Pasar al contenido principal

DESARROLLO DE TECNICAS DE REFUERZO DE ESTRUCTURAS DE HORMIGON CON MATERIALES AVANZADOS Y SUS MODELOS MECANICOS DE COMPORTAMIENTO ESTRUCTURAL PARA LA EXTENSION DE SU VIDA UTIL

BIA2015-64672-C4-3-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDAD DE LAS ISLAS BALEARES
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Application of the Compression Chord Capacity Model to predict the fatigue shear strength of reinforced concrete members without stirrups

  • Cladera, Antoni
  • Ribas, Carlos
  • Oller, Eva
  • Marí, Antonio
The Compression Chord Capacity Model (CCCM), previously developed by the authors with other colleagues, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-section, which represents a useful tool for structural design and assessment in engineering practice. The principal advantage of the application of a mechanical model is the possibility to extend it to different cases, without the need of empirical calibrations. According to the CCCM, the shear strength depends on the concrete tensile strength. In this communication, the CCCM is extended to assess the fatigue shear strength of RC members just incorporating the equation proposed in Model Code 2010 for the concrete tensile fatigue strength. A good performance of the model was observed when analysing the ratio Vtest/Vpred through a previously published database, showing a low scatter (COV 14.7 %).
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Estudio experimental del efecto tamaño en la resistencia a cortante de elementos de hormigón

  • Varela-Puga, Fernando
  • Herrador, Manuel
  • Martínez-Abella, Fernando
  • Paredes González, Manuel
  • Eiras López, Javier
[Resumen]: El comportamiento de elementos de hormigón a cortante es y ha sido en la última época un tema de constante debate en el área de la ingeniería estructural. Existe gran distancia entre la realidad del fenómeno y la interpretación de las normativas, que suelen proporcionar expresiones semi-empíricas con ajustes basados en análisis estadísticos. Dentro de este paradigma, asociado principalmente a elementos de hormigón armado, la reducción de la tensión tangencial media resistida a medida que aumenta su dimensión representativa, fenómeno conocido como efecto tamaño, se alza como uno de los aspectos a los que es necesario aportar más información empírica. Sin embargo, la experimentación en este campo es reducida debido a la dificultad de este tipo de ensayos en escalas representativas. Es en este punto donde se han centrado los esfuerzos de esta investigación, intentando identificar y cuantificar los mecanismos resistentes que aparecen en un elemento sometido a grandes solicitaciones tangenciales. Para ello, se ha realizado una campaña experimental sobre vigas de gran canto: 1.00 m (serie S), 1.50 m (serie M) y 2.00 m (serie L) de canto con longitud suficiente no incurrir en un efecto arco y, así mismo, poder realizar un ensayo a cortante sobre cada vano. Durante los ensayos se ha monitorizado y medido de manera directa (extensometría clásica) e indirecta (videocorrelación) los posibles mecanismos resistentes analizados en la bibliografía relativa: cabeza de compresión, armadura, armadura longitudinal y transmisión de tensiones en la fisura principal. El presente documento expone los resultados de la campaña experimental descrita. Además se realiza un estudio de la situación existente a día de hoy de la relación entre la realidad de la capacidad resistente a cortante de elementos de grandes dimensiones y las interpretaciones realizadas por las normativas vigentes., [Abstract]: The behaviour of concrete elements subjected to shear stress is and has been in recent time subject of constant discussion on structural engineer area. There is a great distance between the reality of the phenomenon and the standards interpretation, which tend to propose semi-empiric expressions with adjustments based on statistical analysis. Within this paradigm, mainly associated with reinforced concrete elements, the reduction of the average shear stress capacity as their characteristic dimension increases— known as the size effect—emerges as one of the aspects that requires further empirical evidence. However, experimental research in this field is limited due to the difficulty of conducting tests at representative scales. It is at this point where the efforts of the present research have been focused, aiming to identify and quantify the resisting mechanisms that develop in an element subjected to high shear demands. To this end, an experimental campaign was carried out on deep beams with depths of 1.00 m (Series S), 1.50 m (Series M), and 2.00 m (Series L), with sufficient span length to avoid arching effects and to allow for shear testing in each span. During the tests, the possible resisting mechanisms discussed in the literature were monitored and measured both directly (using conventional strain gauges) and indirectly (through digital image correlation), including the compression strut, transverse reinforcement, longitudinal reinforcement, and stress transfer across the main crack. This document presents the results of the described experimental campaign. In addition, it includes an analysis of the current state of the relationship between the actual shear capacity of large-scale elements and the interpretations provided by existing design codes., Los autores de este documento agradecen a las universidades de A Coruña (UDC), Universidad Politécnica de Cataluña (UPC), Illes Balears (UIB) y Universidad Politécnica de Valencia (UPV), sedes de los grupos de investigación que han realizado este estudio y los medios experimentales que han puesto a su disposición. La investigación ha sido posible gracias al proyecto coordinado HORVITAL (Referencias: BIA2015-64672-C4-4-R; BIA2015-64672-C4-3-R), financiado por el Ministerio de Economía, Industria y Competencia.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Shear fatigue strength of reinforced concrete members without transverse reinforcement according to the compression chord capacity model

