Pasar al contenido principal

EVALUACION EXPERIMENTAL DE VIGAS CONTINUAS PRETENSADAS, CON Y SIN REFUERZO, Y PIEZAS COMPUESTAS DE DOS HORMIGONES, PARA LA EXTENSION DE SU VIDA UTIL.

BIA2015-64672-C4-4-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the shear strength mechanism of slender precast concrete beams with cast-in-place slab and web reinforcement

  • Rueda-García, Lisbel|||0000-0002-2061-1656
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] Precast concrete beams with cast-in-place slabs on top, namely concrete composite beams are frequently used for building concrete bridge decks. In designs, the contribution of cast-in-place slabs to shear strength tends to be omitted. However, given the vast number of existent bridges with this deck typology, significant cost savings could be made when assessing these structures if the slab's shear strength is considered. This paper analyses how cast-in-place slab influences the shear behaviour of concrete composite beams with web reinforcement. For this purpose, an experimental programme of 18 concrete specimens with web reinforcement and rectangular crosssections was run, in which the following parameters varied: cross-sectional depth; existence of an interface between concretes; compressive strengths of the concrete of beams and slabs; differential shrinkage between concretes. It was observed that: the slab contributed to resist shear; the existence of an interface between concretes led to a crack appearing along it that caused the transmitted shear to be divided into two load paths: one through the precast beam and another one through the slab; the slab's concrete strength was that which mainly influenced the element's shear strength; differential shrinkage did not reduce shear strength. Based on experimental observations, a mechanical model is proposed in this paper to assess the composite elements' shear strength, which considers the yielding of both stirrups and the slab's longitudinal reinforcement to be a failure criterion, which well predicted the experimental results. The shear formulations of Eurocode 2, the Level III Approximation of Model Code 2010 and the (b) Formula of ACI 318-19 offered a similar result to the herein proposed method when using the entire composite element effective depth and the weighted average of the concrete strengths of both the beam and slab estimated from the area ratio. Codes significantly underestimated specimens' interface shear., The experimental programme of this research work was undertaken at the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politecnica de Valencia (UPV; Spain) with concrete supplied by Caplansa. The project was supported by the Spanish Min-istry of Science and Innovation through Projects BIA2015-64672-C4-4-R and RTI2018-099091-B-C21-AR; the Regional Government of Valencia through Project AICO/2018/250; the European Union with FEDER funds. The authors thank the Spanish Ministry of Economy and Business for Grant BES-2016-078010 that supported Lisbel Rueda-Garcia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Experimental Assessment of the Shear Resistant Behaviour of Precast Concrete Beams with Top Cast-in-Place Concrete Slab

