Pasar al contenido principal

PROYECTO BASADO EN PRESTACIONES DE ESTRUCTURAS DE HORMIGON PARCIALMENTE PRETENSADAS. PROPUESTA DE NUEVA METODOLOGIA, VERIFICACION EXPERIMENTAL Y CRITERIOS DE PROYECTO.

BIA2012-36848

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2012
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Secretaría de Estado de Investigación, Desarrollo e Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Shear crack pattern identification in concrete elements via distributed optical fibre grid

  • Rodríguez Gutiérrez, Gerardo
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
  • Villalba Herrero, Sergi|||0000-0001-6535-6372
This is an Accepted Manuscript of an article published by Taylor & Francis Group in "Structure and infrastructure engineering: maintenance, management, life-cycle design and performance" on 2019, available online at: http://www.tandfonline.com/10.1080/15732479.2019.1640256, An experimental methodology to obtain the shear cracking pattern in concrete elements is presented. The method is based on the use of Distributed Optical Fiber Sensors (DOFS) connected to an Optical Backscattered Reflectometer (OBR). Using this OBR system and a 2D grid conformed by one or two DOFS, the crack patterns of three partially pre-stressed concrete (PPC) beams subjected experimentally to shear failure, were obtained for increasing level of load. The 2D distributed fiber optic sensoring mesh was formed by attaching the fiber to the shear span of each beam using an epoxy adhesive. The importance of a correct DOFS attaching procedure to the concrete surface to obtain accurate results is described, and the principal advantages of DOFS to complement the use of discrete sensors in concrete experimental shear tests are shown. The proposed technique is a powerful tool to be implemented in the structural health monitoring in shear of concrete structures, where the variable inclined cracks are difficult to monitor by other experimental techniques using discrete sensors., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical simulation since early ages of the RG8 beam test from concrack benchmark by means of a 3D fibre frame model

  • Crespo Garibay, María Delia
  • Ferreira, Denise
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
This work presents the numerical analysis of the RG8 test performed by the French research program Concrack2 in 2011. It consisted in a large RC beam specimen loaded in bending after restrained shrinkage. The specimen is composed of a central thinner part and two massive heads linked by two cylindrical struts that restrained strains due to thermal effects and autogenous shrinkage occurring in the concrete central part. After 8 weeks, the beam was loaded near to its ultimate capacity. The numerical model is based on the 3D fibre beam approach, capable of reproducing the response since early ages. The cross-section is discretized into fibres to take into account the different maturity levels within the crosssection. The analysis is divided into three phases: i) the thermal analysis determines the development of temperatures due to cement hydration and heat transfer, solar radiation and night cooling effects, ii) nonlinear mechanical analysis for early ages including creep, autogenous shrinkage and ageing and iii) nonlinear mechanical analysis for loading phase includes the interaction of normal and shear forces. Performance is compared against experimentation and the development of early age stresses discussed.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Crack detection in concrete elements from RGB pictures using modified line detection kernels

  • Sánchez Calderón, Luis
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
Cracking is inevitable in ordinary reinforced concrete construction, yet it should be controlled to guarantee adequate serviceability and durability. Crack patterns analysis is essential for diagnosis, monitoring and maintenance, to identify malfunctioning or unsafe situations. An important part of this state is the cracking pattern of the elements as an indicator of the tensional distribution in the concrete. A method to search and measure fissures in RGB images of concrete elements has been developed and implemented as a MATLAB script. The algorithm uses several digital image processing tools to detect the measure, the cracks width and orientation; featuring these tools are the spatial filters called “orientation kernels” developed especially for detecting the angle and width of the cracks.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A new concrete plastic-damage model with an evolutive dilatancy parameter