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
Although the shear fatigue behaviour of elements without shear reinforcement has been studied for a while, there is still a need for a simple mechanical model that evaluates the shear fatigue strength. The Compression Chord Capacity Model (CCCM), previously developed by the authors, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-sections. This model represents a useful tool for structural design and assessment in engineering practice. In this paper, the CCCM has been extended to assess the fatigue shear strength of RC elements. This extension is consistent since the existing observed fatigue failure modes show similarities with the initial assumption of the model, which considers that the member shear strength is controlled by the shear capacity of the flexural compression chord. Three different approaches to take into account the influence of the fatigue have been combined with the CCCM. In general, a good performance of the model combined with the three different approaches was observed when analysing the ratio Vtest/Vpred through a database of 87 tests previously published by other authors, showing a low scatter (<15%) and a significant safety given by the minimum ratio and the 5th percentile., The authors want to acknowledge the financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through research projects: BIA2015-64672-C4-3-R and BIA2015-64672-C4-1-R. The authors also want to thank to Dr. Miguel Fernández-Ruiz for providing the authors the fatigue shear tests database., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Capítulo o parte de un libro (BookPart)

SP-357—8: Punching-shear strength of reinforced concrete slabs subjected to concentric transverse loads and in-plane tensile forces

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Cladera Bohigas, Antoni
Reinforced concrete slabs can be subjected simultaneously to transverse loads and in-plane tensile forces, as it occurs in top slabs of continuous box girder bridges at intermediate supports, or in flat slabs supported on columns, subjected to horizontal loads. To study the effects of in-plane forces in the slab punching-shear strength, an experimental and theoretical investigation was carried out, which is described in this paper. Five square slabs of 1650 mm (42”) side and 120 mm (4.7”) thickness were tested under a centered transverse point load and different degrees of uniaxial in-plane tensile force. Numerical predictions using non-linear finite element analyses were performed to help in the experiments design. Furthermore, the punching-shear mechanical model, Compression Chord Capacity Model (CCCM), was extended to incorporate the effects of in-plane tensile forces. The experimental results showed that the punching strength linearly decreases with the level of applied tensile force and, if cracking in the slabs is produced by the tensile force, yielding of the reinforcement and further reduction may take place. Excellent agreement was found between theoretical predictions and tests results. Furthermore, the CCCM was verified with available results of punching tests with uniaxial and biaxial tensile forces, obtaining very good results., This work has been carried out within the framework of research projects BIA-2015-64672-C4-1-R, and BIA2015- 64672-C4-3-R financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and also with the financial support of the Government of Catalonia through the contract for research and innovation in infrastructures E1-INF-18500. The authors want to deeply thank also the personnel of the Structural Technology Laboratory of the Universitat Politècnica de Catalunya.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Application of the Compression Chord Capacity Model to predict the fatigue shear strength of reinforced concrete members without stirrups

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
The Compression Chord Capacity Model (CCCM), previously developed by the authors with other colleagues, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-section, which represents a useful tool for structural design and assessment in engineering practice. The principal advantage of the application of a mechanical model is the possibility to extend it to different cases, without the need of empirical calibrations. According to the CCCM, the shear strength depends on the concrete tensile strength. In this communication, the CCCM is extended to assess the fatigue shear strength of RC members just incorporating the equation proposed in Model Code 2010 for the concrete tensile fatigue strength. A good performance of the model was observed when analysing the ratio Vtest/Vpred through a previously published database, showing a low scatter (COV 14.7 %)., Esta investigación se ha desarrollado en el marco de dos proyectos cofinanciados por la Agencia Estatal de Investigación y Fondos FEDER: BIA2015-64672-C4-3-R y BIA2015-64672-C4-1-R.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Application of the Compression Chord Capacity Model to predict the fatigue shear strength of reinforced concrete members without stirrups