  • Rueda-García, Lisbel|||0000-0002-2061-1656
[ES] La construcción con elementos prefabricados de hormigón es un sector en alza por la aceleración del proceso constructivo, el ahorro de costes derivados de la obra in situ y la mejora de la calidad y acabados, entre otros. En la construcción prefabricada de estructuras de ingeniería civil como puentes y edificios es frecuente el empleo de vigas prefabricadas de hormigón. La construcción con estas vigas requiere el vertido de una capa de hormigón in situ sobre las mismas tras su emplazamiento, que sirve como elemento integrador para garantizar la unidad estructural. Los elementos estructurales que se obtienen de esta forma son conocidos como vigas compuestas de hormigón. En vigas compuestas, aspectos como la resistencia a rasante de la interfaz entre hormigones han sido estudiados en numerosas publicaciones. No obstante, su comportamiento a cortante no ha sido, por el momento, analizado en profundidad. En consecuencia, existe muy poca información, tanto en la literatura existente como en los códigos de diseño actuales, acerca de la resistencia a cortante de estos elementos, de cómo influye la presencia de una interfaz entre los hormigones en la resistencia a cortante o de cómo contribuye la losa hormigonada in situ a dicha resistencia. La presente tesis doctoral tiene como objetivo estudiar la resistencia a cortante de vigas compuestas de hormigón. Para ello, se desarrolla un extenso programa experimental compuesto por vigas monolíticas y compuestas con y sin armadura transversal, con sección transversal rectangular o en forma de T y con hormigones de diferentes calidades en la viga prefabricada y en la losa hormigonada in situ. Se ensaya a cortante un total de 69 vigas de hormigón armado con el fin de analizar las diferentes variables de interés en la resistencia a cortante. A partir de los resultados experimentales, se propone un modelo mecánico de predicción de la resistencia a cortante de vigas compuestas de hormigón con sección transversal rectangular y en forma de T, que también es de aplicación a vigas monolíticas en T. Además, como apoyo al estudio experimental y al modelo mecánico, se modelan numéricamente algunos especímenes del programa experimental. Con todo ello, se busca incrementar el estado actual del conocimiento en este campo, mediante el aporte de un gran número de resultados experimentales y el análisis de los parámetros de diseño, así como sentar las bases para el desarrollo de una formulación de diseño de estructuras compuestas y de evaluación de las ya existentes globalmente aceptada por la comunidad científica., [CA] La construcció amb elements prefabricats de formigó és un sector en alça per l'acceleració del procés constructiu, l'estalvi de costos derivats de l'obra in situ i la millora de la qualitat i acabats, entre altres. En la construcció prefabricada d'estructures d'enginyeria civil com a ponts i edificis és freqüent l'ús de bigues prefabricades de formigó. La construcció amb aquestes bigues requereix l'abocament d'una capa de formigó in situ sobre les bigues després del seu emplaçament, que serveix com a element integrador per a garantir la unitat estructural. Els elements estructurals que s'obtenen d'aquesta forma són coneguts com a bigues compostes de formigó. En bigues compostes, aspectes com la resistència a rasant de la interfície entre formigons han sigut estudiats en nombroses publicacions. No obstant això, el seu comportament a tallant no ha sigut, de moment, analitzat en profunditat. En conseqüència, existeix molt poca informació, tant en la literatura existent com en els codis de disseny actuals, sobre la resistència a tallant d'aquests elements, de com influeix la presència d'una interfície entre els formigons en la resistència a tallant o de com contribueix la llosa formigonada in situ a aquesta resistència. La present tesi doctoral té com a objectiu estudiar la resistència a tallant de bigues compostes de formigó. Per a això, es desenvolupa un extens programa experimental compost per bigues monolítiques i compostes amb armadura transversal i sense, amb secció transversal rectangular o en forma de T i amb formigons de diferents qualitats en la biga prefabricada i en la llosa formigonada in situ. S'assaja a tallant un total de 69 bigues de formigó armat amb la finalitat d'analitzar les diferents variables d'interés en la resistència a tallant. A partir dels resultats experimentals, es proposa un model mecànic de predicció de la resistència a tallant de bigues compostes de formigó amb secció transversal rectangular i en forma de T, que també és aplicable a bigues monolítiques en T. A més, com a suport a l'estudi experimental i al model mecànic, es modelen numèricament alguns espècimens del programa experimental. Amb tot això, es pretén incrementar l'estat actual del coneixement en aquest camp, mitjançant l'aportació d'un gran nombre de resultats experimentals i l'anàlisi dels paràmetres de disseny, així com establir les bases per al desenvolupament d'una formulació de disseny d'estructures compostes i d'avaluació de les ja existents globalment acceptada per la comunitat científica., [EN] Construction with precast concrete elements is a booming sector due to the acceleration of the construction process, the saving of costs arising from the on-site construction and the quality and finish improvement, among others. Precast concrete beams are frequently used in the precast construction of civil engineering structures such as bridges and buildings. Construction with these beams requires the pouring of a cast-in-place concrete layer on top of the beams after their placement, which works as a unifying element to ensure structural integrity. Structural elements obtained in this way are known as concrete composite beams. In composite beams, some aspects such as the shear strength of the interface between concretes have been studied in multiple publications. However, their shear behaviour has not yet been analysed in depth. Consequently, there is very little information, both in the existing literature and in current design codes, about the shear strength of these elements, how the presence of an interface between the concretes influences the shear strength or how the cast-in-place concrete slab contributes to the shear strength. The aim of this doctoral thesis is to study the shear strength of concrete composite beams. For this purpose, an extensive experimental programme is developed, consisting of monolithic and composite beams with and without transverse reinforcement, with rectangular or T-shaped cross-section and with concretes of different qualities in the precast beam and in the slab. A total of 69 reinforced concrete beams are tested under shear forces in order to analyse the different variables of interest in shear strength. Based on the experimental results, a mechanical model for predicting the shear strength of concrete composite beams with rectangular and T-shaped cross-section is proposed, which is also applicable to monolithic T-beams. In addition, to support the experimental study and the mechanical model, some specimens of the experimental programme are numerically modelled. All in all, the aim is to improve the current state of knowledge in this field by providing a large number of experimental results and analysing the design parameters, as well as to lay the foundations for the development of a formulation for the design of existing structures and the assessment of existing ones that is globally accepted by the scientific community., The present doctoral thesis would not have been possible without the financial support of the Ministerio de Ciencia e Innovación (MCIN) and the Agencia Estatal de Investigación (AEI) through Grants BIA2015-64672-C4-4-R and RTI2018- 099091-B-C21-AR, both funded by MCIN/AEI/10.13039/501100011033 and by the “ERDF A way of making Europe”. I am thankful as well for their support through Grant BES-2016-078010 funded by MCIN/AEI/10.13039/501100011033 and by the “ESF Investing in your future”. The project was also supported by the Regional Government of Valencia through Project AICO/2018/250. And finally, thanks to the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politècnica de València (UPV; Spain) in which this research project has been developed, and to our concrete supplier Caplansa.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of the plastic hinge rotations on shear strength in continuous reinforced concrete beams with shear reinforcement

  • Monserrat López, Andrea
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] Continuous reinforced concrete (RC) beams may develop significant plastic rotations to enable the redistribution of bending moments. These rotations occur at plastic hinges, which are subject to high shear forces. The influence of rotations on the shear strength for statically determined beams without shear reinforcement failing in shear after yielding of the flexural reinforcement has already been experimentally verified. However, this influence has not been studied in continuous members with shear reinforcement. An innovative tests system has been specially designed to develop shear failures before and after yielding of the flexural reinforcement in both statically determinate and indeterminate structures. Nine beams (9000 mm long, 250 mm wide, 450 mm high) with a shear reinforcement of phi 8/30 (rho(w) = 0.13%) and different longitudinal reinforcement ratios were tested under different load and support conditions. The shear strength provided by shear reinforcement and that provided by the other mechanisms of resistance (shear strength provided by concrete) for each specimen were calculated based on the critical shear crack width measurements performed by Digital Image Correlation (DIC). Bending rotation and crack rotation along the development length of the critical shear crack were also obtained by DIC. Based on the test results, the shear strength provided by concrete was studied in relation to the bending rotation and the average crack width in reinforced concrete beams with shear reinforcement. It was confirmed that the shear strength provided by concrete decreased with increasing both bending rotations and crack widths. The shear strength values predicted by different design codes (ACI 318-19, Eurocode 2 and Model Code 2010) were compared with the test results, and showed that these formulations did not properly capture the loss of shear strength caused by bending rotation., This research was funded with grants from the Spanish Ministry of Economy and Competitiveness to Research Project BIA2015-64672-C4-4-R. The experimental programme was developed in the Laboratory of Concrete of the Institute of Concrete Science and Technology (ICITECH) of the Universitat Politecnica de Valencia (UPV), with concrete supplied by Caplansa. Andrea Monserrat was supported by the Conselleria d'Educacio, Investigacio, Cultura i Esport of the Generalitat Valenciana (Order 6/2015, DOCV no. 7615 15.09.2015) with European Regional Development Funds (ERDF) allocated by the EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The influence of transverse reinforcement and yielding of flexural reinforcement on the shear-transfer actions of RC members