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
Typical plastic-damage models for concrete use a constant dilatancy parameter. On problems sensitive to confinement and shear softening, this parameter needs ad hoc calibration to fit experimental observations. This makes the model not objective for general applications. To overcome this issue, in this paper, a constitutive plastic-damage model with evolutive dilatancy is proposed for concrete. The evolution of dilatancy is made dependent on the plastic-damage and stress states. The proposed evolution law is validated by comparison of numerical simulations with available experimental results. The validation includes: concrete specimens under uniaxial compression measuring the free expansion, passively confined concrete specimens with different confining materials, and reinforced concrete panels under in-plane shear. It is concluded that the model accurately reproduces concrete lateral expansion through different nonlinear states. Proper modeling of concrete nonlinear expansion proves essential for capturing the response in a number of situations: softening under high shear stresses, confinement, and ductility assessment., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A variable order framework for 3D nonlinear analysis of reinforced concrete frames under general loading

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Moller, O.
A framework for the analysis of three-dimensional reinforced concrete frame structures, capable of reproducing general failure modes, is presented. A force-based model which guarantees the equilibrium between nodal and sectional forces is enhanced by means of a cross-sectional model. It is capable of capturing the complex coupling between all the internal forces. Consequently, different failure modes can be reproduced such as shear, torsional, flexural or axial failures. Material modeling of concrete is made using a plastic-damage model that incorporates a variable dilatancy parameter. The sectional and constitutive models are implemented in OpenSees. The sectional model can be used at each integration point of the force-based element. Alternatively, it can be used only where high coupling between the internal forces is expected, producing a variable order structural model. The validation shows that the frame element is capable of accurately reproduce beams and columns under monotonic and cyclic loads. The framework presented is a powerful numerical instrument for the analysis, design and assessment of reinforced concrete buildings and bridges., The first and second authors acknowledge the support provided by Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (ERDF), through the projects BIA2015-64672-C4-1R, BIA2012-36848 and RTI2018-097314-B-C21. The first author acknowledges the support of the Catalan Agency for University and Research through doctoral scholarship 2018FI-B1-00103. The third author acknowledges the support of the Research Council of Universidad Nacional de Rosario (CIUNR) and the Science and Technology Secretariat (SECyT), through the project 1ING601., Peer Reviewed, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.1 - Desenvolupar infraestructures fiables, sostenibles, resilients i de qualitat, incloent infraestructures regionals i transfrontereres, per tal de donar suport al desenvolupament econòmic i al benestar humà, amb especial atenció a l’accés assequible i equitatiu per a totes les persones, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.a - Facilitar el desenvolupament d’infraestructures sostenibles i resilients als països en desenvolupament per mitjà de més suport financer, tecnològic i tècnic als països africans, països menys avançats, països en desenvolu­pament sense litoral i petits estats insulars en desenvolupament, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima::13.1 - Enfortir la resiliència i la capacitat d’adaptació als riscos relacionats amb el clima i els desastres naturals a tots els països, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.b - Per a 2020, augmentar substancialment el nombre de ciutats i assentaments humans que adopten i posen en marxa polítiques i plans integrats per promoure la inclusió, l’ús eficient dels recursos, la mitigació del canvi climàtic i l’adaptació a aquest, així com la resiliència davant dels desastres, i desenvolupar i posar en pràctica una gestió integral dels riscos de desastre a tots els nivells, d’acord amb el Marc de Sendai per a la reducció del risc de desastres 2015.2030, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.5 - Per a 2030, reduir de forma significativa el nombre de morts causades per desastres, inclosos els relacio­nats amb l’aigua, i de persones afectades per aquests, i reduir substancialment les pèrdues econòmiques directes causades per desastres relacionades amb el producte interior brut mundial, fent un èmfasi especial en la protecció de les persones pobres i de les persones en situacions de vulnerabilitat
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Detección y medición semiautomática de fisuras en elementos de hormigón en fotos digitales usando procesamiento de imágenes

