Pasar al contenido principal

DESARROLLO Y APLICACION DE ENSAYOS NO DESTRUCTIVOS BASADOS EN ONDAS MECANICAS PARA LA EVALUACION Y MONITORIZACION DE REOLOGIA Y AUTOSANACION EN MATERIALES CEMENTANTES

BIA2017-87573-C2-2-P

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Nonlinear Acoustic Spectroscopy and Frequency Sweep Ultrasonics: Case on Thermal Damage Assessment in Mortar

  • Genovés, V.
  • Escobar, D.
  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] An exhaustive study on thermal damage of Portland cement-based materials is addressed. Damage carried out at different temperatures on concrete between 40 and 525 degrees C were assessed by means of microstructural, physical and nondestructive tests. Microstructural analysis (thermogravimetry and scanning electron microscopy) showed the principal changes of the Portland cement hydrated products for the different analysed temperatures. Compressive and flexural strengths remained constant or even increased at a low heating temperature range, while the mass loss increases. Dilatometry analysis revealed important information about deformation incompatibilities between the paste and the aggregate. These results have been correlated with nondestructive tests: nonlinear impact resonance acoustic spectroscopy (NIRAS) and ultrasonic measures. The dynamic modulus and ultrasonic pulse velocity have closely predicted the linear stiffness decay of the specimens. However, hysteretic parameter from NIRAS analysis exhibited a different trend from stiffness-related parameters, keeping constant until 250>degrees C and suffering a huge increasing for 400 and 525 degrees C. Ultrasonic attenuation computed with a broadband ultrasonic signal (chirp) revealed interesting information about scattering components inside the material, and is sensitive to interfacial transition zone between aggregate and paste in a large range of frequencies. The correlation between microstructural, mechanical and nondestructive techniques were carried out successfully. Nonlinear vibration and ultrasonic attenuation are non-conventional parameters that gave specific information about a complex damage process, such as a thermal attack in highly heterogeneous materials (e.g. Portland cement composites)., This work has been supported by the Spanish Administration under Grants, BES2015-071469, under the ONDATEST coordinated project, BIA2014-55311-C2-1-P and BIA2014-55311-C2-2-P. Thanks are given to FEDER funds for co-funding.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Joint Interference and Phase Alignment among Data Streams in Multicell MIMO Broadcasting

  • Shahjehan, Waleed
  • Shah, Syed Waqar
  • Lloret, Jaime|||0000-0002-0862-0533
  • Bosch Roig, Ignacio|||0000-0003-3190-3635
[EN] For the problem of channel state information (CSI) delay and error, this paper proposes a joint interference and phase alignment algorithm based on Bayesian estimation and power allocation among data streams for multicell, multiple-input multiple-output broadcast channels (MIMO-BC). Firstly, the sender obtains the best estimate of the current CSI through Bayesian estimation. Secondly, the interference suppression matrix is designed by maximizing the ratio of the desired signal power to the intercell interference plus noise ratio (SINR) in the forward link, and in the reverse communication, by maximizing the SINR design precoding. Further, the water-filling algorithm is combined to optimize power allocation among data streams. Finally, the phase alignment is used to rotate the interference between data streams into the signal space of the target receive data stream, thereby enhancing the received power of the target data stream. Simulation results show that the proposed algorithm has certain performance advantages over other algorithms, whether it is ideal CSI or delay and error CSI., This work has been partially supported by the "Ministerio de Economia y Competitividad" in the "Programa Estatal de Fomento de la Investigacion Cientifica y Tecnica de Excelencia, Subprograma Estatal de Generacion de Conocimiento" within the project under Grant BIA2017-87573-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of slow dynamics and conditioning on non-linear hysteretic material evaluation using impact resonance acoustic spectroscopy

