Pasar al contenido principal

TECNICAS MULTIESCALA PARA EL ANALISIS EXPERIMENTAL Y NUMERICO DE LA FIABILIDAD DE LAS ESTRUCTURAS DE OBRA DE FABRICA

BIA2015-63882-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 40
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Experimental analysis of the size effect on the compressive behaviour of cylindrical samples core-drilled from existing brick masonry

  • Segura Domingo, Jorge|||0000-0002-6763-1064
  • Pelà, Luca|||0000-0001-7760-8290
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
  • Cabané Cañas, Albert|||0000-0002-5858-2563
This paper presents the results of an experimental programme about the evaluation of the size effect on the compressive behaviour of cylindrical samples of existing masonry. The study focuses on the in-situ coring and experimental testing of core specimens with 150 mm and 90 mm diameter. The 150 mm cylinder, recurrent in minor destructive evaluation of the compressive strength of existing masonry, includes four brick pieces, two mortar beds and one head joint. The 90 mm specimen includes one mortar bed and two segments of brick, and inflicts less damage on the inspected structural member due to its lower invasivity. The experimental research investigates the size effect on four different types of clay brick masonry. The first type was built in the laboratory using historical-like materials. The other three types of masonry belong to structural walls of existing historical buildings. The combination of experimental results from laboratory controlled materials and existing historical members shows that the size of the cylindrical specimen has regular effect on the compressive strength and the Young’s modulus. The consistent relationship found between the compressive strengths of the 150 mm and 90 mm core samples allows the use of the latter specimen for a more respectful inspection of existing structural masonry., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

In-plane shear behaviour by diagonal compression testing of brick masonry walls strengthened with basalt and steel textile reinforced mortars

  • Garcia Ramonda, Larisa|||0000-0001-5438-6314
  • Pelà, Luca|||0000-0001-7760-8290
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
  • Camata, Guido
This paper presents an experimental study of the structural behaviour of masonry walls retrofitted with Textile Reinforced Mortar (TRM) to improve their in-plane shear strength and deformation capacity. The experimental programme consists in diagonal compression testing of ten specimens of clay brick and lime mortar masonry retrofitted with three different TRM systems: i) continuous bidirectional grids of basalt TRM, ii) discrete bands of unidirectional steel TRM and iii) continuous basalt TRM on the wall’s inner face and bed joints structural repointing with near surface mounted helical stainless steel bars on the wall’s outer face. Two of the specimens were tested two times, i.e. in the unreinforced condition and subsequently in the repaired configuration including basalt TRM retrofitting. The experimental results show that the adopted TRM solutions produce a beneficial increase of shear resistance and ductility, making them suitable for seismic retrofitting and post-earthquake repair., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Building survey forms for heterogeneous urban areas in seismically hazardous zones: application to the historical center of Valparaíso, Chile

  • Jiménez, Belén
  • Pelà, Luca|||0000-0001-7760-8290
  • Hurtado, Marcela
Building survey is an essential data-collection procedure to feed large-scale seismic vulnerability assessment. The available strategies usually consider survey forms to gather information about the urban buildings. The application of the available survey forms poses important challenges for the case of the heterogeneous urban centers including different structural typologies. This work proposes four specific survey forms for traditional structural typologies constructed with masonry, reinforced concrete, mixed steel-reinforced concrete, and timber. The proposed forms request essential information on the parameters necessary for seismic vulnerability assessment, by evaluating the lateral-load resistant system, regularity, condition of conservation, and existing damages. The survey forms were applied to the study of 111 buildings of the historical center of Valparaíso, Chile. The proposed methodology was complemented with the use of Geographic Information Systems to obtain a complete database with the structural characterization of the most representative typologies for future works of large-scale seismic vulnerability assessment., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Dynamic identification and static loading tests of timbrel vaults: application to a Modernist 20th century heritage structure

  • Endo, Yohei
  • Llorens Sulivera, Miquel
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
  • Pelà, Luca|||0000-0001-7760-8290
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2017, available online at: http://www.tandfonline.com/10.1080/15583058.2016.1277566, This paper presents the study of the structural performance of a set of timbrel vaults belonging to the so-called Administration Pavilion of the Hospital de Sant Pau, a large-scale hospital complex located in Barcelona. The paper includes three parts. First, the Administration pavilion of Hospital de Sant Pau is described by putting the emphasis on the geometry of the masonry vaults and the combined utilisation of steel and masonry structural members. Second, laboratory and in-situ experiments are discussed. Finally, the behaviour observed during the dynamic-identification and the static-loading tests is simulated by means of FEM analysis. The FEM models prepared to analyse the vaults take explicitly into account the direct effect of secondary masonry structural elements, such as the upper slab and the extrados stiffening diaphragms. The comparison indicates that the consideration of these structural elements is essential for an adequate FEM simulation of both the dynamic and the static behaviour of the timbrel vaults., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Influence of recycled limestone filler additions on the mechanical behaviour of commercial premixed hydraulic lime based mortars

  • Segura Domingo, Jorge|||0000-0002-6763-1064
  • Aponte Hernández, Diego Fernando|||0000-0001-5737-7819
  • Pelà, Luca|||0000-0001-7760-8290
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
This paper presents an experimental programme aimed at investigating the use of limestone filler additions to modify the mechanical properties of commercial premixed hydraulic lime based mortars. The influence of adding recycled limestone filler was evaluated from the mechanical point of view, i.e. by comparing the experimental compressive and flexural strengths of five different mortar mixes with variable filler contents. The comparison of results shows that, up to a certain amount, the addition of filler provides an improvement of the mortar’s mechanical properties. Beyond this optimum limit, strengths tend to decrease and eventually stabilize. Hence, mortars tested as part of this experimental campaign covered a range of strengths. Consequently, adding limestone filler can serve to adapt the applicability of hydraulic lime mortars to different practical applications, from the conservation of historical buildings to laboratory research on masonry., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Review of different pushover analysis methods applied to masonry buildings and comparison with nonlinear dynamic analysis