  • Sánchez Claderón, Luis
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
La fisuración es inevitable en las obras de hormigón armado, pero debe de ser controlada para asegurar un adecuado comportamiento en servicio y por durabilidad. El análisis de los patrones de fisuración es una parte esencial en el diagnóstico, monitorización y mantenimiento; para identificar deficiencias o situaciones comprometidas. Por otro lado, el patrón de fisuración también puede ser un indicador de la distribución tensional del hormigón y de los esfuerzos determinantes en una zona. En este artículo se presente un nuevo método para la búsqueda y medición de fisuras en imágenes en color de elementos de hormigón. El algoritmo usa diversas herramientas de procesamiento digital de imágenes para medir la orientación de las fisuras y entre estas herramientas destaca un tipo especial de filtros llamados “orientation kernels” desarrollados especialmente para detectar el ángulo y ancho de las fisuras., Esta investigación es parcialmente apoyada por los proyectos BIA2012-36848 “Performance-based design of partially prestressed concrete structures ”, y BIA2015-64672-C4-1-R “Contribution to the extension of service lifetime of existing concrete structures through an adequate structural evaluatio n and strengthening with advanced materials” , financiados a su vez por el Ministerio Economía, 14/14 Industria y Competitividad de España y por los Fond os Europos de Desarrollo Regional (FEDER). También se debe mencionar el financiamiento por par te de la Secretaria de Educación Superior, Ciencia, Tecnología y Educación (SENECYCT) (insituc ión del gobierno ecuatoriano) a través de una beca de “Convocatoria Abierta” para programas d e Masters y Phd., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Safety factor calibration for a new model of shear strength of reinforced concrete building beams and slabs

  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
When assessing existing structures, the availability of adequate safety factors, calibrated with the most accurate models, and for established target reliability indexes, is of critical importance in order to take the right decision regarding the maintenance/repair/strengthening interventions. In the case of shear resistance in reinforced concrete (RC) structures, when using the current design codes provisions for new constructions in assessment results that, in many cases, existing structures may be considered unsafe, implying large economic costs in strengthening or even dismantling. In this research, a proposal of safety factor relative to a recently developed model for shear strength, for elements with and without transversal reinforcement, based on a reliability-based calibration is presented. A formulation is proposed to determine the adequate strength factor for a selected target reliability index of the existing structure and desired remaining service life by means of a safety factor format, considering the load factors present in the Eurocodes. The calibration is carried out considering typical geometry and load ratios of building floors, as well as normal and high strength concrete. The derived safety factor is almost independent of the chosen remaining service life., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Resistencia a cortante de elementos de hormigón parcialmente pretensado

  • Celada Blesa, Ulric
  • Duarte Gómez, Noemí|||0000-0002-4542-8487
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
Se presenta una campaña experimental de elementos de hormigón parcialmente pretensado y una formulación a cortante basada en modelos mecánicos. Se compararán los resultados experimentales con diferentes normativas y se analizarán los parámetros más relevantes para la resistencia a cortante. Concluyendo que las normativas son muy conservadoras y que el nuevo modelo predice muy bien la resistencia a cortante
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Shear crack width assessment in concrete structures by 2D distributed optical fiber

  • Rodríguez, Gerardo
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
  • Villalba Herrero, Sergi|||0000-0001-6535-6372
This paper outlines the second part of an experimental study to show the capabilities of distributed optical fiber sensors (DOFS) in their application to the structural health monitoring (SHM) of the shear performance of concrete structures. SHM seeks to obtain the shear crack characteristics of concrete elements: detection, localization and quantification of shear damage. The two first were discussed in the first part of the experimental study. In the present paper, the quantification is dealt with by proposing a method to obtain the mean shear crack width in concrete beams. The method is based on the experimental data obtained by a DOFS bonded to the concrete surface. First, the basis of the methodology are presented and, later on, experimentally checked by testing of three partially pre-stressed concrete (PPC) beams subjected to a shear test with increasing level of load. The DOFS were deployed in the web of the beams to conform a 2D grid mesh to measure the strain profile along two orthogonal directions. The experimental data was obtained using an OBR (Optical Backscattered Reflectometer) system with high spatial resolution and sensitivity that allow a complete mapping of the cracking pattern and to obtain the required data for the calculation of the crack width. The results show the feasibility of the proposed method in calculating the shear crack width when compared to the results from traditional instrumentation, Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Shear crack pattern identification in concrete elements via distributed optical fibre grid