  • Monserrat López, Andrea
  • Fernánez Ruiz, Miguel
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
[EN] The assessment of the shear strength of reinforced concrete beams with and without shear reinforcement is investigated in this paper on the basis of the contribution of the various potential shear-transfer actions. To that aim, a comprehensive experimental programme is presented, aimed at representing realistic conditions in reinforced concrete members. The programme comprised 15 cantilevers and 15 continuous beams with and without stirrups. In addition, some of the tests were designed to fail in shear after yielding of the flexural reinforcement, allowing to investigate on the structural implications of this phenomenon. The tests were instrumented by means of surface measurements using Digital Image Correlation (DIC), tracking in a detailed manner the development and kinematics of the critical shear crack leading to failure. Based on these mea-surements, and by accounting for suitable constitutive models, the contribution of the shear-transfer actions is estimated at different levels of load. The comparison of the experimental results with the calculated shear strength (sum of the contribution of the various shear-transfer actions at failure) shows consistent agreement for the various cases investigated. On this basis, several conclusions about the dominant shear-transfer actions at shear failure are presented, particularly on the role of the shear reinforcement and on the implications of the flexural reinforcement yielding on the overall response., This research was funded by grants from the Spanish Ministry of Economy and Competitiveness to Research Project BIA2015-64672-C4-4-R. The experimental programme was developed in the Laboratory of Concrete at the Institute of Concrete Science and Technology (ICITECH) of the Universitat Politecnica de Valencia (UPV), with concrete supplied by Caplansa. Andrea Monserrat was supported by the Conselleria d'Educacio, Investigacio, Cultura i Esport of the Generalitat Valenciana (Order 6/2015, DOGV no. 7615 15.09.2015) with European Regional Development Funds (ERDF) allocated by the EU. VIC2D software was employed during the research stay of Andrea Monserrat at the EPFL (Lausanne, Switzerland).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of shear strength in continuous reinforced concrete beams with and without shear reinforcement

  • Monserrat López, Andrea
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] Shear strength of reinforced concrete beams has been extensively studied by many experimental campaigns conducted on simply supported beams. This situation has led to implement empirical design formulations in codes that cannot be representative of other real structures, such as continuous beams. These structures are characterised by the potential development of plastic hinges in areas of maximum shear and by the existence of an inflection point in the shear span. However, very few experimental studies on them have been conducted. In this paper, the shear strength of cantilever and continuous beams with different shear reinforcement ratios is analysed based on the test results of an experimental programme involving 15 beams. Nine beams of 9.00 m and six of 7.00 m with rectangular cross-sections were tested under different load and support conditions, which gave rise to 30 different shear tests (two tests per beam). Three different series were considered according to the shear reinforcement ratio (0%, 0.13% and 0.20%). Apart from traditional instrumentation, such as strain gauges and displacement transducers, Digital Image Correlation was employed to provide accurate displacement measurements. The results showed that the shear strength provided by concrete (different shear-transfer actions from shear reinforcement) decreased as bending rotation increased within both the elastic and plastic ranges of rotations developed in continuous beams. Moreover, this shear strength component was reduced for increasing shear reinforcement ratios. Shear slenderness was redefined for continuous beams that failed in shear after yielding of the tensile reinforcement and redistributing internal forces. The code formulation provided by ACI 318-19, Eurocode 2 and Model Code 2010 was checked against the experimental results, which showed that the iterative formulation that contemplates the M-V interaction considerably improved shear strength predictions from simple formulations., This research was funded by grants from the Spanish Ministry of Economy and Competitiveness to Research Project BIA2015-64672-C4-4-R. The experimental programme was developed in the Laboratory of Concrete at the Institute of Concrete Science and Technology (ICITECH) of the Universitat Politecnica de Valencia (UPV), with concrete supplied by Caplansa. Andrea Monserrat was supported by the Conselleria d'Educacio, Investigacio, Cultura i Esport of the Generalitat Valenciana (Order 6/2015, DOCV no. 7615 15.09.2015) with European Regional Development Funds (ERDF) allocated by the EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Safety Assessment of Shear Strength Current Formulations for Composite Concrete Beams without Web Reinforcement

