Pasar al contenido principal

PREDICCION DEL AISLAMIENTO ACUSTICO EN LA EDIFICACION: PARTICIONES LIGERAS Y NUEVOS MATERIALES

BIA2010-17723

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2010
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical Evaluation of the Vibration Reduction Index for Structural Joints

  • Ramis Soriano, Jaime
  • Segovia, Enrique
  • Carbajo San Martín, Jesús
  • Godinho, Luis
  • Alba, Jesus|||0000-0002-4188-854X
The present paper addresses the analysis of structural vibration transmission in the presence of structural joints. The problem is tackled from a numerical point of view, analyzing some scenarios by using finite element models. The numerical results obtained making use of this process are then compared with those evaluated using the EN 12354 standard vibration reduction index concept. It is shown that, even for the simplest cases, the behavior of a structural joint is complex and evidences the frequency dependence. Comparison with results obtained by empirical formulas reveals that those of the standards cannot accurately reproduce the expected behavior, and thus indicate that alternative complementary calculation procedures are required. A simple methodology to estimate the difference between numerical and standard predictions is here proposed allowing the calculation of an adaptation term that makes both approaches converge. This term was found to be solution-dependent, and thus should be evaluated for each structure., This paper represents an improvement and expansion of a paper presented at the 42th CONGRESS OF ACOUSTIC-TECNIACUSTICA (R) 2011, Iberian Meeting on Acoustics and European Symposium on Environmental Acoustics and Sustainable Building Acoustics, organized by the Sociedad Espanola de Acustica (SEA), the Acoustics Laboratory of the University of Extremadura, and the Sociedade Portuguesa de Acustica (SPA), and with the support of the European Acoustics Association (EAA) and the International Commission for Acoustics (ICA).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Propuesta de Fórmula Empírica para el Factor de Pérdidas

  • del Rey, Romina|||0000-0001-5907-0677
  • Alba, Jesus|||0000-0002-4188-854X
  • Juliá Sanchis, Ernesto|||0000-0003-2940-3906
  • Segura Alcaraz, Jorge Gabriel|||0000-0001-8296-3609
  • Ramis Soriano, Jaime
[EN] Noise transmitted by the sidewalls of buildings is essential to study the overall airborne sound insulation. For the determination of the lateral transmissions we must determine a parameter known as vibration reduction index. To obtain the value of the vibration reduction index to know the acoustic behaviour of the whole constructive, it is necessary to know the velocity level difference and the structural reverberation time. The indeterminations in the velocity level difference, or in the structural reverberation time will add diversions in the global determination of the isolation of the whole constructive. In the Standard UNE EN 12354-1:2000 there are empirical expressions for obtained the structural reverberation time. In the Standard UNE-EN ISO 10848-1:2007 there is a detailed procedure to determine experimentally the velocity level difference and the structural reverberation time, and to know the sidewalls transmissions. In this work, it is compared the structural reverberation time obtained by empirical expression and the structural reverberation time obtained experimentally, applying the normalized procedure. Based on this comparison we readjusted the empirical equations with a fundamental parameter; the loss factor. It is observed that the estimates do not reflect reality if we consider the same loss factor for all the structural elements, as it is allowed in the predictions of UNE EN 12354. © 2011 CIMNE (Universitat Politècnica de Catalunya). Published by Elsevier España, S.L. All rights reserved., [ES] La evaluación del ruido transmitido por flancos en edificación es esencial para el estudio del aislamiento a ruido aéreo. Desde el punto de vista numérico, para la determinación de las transmisiones laterales es necesario conocer un parámetro conocido como índice de reducción vibracional. Para obtener este parámetro con el objetivo de conocer el comportamiento acústico de todo el conjunto constructivo, es necesario conocer la diferencia de niveles de velocidad y el tiempo de reverberación estructural. Indeterminaciones bien en la diferencia de niveles de velocidad, bien en el tiempo de reverberación estructural supondrán desviaciones en la determinación del aislamiento global de todo el conjunto constructivo. Existen normativas (UNE EN 12354-1:2000) que ofrecen expresiones empíricas para obtener el tiempo de reverberación estructural. Otras (UNE-EN ISO 10848-1:2007) ofrecen un procedimiento detallado para determinar experimentalmente la diferencia de niveles de velocidad y el tiempo de reverberación estructural, y así poder conocer las transmisiones por flancos. En este trabajo se compara el tiempo de reverberación estructural que se obtiene mediante las expresiones empíricas con el tiempo de reverberación estructural que se obtiene experimentalmente, aplicando el procedimiento de medida normalizado. Basándonos en estas comparaciones se reajustan las ecuaciones empíricas con un parámetro fundamental: el factor de pérdidas. Se observa que las estimaciones no reflejan la realidad si tenemos en cuenta el mismo factor de pérdidas para todos los distintos elementos estructurales, tal y como se permite en las predicciones de la UNE EN 12354. © 2011 CIMNE (Universitat Politècnica de Catalunya). Publicado por Elsevier España, S.L. Todos los derechos reservados., Este trabajo ha sido financiado por el Ministerio de Educación y Ciencia (BIA2007-68098-C02-01 y BIA2007-68098-C02-02) y por el Ministerio de Ciencia e Innovación (BIA2010-17723).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An empirical modelling of porous sound absorbing materials made of recycled foam