  • Rodríguez Gutiérrez, Gerardo
  • Casas Rius, Joan Ramon
  • Villalba Herrero, Sergi
This is an Accepted Manuscript of an article published by Taylor & Francis Group in "Structure and infrastructure engineering: maintenance, management, life-cycle design and performance" on 2019, available online at: http://www.tandfonline.com/10.1080/15732479.2019.1640256, An experimental methodology to obtain the shear cracking pattern in concrete elements is presented. The method is based on the use of Distributed Optical Fiber Sensors (DOFS) connected to an Optical Backscattered Reflectometer (OBR). Using this OBR system and a 2D grid conformed by one or two DOFS, the crack patterns of three partially pre-stressed concrete (PPC) beams subjected experimentally to shear failure, were obtained for increasing level of load. The 2D distributed fiber optic sensoring mesh was formed by attaching the fiber to the shear span of each beam using an epoxy adhesive. The importance of a correct DOFS attaching procedure to the concrete surface to obtain accurate results is described, and the principal advantages of DOFS to complement the use of discrete sensors in concrete experimental shear tests are shown. The proposed technique is a powerful tool to be implemented in the structural health monitoring in shear of concrete structures, where the variable inclined cracks are difficult to monitor by other experimental techniques using discrete sensors., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Crack detection in concrete elements from RGB pictures using modified line detection kernels

  • Sánchez Calderón, Luis
  • Bairán García, Jesús Miguel
Cracking is inevitable in ordinary reinforced concrete construction, yet it should be controlled to guarantee adequate serviceability and durability. Crack patterns analysis is essential for diagnosis, monitoring and maintenance, to identify malfunctioning or unsafe situations. An important part of this state is the cracking pattern of the elements as an indicator of the tensional distribution in the concrete. A method to search and measure fissures in RGB images of concrete elements has been developed and implemented as a MATLAB script. The algorithm uses several digital image processing tools to detect the measure, the cracks width and orientation; featuring these tools are the spatial filters called “orientation kernels” developed especially for detecting the angle and width of the cracks., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical simulation since early ages of the RG8 beam test from concrack benchmark by means of a 3D fibre frame model

  • Crespo Garibay, María Delia
  • Ferreira, Denise
  • Bairán García, Jesús Miguel
  • Marí Bernat, Antonio Ricardo
This work presents the numerical analysis of the RG8 test performed by the French research program Concrack2 in 2011. It consisted in a large RC beam specimen loaded in bending after restrained shrinkage. The specimen is composed of a central thinner part and two massive heads linked by two cylindrical struts that restrained strains due to thermal effects and autogenous shrinkage occurring in the concrete central part. After 8 weeks, the beam was loaded near to its ultimate capacity. The numerical model is based on the 3D fibre beam approach, capable of reproducing the response since early ages. The cross-section is discretized into fibres to take into account the different maturity levels within the crosssection. The analysis is divided into three phases: i) the thermal analysis determines the development of temperatures due to cement hydration and heat transfer, solar radiation and night cooling effects, ii) nonlinear mechanical analysis for early ages including creep, autogenous shrinkage and ageing and iii) nonlinear mechanical analysis for loading phase includes the interaction of normal and shear forces. Performance is compared against experimentation and the development of early age stresses discussed., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Resistencia a cortante de elementos de hormigón parcialmente pretensado

  • Celada Blesa, Ulric
  • Duarte Gómez, Noemí
  • Bairán García, Jesús Miguel
  • Oller Ibars, Eva
  • Marí Bernat, Antonio Ricardo
Se presenta una campaña experimental de elementos de hormigón parcialmente pretensado y una formulación a cortante basada en modelos mecánicos. Se compararán los resultados experimentales con diferentes normativas y se analizarán los parámetros más relevantes para la resistencia a cortante. Concluyendo que las normativas son muy conservadoras y que el nuevo modelo predice muy bien la resistencia a cortante, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A new concrete plastic-damage model with an evolutive dilatancy parameter