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva
  • Marí Bernat, Antonio Ricardo
The Compression Chord Capacity Model (CCCM), previously developed by the authors with other colleagues, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-section, which represents a useful tool for structural design and assessment in engineering practice. The principal advantage of the application of a mechanical model is the possibility to extend it to different cases, without the need of empirical calibrations. According to the CCCM, the shear strength depends on the concrete tensile strength. In this communication, the CCCM is extended to assess the fatigue shear strength of RC members just incorporating the equation proposed in Model Code 2010 for the concrete tensile fatigue strength. A good performance of the model was observed when analysing the ratio Vtest/Vpred through a previously published database, showing a low scatter (COV 14.7 %)., Esta investigación se ha desarrollado en el marco de dos proyectos cofinanciados por la Agencia Estatal de Investigación y Fondos FEDER: BIA2015-64672-C4-3-R y BIA2015-64672-C4-1-R., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Shear fatigue strength of reinforced concrete members without transverse reinforcement according to the compression chord capacity model

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva
  • Marí Bernat, Antonio Ricardo
Although the shear fatigue behaviour of elements without shear reinforcement has been studied for a while, there is still a need for a simple mechanical model that evaluates the shear fatigue strength. The Compression Chord Capacity Model (CCCM), previously developed by the authors, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-sections. This model represents a useful tool for structural design and assessment in engineering practice. In this paper, the CCCM has been extended to assess the fatigue shear strength of RC elements. This extension is consistent since the existing observed fatigue failure modes show similarities with the initial assumption of the model, which considers that the member shear strength is controlled by the shear capacity of the flexural compression chord. Three different approaches to take into account the influence of the fatigue have been combined with the CCCM. In general, a good performance of the model combined with the three different approaches was observed when analysing the ratio Vtest/Vpred through a database of 87 tests previously published by other authors, showing a low scatter (<15%) and a significant safety given by the minimum ratio and the 5th percentile., The authors want to acknowledge the financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through research projects: BIA2015-64672-C4-3-R and BIA2015-64672-C4-1-R. The authors also want to thank to Dr. Miguel Fernández-Ruiz for providing the authors the fatigue shear tests database., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación

SP-357—8: Punching-shear strength of reinforced concrete slabs subjected to concentric transverse loads and in-plane tensile forces

  • Marí Bernat, Antonio Ricardo
  • Fernández Sánchez, Pablo Gonzalo
  • Oller Ibars, Eva
  • Cladera Bohigas, Antoni
Reinforced concrete slabs can be subjected simultaneously to transverse loads and in-plane tensile forces, as it occurs in top slabs of continuous box girder bridges at intermediate supports, or in flat slabs supported on columns, subjected to horizontal loads. To study the effects of in-plane forces in the slab punching-shear strength, an experimental and theoretical investigation was carried out, which is described in this paper. Five square slabs of 1650 mm (42”) side and 120 mm (4.7”) thickness were tested under a centered transverse point load and different degrees of uniaxial in-plane tensile force. Numerical predictions using non-linear finite element analyses were performed to help in the experiments design. Furthermore, the punching-shear mechanical model, Compression Chord Capacity Model (CCCM), was extended to incorporate the effects of in-plane tensile forces. The experimental results showed that the punching strength linearly decreases with the level of applied tensile force and, if cracking in the slabs is produced by the tensile force, yielding of the reinforcement and further reduction may take place. Excellent agreement was found between theoretical predictions and tests results. Furthermore, the CCCM was verified with available results of punching tests with uniaxial and biaxial tensile forces, obtaining very good results., This work has been carried out within the framework of research projects BIA-2015-64672-C4-1-R, and BIA2015- 64672-C4-3-R financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and also with the financial support of the Government of Catalonia through the contract for research and innovation in infrastructures E1-INF-18500. The authors want to deeply thank also the personnel of the Structural Technology Laboratory of the Universitat Politècnica de Catalunya., Postprint (author's final draft)