  • Rueda-García, Lisbel|||0000-0002-2061-1656
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] Construction with precast concrete elements without web reinforcement and cast-in-place concrete on them to enhance the overall structure's integrity is a widespread practice in building construction. However as these composite elements' vertical shear strength has not been studied in-depth, a clear criterion about cast-in-place concrete's contribution to shear resistance is still a pending matter. The present study intends to reach practical conclusions about the shear strength assessment of composite concrete elements without web reinforcement. To do so, the shear strengths of 36 specimens, provided by existing shear formulations, were compared: 19 specimens tested by the authors, in which the existence of an interface between concretes, the cross-sectional shape and the concrete compressive strengths of the beam and slab were studied; and 17 specimens taken from a previous study about composite elements by Kim et al. (2016). The applied shear formulations were those of EC2-04, Draft 7 of EC2-20, fib MC-10, ACI 318-19 and the model proposed by Kim et al. (2016). Firstly, specimens' shear strength was calculated by considering that only the beam resisted shear. Secondly according to ACI 318-19 indications about assessing composite elements¿ shear strength, the entire composite element's effective depth was used considering the lower of the compressive strengths of the beam's and slab's concretes and the weighted average of the compressive strengths. Additionally,the entire effective depth and the beam's concrete compressive strength were used. Codes formulations were more precise when estimating the monolithic specimens' shear strengths than those of composites. Therefore, the development of an adapted methodology to assess these elements¿ shear strengths is needed. EC2-20 obtained the most accurate results and gave quite good estimations for composite elements when the entire effective depth and weighted average of the concretes compressive strengths were considered., This study forms part of the research conducted at the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politècnica de València (UPV, Spain) with concrete supplied by Caplansa. The project has been supported by the Spanish Ministry of Science and Innovation through Projects BIA2015-64672-C4-4-R and RTI2018-099091-B-C21-AR; the Regional Government of Valencia through Project AICO/2018/250, and the European Union with FEDER funds. The authors thank the Spanish Ministry of Economy and Business for Grant BES-2016-078010.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Shear strength assessment of RC members: influence of shear reinforcement and yielding of the flexural reinforcement

  • Monserrat López, Andrea
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
[EN] An extensive experimental programme consisting of 15 shear tests on continuous reinforced concrete beams was carried out to assess the shear strength of beams with and without shear reinforcement. The influence of large flexural strains in the shear strength was analysed as the tests were designed to fail in shear after yielding of the flexural reinforcement. The assessment of the shear strength was investigated based on the contribution of the various potential shear-transfer actions following the possibilities offered by Digital Image Correlation (DIC). In this field, several approaches accounting for the role of the various shear-transfer actions have recently been proposed, such as the Critical Shear Crack Theory or the Compression Chord Capacity Model, and significant advances on the analysis of the activation of these shear-transfer actions have been performed by the use of DIC. In this work, detailed surface displacement measurements were performed by means of DIC, allowing to track the development and kinematics of the critical shear crack leading to failure. Based on this information, together with suitable constitutive models, the amount of shear transferred by each shear-transfer action was estimated at different load levels and at failure. The calculated shear strength of the specimens was obtained as the sum of the contribution of the various shear-transfer actions at failure and its comparison with the experimental results showed consistent agreement for the different cases. Based on the results, different conclusions and implications about the contribution of the various shear-transfer actions at shear failure are presented. In general, the contribution of each shear-transfer action is strongly influenced by cracking patterns and by the location, shape and kinematics of the critical shear crack., This research was funded through grants from the Ministerio de Economía y Competitividad of Spain with the research project BIA2015-64672-C4-4-R. The experimental program was developed in the Laboratory of Concrete of the Institute of Concrete Science and Technology (ICITECH) of the Universitat Politècnica de València (UPV). Andrea Monserrat has been particularly supported by the Conselleria d'Educació, Investigació, Cultura i Esport of Generalitat Valenciana (Orden 6/2015, DOCV n. 7615 15.09.2015) with the European Regional Development Fund (ERDF) allocated by the EU. VIC2D software was employed during the research stay of Andrea Monserrat at the EPFL (Lausanne, Switzerland).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental analysis of the shear resistance of precast concrete T-beams with a top cast-in-place slab

  • Rueda-García, Lisbel|||0000-0002-2061-1656
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] Precast concrete T-beams with a cast-in-place slab on top are structural elements that are often employed in composite construction. Despite their widespread use, some aspects of their structural behaviour upon shear forces have not yet been studied in depth. Six composite specimens with different T-shaped cross-sections and concrete qualities, and with web reinforcement, were tested to analyse the shear transfer mechanisms and to assess the contribution of the cast-in-place slab to shear strength. The shear strength mechanisms deriving from experimental observations and measurements are provided. This study indicates that: placing a concrete cast-in-place slab on top of a prefabricated T-beam increases its shear strength; interface shear strength plays an essential role in concrete composite elements¿ vertical shear strength; widening the cast-in-place slab width does not increase shear strength in this test programme specimens; the compressive strength of the precast beam¿s concrete significantly influences composite beams¿ shear resistances. The ACI 318-19 formulation best captures the influence of concrete strength on shear strength of the three formulations considered (EC2, MC-10 (Level III) and ACI 318-19). However, all of them tend to underestimate shear strengths compared to the experimental results., Ministerio de Ciencia e Innovacion (MCIN) and Agencia Estatal de Investigacion (AEI) supported the present research work through grants BIA2015-64672-C4-4-R and RTI2018-099091-B-C21-AR, both funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe". Author Lisbel Rueda-Garcia was supported by grant BES -2016-078010 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future". The project was also carried out with the support of the Regional Government of Valencia through Project AICO/2018/250. The open access charge was funded by CRUE- Universitat Politecnica de Valencia. This research work was under- taken at the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politecnica de Valencia (UPV; Spain) with concrete supplied by Caplansa.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental analysis of the shear strength of composite concrete beams without web reinforcement