  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • Genovés, V.
  • Perez, G.
  • Bittner, J.
  • POPOVICS, J.S.
[EN] The microstructural features of heterogeneous and porous materials give rise to unique non-linear dynamic behaviour. The purpose of this work is to investigate the dynamic response of thermally damaged concrete specimens measured by two different techniques: Non-linear Impact Resonance Acoustic Spectroscopy (NIRAS) and new Flipped Accumulative Non-linear Single Impact Acoustic Spectroscopy (FANSIRAS). Specimens were characterised in two different dynamic condition states of the material: relaxed and conditioned. The specimen¿s relaxed state indicates that no previous dynamic excitation event ocurred. The conditioned state denotes that the specimen has been dynamically tested before. The NIRAS results show that the non-linear material parameters, af and aQ , are affected by their previous dynamic history (its conditioning). The recently proposed algorithm, FANSIRAS, extracts from a single resonant signal equivalent results to NIRAS when the specimen is conditioned. In this situation, both parameters af and aQ were equivalent. The results suggest that new NDT parameters based on non-linear hysteretic parameters can quantify the damage level of thermally treated mortar specimens., This work has been supported by the Spanish Administration under grants BIA2014-55311-C2, BIA2017-87573-C2, BES2015-071469, PAID-10-19 and FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Joint Approach for Low-Complexity Channel Estimation in 5G Massive MIMO Systems

  • Bangash, kifayatullah
  • Khan, Imran
  • Lloret, Jaime|||0000-0002-0862-0533
  • León Fernández, Antonio|||0000-0002-9374-9277
[EN] Traditional Minimum Mean Square Error (MMSE) detection is widely used in wireless communications, however, it introduces matrix inversion and has a higher computational complexity. For massive Multiple-input Multiple-output (MIMO) systems, this detection complexity is very high due to its huge channel matrix dimension. Therefore, low-complexity detection technology has become a hot topic in the industry. Aiming at the problem of high computational complexity of the massive MIMO channel estimation, this paper presents a low-complexity algorithm for efficient channel estimation. The proposed algorithm is based on joint Singular Value Decomposition (SVD) and Iterative Least Square with Projection (SVD-ILSP) which overcomes the drawback of finite sample data assumption of the covariance matrix in the existing SVD-based semi-blind channel estimation scheme. Simulation results show that the proposed scheme can effectively reduce the deviation, improve the channel estimation accuracy, mitigate the impact of pilot contamination and obtain accurate CSI with low overhead and computational complexity., This research was funded by Ministerio de Economia, Industria y Competitividad, Gobierno de Espana grant number BIA2017-87573-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comparative Study of Coupling Techniques in Lamb Wave Testing of Metallic and Cementitious Plates

  • Vazquez-Martinez, Santiago
  • Gallardo-Llopis, Carles
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • Bosch Roig, Ignacio|||0000-0003-3190-3635
  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[Otros] Lamb waves have emerged as a valuable tool to examine long plate-like structures in a faster way compared to conventional bulk wave techniques, which make them attractive in non-destructive testing. However, they present a multimodal and dispersive nature, which hinders signal identification. Oblique incidence is one of the most known methods to generate and receive Lamb waves and it is applied in different experimental arrangements with different types of sensors. In this work, several setups were conducted and compared to determine the optimal ones to launch and detect ultrasonic Lamb waves, especially in non-homogeneous specimens. The chosen arrangements were contact with angle beam transducers, immersion in a water tank, localised water coupling using conical containers and air coupling. Plates of two different materials were used, stainless steel and Portland cement mortar. Theoretical and experimental dispersion curves were compared to verify the existence of Lamb modes and good correspondence was achieved., This research was funded by the Spanish Administration, grants number BES-2015-071958 and BIA2017-87573-C2.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An Efficient Approach for Coordination of Dual-Channel Closed-Loop Supply Chain Management

