Pasar al contenido principal

NUEVAS APLICACIONES DE ENSAYOS NO DESTRUCTIVOS BASADOS EN ONDAS MECANICAS PARA LA EVALUACION DE LA DEGRADACION EN MATERIALES CEMENTANTES.

BIA2014-55311-C2-1-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2014
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic signal modality: A novel approach for concrete damage evaluation

  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • Miralles Ricós, Ramón|||0000-0003-0039-2553
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Genovés, V.
[EN] In this paper, a new approach for characterizing material damage, using ultrasonic waves, is proposed. Two concrete series with two types of cement with different C3A content and similar mechanical properties were subjected to external sulphate attack (ESA) and evaluated using a novel Recurrence Plot Quantification Analysis (RQA) method. This brand new technique was compared with several methods, such as mechanical tests (compressive and flexural strength determination), dynamic test (dynamic modulus) measurements, and traditional ultrasonic measurements (propagation velocity and ultrasonic wave attenuation). In these experiments, RQA showed a high sensitivity to damage in spoiled series, improving the reliability of damage detection with ultrasonics in non-homogeneous materials compared to other non-destructive techniques. Interesting advantages of this new non-destructive technique are: a) the RQA parameter is normalized (range of 0 to 1); b) a calibration process is not required; c) the values of its standard deviation show the dispersion of the damage. It can contribute greatly to the diagnosis of the degree of damage to a material, when combined with other traditional measures such as the attenuation of the material., This work was supported by the Spanish Government under grants TEC2011-23403, BIA2014-55311-C2-1-P and BIA2014-55311-C2-2-P. This work is protected by the Spanish Patent and Trademark Office (SPTO) under reference P201630212.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic and impact spectroscopy monitoring on internal sulphate attack of cement-based materials

  • Genovés Gómez, Vicente
  • Vargas, F.
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] An exhaustive monitoring of an internal sulphate attack of Portland cement-based materials is addressed. Four series of Portland cement mortars with different amounts of gypsum (0%¿2% SO3 respect to the cement by mass) were monitored by means of physical, microstructural and non-destructive tests, studying specimens with a low expansion rate to examine the sensitivity of the applied techniques. The expansion analysis has shown the suitability of a fitting model, allowing the examination of two characteristic parameters: the characteristic time of the expansion reaction and the maximum amplitude of the expansion. In the mechanical analysis, higher values of Rc and Rf were attained as the gypsum content decreased. A microstructural analysis (thermogravimetry and FESEM) supported ettringite formation and expansion process. These results have been correlated with non-destructive tests: impact resonance acoustic spectroscopy and ultrasonic measures. The dynamic modulus and ultrasonic pulse velocity have closely predicted the stiffness of the specimens. The total material attenuation (absorbed energy of the chirp signal ultrasonic wave) presented different trends, showing clear differences for the most damaged series (2% SO3). Attenuation supplied interesting information about the hardening process and the microcracking effect due to a mortar expansion higher than 0.04%. The novelties of this study are the exhaustive monitoring of an internal sulphate attack, as well as the examination of the sensitivity of brand new NDT techniques when this damage process overlaps with the curing process., This work has been supported by the Spanish Administration under grants TEC2011-23403, BIA2014-55311-C2-1-P and BIA2014-55311-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Airborne non-contact and contact broadband ultrasounds for frequency attenuation profile estimation of cementitious materials

  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Bosch Roig, Ignacio|||0000-0003-3190-3635
  • Wright, W.M.D.
  • Jiang, W.
  • Genovés, V.
[EN] In this paper, the study of frequency-dependent ultrasonic attenuation in strongly heterogeneous cementitious materials is addressed. To accurately determine the attenuation over a wide frequency range, it is necessary to have suitable excitation techniques. We have analysed two kinds of ultrasound techniques: contact ultrasound and airborne non-contact ultrasound. The mathematical formulation for frequency-dependent attenuation has been established and it has been revealed that each technique may achieve similar results but requires specific different calibration processes. In particular, the airborne non-contact technique suffers high attenuation due to energy losses at the air-material interfaces. Thus, its bandwidth is limited to low frequencies but it does not require physical contact between transducer and specimen. In contrast, the classical contact technique can manage higher frequencies but the measurement depends on the pressure between the transducer and the specimen. Cement specimens have been tested with both techniques and frequency attenuation dependence has been estimated. Similar results were achieved at overlapping bandwidth and it has been demonstrated that the airborne non-contact ultrasound technique could be a viable alternative to the classical contact technique., The authors acknowledge the support from University College Cork (Ireland), Universidad Politecnica de Valencia and the Spanish Administration under grant BIA2014-55311-C2-2-P and Salvador Madariaga's Programme (PR2016-00344/PR2017-00658).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic broadband signal monitoring of Glass-fiber Reinforced Cement (GRC) bending tests

  • Genovés, V.
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Miralles Ricós, Ramón|||0000-0003-0039-2553
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] In this study, complete ultrasonic monitoring of Glass-fiber Reinforced Cement plates under bending tests was addressed. In this kind of experiment, the mechanical properties of the specimen continuously change during the test, thus, the acquisition time of the ultrasonic signals is a critical variable. In order to overcome this drawback, a new ultrasonic procedure based on broadband signals (chirp) has been applied. Following this line of thought, the analysed ultrasonic parameters have been split into the parameters that only depend on time, and those that depend on both time and frequency. In particular,the frequency dependent attenuation parameter allows characterizing the evolution of the plate being damaged over a wide frequency range and significantly detecting the main two events happening during the experiment: the first crack and the maximum stress point. In short, this paper demonstrates the suitability of ultrasonic broadband signals for characterizing fiber-reinforced cementitious composites under bending stress., This work has been supported by the Spanish Administration under grants, BES-2015-071469, TEC2011-23403, BIA2014-55311-C2-1-P and BIA2014-55311-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Flipped Accumulative Non-Linear Single Impact Resonance Acoustic Spectroscopy (FANSIRAS): A novel feature extraction algorithm for global damage assessment

  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • Genovés, V.
  • Pérez, G.
[EN] High amplitude non-linear acoustic methods have shown great potential for the identification of micro-damage in inhomogeneous materials such as concrete. Usually, these methods evaluate non-linearity parameters related to the hysteretic behaviour from the dependence of the shifts in both frequency and damping on the amplitude of the strain. A deep understanding of the reverberation phenomena has been obtained in order to introduce a novel signal processing approach called FANSIRAS (Flipped Accumulative Nonlinear Single Impact Resonance Acoustic Spectroscopy). Traditional acoustic spectroscopy techniques, NIRAS (Non-linear Impact Resonance Acoustic Spectroscopy) and NSIRAS (Non-linear Single Impact Acoustic Spectroscopy), have been analyzed and compared with the brand new approach when providing quantitative information related to the degree of micro-cracking in thermal damaged concrete based materials. The new resonance-based algorithm demonstrates that the non-linear non-classical parameters can be determined through a single resonance frequency measurement, obtaining the expected sensitivity to internal damage. Its simplicity and robustness may be important in industrial applications. (C) 2018 Elsevier Ltd. All rights reserved., This work has been supported by the Spanish Administration under grants TEC2011-23403, BES2015-071469, BIA2014-55311-C2-1-P and BIA2014-55311-C2-2-P. The authors are also grateful for FEDER funds.