Pasar al contenido principal

RESISTENCIA A LA CORROSION DE NUEVAS ALEACIONES DE MAGNESIO OBTENIDAS MEDIANTE FABRICACION ADITIVA

PID2021-126166OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2021
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

New electrochemical method for the determination of the barrier properties of corrosion protective coatings

  • Trujillo, S.
  • Reyes-Riverol, R.
  • García-Galván, F. R.
  • Fajardo, Santiago
A novel electrochemical method evaluates the durability of corrosion protective coatings by measuring the galvanic current between a coated AZ31 Mg alloy and a Pt auxiliary electrode in a 2 M NaCl solution. In this work an organo-inorganic sol-gel film was used. The durability criterion, t, was selected as the time where the galvanic current reached 1 mA. Validated using EIS, the method showed 82 % accuracy. However, this difference was not deemed statistically significant. Under the conditions used in this study, results from the new method align with traditional EIS, establishing its viability as a simple and straightforward tool for assessing the barrier properties of corrosion protective coatings., SF acknowledges the financial support under the Grant RYC2019-027006-I funded by MCIN/AEI/10.13039/501100011033 and by ting in you“ESF Invesr future”, and the Project PID2021-126166OB-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” (European Union). SF and RRR thank the CSIC for the financial support under the project PIE-20216AT012. FRGG acknowledges financial support through the PID2019-104717RB-I00 project from the Spanish Ministry of Science and Innovation (MICI). V. Barranco and J.C. Galvan are acknowledged for their valuable comments during the preparation of this paper.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ball milling and annealing effect in structural and magnetic properties of copper ferrite by ceramic synthesis

  • Cobos, Miguel Ángel
  • Jiménez, José Antonio
  • Llorente, Irene
  • Presa, Patricia de la
  • Hernando, Antonio
This study aims to better understand the relationship between the microstructure and magnetic properties of copper ferrite, which is an inverse spinel that present a body-centered tetragonal structure associated with a remarkable Jahn–Teller (JT) effect. For this goal, a sample has been synthesized by the ceramic route from a stoichiometric mixture of high-purity CuO and FeO powders activated mechanically in a high-energy planetary ball mill. This sample was calcined in air furnace at 1000 ºC for 6 h. As synthetized sample with a cubic structure was divided into two parts and one of them was annealed at 650 ºC for 3 h and slowly cooled to room temperature to obtain a pure tetragonal spinel sample. Furthermore, these two samples were subjected to the same processes of severe plastic deformation by milling for up to 70 h and subsequent annealing at temperatures ranging between 300 and 600 ºC to obtain samples with a mixture of phases in different proportions. For the cubic one, there is no change in its structure due to milling, always remaining 100 % cubic, and the evolution in the saturation magnetization was related to the changes in the density of defects present. On the other hand, copper cations are always found in the octahedral sites of spinel with a tetragonal structure. The small decrease in the degree of inversion to 0.95 induced by milling in this sample is capable of breaking the JT distortion, giving rise to the appearance of a cubic phase. This work demonstrates how the structure, microstructure, defects like stacking faults and deformation twins, and degree of inversion of the different phases are related to changes in magnetic properties., This work was supported by the Ministerio de Ciencia e Innovacion de España (Grant IDs. PID2021-123112OB-C21, PDC2022-133039-I00, TED2021-129688B-C21, PID2021-126166OB-I00, PID2022-138332NB-C41).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exploring the viability of Mg-3Pb alloy as sacrificial anode for the cathodic protection of AZ31, AM60 and AZ91 Mg alloys

  • García-Corredera, M.
  • Reyes-Riverol, R.
  • García-Galván, F. R.
  • Jiménez, José Antonio
  • Fajardo, Santiago
The use of a custom Mg-3Pb alloy as a sacrificial anode for protecting AZ31, AM60, and AZ91 Mg alloys in 0.1 M NaCl solution was evaluated using surface characterization, mass loss, electrochemical measurements, and gravimetric H collection. The Mg-3Pb alloy exhibited consistently lower open circuit potential values than the protected alloys and demonstrated protection efficiencies over 95 %. No polarity reversal or cathodic activation was observed, despite increased anomalous H evolution. These findings confirm the effectiveness and viability of Mg-3Pb alloy as a sacrificial anode for the cathodic protection of AZ31, AM60, and AZ91 Mg alloys., SF acknowledges the financial support under the Project PID2021-126166OB-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” (European Union), and the Grant CNS2023-144665 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGener ationEU/PRTR”. SF and RRR thank the CSIC for the financial support under the project PIE-20216AT012., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Microstructure and Heat Treatment on the Corrosion Resistance of Mg-1Zn Alloy Produced by Laser Powder Bed Fusion

  • Reyes-Riverol, R.
  • Triviño Peláez, Ángel
  • García-Galván, F. R.
  • Lieblich, Marcela
  • Jiménez, José Antonio
  • Fajardo, Santiago
This article belongs to the Section Corrosion and Protection., The corrosion behavior of an additively manufactured Mg-1Zn alloy was investigated in both the transverse and longitudinal directions relative to the build direction, in the as-built condition and after annealing at 350 °C for 24 h under high vacuum. Microstructural characterization using XRD and SEM revealed the presence of magnesium oxide (MgO) and the absence of intermetallic second-phase particles. Optical microscopy (OM) images and Electron Backscatter Diffraction (EBSD) maps showed a highly complex grain morphology with anomalous, anisotropic shapes and a heterogeneous grain size distribution. The microstructure includes grains with a pronounced columnar morphology aligned along the build direction and is therefore characterized by a strong crystallographic texture. Electrochemical techniques, including PDP and EIS, along with gravimetric H2 collection, concluded that the transverse plane exhibited greater corrosion resistance compared to the longitudinal plane. Additionally, an increase in cathodic kinetics was observed when comparing as-built with heat-treated samples., Financial support under the Project PID2021-126166OB-I00, funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” (European Union); the Grant CNS2023-144665. funded by MCIN/AEI/10.13039/501100011033; and by the “European Union NextGenerationEU/PRTR”. S.F. and R.R.-R. thank the CSIC for the financial support under the project PIE-20216AT01., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructure and electrochemical behavior of AZ91 Mg Alloy produced by laser powder bed fusion

  • Reyes-Riverol, R.
  • Callaghan, G.
  • García-Galván, F. R.
  • Triviño Pélaez, Ángel
  • Medina, Judit
  • Williams, G.
  • Jiménez, José Antonio
  • Fajardo, Santiago
The corrosion behavior of the laser powder bed fusion (LPBF) AZ91 magnesium alloy was investigated by comparing its longitudinal and transverse sections with the cast AZ91 alloy. Microstructural analysis revealed a fine, homogeneous Mg<inf>17</inf>Al<inf>12</inf> distribution in LPBF samples, contrasting with the network-like structure in the cast alloy. Electrochemical and hydrogen evolution tests demonstrated no significant anisotropy in LPBF sections, but they exhibited higher corrosion rates than the cast alloy. Potentiodynamic polarization and electrochemical impedance spectroscopy confirmed that the corrosion process was cathodically controlled by the Mg<inf>17</inf>Al<inf>12</inf> phase fraction. Scanning vibrating electrode technique further validated these findings, highlighting lower electrochemical activity in cast AZ91 alloy., SF acknowledges the financial support under the Project PID2021-126166OB-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe” (European Union), and the Grant CNS2023-144665 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR.” SF and RRR thank the CSIC for the financial support under the project PIE-20216AT012., Peer reviewed