  • Endo, Yohei
  • Pelà, Luca|||0000-0001-7760-8290
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
This is an Accepted Manuscript of an article published by Taylor & Francis Group in Journal of Earthquake Engineering on 2016, available online at: http://www.tandfonline.com/doi/full/10.1080/13632469.2016.1210055., This article presents the comparison among different nonlinear seismic analysis methods applied to masonry buildings, i.e., pushover analyses with invariant lateral force distributions, adaptive pushover analysis and nonlinear dynamic analysis. The study focuses on the influence of lateral force distribution on the results of the pushover analysis. Two simple benchmark case studies are considered for the purpose of the research, i.e., a four-wall masonry building prototype without floor rigid diaphragms and a two-wall system with a cross-vault. The comparative study offers a useful review of pushover analysis methods for masonry structures and shows advantages and possible limitations of each approach., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Influence of geometry of cylindrical samples in the mechanical characterization of existing brickwork

  • Segura, Jorge
  • Pelà, Luca|||0000-0001-7760-8290
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
The mechanical characterization of masonry is of paramount importance for the structural assess-ment of historical constructions against both vertical and horizontal actions. In particular, the compressive strength of masonry is normally regarded as a critical parameter for structural analysis. However, an accurate determination of the mechanical properties of masonry is a difficult task due to the complex and heterogene-ous behavior of the material. The mechanical characterization of historical masonry is also hindered by the need to limit damage caused by inspection in culturally valuable buildings. Recent researches and standards point to the possibility of estimating the compressive strength of existing brickwork by testing cylindrical samples of at least 150 mm diameter extracted from the brickwork walls. This work investigates the possibility of carrying out similar tests on smaller diameter cylinders. Using smaller cyl-inders may allow the extraction of a larger amount of samples and also permit the reduction of the extent of damage caused to the building. This study presents a comparison between compression tests performed on 150 mm and 90 mm diameter cy-lindrical samples to evaluate the strength and stiffness of masonry consisting of lime mortar and clay bricks. The tests were carried out in the laboratory on samples extracted from masonry walls by using a dry core-drilling procedure and then regularized with high strength mortar caps. The experimental results show the re-lationship between the different geometries of core samples regarding strength values, failure modes and crack patterns. The study contributes to the application of experimental tests on cylindrical samples as a minor de-structive technique to estimate the mechanical parameters of historical brickwork under compression.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Challenges, tools and applications of tracking algorithms in the numerical modelling of cracks in concrete and masonry structures

  • Saloustros, Savvas|||0000-0002-9513-8373
  • Cervera Ruiz, Miguel|||0000-0003-3437-6703
  • Pelà, Luca|||0000-0001-7760-8290
The final publication is available at Springer via http://dx.doi.org/10.1007/s11831-018-9274-3, The importance of crack propagation in the structural behaviour of concrete and masonry structures has led to the development of a wide range of finite element methods for crack simulation. A common standpoint in many of them is the use of tracking algorithms, which identify and designate the location of cracks within the analysed structure. In this way, the crack modelling techniques, smeared or discrete, are applied only to a restricted part of the discretized domain. This paper presents a review of finite element approaches to cracking focusing on the development and use of tracking algorithms. These are presented in four categories according to the information necessary for the definition and storage of the crack-path. In addition to that, the most utilised criteria for the selection of the crack propagation direction are summarized. The various algorithmic issues involved in the development of a tracking algorithm are discussed through the presentation of a local tracking algorithm based on the smeared crack approach. Challenges such as the modelling of arbitrary and multiple cracks propagating towards more than one direction, as well as multi-directional and intersecting cracking, are detailed. The presented numerical model is applied to the analysis of small- and large-scale masonry and concrete structures under monotonic and cyclic loading., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Out-of-plane seismic response and failure mechanism of masonry structures using finite elements with enhanced strain accuracy

  • Vlachakis, Georgios
  • Cervera Ruiz, Miguel|||0000-0003-3437-6703
  • Barbat Vlad, Gabriel|||0000-0002-3675-5558
  • Saloustros, Savvas|||0000-0002-9513-8373
The out-of-plane response is a complex and at the same time key aspect of the seismic vulnerability of masonry structures. It depends on several factors, some of which are the material properties, the quality of the walls, the geometry of the structure, the connections between structural elements and the stiffness of the diaphragms. During the last years, a wide variety of numerical methods has been employed to assess the out-of-plane behaviour of unreinforced masonry structures. Finite element macro-modelling approaches are among the most famous as they allow modelling large structures at a reasonable computational cost. However, macro-modelling approaches may result in a non-realistic representation of localized cracks and a dependency of the numerical solution on the finite element mesh. Mixed strain/displacement finite elements have been recently proposed as a remedy to the above nu-merical pathologies. Due to the independent interpolation of strains and displacements these finite element formulations are characterized by an enhanced accuracy in strain localization and crack propagation problems, being at the same time practically mesh independent. For these reasons, mixed finite elements are employed in this work for the out-of-plane assessment of unreinforced masonry struc-tures, being at the same time their first real-scale application. A full-scale experimental campaign of two masonry structures, a stone and a brick one, subjected to shaking-table tests is chosen as reference benchmark. Their structural response under seismic actions is numerically assessed through nonlinear static analysis. The proposed approach is validated through the comparison of the numerical results with the experimental ones, as well as with the results obtained using standard irreducible finite ele-ments., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Torque Penetrometric Test for the in-situ characterisation of historical mortars: fracture mechanics interpretation and experimental validation

  • Marastoni, Diego
  • Benedetti, Andrea
  • Pelà, Luca|||0000-0001-7760-8290
  • Pignagnoli, Giacomo
The assessment of historical structures requires appropriate knowledge of the behaviour of the investigated materials. Concerning masonry, its mechanical characterisation is a challenging task, since its composite nature requires the careful evaluation of the behaviour of its material components. In particular, the experimental assessment of the strength of existing mortar in historical structures still encounters several difficulties. This study investigates a novel Minor Destructive Testing (MDT) technique virtually equivalent to the vane test used for soils. The instrumentation, called herein Torque Penetrometric Test (TPT), is composed of a steel nail with four protruding teeth and a torque wrench. The test consists in inserting the toothed nail into a mortar joint and then applying a torque by means of a dynamometric key, until reaching the failure of the material. This work presents a novel interpretation theory based on basic concepts of fracture mechanics and applied to the micro-mechanical analysis of the stress state induced by the instrument on the investigated mortar. The proposed interpretative theory is validated through the execution of experimental tests in the laboratory and in a historical masonry building. The test proves to be effective for a quick in-situ MDT evaluation of the strength of existing mortars., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Analytical derivation of seismic fragility curves for historical masonry structures based on stochastic analysis of uncertain material parameters