  • Rueda-García, Lisbel|||0000-0002-2061-1656
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] Composite concrete members without web reinforcement are often used in precast construction. The contribution of the cast-in-place concrete topping slab to vertical shear strength has been traditionally disregarded. However, significant cost savings can result from designing and assessing these structures if this contribution is considered. This paper presents the experimental study of a series of 21 monolithic and composite (precast beam and cast-in-place slab) specimens without web reinforcement, and with rectangular and T-shaped cross-sections, failing in shear. The vertical shear strength was analysed by the following test variables: cross-section shape, the existence of an interface between different aged concretes, strengths of the two concretes and the differential shrinkage effect. From these experimental tests, it was concluded that the slab contributed to shear strength, the use of high-strength concrete slightly increased specimens' shear strength and the differential shrinkage did not reduce shear strength. Specimens' failure modes were analysed based on their shear transfer mechanisms, noticing that the arching action in the slab was considerable after critical shear crack formation. The vertical shear strength experimental results were well predicted by the codes' formulations (Eurocode 2, Model Code 2010 and ACI 318-19) when composite beam depth was taken for the calculations instead of beam depth. Codes significantly underestimated the horizontal shear strengths of the composite specimens., This research has been supported by: the Spanish Ministry of Science and Innovation through Research Project BIA2015-64672-C4-4-R and RTI2018-099091-B-C21-AR; the Regional Government of Valencia through Project AICO/2018/250; the European Union with FEDER funds. The experimental programme was developed in the Laboratory of Concrete of the Institute of Concrete Science and Technology (ICITECH) of the Universitat Politècnica de València (UPV) with concrete supplied by Caplansa. The Spanish Ministry of Science and Innovation supported Lisbel Rueda through grant BES-2016-078010.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study on the shear strength of reinforced concrete composite T-shaped beams with web reinforcement

  • Rueda-García, Lisbel|||0000-0002-2061-1656
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] The current increasing use of precast concrete elements and cast-in-place concrete slabs, namely concrete composite elements, in construction requires a better understanding of their behaviour in shear. In this work, 19 T-shaped composite and monolithic specimens failing in shear were experimentally tested. Their results were compared to study the influence on the shear strength of: the flange width, the presence of an interface between concretes and the strength of the concretes of both beam and slab. The shear transfer mechanisms were analysed by adapting to these specimens a mechanical model previously proposed by the authors for rectangular composite beams. It was concluded that: the composite specimens¿ shear strength did not increase with widening flange width when the specimens showed an extended interface cracking, but increased when their crack pattern was similar to that of the monolithic specimens; the presence of an interface decreased the shear strength; the slab¿s concrete compressive strength modified the composite specimens¿ shear strength when the slab failed in shear, but not when the slab failed in bending or when the interface failed. The shear formulations of EC2, MC-10 Level III and ACI 318-19 gave good estimations when using the weighted average of the compressive strengths of the beam and slab concretes, similarly to those obtained with the proposed model. From the experimental results, the improvement of the interface shear strength of composite beams is proposed as a practical recommendation for increasing their shear strength. At the same time, the slab width and the slab¿s concrete strength could be increased with the same purpose. This work experimental findings and the adaptation of the mechanical model to T-shaped beams lay the groundwork for a future development of a shear design and assessment formulation for concrete composite elements., The authors would like to thank the Ministerio de Ciencia e Innovación (MCIN) and the Agencia Estatal de Investigación (AEI) for their support through grants BIA2015-64672-C4-4-R and RTI2018-099091-B-C21-AR, both funded by MCIN/AEI/ 10.13039/ 501100011033 and by ¿ERDF A way of making Europe¿. Author Lisbel Rueda-García was supported through grant BES-2016-078010 funded by MCIN/AEI/ 10.13039/501100011033 and by ¿ESF Investing in your future¿. The Regional Government of Valencia also supported this research through Project AICO/2018/250. This research work was undertaken at the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politècnica de València (UPV; Spain) with concrete supplied by Caplansa.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Feasibility of iron-based shape memory alloy strips for shear strengthening of damaged RC beams promoting the formation of plastic hinges

  • Traver-Abella, Celia
  • Ruiz Pinilla, Joaquín Guillermo
  • Monserrat-Lopez, Andrea
  • Montoya-Coronado, Luis A.
  • Ribas, Carlos
  • Cladera, Antoni
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Bonet Senach, José Luís|||0000-0002-6687-5307
[EN] This research focuses on the proof of concept of the feasibility of iron-based shape memory alloys strips (Fe-SMA) to strengthen damaged structures by promoting the yielding of longitudinal reinforcement. For this purpose, an experimental campaign on real-scale reinforced concrete beams previously damaged on shear and retested after being strengthened was carried out. The strengthening technique consists of external Fe-SMA strips wrapping the beams. The results show a very significant increase in both shear strength and ductility. In addition, shear predictions were calculated and compared by several design models. This study highlights the potentialities of Fe-SMA as a strengthening technique for damaged beams on shear., The authors would like to thank the financial support provided by Grants: PID2021-126397OB-I00, PID2021-123701OB-C22, BIA2015-64672-C4-4-R and BIA2015-3 64672-C4-3-R by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe."; RTI2018-099091-B-C21-AR and RTI2018-099091-B-C22 by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe" and BIA2015-64672-C4-4-R and BIA2015-64672-C4-3-R (AEI/FEDER, UE); and TED2021-129358B-I00 and TED2021-130272B-C22 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGeneration EU/PRTR". The Regional Valencian Government also supported this research with Project AICO/2020/295. Andrea Monserrat is supported by the Ministry of Universities (Spain) with the Recovery, Transformation and Resilience Plan (RD 289/2021 and order UNI/551/2021) funded by NextGenerationEU. The authors thank the Spanish Ministry of Science and Innovation for Grant FPU18/03310 that supported Celia Traver Abella. This research work was undertaken at the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politecnica de Valencia (UPV; Spain), with concrete supplied by Caplansa. They also appreciate the contribution of the re-fer AG Strengthening Solution Company, which provided the memory steel (Fe-SMA strips).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Influence of Flexural Reinforcement Yielding on the Shear Strength of Reinforced Concrete Beams with and without Shear Reinforcement