  • Arshad, Muhammad
  • Khalid, Qazi Salam
  • Lloret, Jaime|||0000-0002-0862-0533
  • León Fernández, Antonio|||0000-0002-9374-9277
[EN] In this paper, a closed-loop supply chain composed of dual-channel retailers and manufacturers, a dynamic game model under the direct recovery, and an entrusted third-party recycling mode of the manufacturer is constructed. The impact of horizontal fairness concern behavior is introduced on the pricing strategies and utility of decision makers under different recycling models. The equilibrium strategy at fair neutrality is used as a reference to compare offline retails sales. Research shows that in the closed-loop supply chain of dual-channel sales, whether in the case of fair neutrality or horizontal fairness concerns, the manufacturer's direct recycling model is superior to the entrusted third-party recycling, and the third-party recycling model is transferred by the manufacturer. In the direct recycling model, the horizontal fairness concern of offline retailers makes two retailers in the positive supply chain compete to lower the retail price in order to increase market share. Manufacturers will lower the wholesale price to encourage competition, and the price will be the horizontal fairness concern coefficient, which is negatively correlated. In the reverse supply chain, manufacturers increase the recycling rate of used products. This pricing strategy increases the utility of manufacturers and the entire supply chain system compared to fair neutral conditions, while two retailers receive diminished returns. Manufacturers, as channel managers to encourage retailers to compete for price cuts, can be coordinated through a three-way revenue sharing contract to achieve Pareto optimality., This research was funded by Ministerio de Economia, Industria y Competitividad, Gobierno de Espana grant number BIA2017-87573-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Novel Multi-User Codebook Design for 5G in 3D-MIMO Heterogeneous Networks

  • Arshad, Muhammad
  • Khan, Imran
  • Lloret, Jaime|||0000-0002-0862-0533
  • Bosch Roig, Ignacio|||0000-0003-3190-3635
[EN] The 2D precoding technology can only adjust the beam in a horizontal direction through data processing, which will cause serious problems for multiuser systems, especially at the edge of the base station it will cause serious inter-cell interference. To solve this problem, in the frequency-division duplex (FDD) 3D-MIMO Heterogeneous network system, the influence of feedback overhead on system performance under limited feedback mechanism is studied using random geometry. Based on the deployment of a uniform planar array (UPA) at the base station, a 3D-MIMO multiuser codebook design scheme based on horizontal transmission angle and the vertical down-tilt angle is proposed, and the codebook design scheme is simulated and analyzed. The results show that the feedback overhead and the micro base station density affect the system throughput and even affect the bit error rate (BER) of the 3D precoding scheme. Compared with the precoding scheme based on 2D and 3D discrete Fourier transform (DFT) codebooks, this scheme greatly reduces the system¿s BER, improves the system¿s throughput, and optimizes system performance., This work has been partially supported by the "Ministerio de Economia y Competitividad" in the "Programa Estatal de Fomento de la Investigacion Cientifica y Tecnica de Excelencia, Subprograma Estatal de Generacion de Conocimiento" within the project under Grant BIA2017-87573-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Nuevas técnicas de ensayos no destructivos basadas en ondas mecánicas para la valoración del daño en materiales cementicios