  • Saloustros, Savvas|||0000-0002-9513-8373
  • Pelà, Luca|||0000-0001-7760-8290
  • Contrafatto, Francesca Romana
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
  • Petromichelakis, Yiannis
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2019, available online at: http://www.tandfonline.com/10.1080/15583058.2019.1638992, This work presents a probabilistic method to assess the seismic vulnerability of historical masonry structures, such as churches or cathedrals, including uncertainty analysis of the material parameters. The proposed approach considers the pushover analysis using the finite element method for the structural evaluation of the seismic behaviour of masonry structures. A stochastic analysis based on Monte Carlo simulation investigates the effect of the uncertainty of the structural members’ mechanical parameters on the evaluation of the seismic fragility. The method is applied to the seismic assessment of the bay structure of Santa Maria del Mar church in Barcelona, Spain. This case study is characterised by complex geometry and material heterogeneity, and shows to be sensitive enough to the uncertainty of the material properties to experience two possible collapse mechanisms in case of an earthquake. The study presents how to derive analytical seismic fragility curves by considering the uncertainties regarding the material properties and the different types of collapse mechanism., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Investigation on experimental techniques for the mechanical characterization of brick masonry

  • Roca Fabregat, Pedro|||0000-0001-5400-5817
  • Pelà, Luca|||0000-0001-7760-8290
One of the main difficulties found in the assessment and verification of masonry historical structures lays in the characterization of the main mechanical properties of the material components (units and mortar) and masonry as composite material. In an attempt to provide possible approaches for mechanical characterization, the paper presents and discusses different Minor Destructive Tests (MDTs) oriented to the measurement of the compressive strength of mortar bed joints and masonry composite samples extracted from existing brick masonries. The MDTs discussed for mortar characterization are the Double Punch Test (DPT), the Windsor Pin Penetration Test (PPT) and the Helix Screw Pull-Out Test (HPT). The method presented for the characterization of masonry as composite encompasses laboratory tests on cylindrical core samples. Different types of cylindrical samples, corresponding to alternative sizes and geometrical joint configurations, are investigated based on-purpose built laboratory walls and from a set of real case studies. The proposed MDTs are appraised with regard to their reliability and real applicability., The authors gratefully acknowledge the financial support provided by the Ministry of Economy and Competitiveness and from the Ministry of Science, Innovation and Universities (MCIU) of the Spanish Government and the State Agency of Research (AEI), as well as that of the European Regional Development Fund (FEDER) through projects MULTIMAS (BIA2015-63882-P) and SEVERUS (RTI2018-099589-B-I00)., Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.4 - Redoblar els esforços per a protegir i salvaguardar el patrimoni cultural i natural del món
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Tracking multi-directional intersecting cracks in numerical modelling of masonry shear walls under cyclic loading

  • Saloustros, Savvas|||0000-0002-9513-8373
  • Cervera Ruiz, Miguel|||0000-0003-3437-6703
  • Pelà, Luca|||0000-0001-7760-8290
The final publication is available at Springer via http://dx.doi.org/10.1007/s11012-017-0712-3, In-plane cyclic loading of masonry walls induces a complex failure pattern composed of multiple diagonal shear cracks, as well as flexural cracks. The realistic modelling of such induced localized cracking necessitates the use of costly direct numerical simulations with detailed information on both the properties and geometry of masonry components. On the contrary, computationally efficient macro-models using standard smeared-crack approaches often result in a poor representation of fracture in the simulated material, not properly localized and biased by the finite element mesh orientation. This work proposes a possible remedy to these drawbacks of macro-models through the use of a crack-tracking algorithm. The macro-modelling approach results in an affordable computational cost, while the tracking algorithm aids the mesh-bias independent and localized representation of cracking. A novel methodology is presented that allows the simulation of intersecting and multi-directional cracks using tracking algorithms. This development extends the use of localized crack approaches using tracking algorithms to a wider field of applications exhibiting multiple, arbitrary and interacting cracking. The paper presents also a novel formulation including into an orthotropic damage model the description of irreversible deformations under shear loading. The proposed approach is calibrated through the comparison with an experimental test on a masonry shear wall against in-plane cyclic loading., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Dynamic elastic properties of brick masonry constituents

  • Makoond, Nirvan Chandra|||0000-0002-5203-6318
  • Pelà, Luca|||0000-0001-7760-8290
  • Molins i Borrell, Climent|||0000-0001-8292-0473
When subjected to dynamic loading, materials can exhibit a mechanical behaviour quite different from its static counterpart. The evaluation of dynamic properties is thus very useful in the assessment of existing masonry structures. This paper presents results of an experimental campaign to determine both the dynamic Young’s modulus and the shear modulus of brick masonry constituents through two non-destructive testing methods. Following a discussion on the reliability of the methods, a robust procedure is described and tested on a variety of samples. The results show that the techniques can be successfully applied to provide reliable estimates of the dynamic elastic properties of brick masonry constituents., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

In-plane cyclic loading of masonry walls strengthened by vegetal-fabric-reinforced cementitious matrix (FRCM) composites

