-4124-9393
  • Bermúdez, Vicente|||0000-0002-2781-5598
  • López, J. Javier|||0000-0002-9486-2511
  • López Pintor, Darío
An alternative procedure to predict both high-temperature stage and cool flames ignition delays under transient thermodynamic conditions is intended to be validated in this paper. An experimental study has been carried out in a Rapid Compression-Expansion Machine (RCEM), using different iso-octane/nheptane blends in order to cover a wide range of octane numbers (from 25 to 75) under a wide range of initial temperatures (from 363 K to 423 K), compression ratios (14 and 19), O2 molar rates (from 21% to 16%) and equivalence ratios (from 0.4 to 0.8). The results obtained have been used to validate direct chemical kinetic simulations, as well as to evaluate the alternative predictive method and the Livengood & Wu integral method. Simulations have been performed solving a detailed chemical kinetic mechanism in CHEMKIN. The experimental results show good agreement with the chemical kinetic simulations and with the alternative predictive method. In fact, the mean relative deviation between experiments and simulations is equal to 1.7%, 2.2% and 3.1% for PRF25, PRF50 and PRF75, respectively. Besides, the alternative method has shown good predictive capability not only for the high-temperature stage of the process, but also for cool flames, being the mean relative deviation versus the experimental data lower than 3.3% for all fuels. Better predictions of the ignition delay have been obtained with the alternative procedure than the ones obtained with the classic Livengood & Wu expression, especially in those cases showing a two-stage ignition pattern, in which the Livengood & Wu integral method is not able to predict the high-temperature stage of the process., The authors would like to thank different members of the CMT-Motores Termicos team of the Universitat Politecnica de Valencia for their contribution to this work. The authors would also like to thank the Spanish Ministry of Education for financing the PhD. Studies of Dario Lopez-Pintor (Grant FPU13/02329). This work was partly funded by the Spanish Ministry of Economy and Competitiveness, project TRA2015-67136-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the potential of a new automotive two-stroke gasoline engine able to operate in spark ignition and controlled autoignition combustion modes

  • López, J. Javier|||0000-0002-9486-2511
  • Molina, Santiago|||0000-0001-7879-2421
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Valero-Marco, Jorge
  • Justet, F.
[EN] The need to reduce the emissions coming from automobiles encourages the attempts to study different engine configurations and new combustion strategies. In this case, a two stroke engine able to operate in Controlled Autolgnition (CAI) and Spark Ignition (SI) combustion modes is studied, with the purpose of getting lower NO and CO2 emissions than with other currently employed solutions. The engine configuration retained for the research is a uniflow scavenging configuration with intake ports in the cylinder liner and exhaust valves in the cylinder head. These valves are controlled by a Variable Valve Timing (VVT) system. The scavenging is guaranteed by an external blower driven by the crankshaft. Finally, the fuel supply is performed by a direct injection (DI) air-assisted fuel injection system. Through this paper the adjusting parameters to control the engine operation, as well as their influence on the CAI and SI combustion modes have been studied, providing the most relevant information and knowledge for controlling and optimizing the engine performance. Once these controlling parameters were studied, an EGR system was introduced in order to analyze the effect of this other parameter over the combustion process, as well as to determine the potential benefits of introducing such a system in this type of engines. (C) 2017 Elsevier Ltd. All rights reserved., The authors would like to thank different members of the CMTMotores Termicos team of the Universitat Politecnica de Valencia for their contribution to this work. The authors would also like to thank the Universitat Politecnica de Valencia for financing the PhD. studies of Jorge Valero-Marco (contract 3102). This work was partly funded by Renault S.A.S., the contribution of which is greatly acknowledged, and by FEDER and the Spanish Government through project TRA2015-67136-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Characterization of the turbulent flame front surface in spark ignition engines during spark ignition operation to identify controlled auto-ignition and abnormal combustion

  • Macian Martinez, Vicente
  • Valero-Marco, Jorge
  • López, J. Javier|||0000-0002-9486-2511
  • Martín, Jaime|||0000-0002-0496-3176
[EN] The combustion diagnostics and subsequent analysis are standardized tools based on the estimation of the heat release law (HRL). From this estimation, the different combustion parameters can be obtained: combustion phasing and duration, heat release rate, and so on. This analysis might be usually enough to study traditional spark ignition (SI) engines. However, with the new upcoming SI engines, this is probably not the case anymore, since different combustion modes can be operated in the same engine, as for instance a combination of SI and controlled auto-ignition (CAI) combustion modes. When different combustion modes are combined, it seems interesting to study in more depth the HRL, trying to get more data and to study the differences among the diverse combustion modes. Toward this end, a methodology to go deeper in the study of the HRL is proposed in this work, consisting of, mainly quantifying and taking into account the most relevant influencing parameters: the fuel properties (mainly its lower heating value), the in-cylinder oxygen content, the density of the burned and unburned zones, the laminar combustion speed, and the turbulence effect. With the proposed methodology, a standard SI combustion, developed by a flame front, can be characterized at any given operating point. This would allow to predict which the combustion developement would be, at this operating point, assuming it to be developed by a flame front. Subsequently, this SI combustion prediction can be compared to the one obtained experimentally, making it possible to identify and analyze abnormal combustion phenomena, as well as to study the differences between a combustion developed by a flame front (SI) and by auto-ignition (CAI). Derived from this work, an alternative equation to experimentally characterize the laminar combustion velocity has also been proposed, in order to improve its applicability in a wider range of fuel/air ratios and dilution degrees., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: the Spanish Ministry of Science, Innovation and Universities for funding the PhD. studies of Jorge Valero-Marco (contract BES-2016-077610). This work was partly funded by Renault, and by FEDER and the Spanish Government through project TRA2015-67136-R.