  • López, Andrea Montserrat
  • Miguel Sosa, Pedro Francisco
[EN] Statically indeterminate structures such as continuous beams allow redistribution of internal forces. For increasing loads after yielding of the flexural reinforcement, shear forces and flexural deformations may increase, making it possible to reach shear failures even after the full flexural capacity of the structure is developed. An extensive experimental programme consisting of 30 shear tests (15 cantilever tests and 15 continuous beam tests) was carried out to assess the shear strength of reinforced concrete beams with and without shear reinforcement. Some of the tests were designed to fail in shear after yielding of the flexural reinforcement. The main objective of this experimental study was analysing the influence of large flexural strains on shear strength. The tests were instrumented by means of surface measurements using Digital Image Correlation (DIC). These measurements allowed controlling the evolution of strains at concrete surface to obtain the rotation of the plastic hinges and tracking the development and kinematics of the critical shear crack to obtain, by accounting for suitable constitutive models, the contribution of the various shear-transfer actions. The analysis of the test results confirmed the reduction of shear strength provided by concrete with increasing flexural rotation both in tests with and without shear reinforcement. Moreover, this shear strength component weakened for increasing shear reinforcement ratios. The test results were compared with the shear strength values predicted by different design codes, showing that these formulations did not properly capture the loss of shear strength caused by plastic deformation. The proposed simplified method to calculate the shear strength of the plastic hinges accounting for the plastic rotation demand shows consistent agreement for the experimental results., [ES] Las estructuras hiperestáticas, tales como las vigas continuas, permiten la redistribución de esfuerzos internos, de forma que, tras la plastificación de la armadura de flexión, el esfuerzo cortante y la deformación pueden aumentar con el incremento de las cargas aplicadas, siendo posible alcanzar roturas por cortante incluso después de agotar la capacidad resistente por flexión de la estructura. En este artículo se presenta un extenso programa experimental constituido por 30 ensayos de cortante (15 ensayos de voladizo y 15 ensayos de vigas continuas) llevado a cabo para evaluar la resistencia a cortante de vigas de hormigón armado con y sin armadura de cortante, algunas de ellas diseñadas para fallar a cortante tras la plastificación de la armadura de flexión. El principal objetivo de este estudio experimental era analizar la influencia del desarrollo de grandes deformaciones de flexión en la resistencia a cortante. Durante los ensayos, se empleó la Correlación Digital de Imágenes (DIC) para obtener medidas de deformación superficiales. Estas medidas permitieron analizar la evolución de las deformaciones en la superficie de hormigón para obtener la rotación de las rótulas plásticas y hacer un seguimiento del desarrollo y la cinemática de la fisura crítica de cortante con el objetivo de obtener, considerando los modelos constitutivos adecuados, la contribución a la resistencia de los distintos mecanismos de transferencia de cortante. El análisis de los resultados confirmó la reducción de la componente de la resistencia a cortante proporcionada por el hormigón con el aumento de la rotación de flexión, tanto en los especímenes con armadura de cortante como sin ella. Además, esta componente de la resistencia a cortante resultó menor cuanto mayor era cuantía de armadura de cortante. Los resultados se compararon con los valores de resistencia propuestos por distintos códigos de diseño, mostrando que estas formulaciones no capturan adecuadamente la reducción de resistencia a cortante causada por la deformación plástica. El método simplificado que se propone para el cálculo de la resistencia a cortante de las rótulas plásticas considerando la demanda de rotación plástica predice resultados coherentes respecto a los obtenidos experimentalmente., This research was funded with grants from the Ministerio de Economia y Competitividad (Spain) with Research Project BIA2015-64672-C4-4-R. Andrea Monserrat was particularly supported by the Conselleria d'Educacio, Investigacio, Cultura i Esport of the Generalitat Valenciana (Order 6/2015, DOCV no. 7615 15.09.2015) funded with European Regional Development Funds (ERDF) as a predoctoral researcher and by the Ministerio de Universidades (Spain) with the Recovery, Transformation and Resilience Plan (RD 289/2021 and order UNI/551/2021) funded by NextGenerationEU as a postdoctoral researcher.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Towards the Development of a Formulation for Obtaining the Shear Strength of Concrete Composite Beams, Hacia el desarrollo de una formulación para la obtención de la resistencia a cortante de vigas compuestas de hormigón