  • Mercedes Cedeño, Luis Enrique|||0000-0003-2520-8599
  • Bernat Masó, Ernest|||0000-0002-7080-0957
  • Gil Espert, Lluís|||0000-0002-2007-4846
Fabric-reinforced cementitious matrix (FCRMs) are promising composite materials for the retrofitting and reinforcement of existing structures. In this study, vegetal meshes consisting of hemp and cotton coated with epoxy were manufactured and combined with a cementitious matrix to strengthen masonry walls. A synthetic glass fibre mesh was also tested. Several walls were manufactured, strengthened, and tested under cyclic loading. The results allow us to compare the performances of different mesh configurations in terms of size and materials. All strengthening solutions significantly increased shear strength capacity and the ability to dissipate energy compared to unreinforced walls. Further, all strengthened walls exhibited multi-track pattern distributions and achieved distortion capacity improvements of up to 300%. Indicators of stiffness, energy dissipation, damping, residual deformation, and damage allow us to compare the strengthening performances of different solutions. The vegetal solutions provided superior efficiency compared to the glass-FRCM strengthened walls. Additionally, the use of a larger volume of vegetal fibres reduces the consumption of cement and can provide a sustainable solution. The main failure mechanism of the vegetal-FCRMs was debonding, which can be remedied by improvements to material interfaces., The authors gratefully acknowledge financial support from the Ministerio de Economía y Competitividad of the Spanish Government and the European Regional Development Fund through the MULTIMAS project (ref. num. BIA2015-63882-P). The first author also acknowledges the Ministry of Education Science and Technology of the Dominican Republic for financial support through its international scholarship program., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Combined in-situ and laboratory minor destructive testing of historical mortars

  • Pelà, Luca|||0000-0001-7760-8290
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
  • Aprile, Alessandra
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2018, available online at: http://www.tandfonline.com/10.1080/15583058.2017.1323247., Mortar is of all masonry components the most difficult to be experimentally characterised in heritage buildings. This paper investigates the possibility of combining different in-situ and laboratory minor destructive testing (MDT) techniques to assess the strength of mortar in historical brickwork. Lime mortar and clay brick walls were built in the laboratory and then tested in order to derive empirical correlation rules among three different MDT techniques: double punch test (DPT), helix pull-out test (HPT) and pin penetration test (PPT). The outcomes of this activity were used eventually to assess the mortar properties of an important historical heritage structure, Casa Puig i Cadafalch, located near Barcelona. The research is intended to promote the use of MDT in studies and conservation works on built cultural heritage by providing criteria for the evaluation of the strength of existing mortar with respectful sampling and testing techniques., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Masonry walls strengthened with vegetal fabric reinforced cementitious matrix (FRCM) composites

  • Mercedes Cedeño, Luis Enrique|||0000-0003-2520-8599
  • Bernat Masó, Ernest|||0000-0002-7080-0957
  • Gil Espert, Lluís|||0000-0002-2007-4846
Fabric-reinforced cementitious matrices (FCRMs) are promising composite materials for the retrofitting and reinforcement of existing structures. In this study, vegetal meshes consisting of hemp and cotton coated with epoxy were manufactured and combined with a cementitious matrix to strengthen masonry walls. A synthetic glass fibre mesh was also tested. Several walls were manufactured, strengthened, and tested under cyclic loading. The results allow us to compare the performances of different mesh configurations in terms of size and materials. All strengthening solutions significantly increased shear strength capacity and the ability to dissipate energy compared to unreinforced walls. Further, all strengthened walls exhibited multi-track pattern distributions and achieved distortion capacity improvements of up to 300%. Indicators of stiffness, energy dissipation, damping, residual deformation, and damage allow us to compare the strengthening performances of different solutions. The vegetal solutions provided superior efficiency compared to the glass-FRCM strengthened walls. Additionally, the use of a larger volume of vegetal fibres reduces the consumption of cement and can provide a sustainable solution. The main failure mechanism of the vegetal-FCRMs was debonding, which can be remedied by improvements to material interfaces., The authors gratefully acknowledge financial support from the Ministerio de Economía y Competitividad of the Spanish Government and the European Regional Development Fund through the MULTIMAS project (ref. num. BIA2015-63882-P)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Propiedades mecánicas de compuestos de matriz cementicia reforzados con tejidos pretensados (PFRCM)

  • Bernat Masó, Ernest|||0000-0002-7080-0957
  • Mercedes Cedeño, Luis Enrique|||0000-0003-2520-8599
  • Gil Espert, Lluís|||0000-0002-2007-4846
La matriz cementicia reforzada con tejidos (FRCM) es un material de refuerzo compuesto que se usa para reforzar estructuras de mampostería y de hormigón de forma pasiva, debido al requisito de activación de fisuras. Se propone pretensar el tejido para superar esta limitación, aumentar la resistencia a la fisuración y obtener una respuesta más rígida. Con este objetivo, se realizaron más de 200 ensayos de tracción en especímenes FRCM para analizar la influencia de los tejidos pretensados. También se analizaron otras variables, como el sistema de fijación, la velocidad de ensayo, el tipo de matriz y el tipo de tejidos. Las evidencias llevan a la conclusión de que pretensar el tejido del FRCM es una forma eficaz de aumentar su resistencia a la fisuración (más del 30%) y la rigidez a tracción.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

An enhanced finite element macro-model for the realistic simulation of localized cracks in masonry structures: a large-scale application

  • Saloustros, Savvas|||0000-0002-9513-8373
  • Pelà, Luca|||0000-0001-7760-8290
  • Cervera Ruiz, Miguel|||0000-0003-3437-6703
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2018, available online at: http://www.tandfonline.com/10.1080/15583058.2017.1323245., Finite element macro-modelling approaches are widely used for the analysis of large-scale masonry structures. Despite their efficiency, they still face two important challenges: the realistic representation of damage and a reasonable independency of the numerical results to the used discretization. In this work, the classical smeared crack approach is enhanced with a crack-tracking algorithm, originating from the analysis of localized cracking in quasi-brittle materials. The proposed algorithm is for the first time applied to a large-scale wall exhibiting multiple shear and flexural cracking. Discussion covers structural aspects, as the response of the structure under different assumptions regarding the floor rigidity, but also numerical issues, commonly overlooked in the simulation of large structures, such the mesh-dependency of the numerical results., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Monotonic and cyclic testing of clay brick and lime mortar masonry in compression