  • del Rey, Romina|||0000-0001-5907-0677
  • Alba, Jesus|||0000-0002-4188-854X
  • Arenas, Jorge P.
  • Sanchis Rico, Vicente Jorge
Polyurethane foam waste is one of the residues of the manufacturing processes in textile industry, the disposal of which is becoming a severe environmental problem. In this paper the sound absorption properties of different materials developed from ground polyurethane foam waste are studied. Because these recycled materials exhibit good sound absorbing properties they are viable alternatives to conventional materials for practical applications. Experimental measures have been carried out to determine the characteristic wave impedance and propagation constant of these materials. Modelling of the acoustic behaviour has been done using the Dunn and Davern model and Voronina model. The first model presents deviations in the results so the experimental results have been used to report corrections to the empirical model. The Voronina model has been applied to verify that it serves to model the behaviour of these kinds of recycled materials. Both models converge and present acceptable results., This work has been supported by the Ministerio de Ciencia e Innovacion (BIA2010-17723), the Inter-University and Scientific Cooperation Program of AECID (A/023748/09) and Conicyt-Fonde-cyt under Grant No. 1110605.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Caracterización de vidrios para la evaluación del aislamiento acústico a ruido aéreo, Glass characterization to assess the airborne sound isolation

  • Alba Fernández, Jesús
  • Rey Tormos, Romina del
  • Ramis-Soriano, Jaime
  • Bertó Carbó, Laura
  • Ramis-Soriano, Jaime|||/items/f66772ed-9a3f-4478-91a1-1b3babaf0876
La principal aportación del trabajo es la formulación de una alternativa que facilita la determinación experimental del factor de pérdidas y, en consecuencia, mejorar las predicciones de aislamiento a ruido aéreo para vidrios con una o más capas intermedias sea cual fuere su naturaleza. Además, se realiza una revisión de las normativas relacionadas con los ensayos de los parámetros mecánicos necesarios para la caracterizar los vidrios, centrándonos en los monolíticos y los laminados. En efecto, uno de los problemas que se plantea en el contexto de la acústica de la edificación actualmente es el de cumplir con los requisitos de aislamiento acústico a ruido aéreo en fachada que exige el vigente Código Técnico de la Edificación (CTE). Como sabemos, en la fachada podemos distinguir la parte ciega y la parte hueca. La parte más débil en lo concerniente a aislamiento a ruido aéreo es la hueca (compuesta por el vidrio, carpintería y otros elementos). Si la carpintería es la adecuada, la superficie de vidrio se convierte en el elemento limitante. El Catálogo de Elementos Constructivos (CEC) del CTE, la propia norma UNE-EN 12758:2011, así como algunos, cada vez más, fabricantes ofrecen datos del aislamiento de vidrios simples, vidrios laminados y vidrios dobles. En el caso de vidrios laminados, estos datos se limitan únicamente en los que tienen un sola lámina intermedia y, además, no acústicos. Podemos hablar, por tanto, de una laguna de información en este sentido. Para obtener predicciones fiables de aislamiento acústico a ruido aéreo de particiones multicapa, como pueden ser los vidrios laminados es necesario disponer de las características mecánicas y una de las más relevantes es el factor de pérdidas.