  • Rueda-García, Lisbel|||0000-0002-2061-1656
  • Bonet Senach, José Luís|||0000-0002-6687-5307
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Fernández Prada, Miguel Ángel|||0000-0001-5527-7793
[EN] In the design and assessment of precast concrete beams with a slab cast on top, namely concrete composite beams, engineers still face in practice unsolved shear-related issues, such as the contribution to shear strength of the slab, the concrete strength to be considered in shear formulations or the influence of the interface between concretes in the shear behaviour. In the present research, 69 shear tests were performed on monolithic and composite beams, with rectangular or T-shaped cross-section, with or without transverse reinforcement and with different concrete qualities, to experimentally analyse the issues mentioned above. The study of the shear transfer mechanisms at failure led to formulating a model for explaining the observed results. Based on this model, a shear strength predictive formulation for concrete composite beams with web reinforcement has been developed, which has been verified with the experimental results from this research and 24 additional tests from the literature. This formulation provides accurate predictions compared to the shear strength formulations of current codes EC2, MC-10 and ACI 318-19. The proposed model lays the foundations for the future development of a user-friendly formulation for calculating the shear strength of concrete composite beams., [ES] En el diseño y evaluación de vigas prefabricadas de hormigón con una losa superior hormigonada in situ, es decir, vigas compuestas de hormigón, los ingenieros siguen enfrentándose en la práctica a problemas no resueltos relacionados con el cortante, como la contribución de la losa a la resistencia a cortante, la resistencia del hormigón que se ha de considerar en las formulaciones de cortante o la influencia de la interfaz entre hormigones en el comportamiento a cortante. En la presente investigación se han realizado 69 ensayos a cortante en vigas monolíticas y compuestas, de sección rectangular o en T, con o sin armadura transversal y con diferentes calidades de los hormigones, para analizar experimentalmente las cuestiones mencionadas anteriormente. El estudio de los mecanismos de transferencia de cortante condujo a la formulación de un modelo para explicar los resultados observados. A partir de este modelo, se ha desarrollado una formulación para predecir la resistencia a cortante en vigas compuestas de hormigón con armadura de cortante, la cual se ha verificado con los resultados experimentales de esta investigación y 24 ensayos adicionales de la literatura. Esta formulación proporciona resultados precisos comparados con las formulaciones de resistencia a cortante de los códigos actuales EC2, MC-10 y ACI 318-19. El modelo propuesto sienta las bases para el futuro desarrollo de una formulación fácil de usar para el cálculo de la resistencia a cortante de vigas compuestas de hormigón., Ministerio de Ciencia e Innovación (MCIN) and Agencia Estatal de Investigación (AEI) supported the present research work through grants BIA2015-64672-C4-4-R and RTI2018-099091-B-C21-AR, both funded by MCIN/ AEI/ 10.13039/501100011033 and by ERDF A way of making Europe . Author Lisbel Rueda-García was supported by grant BES-2016-078010 funded by MCIN/AEI/ 10.13039/501100011033 and by ESF Investing in your future . The project was also carried out with the support of the Regional Government of Valencia through Project AICO/2018/250. This research work was undertaken at the Concrete Science and Technology University Institute (ICITECH) of the Universitat Politècnica de València (UPV; Spain) with concrete supplied by Caplansa.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Strength of pile caps under eccentric loads: Experimental study and review of code provisions

  • Miguel-Tortola, Lucia
  • Miguel Sosa, Pedro|||0000-0001-5395-8149
  • Pallarés Rubio, Luis|||0000-0003-2126-2387
[EN] Pile caps are rigid reinforced concrete structures that transfer column loads, generally consisting of a combination of an axial load and bending moments in one or two directions, to the piles. The design formulations of pile caps for more than two piles were derived from the results of experimental tests under a centered load. The practice of checking both punching and shear failure modes is common as described in the literature review, even though these formulations were developed for more slender elements. Currently, Codes ACI 318-14 and EC2 allow designing pile caps with strut-and-tie models or sectional approaches (shear, punching and flexural designs). In this study, 21 full-scale pile caps with different shear span-depth ratios and reinforcement layouts were studied to investigate the effect of eccentric loading on the strength and accuracy of the code formulations. The results show that in eccentrically loaded pile caps, the ultimate load is reduced but the maximum pile reaction increases and the secondary reinforcement proves effective to enhance the pile cap strength. Although the strut-and-tie models (STM) allow eccentric loads to be taken into consideration, they predict a much lower peak load than that observed at the experimental results and do not adequately reflect either the influence of slenderness or the failure mode. In general the sectional approach provided by Codes ACI-318-14, EC2 and MC-2010 (Level I of Approximation) lead to safe predictions of the peak load but do not always correctly predict the failure mode. The ultimate load predicted by EC-2 formulation comes closest to the experimental peak load, accurately reflects the influence of slenderness and the effect of secondary reinforcement, however, additional assumptions need to be made for its application. The ACI formulation complemented by the CRSI-2008 Special Investigation for deep pile caps is the safest but does not adequately capture the effect of horizontal and vertical secondary reinforcement. The MC2010 LoAI formulation is also conservative but does not detect the influence of slenderness or the contribution of secondary reinforcement., The authors wish to express their gratitude for the financial support (BIA2012-32300 and BIA2015-64672-C4-4-R) received from the Spanish Ministry of Economy and Competitiveness, which enabled the experimental campaign to be carried out, also for the PhD fellowship (BES-2013-063409).
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Estudio experimental del efecto tamaño en la resistencia a cortante de elementos de hormigón