  • Segura Domingo, Jorge|||0000-0002-6763-1064
  • Pelà, Luca|||0000-0001-7760-8290
  • Roca Fabregat, Pedro|||0000-0001-5400-5817
This research presents an experimental programme on the mechanical characterization of masonry under monotonic and cyclic uniaxial compression. Two different types of standard specimens, running bond walls and stack bond prisms, were built using handmade clay bricks and hydraulic lime mortar. The experimental results are compared and discussed in terms of strength, stiffness and deformability. It was observed that the two specimen types provided very similar results on both strength and stiffness. Cyclic loading tests carried out on a set of samples provided new experimental evidence on the stiffness degradation, loss of load carrying capacity for increasing irreversible compressive strains and energy dissipation. The paper presents eventually a thorough discussion about the comparison between the obtained experimental results with available predictive models for strength, stiffness and fracture energy of masonry under monotonic and cyclic compression loading., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Influence of recycled limestone filler additions on the mechanical behaviour of commercial premixed hydraulic lime based mortars

  • Segura Domingo, Jorge
  • Aponte Hernández, Diego Fernando
  • Pelà, Luca
  • Roca Fabregat, Pedro
This paper presents an experimental programme aimed at investigating the use of limestone filler additions to modify the mechanical properties of commercial premixed hydraulic lime based mortars. The influence of adding recycled limestone filler was evaluated from the mechanical point of view, i.e. by comparing the experimental compressive and flexural strengths of five different mortar mixes with variable filler contents. The comparison of results shows that, up to a certain amount, the addition of filler provides an improvement of the mortar’s mechanical properties. Beyond this optimum limit, strengths tend to decrease and eventually stabilize. Hence, mortars tested as part of this experimental campaign covered a range of strengths. Consequently, adding limestone filler can serve to adapt the applicability of hydraulic lime mortars to different practical applications, from the conservation of historical buildings to laboratory research on masonry., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Masonry walls strengthened with vegetal fabric reinforced cementitious matrix (FRCM) composites

  • Mercedes Cedeño, Luis Enrique
  • Bernat Masó, Ernest
  • Gil Espert, Lluís
Fabric-reinforced cementitious matrices (FCRMs) are promising composite materials for the retrofitting and reinforcement of existing structures. In this study, vegetal meshes consisting of hemp and cotton coated with epoxy were manufactured and combined with a cementitious matrix to strengthen masonry walls. A synthetic glass fibre mesh was also tested. Several walls were manufactured, strengthened, and tested under cyclic loading. The results allow us to compare the performances of different mesh configurations in terms of size and materials. All strengthening solutions significantly increased shear strength capacity and the ability to dissipate energy compared to unreinforced walls. Further, all strengthened walls exhibited multi-track pattern distributions and achieved distortion capacity improvements of up to 300%. Indicators of stiffness, energy dissipation, damping, residual deformation, and damage allow us to compare the strengthening performances of different solutions. The vegetal solutions provided superior efficiency compared to the glass-FRCM strengthened walls. Additionally, the use of a larger volume of vegetal fibres reduces the consumption of cement and can provide a sustainable solution. The main failure mechanism of the vegetal-FCRMs was debonding, which can be remedied by improvements to material interfaces., The authors gratefully acknowledge financial support from the Ministerio de Economía y Competitividad of the Spanish Government and the European Regional Development Fund through the MULTIMAS project (ref. num. BIA2015-63882-P)., Peer Reviewed, Preprint
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Challenges, tools and applications of tracking algorithms in the numerical modelling of cracks in concrete and masonry structures

  • Saloustros, Savvas
  • Cervera Ruiz, Miguel
  • Pelà, Luca
The final publication is available at Springer via http://dx.doi.org/10.1007/s11831-018-9274-3, The importance of crack propagation in the structural behaviour of concrete and masonry structures has led to the development of a wide range of finite element methods for crack simulation. A common standpoint in many of them is the use of tracking algorithms, which identify and designate the location of cracks within the analysed structure. In this way, the crack modelling techniques, smeared or discrete, are applied only to a restricted part of the discretized domain. This paper presents a review of finite element approaches to cracking focusing on the development and use of tracking algorithms. These are presented in four categories according to the information necessary for the definition and storage of the crack-path. In addition to that, the most utilised criteria for the selection of the crack propagation direction are summarized. The various algorithmic issues involved in the development of a tracking algorithm are discussed through the presentation of a local tracking algorithm based on the smeared crack approach. Challenges such as the modelling of arbitrary and multiple cracks propagating towards more than one direction, as well as multi-directional and intersecting cracking, are detailed. The presented numerical model is applied to the analysis of small- and large-scale masonry and concrete structures under monotonic and cyclic loading., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

In-plane shear behaviour by diagonal compression testing of brick masonry walls strengthened with basalt and steel textile reinforced mortars

  • Garcia Ramonda, Larisa
  • Pelà, Luca
  • Roca Fabregat, Pedro
  • Camata, Guido
This paper presents an experimental study of the structural behaviour of masonry walls retrofitted with Textile Reinforced Mortar (TRM) to improve their in-plane shear strength and deformation capacity. The experimental programme consists in diagonal compression testing of ten specimens of clay brick and lime mortar masonry retrofitted with three different TRM systems: i) continuous bidirectional grids of basalt TRM, ii) discrete bands of unidirectional steel TRM and iii) continuous basalt TRM on the wall’s inner face and bed joints structural repointing with near surface mounted helical stainless steel bars on the wall’s outer face. Two of the specimens were tested two times, i.e. in the unreinforced condition and subsequently in the repaired configuration including basalt TRM retrofitting. The experimental results show that the adopted TRM solutions produce a beneficial increase of shear resistance and ductility, making them suitable for seismic retrofitting and post-earthquake repair., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

An enhanced finite element macro-model for the realistic simulation of localized cracks in masonry structures: a large-scale application

  • Saloustros, Savvas
  • Pelà, Luca
  • Cervera Ruiz, Miguel
  • Roca Fabregat, Pedro
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2018, available online at: http://www.tandfonline.com/10.1080/15583058.2017.1323245., Finite element macro-modelling approaches are widely used for the analysis of large-scale masonry structures. Despite their efficiency, they still face two important challenges: the realistic representation of damage and a reasonable independency of the numerical results to the used discretization. In this work, the classical smeared crack approach is enhanced with a crack-tracking algorithm, originating from the analysis of localized cracking in quasi-brittle materials. The proposed algorithm is for the first time applied to a large-scale wall exhibiting multiple shear and flexural cracking. Discussion covers structural aspects, as the response of the structure under different assumptions regarding the floor rigidity, but also numerical issues, commonly overlooked in the simulation of large structures, such the mesh-dependency of the numerical results., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Combined in-situ and laboratory minor destructive testing of historical mortars

