Pasar al contenido principal

ESTUDIO EXPERIMENTAL Y NUMERICO DE NUDOS VIGA-SOPORTE Y LOSA-SOPORTE EN PILARES DE HA REFORZADOS

BIA2008-06268

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2008
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Finite element modelling of steel-caged RC columns subjected to axial force and bending moment

  • Garzón Roca, Julio
  • Valente, Isabel B.
  • Adam, Jose M|||0000-0002-9205-8458
  • Calderón García, Pedro Antonio|||0000-0002-9783-9333
Steel caging is an effective, economical, easily applied and widely used method of strengthening RC columns. Based on the results of two experimental studies, this paper proposes the finite element modelling of RC columns strengthened by a steel cage under axial loads and bending moments. The FE models were used to obtain the N-M diagrams of experimental cases in which a study was made of the improved resistance of RC columns strengthened with this type of strengthening technique. The paper also includes a comparison of different methods of connecting the cage around the beam-column joint and a parametric study to observe the influence of diverse parameters on the behaviour of the strengthened column, including: angle dimensions, number of strips, the yield stress of the steel used in the strengthening, the dimensions of the capitals at both ends of the column, concrete strength and the characteristics of the reinforcement used in the columns. Finally, the results of the various tests (experimental and numerical) described in the paper are used to be compared with three design proposals and the goodness of fit of each one is analysed. © 2012 Elsevier Ltd., Mr. Garzon-Roca is grateful to the Generalitat Valenciana and to the Universitat Politecnica de Valencia for the scholarship he was awarded to complete his doctorate studies and also to the Universidade do Minho, where he spent a stay of 6 months. Special thanks are due to Dr. Isabel Valente for her support in this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

RC columns strengthened by steel caging: Cyclic loading tests on beam-column joints with non-ductile details

  • Ruiz-Pinilla, Joaquin G.
  • Cladera, Antoni
  • Pallarés Rubio, Francisco Javier|||0000-0003-4298-2287
  • Calderón García, Pedro Antonio|||0000-0002-9783-9333
  • Adam, Jose M|||0000-0002-9205-8458
[EN] Beam-column joints suffer intense damage from seismic events and are the cause of many buildings collapsing. These zones present complex behaviour under cyclic loads, including tensile-compression cycles, which make reinforcement adherence worse and cause severe cracking in concrete. Although columns can be strengthened by various methods (e.g. concrete jacketing, fibre-reinforced polymers and steel jacketing-caging), beam column joints require complex systems being applied, but are not always effective. In Europe, fitting steel caging around columns is one of the most frequently used techniques, although its effectiveness against seismic events requires further study. The aim of this work is to analyse the behaviour of beam-column joints strengthened by steel caging subjected to cyclic loading, for which an ambitious experimental campaign was carried out on seven fullscale steel-caged specimens with a variety of strengthening solutions at joints. The results provide insight into the complex behaviour of joints with columns strengthened in this way, used as the basis for practical recommendations for engineers and architects who have to routinely retrofit structures against seismic events., The authors wish to express their gratitude for the financial support provided by the Spanish Ministry of Science and Innovation and the Spanish Ministry of Economy and Competitiveness with Research Projects BIA 2008-06268 and RTI2018-099091-B-C22
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental tests on retrofitted RC beam-column joints underdesigned to seismic loads. General approach

  • Ruiz Pinilla, Joaquín Guillermo
  • Pallarés Rubio, Francisco Javier|||0000-0003-4298-2287
  • Gimenez-Carbo, Ester|||0000-0002-2856-4081
  • Calderón García, Pedro Antonio|||0000-0002-9783-9333
This paper presents an experimental program designed to determine the behaviour of steel jacketing used as a seismic strengthening system for reinforced concrete frame structures. Tests were carried out on a total of 20 full scale interior beam-column joints. Geometry and reinforcements were selected according to existing buildings, designed solely to gravity loads under strong beam-weak column concept. Column strengthening was performed in all specimens, and four different types of column-joint connection strengthening have been tested. Two types of beam reinforcement have been included in the experimental program. Tests were carried out by subjecting specimens to gravity and cyclic loads. The paper shows general results and conclusions, describing the failure modes of the specimens. Results show that the strengthening techniques and the axial loads applied on columns can have significant influence on the seismic behaviour of the joints. (C) 2013 Elsevier Ltd. All rights reserved., The authors wish to express their gratitude for the financial support received from the Spanish Ministry of Science and Innovation under Research Project BIA 2008-06268.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An experimental study on steel caged RC columns subjected to axial force and bending moment