  • Vázquez Martínez, Santiago
[ES] En la actualidad, una gran cantidad de infraestructuras están compuestas de forma parcial o total de materiales cementicios, siendo el hormigón uno de los materiales cementicios más antiguos y utilizados en la construcción debido a su bajo coste, durabilidad y características mecánicas y estructurales. Pese a sus características, estos materiales están expuestos a diversas condiciones adversas del entorno y sufren procesos de deterioro que afectan a su integridad y seguridad. El reconocimiento de la integridad y seguridad en las estructuras cementicias ha implicado una extensa investigación y el desarrollo de diversas pruebas para verificar su calidad y estado. Mediante la destrucción de una muestra extraída de la estructura, en el caso de los ensayos destructivos (ED), o mediante la inspección de la estructura sin necesidad de dañarla o alterar sus propiedades, en el caso de los ensayos no destructivos (END). Existen multitud de técnicas END que tratan de caracterizar estas estructuras sin dañarlas, siendo la inspección mediante ultrasonidos una de las más utilizadas en materiales cementicios. Tradicionalmente estas técnicas ultrasónicas se basan en el estudio de las ondas longitudinales (P) y transversales (S), que permiten caracterizar una estructura mediante la realización de múltiples medidas. Sin embargo, existe otro tipo de ondas, formadas por la superposición de los desplazamientos de las partículas de las ondas P y S denominadas ondas guiadas, las cuales permiten inspeccionar una estructura de forma global a partir de una única medida, además de ser capaces de propagarse a grandes distancias manteniendo una buena relación señal-a-ruido en comparación a las ondas P y S. Dentro de las ondas guiadas más utilizadas para inspeccionar materiales cementicios, se encuentran las ondas de Rayleigh y las ondas de Lamb. Las ondas de Rayleigh se propagan en estructuras de gran espesor, mientras que las ondas de Lamb se propagan en placas. Las ondas de Lamb presentan una naturaleza dispersiva y multimodal. Su naturaleza dispersiva implica que las velocidades de fase y grupo de estas ondas depende de la frecuencia, mientras que la naturaleza multimodal implica que existen cada vez más modos de propagación conforme aumenta la frecuencia de excitación. Se pueden excitar y detectar selectivamente los distintos modos de Lamb mediante la incidencia oblicua, es decir, variando la inclinación del transmisor y el receptor. Para ello, existen distintas técnicas de acoplamiento que permiten la incidencia oblicua, como el acoplamiento por cuñas sólidas, el acoplamiento por agua y el acoplamiento por aire. La presente tesis se ha centrado en el estudio de nuevas técnicas de END basadas en ondas guiadas para caracterizar diferentes tipos de daño en los materiales cementicios. Para ello, se han llevado a cabo un número considerable de medidas experimentales basadas en distintas técnicas de acoplamiento para la generación y captación de ondas guiadas. Inicialmente se han analizado materiales homogéneos como los metales, para, posteriormente, utilizar el conocimiento adquirido en dichos materiales y estudiar materiales más heterogéneos como los cementicios. Se han evaluado diferentes tipos de técnicas de acoplamiento junto con diferentes tipos de transductores. Los materiales cementicios se han inspeccionado mediante ondas guiadas ultrasónicas con dos tipos de daño: la carbonatación, estudiando el efecto con probetas de dos capas de mortero, y el envejecimiento de fibras en placas de cemento reforzado con fibra de vidrio (GRC). Se ha demostrado que las ondas guiadas son sensibles a estos daños, obteniendo resultados esperanzadores. Concretamente, las ondas de Rayleigh se han utilizado en el daño por carbonatación debido a su sensibilidad a capas superficiales de degradación, mientras que en el envejecimiento de fibras se han utilizado las ondas de Lamb, por su sensibilidad a defectos a lo largo, [CA] En l'actualitat, una gran quantitat d'infraestructures estan formades totalment o parcialment de materials cementants. El formigó és un dels materials cementants més antics i utilitzats en la construcció degut al seu preu, la seua durabilitat i les seues característiques mecàniques i estructurals. Malgrat la seua durabilitat i característiques, aquests materials estan exposats a diverses condicions adverses de l'entorn i pateixen processos de deterioració que afecten la seua integritat i seguretat. El reconeixement de la integritat i seguretat en les estructures cementants ha implicat una extensa investigació i el desenvolupament de diverses proves per a verificar la seua qualitat i estat. Mitjançant la destrucció d'una mostra de l'estructura en el cas dels assajos destructius, o mitjançant la inspecció de l'estructura sense danyar-la o alterar les seues propietats en el cas dels assajos no destructius. Existeixen multitud de tècniques d'inspecció no destructiva que tracten de caracteritzar aquestes estructures sense danyar-les. La inspecció mitjançant ultrasons és un dels assajos no destructius més utilitzats en materials cementants. Tradicionalment, aquestes tècniques ultrasòniques estan basades en l'estudi de les ones longitudinals (P) i transversals (S), que permeten caracteritzar una estructura mitjançant la realització de múltiples mesures en l'estructura. No obstant, existeixen altres tipus d'ones, formades per la superposició dels desplaçaments de les partícules de les ones P i S, denominades ones guiades, les quals permeten inspeccionar una estructura de manera global a partir d'una única mesura, a més de poder propagar-se a grans distàncies mantenint una bona relació senyal-soroll en comparació a les ones P i S. Dins de les ones guiades més utilitzades per a inspeccionar materials cementants, es troben les ones de Rayleigh i les ones de Lamb. Les ones de Rayleigh es propaguen en estructures de gran grossària, mentre que les ones de Lamb es propaguen en plaques. Les ones de Lamb presenten una naturalesa dispersiva i multimodal. La seua naturalesa dispersiva implica que les velocitats de fase i grup d'aquestes ones depenen de la freqüència, mentre que la naturalesa multimodal implica que apareguen més modes de propagació a l'augmentar la freqüència d'excitació. Es poden excitar i detectar selectivament els diferents modes de Lamb mitjançant la incidència obliqua, és a dir, variant la inclinació del transmissor i el receptor. Existeixen diferents tècniques d'acoblament que permeten la incidència obliqua, com l'acoblament per metacrilat, l'acoblament per aigua i l'acoblament per aire. Aquesta tesi s'ha enfocat en l'estudi de noves tècniques d'assajos no destructius basades en ones guiades (ones de Rayleigh i ones de Lamb) per a caracteritzar diferents tipus de dany en els materials cementants. S'han realitzat un nombre considerable de mesures experimentals basades en diferents tècniques d'acoblament per a la generació i captació d'ones guiades. Inicialment s'han analitzat materials homogenis com els metalls per a, posteriorment, utilitzar el coneixement adquirit en aquests materials i estudiar d'altres més heterogenis com els cementants. Concretament, s'han avaluat diferents tipus de tècniques d'acoblament i diferents tipus de transductors. Els materials cementants s'han inspeccionat mitjançant ones guiades ultrasòniques amb dos tipus de dany o degradació: la carbonatació, estudiant el seu efecte amb provetes de dues capes de morter, i l'envelliment de fibres en plaques de ciment reforçat amb fibra de vidre (GRC). S'ha demostrat que les ones guiades són sensibles a aquests danys, obtenint resultats esperançadors. Concretament, les ones de Rayleigh s'han utilitzat en el dany per carbonatació a causa de la seua sensibilitat a capes superficials de degradació, mentre que en l'envelliment de fibres s'han utilitzat les ones de Lamb, per la seua sensibilitat a defe, [EN] Nowadays, a large number of infrastructures are partially or wholly built with cementitious materials. Concrete is one of the oldest and most popular cementitious materials due to its low cost, durability and remarkable mechanical and structural characteristics. However, if these materials are exposed to different environments and harsh conditions, they suffer damaging processes that affect their integrity and safety. To verify their state and quality, extensive research has been conducted and several tests have been developed, such as destructive testing and non-destructive testing. Destructive testing (DT) requires a sample of the inspected structure while non-destructive testing (NDT) allows the inspection of the structure without altering its properties and without damaging it. There are several NDT techniques that characterize cementitious structures without harming them, such as ultrasonic testing, which is one of the most widely used. This technique is based on the study of longitudinal (P) and shear (S) waves, which enable the characterization of a structure by a point-by-point scan. However, there are another kind of waves, called guided waves, which are composed of the superposition of the P and S wave particle displacements. Unlike P and S waves, guided waves allow a global inspection of a structure from a single transducer position and they are able to propagate over long distances with a good signal-to-noise ratio. Rayleigh and Lamb waves are the most frequently used guided waves in NDT of cementitious materials. Rayleigh waves propagate in thick structures while Lamb waves propagate in plate-like structures. Lamb waves are dispersive (their phase and group velocities depend on frequency) and multimodal (as frequency increases, many propagation modes with different velocities exist in the received signal). Lamb wave modes can be selectively excited and detected by means of oblique incidence, i.e., by varying the inclination of the transmitting and receiving transducers. Different coupling techniques can be used to change the inclination of the transducers, such as the contact technique with angle beam wedge transducers, water coupling and air coupling. This thesis has been focused in the study of new NDT techniques based on guided waves (Rayleigh and Lamb waves) to characterize different types of damage of cementitious materials. For this goal, a significant number of experimental arrangements based on different coupling techniques have been carried out. Firstly, homogeneous materials as metals have been analized, because they are a reference in guided wave testing. After performing different experiments in metals, the acquired knowledge has been used to inspect heterogeneous materials as cementitious ones. Different coupling techniques (variable angle wedges, immersion testing, fixed angle wedges, ...) with different types of transducers (contact transducers, immersion transducers and air-coupled transducers) have been employed. Cementitious materials with two damaging processes have been inspected by means of guided waves: two-layered mortar specimens to study carbonation and glass-fibre reinforced cement (GRC) plates to study fiber ageing. This thesis demonstrates that guided waves are sensitive to these damaging processes and the obtained results are encouraging. Specifically, Rayleigh waves have been used to detect carbonation due to its sensitivity to surface layers, while Lamb waves have been used to detect fiber ageing due to its sensitivity to defects along the thickness of the GRC plates., La investigación realizadaen esta tesis se ha financiado con las siguientes ayudas y proyectos concedidos por el gobierno español: Ayudas para contratos predoctorales para la formación de doctores 2015 (BES-2015-071958); Nuevas aplicaciones de ensayos no destructivos basados en ondas mecánicas para la evaluación de la degradación en materiales cementantes (BIA2014-55311-C2-2-P); Desarrollo y aplicación de ensayos no destructivos basados en ondas mecánicas para la evaluación y monitorización de reología y autosanación en materiales cementantes (BIA2017-87573-C2)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Airborne ultrasounds for damaged cementitious characterization