  • Pelà, Luca
  • Roca Fabregat, Pedro
  • Aprile, Alessandra
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2018, available online at: http://www.tandfonline.com/10.1080/15583058.2017.1323247., Mortar is of all masonry components the most difficult to be experimentally characterised in heritage buildings. This paper investigates the possibility of combining different in-situ and laboratory minor destructive testing (MDT) techniques to assess the strength of mortar in historical brickwork. Lime mortar and clay brick walls were built in the laboratory and then tested in order to derive empirical correlation rules among three different MDT techniques: double punch test (DPT), helix pull-out test (HPT) and pin penetration test (PPT). The outcomes of this activity were used eventually to assess the mortar properties of an important historical heritage structure, Casa Puig i Cadafalch, located near Barcelona. The research is intended to promote the use of MDT in studies and conservation works on built cultural heritage by providing criteria for the evaluation of the strength of existing mortar with respectful sampling and testing techniques., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Review of different pushover analysis methods applied to masonry buildings and comparison with nonlinear dynamic analysis

  • Endo, Yohei
  • Pelà, Luca
  • Roca Fabregat, Pedro
This is an Accepted Manuscript of an article published by Taylor & Francis Group in Journal of Earthquake Engineering on 2016, available online at: http://www.tandfonline.com/doi/full/10.1080/13632469.2016.1210055., This article presents the comparison among different nonlinear seismic analysis methods applied to masonry buildings, i.e., pushover analyses with invariant lateral force distributions, adaptive pushover analysis and nonlinear dynamic analysis. The study focuses on the influence of lateral force distribution on the results of the pushover analysis. Two simple benchmark case studies are considered for the purpose of the research, i.e., a four-wall masonry building prototype without floor rigid diaphragms and a two-wall system with a cross-vault. The comparative study offers a useful review of pushover analysis methods for masonry structures and shows advantages and possible limitations of each approach., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

In-plane cyclic loading of masonry walls strengthened by vegetal-fabric-reinforced cementitious matrix (FRCM) composites

  • Mercedes Cedeño, Luis Enrique
  • Bernat Masó, Ernest
  • Gil Espert, Lluís
Fabric-reinforced cementitious matrix (FCRMs) are promising composite materials for the retrofitting and reinforcement of existing structures. In this study, vegetal meshes consisting of hemp and cotton coated with epoxy were manufactured and combined with a cementitious matrix to strengthen masonry walls. A synthetic glass fibre mesh was also tested. Several walls were manufactured, strengthened, and tested under cyclic loading. The results allow us to compare the performances of different mesh configurations in terms of size and materials. All strengthening solutions significantly increased shear strength capacity and the ability to dissipate energy compared to unreinforced walls. Further, all strengthened walls exhibited multi-track pattern distributions and achieved distortion capacity improvements of up to 300%. Indicators of stiffness, energy dissipation, damping, residual deformation, and damage allow us to compare the strengthening performances of different solutions. The vegetal solutions provided superior efficiency compared to the glass-FRCM strengthened walls. Additionally, the use of a larger volume of vegetal fibres reduces the consumption of cement and can provide a sustainable solution. The main failure mechanism of the vegetal-FCRMs was debonding, which can be remedied by improvements to material interfaces., The authors gratefully acknowledge financial support from the Ministerio de Economía y Competitividad of the Spanish Government and the European Regional Development Fund through the MULTIMAS project (ref. num. BIA2015-63882-P). The first author also acknowledges the Ministry of Education Science and Technology of the Dominican Republic for financial support through its international scholarship program., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Dynamic elastic properties of brick masonry constituents

  • Makoond, Nirvan Chandra
  • Pelà, Luca
  • Molins i Borrell, Climent
When subjected to dynamic loading, materials can exhibit a mechanical behaviour quite different from its static counterpart. The evaluation of dynamic properties is thus very useful in the assessment of existing masonry structures. This paper presents results of an experimental campaign to determine both the dynamic Young’s modulus and the shear modulus of brick masonry constituents through two non-destructive testing methods. Following a discussion on the reliability of the methods, a robust procedure is described and tested on a variety of samples. The results show that the techniques can be successfully applied to provide reliable estimates of the dynamic elastic properties of brick masonry constituents., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Monotonic and cyclic testing of clay brick and lime mortar masonry in compression

  • Segura Domingo, Jorge
  • Pelà, Luca
  • Roca Fabregat, Pedro
This research presents an experimental programme on the mechanical characterization of masonry under monotonic and cyclic uniaxial compression. Two different types of standard specimens, running bond walls and stack bond prisms, were built using handmade clay bricks and hydraulic lime mortar. The experimental results are compared and discussed in terms of strength, stiffness and deformability. It was observed that the two specimen types provided very similar results on both strength and stiffness. Cyclic loading tests carried out on a set of samples provided new experimental evidence on the stiffness degradation, loss of load carrying capacity for increasing irreversible compressive strains and energy dissipation. The paper presents eventually a thorough discussion about the comparison between the obtained experimental results with available predictive models for strength, stiffness and fracture energy of masonry under monotonic and cyclic compression loading., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Tracking multi-directional intersecting cracks in numerical modelling of masonry shear walls under cyclic loading

