Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Selective growth of ZnO micro- and nano-structures on fs-laser processed metallic Zn substrates for large area applications

  • Ariza, Rocío
  • Urbieta, A.
  • Ferreiro, A.
  • Rabanal, M. E.
  • Fernández, P.
  • Solís Céspedes, Javier
9 pages, 7 figures, 4 tables, The synthesis of large area micro- and nano-structured ZnO surfaces has been successfully achieved through a two-step process. It involves the irradiation of Zn metal sheets with femtosecond laser pulses (350 fs at 1030 nm) at high repetition rates (100–500 kHz), and fast scanning speeds (cm/s). Subsequently, the irradiated sheets are thermally treated in an Argon flux at 380 °C, a temperature significantly lower than that typically required for growing micro- and nanostructures in ZnO. Fs-laser irradiation promotes the initial development of topography and the localized oxidation of the metal. This enables the further growth of micro- and nanostructures at preferential sites with good crystalline quality and luminescent properties. Analysis of the material at different processing steps shows that the initial laser-induced oxidation is crucial in defining ZnO growth mechanisms upon thermal treatment, and determining the final properties. We have tested the potential use of these structures as reusable photocalyst. The ease of catalyst recovery in photocatalysis experiments and the degree of degradation achieved may be considered as key performance indicators. Photocatalytic activity tests performed with a Rhodamine B solution showed degradation values up to 43 % over 90 min. The morphology of the samples remains unaltered after photocatalysis experiments., The authors are grateful to MCIN/AEI/10.13039/501100011033 for the financial support through grants PID2020–112770RB-C21, PID2019–106631GB-C43 and CPP2022–009910, UCM under project PR3/23–30813, and project S2018/NMT-4411. RA acknowledges the funding from a Marie Skłodowska-Curie Postdoctoral grant (No 101149132)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Carbochlorination Reduction Process of Waelz ZnO: Characterization of Resulting ZnO-Based Oxides

  • Alcaraz, Lorena
  • Sotillo, Belén
  • Fernández, Paloma
  • López Gómez, Félix Antonio
Zinc-based oxides are the main products obtained after the Waelz process, a metallurgical method used industrially for the treatment of electric arc furnaces. These oxides have certain impurities in their composition, which can be a disadvantage. Carbochlorination reduction reactions have proven to be useful in eliminating certain impurities (especially Pb) through thermal treatments. In this work, a method for purifying Waelz oxide through carbochlorination reduction reactions is presented. Several experiments have been conducted with the aim of obtaining samples with potential end applications. A deep characterization of the purified oxides has been performed by means of X-ray microanalysis, X-ray diffraction, Raman spectroscopy, and cathodoluminescence. These measurements indicate the presence of ZnO and ZnFe<sub>2</sub>O<sub>4</sub> in different proportions, depending on the different amounts of reducing and chlorinating agents used., The authors are grateful to the Comunidad de Madrid for support via the Project PR65/19-22464 (Proyectos de I+D para jóvenes doctores) and to the project CPP2022-009910 financed by MCIN/AEI/10.13039/501100011033 and by NextGeneration EU/PRTR., Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

Selective growth of ZnO micro- and nano-structures on fs-laser processed metallic Zn substrates for large area applications

  • Ariza, R.
  • Urbieta Quiroga, Ana Irene
  • Ferreiro, A.
  • Rabanal, M.E.
  • Fernández Sánchez, Paloma
  • Solis, J.
The synthesis of large area micro- and nano-structured ZnO surfaces has been successfully achieved through a two-step process. It involves the irradiation of Zn metal sheets with femtosecond laser pulses (350 fs at 1030 nm) at high repetition rates (100–500 kHz), and fast scanning speeds (cm/s). Subsequently, the irradiated sheets are thermally treated in an Argon flux at 380 ◦C, a temperature significantly lower than that typically required for growing micro- and nanostructures in ZnO. Fs-laser irradiation promotes the initial development of topography and the localized oxidation of the metal. This enables the further growth of micro- and nanostructures at preferential sites with good crystalline quality and luminescent properties. Analysis of the material at different processing steps shows that the initial laser-induced oxidation is crucial in defining ZnO growth mechanisms upon thermal treatment, and determining the final properties. We have tested the potential use of these structures as reusable photocalyst. The ease of catalyst recovery in photocatalysis experiments and the degree of degradation achieved may be considered as key performance indicators. Photocatalytic activity tests performed with a Rhodamine B solution showed degradation values up to 43 % over 90 min. The morphology of the simples remains unaltered after photocatalysis experiments.