Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Microstructure and Heat Treatment on the Corrosion Resistance of Mg-1Zn Alloy Produced by Laser Powder Bed Fusion

  • Reyes-Riverol, R.
  • Triviño Peláez, Ángel
  • García-Galván, F. R.
  • Lieblich, Marcela
  • Jiménez, José Antonio
  • Fajardo, Santiago
This article belongs to the Section Corrosion and Protection., The corrosion behavior of an additively manufactured Mg-1Zn alloy was investigated in both the transverse and longitudinal directions relative to the build direction, in the as-built condition and after annealing at 350 °C for 24 h under high vacuum. Microstructural characterization using XRD and SEM revealed the presence of magnesium oxide (MgO) and the absence of intermetallic second-phase particles. Optical microscopy (OM) images and Electron Backscatter Diffraction (EBSD) maps showed a highly complex grain morphology with anomalous, anisotropic shapes and a heterogeneous grain size distribution. The microstructure includes grains with a pronounced columnar morphology aligned along the build direction and is therefore characterized by a strong crystallographic texture. Electrochemical techniques, including PDP and EIS, along with gravimetric H2 collection, concluded that the transverse plane exhibited greater corrosion resistance compared to the longitudinal plane. Additionally, an increase in cathodic kinetics was observed when comparing as-built with heat-treated samples., Financial support under the Project PID2021-126166OB-I00, funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” (European Union); the Grant CNS2023-144665. funded by MCIN/AEI/10.13039/501100011033; and by the “European Union NextGenerationEU/PRTR”. S.F. and R.R.-R. thank the CSIC for the financial support under the project PIE-20216AT01., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructure and electrochemical behavior of AZ91 Mg Alloy produced by laser powder bed fusion

  • Reyes-Riverol, R.
  • Callaghan, G.
  • García-Galván, F. R.
  • Triviño Pélaez, Ángel
  • Medina, Judit
  • Williams, G.
  • Jiménez, José Antonio
  • Fajardo, Santiago
The corrosion behavior of the laser powder bed fusion (LPBF) AZ91 magnesium alloy was investigated by comparing its longitudinal and transverse sections with the cast AZ91 alloy. Microstructural analysis revealed a fine, homogeneous Mg<inf>17</inf>Al<inf>12</inf> distribution in LPBF samples, contrasting with the network-like structure in the cast alloy. Electrochemical and hydrogen evolution tests demonstrated no significant anisotropy in LPBF sections, but they exhibited higher corrosion rates than the cast alloy. Potentiodynamic polarization and electrochemical impedance spectroscopy confirmed that the corrosion process was cathodically controlled by the Mg<inf>17</inf>Al<inf>12</inf> phase fraction. Scanning vibrating electrode technique further validated these findings, highlighting lower electrochemical activity in cast AZ91 alloy., SF acknowledges the financial support under the Project PID2021-126166OB-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” (European Union), and the Grant CNS2023-144665 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR.” SF and RRR thank the CSIC for the financial support under the project PIE-20216AT012., Peer reviewed