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel
Typical plastic-damage models for concrete use a constant dilatancy parameter. On problems sensitive to confinement and shear softening, this parameter needs ad hoc calibration to fit experimental observations. This makes the model not objective for general applications. To overcome this issue, in this paper, a constitutive plastic-damage model with evolutive dilatancy is proposed for concrete. The evolution of dilatancy is made dependent on the plastic-damage and stress states. The proposed evolution law is validated by comparison of numerical simulations with available experimental results. The validation includes: concrete specimens under uniaxial compression measuring the free expansion, passively confined concrete specimens with different confining materials, and reinforced concrete panels under in-plane shear. It is concluded that the model accurately reproduces concrete lateral expansion through different nonlinear states. Proper modeling of concrete nonlinear expansion proves essential for capturing the response in a number of situations: softening under high shear stresses, confinement, and ductility assessment., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Detección y medición semiautomática de fisuras en elementos de hormigón en fotos digitales usando procesamiento de imágenes

  • Sánchez Claderón, Luis
  • Bairán García, Jesús Miguel
La fisuración es inevitable en las obras de hormigón armado, pero debe de ser controlada para asegurar un adecuado comportamiento en servicio y por durabilidad. El análisis de los patrones de fisuración es una parte esencial en el diagnóstico, monitorización y mantenimiento; para identificar deficiencias o situaciones comprometidas. Por otro lado, el patrón de fisuración también puede ser un indicador de la distribución tensional del hormigón y de los esfuerzos determinantes en una zona. En este artículo se presente un nuevo método para la búsqueda y medición de fisuras en imágenes en color de elementos de hormigón. El algoritmo usa diversas herramientas de procesamiento digital de imágenes para medir la orientación de las fisuras y entre estas herramientas destaca un tipo especial de filtros llamados “orientation kernels” desarrollados especialmente para detectar el ángulo y ancho de las fisuras., Esta investigación es parcialmente apoyada por los proyectos BIA2012-36848 “Performance-based design of partially prestressed concrete structures ”, y BIA2015-64672-C4-1-R “Contribution to the extension of service lifetime of existing concrete structures through an adequate structural evaluatio n and strengthening with advanced materials” , financiados a su vez por el Ministerio Economía, 14/14 Industria y Competitividad de España y por los Fond os Europos de Desarrollo Regional (FEDER). También se debe mencionar el financiamiento por par te de la Secretaria de Educación Superior, Ciencia, Tecnología y Educación (SENECYCT) (insituc ión del gobierno ecuatoriano) a través de una beca de “Convocatoria Abierta” para programas d e Masters y Phd., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A variable order framework for 3D nonlinear analysis of reinforced concrete frames under general loading