  • Varela-Puga, Fernando
  • Herrador, Manuel
  • Martínez-Abella, Fernando
  • Paredes González, Manuel
  • Eiras López, Javier
[Resumen]: El comportamiento de elementos de hormigón a cortante es y ha sido en la última época un tema de constante debate en el área de la ingeniería estructural. Existe gran distancia entre la realidad del fenómeno y la interpretación de las normativas, que suelen proporcionar expresiones semi-empíricas con ajustes basados en análisis estadísticos. Dentro de este paradigma, asociado principalmente a elementos de hormigón armado, la reducción de la tensión tangencial media resistida a medida que aumenta su dimensión representativa, fenómeno conocido como efecto tamaño, se alza como uno de los aspectos a los que es necesario aportar más información empírica. Sin embargo, la experimentación en este campo es reducida debido a la dificultad de este tipo de ensayos en escalas representativas. Es en este punto donde se han centrado los esfuerzos de esta investigación, intentando identificar y cuantificar los mecanismos resistentes que aparecen en un elemento sometido a grandes solicitaciones tangenciales. Para ello, se ha realizado una campaña experimental sobre vigas de gran canto: 1.00 m (serie S), 1.50 m (serie M) y 2.00 m (serie L) de canto con longitud suficiente no incurrir en un efecto arco y, así mismo, poder realizar un ensayo a cortante sobre cada vano. Durante los ensayos se ha monitorizado y medido de manera directa (extensometría clásica) e indirecta (videocorrelación) los posibles mecanismos resistentes analizados en la bibliografía relativa: cabeza de compresión, armadura, armadura longitudinal y transmisión de tensiones en la fisura principal. El presente documento expone los resultados de la campaña experimental descrita. Además se realiza un estudio de la situación existente a día de hoy de la relación entre la realidad de la capacidad resistente a cortante de elementos de grandes dimensiones y las interpretaciones realizadas por las normativas vigentes., [Abstract]: The behaviour of concrete elements subjected to shear stress is and has been in recent time subject of constant discussion on structural engineer area. There is a great distance between the reality of the phenomenon and the standards interpretation, which tend to propose semi-empiric expressions with adjustments based on statistical analysis. Within this paradigm, mainly associated with reinforced concrete elements, the reduction of the average shear stress capacity as their characteristic dimension increases— known as the size effect—emerges as one of the aspects that requires further empirical evidence. However, experimental research in this field is limited due to the difficulty of conducting tests at representative scales. It is at this point where the efforts of the present research have been focused, aiming to identify and quantify the resisting mechanisms that develop in an element subjected to high shear demands. To this end, an experimental campaign was carried out on deep beams with depths of 1.00 m (Series S), 1.50 m (Series M), and 2.00 m (Series L), with sufficient span length to avoid arching effects and to allow for shear testing in each span. During the tests, the possible resisting mechanisms discussed in the literature were monitored and measured both directly (using conventional strain gauges) and indirectly (through digital image correlation), including the compression strut, transverse reinforcement, longitudinal reinforcement, and stress transfer across the main crack. This document presents the results of the described experimental campaign. In addition, it includes an analysis of the current state of the relationship between the actual shear capacity of large-scale elements and the interpretations provided by existing design codes., Los autores de este documento agradecen a las universidades de A Coruña (UDC), Universidad Politécnica de Cataluña (UPC), Illes Balears (UIB) y Universidad Politécnica de Valencia (UPV), sedes de los grupos de investigación que han realizado este estudio y los medios experimentales que han puesto a su disposición. La investigación ha sido posible gracias al proyecto coordinado HORVITAL (Referencias: BIA2015-64672-C4-4-R; BIA2015-64672-C4-3-R), financiado por el Ministerio de Economía, Industria y Competencia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

The influence of flexural reinforcement yielding on the shear strength of reinforced concrete beams with and without shear reinforcement, Influencia de la plastificación del armado a flexión en la resistencia a cortante de las vigas de hormigón armado con y sin armadura de cortante

  • Monserrat López, Andrea
  • Miguel Sosa, Pedro
Las estructuras hiperestáticas, tales como las vigas continuas, permiten la redistribución de esfuerzos internos, de forma que, tras la plastificación de la armadura de flexión, el esfuerzo cortante y la deformación pueden aumentar con el incremento de las cargas aplicadas, siendo posible alcanzar roturas por cortante incluso después de agotar la capacidad resistente por flexión de la estructura. En este artículo se presenta un extenso programa experimental constituido por 30 ensayos de cortante (15 ensayos de voladizo y 15 ensayos de vigas continuas) llevado a cabo para evaluar la resistencia a cortante de vigas de hormigón armado con y sin armadura de cortante, algunas de ellas diseñadas para fallar a cortante tras la plastificación de la armadura de flexión. El principal objetivo de este estudio experimental era analizar la influencia del desarrollo de grandes deformaciones de flexión en la resistencia a cortante. Durante los ensayos, se empleó la Correlación Digital de Imágenes (DIC) para obtener medidas de deformación superficiales. Estas medidas permitieron analizar la evolución de las deformaciones en la superficie de hormigón para obtener la rotación de las rótulas plásticas y hacer un seguimiento del desarrollo y la cinemática de la fisura crítica de cortante con el objetivo de obtener, considerando los modelos constitutivos adecuados, la contribución a la resistencia de los distintos mecanismos de transferencia de cortante. El análisis de los resultados confirmó la reducción de la componente de la resistencia a cortante proporcionada por el hormigón con el aumento de la rotación de flexión, tanto en los especímenes con armadura de cortante como sin ella. Además, esta componente de la resistencia a cortante resultó menor cuanto mayor era cuantía de armadura de cortante. Los resultados se compararon con los valores de resistencia propuestos por distintos códigos de diseño, mostrando que estas formulaciones no capturan adecuadamente la reducción de resistencia a cortante causada por la deformación plástica. El método simplificado que se propone para el cálculo de la resistencia a cortante de las rótulas plásticas considerando la demanda de rotación plástica predice resultados coherentes respecto a los obtenidos experimentalmente., This research was funded with grants from the Ministerio de Economía y Competitividad (Spain) with Research Project BIA2015-64672-C4-4-R. Andrea Monserrat was particularly supported by the Conselleria d’Educació, Investigació, Cultura i Esport of the Generalitat Valenciana (Order 6/2015, DOCV no. 7615 15.09.2015) funded with European Regional Development Funds (ERDF) as a pre-doctoral researcher and by the Ministerio de Universidades (Spain) with the Recovery, Transformation and Resilience Plan (RD 289/2021 and order UNI/551/2021) funded by NextGenerationEU as a post-doctoral researcher. The experimental programme was developed in the Laboratory of Concrete of the Institute of Concrete Science and Technology (ICITECH) of the Universitat Politècnica de València (UPV). VIC2D software was employed during the research stay of Andrea Monserrat at the EPFL (Lausanne, Switzerland)., Peer Reviewed, Postprint (published version)