  • Saloustros, Savvas
  • Cervera Ruiz, Miguel
  • Pelà, Luca
The final publication is available at Springer via http://dx.doi.org/10.1007/s11012-017-0712-3, In-plane cyclic loading of masonry walls induces a complex failure pattern composed of multiple diagonal shear cracks, as well as flexural cracks. The realistic modelling of such induced localized cracking necessitates the use of costly direct numerical simulations with detailed information on both the properties and geometry of masonry components. On the contrary, computationally efficient macro-models using standard smeared-crack approaches often result in a poor representation of fracture in the simulated material, not properly localized and biased by the finite element mesh orientation. This work proposes a possible remedy to these drawbacks of macro-models through the use of a crack-tracking algorithm. The macro-modelling approach results in an affordable computational cost, while the tracking algorithm aids the mesh-bias independent and localized representation of cracking. A novel methodology is presented that allows the simulation of intersecting and multi-directional cracks using tracking algorithms. This development extends the use of localized crack approaches using tracking algorithms to a wider field of applications exhibiting multiple, arbitrary and interacting cracking. The paper presents also a novel formulation including into an orthotropic damage model the description of irreversible deformations under shear loading. The proposed approach is calibrated through the comparison with an experimental test on a masonry shear wall against in-plane cyclic loading., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Propiedades mecánicas de compuestos de matriz cementicia reforzados con tejidos pretensados (PFRCM)

  • Bernat Masó, Ernest
  • Mercedes Cedeño, Luis Enrique
  • Gil Espert, Lluís
La matriz cementicia reforzada con tejidos (FRCM) es un material de refuerzo compuesto que se usa para reforzar estructuras de mampostería y de hormigón de forma pasiva, debido al requisito de activación de fisuras. Se propone pretensar el tejido para superar esta limitación, aumentar la resistencia a la fisuración y obtener una respuesta más rígida. Con este objetivo, se realizaron más de 200 ensayos de tracción en especímenes FRCM para analizar la influencia de los tejidos pretensados. También se analizaron otras variables, como el sistema de fijación, la velocidad de ensayo, el tipo de matriz y el tipo de tejidos. Las evidencias llevan a la conclusión de que pretensar el tejido del FRCM es una forma eficaz de aumentar su resistencia a la fisuración (más del 30%) y la rigidez a tracción., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Out-of-plane seismic response and failure mechanism of masonry structures using finite elements with enhanced strain accuracy

  • Vlachakis, Georgios
  • Cervera Ruiz, Miguel
  • Barbat Vlad, Gabriel
  • Saloustros, Savvas
The out-of-plane response is a complex and at the same time key aspect of the seismic vulnerability of masonry structures. It depends on several factors, some of which are the material properties, the quality of the walls, the geometry of the structure, the connections between structural elements and the stiffness of the diaphragms. During the last years, a wide variety of numerical methods has been employed to assess the out-of-plane behaviour of unreinforced masonry structures. Finite element macro-modelling approaches are among the most famous as they allow modelling large structures at a reasonable computational cost. However, macro-modelling approaches may result in a non-realistic representation of localized cracks and a dependency of the numerical solution on the finite element mesh. Mixed strain/displacement finite elements have been recently proposed as a remedy to the above nu-merical pathologies. Due to the independent interpolation of strains and displacements these finite element formulations are characterized by an enhanced accuracy in strain localization and crack propagation problems, being at the same time practically mesh independent. For these reasons, mixed finite elements are employed in this work for the out-of-plane assessment of unreinforced masonry struc-tures, being at the same time their first real-scale application. A full-scale experimental campaign of two masonry structures, a stone and a brick one, subjected to shaking-table tests is chosen as reference benchmark. Their structural response under seismic actions is numerically assessed through nonlinear static analysis. The proposed approach is validated through the comparison of the numerical results with the experimental ones, as well as with the results obtained using standard irreducible finite ele-ments., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Dynamic identification and static loading tests of timbrel vaults: application to a Modernist 20th century heritage structure

  • Endo, Yohei
  • Llorens Sulivera, Miquel
  • Roca Fabregat, Pedro
  • Pelà, Luca
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2017, available online at: http://www.tandfonline.com/10.1080/15583058.2016.1277566, This paper presents the study of the structural performance of a set of timbrel vaults belonging to the so-called Administration Pavilion of the Hospital de Sant Pau, a large-scale hospital complex located in Barcelona. The paper includes three parts. First, the Administration pavilion of Hospital de Sant Pau is described by putting the emphasis on the geometry of the masonry vaults and the combined utilisation of steel and masonry structural members. Second, laboratory and in-situ experiments are discussed. Finally, the behaviour observed during the dynamic-identification and the static-loading tests is simulated by means of FEM analysis. The FEM models prepared to analyse the vaults take explicitly into account the direct effect of secondary masonry structural elements, such as the upper slab and the extrados stiffening diaphragms. The comparison indicates that the consideration of these structural elements is essential for an adequate FEM simulation of both the dynamic and the static behaviour of the timbrel vaults., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental analysis of the size effect on the compressive behaviour of cylindrical samples core-drilled from existing brick masonry

  • Segura Domingo, Jorge
  • Pelà, Luca
  • Roca Fabregat, Pedro
  • Cabané Cañas, Albert
This paper presents the results of an experimental programme about the evaluation of the size effect on the compressive behaviour of cylindrical samples of existing masonry. The study focuses on the in-situ coring and experimental testing of core specimens with 150 mm and 90 mm diameter. The 150 mm cylinder, recurrent in minor destructive evaluation of the compressive strength of existing masonry, includes four brick pieces, two mortar beds and one head joint. The 90 mm specimen includes one mortar bed and two segments of brick, and inflicts less damage on the inspected structural member due to its lower invasivity. The experimental research investigates the size effect on four different types of clay brick masonry. The first type was built in the laboratory using historical-like materials. The other three types of masonry belong to structural walls of existing historical buildings. The combination of experimental results from laboratory controlled materials and existing historical members shows that the size of the cylindrical specimen has regular effect on the compressive strength and the Young’s modulus. The consistent relationship found between the compressive strengths of the 150 mm and 90 mm core samples allows the use of the latter specimen for a more respectful inspection of existing structural masonry., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Analytical derivation of seismic fragility curves for historical masonry structures based on stochastic analysis of uncertain material parameters