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel
  • Moller, O.
A framework for the analysis of three-dimensional reinforced concrete frame structures, capable of reproducing general failure modes, is presented. A force-based model which guarantees the equilibrium between nodal and sectional forces is enhanced by means of a cross-sectional model. It is capable of capturing the complex coupling between all the internal forces. Consequently, different failure modes can be reproduced such as shear, torsional, flexural or axial failures. Material modeling of concrete is made using a plastic-damage model that incorporates a variable dilatancy parameter. The sectional and constitutive models are implemented in OpenSees. The sectional model can be used at each integration point of the force-based element. Alternatively, it can be used only where high coupling between the internal forces is expected, producing a variable order structural model. The validation shows that the frame element is capable of accurately reproduce beams and columns under monotonic and cyclic loads. The framework presented is a powerful numerical instrument for the analysis, design and assessment of reinforced concrete buildings and bridges., The first and second authors acknowledge the support provided by Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (ERDF), through the projects BIA2015-64672-C4-1R, BIA2012-36848 and RTI2018-097314-B-C21. The first author acknowledges the support of the Catalan Agency for University and Research through doctoral scholarship 2018FI-B1-00103. The third author acknowledges the support of the Research Council of Universidad Nacional de Rosario (CIUNR) and the Science and Technology Secretariat (SECyT), through the project 1ING601., Peer Reviewed, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.1 - Desenvolupar infraestructures fiables, sostenibles, resilients i de qualitat, incloent infraestructures regionals i transfrontereres, per tal de donar suport al desenvolupament econòmic i al benestar humà, amb especial atenció a l’accés assequible i equitatiu per a totes les persones, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.a - Facilitar el desenvolupament d’infraestructures sostenibles i resilients als països en desenvolupament per mitjà de més suport financer, tecnològic i tècnic als països africans, països menys avançats, països en desenvolu­pament sense litoral i petits estats insulars en desenvolupament, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima::13.1 - Enfortir la resiliència i la capacitat d’adaptació als riscos relacionats amb el clima i els desastres naturals a tots els països, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.b - Per a 2020, augmentar substancialment el nombre de ciutats i assentaments humans que adopten i posen en marxa polítiques i plans integrats per promoure la inclusió, l’ús eficient dels recursos, la mitigació del canvi climàtic i l’adaptació a aquest, així com la resiliència davant dels desastres, i desenvolupar i posar en pràctica una gestió integral dels riscos de desastre a tots els nivells, d’acord amb el Marc de Sendai per a la reducció del risc de desastres 2015.2030, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.5 - Per a 2030, reduir de forma significativa el nombre de morts causades per desastres, inclosos els relacio­nats amb l’aigua, i de persones afectades per aquests, i reduir substancialment les pèrdues econòmiques directes causades per desastres relacionades amb el producte interior brut mundial, fent un èmfasi especial en la protecció de les persones pobres i de les persones en situacions de vulnerabilitat, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Shear crack width assessment in concrete structures by 2D distributed optical fiber

  • Rodríguez, Gerardo
  • Casas Rius, Joan Ramon
  • Villalba Herrero, Sergi
This paper outlines the second part of an experimental study to show the capabilities of distributed optical fiber sensors (DOFS) in their application to the structural health monitoring (SHM) of the shear performance of concrete structures. SHM seeks to obtain the shear crack characteristics of concrete elements: detection, localization and quantification of shear damage. The two first were discussed in the first part of the experimental study. In the present paper, the quantification is dealt with by proposing a method to obtain the mean shear crack width in concrete beams. The method is based on the experimental data obtained by a DOFS bonded to the concrete surface. First, the basis of the methodology are presented and, later on, experimentally checked by testing of three partially pre-stressed concrete (PPC) beams subjected to a shear test with increasing level of load. The DOFS were deployed in the web of the beams to conform a 2D grid mesh to measure the strain profile along two orthogonal directions. The experimental data was obtained using an OBR (Optical Backscattered Reflectometer) system with high spatial resolution and sensitivity that allow a complete mapping of the cracking pattern and to obtain the required data for the calculation of the crack width. The results show the feasibility of the proposed method in calculating the shear crack width when compared to the results from traditional instrumentation, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Safety factor calibration for a new model of shear strength of reinforced concrete building beams and slabs

  • Bairán García, Jesús Miguel
  • Casas Rius, Joan Ramon
When assessing existing structures, the availability of adequate safety factors, calibrated with the most accurate models, and for established target reliability indexes, is of critical importance in order to take the right decision regarding the maintenance/repair/strengthening interventions. In the case of shear resistance in reinforced concrete (RC) structures, when using the current design codes provisions for new constructions in assessment results that, in many cases, existing structures may be considered unsafe, implying large economic costs in strengthening or even dismantling. In this research, a proposal of safety factor relative to a recently developed model for shear strength, for elements with and without transversal reinforcement, based on a reliability-based calibration is presented. A formulation is proposed to determine the adequate strength factor for a selected target reliability index of the existing structure and desired remaining service life by means of a safety factor format, considering the load factors present in the Eurocodes. The calibration is carried out considering typical geometry and load ratios of building floors, as well as normal and high strength concrete. The derived safety factor is almost independent of the chosen remaining service life., Peer Reviewed, Postprint (author's final draft)