  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Gallardo, C.
  • Vázquez, S.
  • Genovés, V.
[EN] The scope of this paper is to demonstrate the capability of airborne non-contact ultrasound (ANC-US) to assess thermal damage on normalized Portland cement mortar specimens. For this purpose, contact ultrasound (C-US) and ANC-US are compared. A normalized dosage mortar was carried out to obtain standardized mortar specimens of 4 x 4 x 16 cm. Then, they were measured by ANC-US and C-US. Afterwards, they were thermal damaged (400º C) and measured again. Ultrasound velocity and frequency attenuation were estimated. As expected, damaged samples show lower velocities and higher attenuations than sound samples. It is remarkable how the attenuation keeps constant for frequencies below 100 kHz and increases due to the sensitivity of higher frequencies to the size of thermal microcracking. Although ANC-US does not require any coupling media as C-US does, it requires additional calibration to compensate propagation through the air and material boundaries. Considering these terms, both techniques offer consistent results and the capability of ANC-US technique for damage characterization in cementitious systems is proved., The authors acknowledge the support from T. Gomez Álvarez-Arenas (Institute for Physical and Information Technologies ITEFI-CSIC) and Spanish Administration under grant BIA2017- 87573.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Novel Codeword Selection Scheme for MIMO-MAC Lower-Bound Maximization