  • Saloustros, Savvas
  • Pelà, Luca
  • Contrafatto, Francesca Romana
  • Roca Fabregat, Pedro
  • Petromichelakis, Yiannis
This is an Accepted Manuscript of an article published by Taylor & Francis Group in International Journal of Architectural Heritage on 2019, available online at: http://www.tandfonline.com/10.1080/15583058.2019.1638992, This work presents a probabilistic method to assess the seismic vulnerability of historical masonry structures, such as churches or cathedrals, including uncertainty analysis of the material parameters. The proposed approach considers the pushover analysis using the finite element method for the structural evaluation of the seismic behaviour of masonry structures. A stochastic analysis based on Monte Carlo simulation investigates the effect of the uncertainty of the structural members’ mechanical parameters on the evaluation of the seismic fragility. The method is applied to the seismic assessment of the bay structure of Santa Maria del Mar church in Barcelona, Spain. This case study is characterised by complex geometry and material heterogeneity, and shows to be sensitive enough to the uncertainty of the material properties to experience two possible collapse mechanisms in case of an earthquake. The study presents how to derive analytical seismic fragility curves by considering the uncertainties regarding the material properties and the different types of collapse mechanism., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Building survey forms for heterogeneous urban areas in seismically hazardous zones: application to the historical center of Valparaíso, Chile

  • Jiménez, Belén
  • Pelà, Luca
  • Hurtado, Marcela
Building survey is an essential data-collection procedure to feed large-scale seismic vulnerability assessment. The available strategies usually consider survey forms to gather information about the urban buildings. The application of the available survey forms poses important challenges for the case of the heterogeneous urban centers including different structural typologies. This work proposes four specific survey forms for traditional structural typologies constructed with masonry, reinforced concrete, mixed steel-reinforced concrete, and timber. The proposed forms request essential information on the parameters necessary for seismic vulnerability assessment, by evaluating the lateral-load resistant system, regularity, condition of conservation, and existing damages. The survey forms were applied to the study of 111 buildings of the historical center of Valparaíso, Chile. The proposed methodology was complemented with the use of Geographic Information Systems to obtain a complete database with the structural characterization of the most representative typologies for future works of large-scale seismic vulnerability assessment., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Investigation on experimental techniques for the mechanical characterization of brick masonry

  • Roca Fabregat, Pedro
  • Pelà, Luca
One of the main difficulties found in the assessment and verification of masonry historical structures lays in the characterization of the main mechanical properties of the material components (units and mortar) and masonry as composite material. In an attempt to provide possible approaches for mechanical characterization, the paper presents and discusses different Minor Destructive Tests (MDTs) oriented to the measurement of the compressive strength of mortar bed joints and masonry composite samples extracted from existing brick masonries. The MDTs discussed for mortar characterization are the Double Punch Test (DPT), the Windsor Pin Penetration Test (PPT) and the Helix Screw Pull-Out Test (HPT). The method presented for the characterization of masonry as composite encompasses laboratory tests on cylindrical core samples. Different types of cylindrical samples, corresponding to alternative sizes and geometrical joint configurations, are investigated based on-purpose built laboratory walls and from a set of real case studies. The proposed MDTs are appraised with regard to their reliability and real applicability., The authors gratefully acknowledge the financial support provided by the Ministry of Economy and Competitiveness and from the Ministry of Science, Innovation and Universities (MCIU) of the Spanish Government and the State Agency of Research (AEI), as well as that of the European Regional Development Fund (FEDER) through projects MULTIMAS (BIA2015-63882-P) and SEVERUS (RTI2018-099589-B-I00)., Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.4 - Redoblar els esforços per a protegir i salvaguardar el patrimoni cultural i natural del món, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Influence of geometry of cylindrical samples in the mechanical characterization of existing brickwork

  • Segura, Jorge
  • Pelà, Luca
  • Roca Fabregat, Pedro
The mechanical characterization of masonry is of paramount importance for the structural assess-ment of historical constructions against both vertical and horizontal actions. In particular, the compressive strength of masonry is normally regarded as a critical parameter for structural analysis. However, an accurate determination of the mechanical properties of masonry is a difficult task due to the complex and heterogene-ous behavior of the material. The mechanical characterization of historical masonry is also hindered by the need to limit damage caused by inspection in culturally valuable buildings. Recent researches and standards point to the possibility of estimating the compressive strength of existing brickwork by testing cylindrical samples of at least 150 mm diameter extracted from the brickwork walls. This work investigates the possibility of carrying out similar tests on smaller diameter cylinders. Using smaller cyl-inders may allow the extraction of a larger amount of samples and also permit the reduction of the extent of damage caused to the building. This study presents a comparison between compression tests performed on 150 mm and 90 mm diameter cy-lindrical samples to evaluate the strength and stiffness of masonry consisting of lime mortar and clay bricks. The tests were carried out in the laboratory on samples extracted from masonry walls by using a dry core-drilling procedure and then regularized with high strength mortar caps. The experimental results show the re-lationship between the different geometries of core samples regarding strength values, failure modes and crack patterns. The study contributes to the application of experimental tests on cylindrical samples as a minor de-structive technique to estimate the mechanical parameters of historical brickwork under compression., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Torque Penetrometric Test for the in-situ characterisation of historical mortars: fracture mechanics interpretation and experimental validation

  • Marastoni, Diego
  • Benedetti, Andrea
  • Pelà, Luca
  • Pignagnoli, Giacomo
The assessment of historical structures requires appropriate knowledge of the behaviour of the investigated materials. Concerning masonry, its mechanical characterisation is a challenging task, since its composite nature requires the careful evaluation of the behaviour of its material components. In particular, the experimental assessment of the strength of existing mortar in historical structures still encounters several difficulties. This study investigates a novel Minor Destructive Testing (MDT) technique virtually equivalent to the vane test used for soils. The instrumentation, called herein Torque Penetrometric Test (TPT), is composed of a steel nail with four protruding teeth and a torque wrench. The test consists in inserting the toothed nail into a mortar joint and then applying a torque by means of a dynamometric key, until reaching the failure of the material. This work presents a novel interpretation theory based on basic concepts of fracture mechanics and applied to the micro-mechanical analysis of the stress state induced by the instrument on the investigated mortar. The proposed interpretative theory is validated through the execution of experimental tests in the laboratory and in a historical masonry building. The test proves to be effective for a quick in-situ MDT evaluation of the strength of existing mortars., Peer Reviewed, Postprint (author's final draft)