  • Garzón Roca, Julio
  • Ruiz Pinilla, Joaquín Guillermo
  • Adam, Jose M|||0000-0002-9205-8458
  • Calderón García, Pedro Antonio|||0000-0002-9783-9333
Among the different methods of strengthening RC columns, steel caging is one of the most extensively used, for square or rectangular cross-section columns. Few studies have been carried out on steel caging and most of these have focused on axially loaded strengthened columns, without taking the effects of bending moments into account. This paper presents the results of a series of experimental tests on full-scale specimens strengthened with steel caging including simulation of the beam column joint under combined bending and axial loads. Capitals were applied to all the specimens to connect the caging with the beam column joint either by chemical anchors or steel bars to improve the transmission of forces. In all the specimens tested it was observed that steel caging increases both the ultimate load and ductility of the strengthened columns. The specimens fitted with steel bars reach higher ductility and strength than those with chemical anchors. The laboratory results were compared with three design proposals and the degree of fit with each one was analysed. (C) 2010 Elsevier Ltd. All rights reserved., The authors wish to express their gratitude for the financial support received from the Spanish Ministry of Science and Innovation under Research Project BIA 2008-06268. Also to the Generalitat Valenciana for its financial support within the GVPRE/2008/153 Project. Mr. Garzon-Roca is grateful to the Generalitat Valenciana for the scholarship awarded to him to complete his doctorate studies.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Joint strengthening by external bars on RC beam-column joints

  • Ruiz Pinilla, Joaquín G.
  • Cladera, Antoni
  • Pallarés Rubio, Francisco Javier|||0000-0003-4298-2287
  • Calderón García, Pedro Antonio|||0000-0002-9783-9333
  • Adam, Jose M|||0000-0002-9205-8458
[EN] Column strengthening is a very common practice for improving the seismic performance of reinforced concrete frame structures or repairing damage after a seismic event. Several methods are employed for column strengthening, which can improve column strength by preventing its shear, bending or compression failure. However, not all methods allow column strengthening connections between adjacent floors, thus the beam-column joint strength could be limited by the column-joint interface capacity. This work aimed to analyse two joint strengthening designs, for which an experimental campaign of eight full-scale beam-column joints strengthened with steel caging, and subjected to cyclic and gravity loads, was carried out. As access to joint panels is very complex in existing structures, joint strengthening consists of external solutions: vertical or diagonal bars and capitals connecting columns. The results showed that these techniques significantly increased beam-column joint strength and highlighted that failure can be undesirably transferred to the joint. Vertical bars prevented the bending failure of the column-joint interface, but failure occurred at the joint in this study. Diagonal bars can also prevent joint failure., The authors wish to thank the financial support provided by the Spanish Ministry of Science and Innovation and the Spanish Ministry of Economy and Competitiveness with Research Projects BIA 2008-06268 and RTI2018-099091-B-C22.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bearing capacity of steel-caged RC columns under combined bending and axial loads: Estimation based on Artificial Neural Networks

  • Jørgensen, Caroline
  • Grastveit, Ragnhild
  • Garzón Roca, Julio
  • Paya-Zaforteza, I.
  • Adam, Jose M|||0000-0002-9205-8458
The use of steel caging for strengthening a reinforced concrete (RC) column is an economical and common solution. However, the design of the optimum steel cage is a complex task. Artificial Neural Networks (ANN) has shown to be a useful device for engineers to solve tasks related to the modelling and prediction of the behavior of complex engineering problems. This mathematical tool can be trained from a series of inputs in order to obtain a desired output, without the need to reproduce the phenomenon under study. Based on a total of 950 results obtained with a validated finite element (FE) model, this paper presents the use of ANN to predict the axial-bending moment (N-M) interaction diagram of steel-caged RC columns under combined bending and axial loads. The data is arranged in a format of six input parameters taking into account several aspects such as the geometry of the RC column, the size of the steel cage, the concrete compressive strength, the steel yield stress and the axial load level. The output is the bending moment reached by the steel-caged RC column. Since the way of solving the beam-column joint plays a key role in the behavior of the strengthened column, four ANNs are developed in this paper, related to the beam-column connection type: using capitals, using capitals with chemical anchors, using capitals and steel bars, and without any element. The ANNs developed show excellent results, which are far better to those given by three design analytical proposals. Based on the ANNs performed, a simple mathematical expression is developed, which can be used by practitioners when facing the design of a steel-caged RC column subjected to axial loads and bending moments. (C) 2013 Elsevier Ltd. All rights reserved., The authors wish to express their gratitude for the financial support received from the Spanish Ministry of Science and Innovation under Research Project BIA 2008-06268. Also to the Generalitat Valenciana for its financial support within the GVPRE/2008/153 Project. Mr. Garzon-Roca is grateful to the Generalitat Valenciana and to the Universitat Politecnica de Valencia for the scholarship he was awarded to complete his doctorate studies. Special thanks are due to Professor Pedro A. Calderon for his support in this research.