  • Shahjehan, Waleed
  • Shah, Syed Waqar
  • Lloret, Jaime|||0000-0002-0862-0533
  • Bosch Roig, Ignacio|||0000-0003-3190-3635
[EN] Aiming at the limitations of the existing Limited Feedback Interference Alignment algorithms, this paper proposes a direct codeword selection scheme that maximizes the lower-bound of the user rate and reduces the sum rate loss by integrating the Bit Allocation algorithm. The target signal is decoded using the maximum signal to interference plus noise ratio (MAX-SINR) algorithm. Moreover, low complexity and global searching mechanisms are deployed to select the optimized codewords from the generated sets of codewords that approach the ideal precoder. Simulation results show that the proposed algorithm effectively improves the rate lower-bound of the system user as compared with the existing state-of-the-art algorithms., This research was funded by Ministerio de Economia, Industria y Competitividad, Gobierno de Espana grant number BIA2017-87573-C2-2-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Airborne ultrasonic technique to measure leaky Lamb waves with narrowband and low-frequency excitation

  • Vázquez, S.
  • Wright, W. M. D.
  • Gallardo, C.
  • Gosálbez Castillo, Jorge|||0000-0001-6520-9014
  • Bosch Roig, Ignacio|||0000-0003-3190-3635
  • CARRIÓN GARCÍA, ALICIA|||0000-0002-0630-6065
Air-coupled non-destructive testing has become very valuable because eliminates the use of liquid couplants and enables a contactless fast inspection of structures. Multimodal leaky Lamb waves can be excited and sensed with this technology in plate-like specimens varying the excitation frequency and the inclination of the transducers. To reduce undesired effects, as the existence of unwanted modes, narrowband and low-frequency excitation signals can be used. In this paper, the generation and detection of ultrasonic leaky Lamb waves in a metallic plate with capacitive air-coupled transducers have been performed. Theoretical and experimental data have been matched, showing good correlation., The authors acknowledge the support from University College Cork (Ireland), Universitat Politècnica de València and the Spanish Administration under grants BIA2017-87573 and Salvador Madariaga's Programme (PR2017-00658).