Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Selective growth of ZnO micro- and nano-structures on fs-laser processed metallic Zn substrates for large area applications

  • Ariza, Rocío
  • Urbieta, A.
  • Ferreiro, A.
  • Rabanal, M. E.
  • Fernández, P.
  • Solís Céspedes, Javier
9 pages, 7 figures, 4 tables, The synthesis of large area micro- and nano-structured ZnO surfaces has been successfully achieved through a two-step process. It involves the irradiation of Zn metal sheets with femtosecond laser pulses (350 fs at 1030 nm) at high repetition rates (100–500 kHz), and fast scanning speeds (cm/s). Subsequently, the irradiated sheets are thermally treated in an Argon flux at 380 °C, a temperature significantly lower than that typically required for growing micro- and nanostructures in ZnO. Fs-laser irradiation promotes the initial development of topography and the localized oxidation of the metal. This enables the further growth of micro- and nanostructures at preferential sites with good crystalline quality and luminescent properties. Analysis of the material at different processing steps shows that the initial laser-induced oxidation is crucial in defining ZnO growth mechanisms upon thermal treatment, and determining the final properties. We have tested the potential use of these structures as reusable photocalyst. The ease of catalyst recovery in photocatalysis experiments and the degree of degradation achieved may be considered as key performance indicators. Photocatalytic activity tests performed with a Rhodamine B solution showed degradation values up to 43 % over 90 min. The morphology of the samples remains unaltered after photocatalysis experiments., The authors are grateful to MCIN/AEI/10.13039/501100011033 for the financial support through grants PID2020–112770RB-C21, PID2019–106631GB-C43 and CPP2022–009910, UCM under project PR3/23–30813, and project S2018/NMT-4411. RA acknowledges the funding from a Marie Skłodowska-Curie Postdoctoral grant (No 101149132)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Formation and Coherent Propagation of Femtosecond-Laser-Induced Periodic Surface Structures (LIPSS) in Fluorine-Doped Tin Oxide: Control, Potential Applications, and Challenges

  • Gómez-Muñoz, Gonzalo
  • Ariza, Rocío
  • Núñez-Galvez, Fernando
  • López-Flores, Víctor
  • Cabello, Fátima
  • Sotillo, Belén
  • Prieto, Carlos
  • Gonzalo de los Reyes, J.
  • García-López, Francisco Javier
  • Fernández Sánchez, Paloma
  • López-Sánchez, Carmen
  • Solís Céspedes, Javier
16 pages, 13 figures, 1 table, We have analyzed the formation and coherent propagation of laser-induced periodic surface structures (LIPSS) upon fs-laser irradiation of fluorine-doped tin oxide (FTO) films. The aim is the generation of large electrical anisotropies in macroscopic areas for applications including laser-written transparent heaters, sensors, or substrates for electrically controllable wettability, among others. The films have been processed with high-repetition-rate (hundreds of kHz) fs-laser pulses at 1030 nm using different laser (fluence and pulse duration) and scanning parameters (speed and line overlap). Optimal LIPSS formation and coherent propagation are conditioned by the dynamic evolution of the F content in the laser-processed regions that can be controlled via processing parameters. However, the homogeneity in the spatial distribution of F in the microscale in the pristine samples can generate important issues that are carefully considered and discussed in the present work. Still, the formation of optically and electrically highly anisotropic surfaces for laser scanning speeds well above 1.0 m/s has been demonstrated, reaching electrical resistivity anisotropy factors of >103. Consequently, the potential development of large-area applications using LIPSS-structured FTO films seems feasible, as we have demonstrated by fabricating an efficient laser-written electrothermal transparent device as a proof-of-concept., This research was partially funded by the Spanish Ministry of Science, Innovation and Universities (MICIU), the Spanish Research Agency (AEI- MICIU), and the European Regional Development Fund (ERDF) through grant numbers PID2023148178OB-C22 (HyperSpec) and PID2024-156974OB-C21 (SLIM-2P), funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe”. This research was also partially funded by the Consejeri a de Educación, Juventud y Deporte, Comunidad de Madrid through grant number TEC-2024/TEC-85 (MATRIX-CM). R.A. acknowledges the funding from a Marie Skłodowska Curie Postdoctoral grant (N° 101149132)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Generating a Stable Higher-Symmetry CsPbI3 Perovskite Phase in Ambient Conditions: Unveiling the Stabilization Mechanism

  • Saha, R. A.
  • Papadopoulou, Athina
  • Ariza, Rocío
  • Degutis, Giedrius
  • Skvortsova, Irina
  • Braeckevelt, Tom
  • De Angelis, Francesco
  • Solano, Eduardo
  • de Sousa Gouveia Dos Anjos, João Pedro
  • Pintor Monroy, Maria Isabel
  • Mongilyov, Ilya
  • Goderis, Bart
  • Rubio-Zuazo, J.
  • Genoe, Jan
  • Meneghini, Carlo
  • Steele, Julian A.
  • Bals, Sara
  • Van Speybroeck, Veronique
  • Hofkens, Johan
  • Roeffaers, M.B.J.
Black-phase cesium lead iodide (CsPbI3) is a promising candidate for high-efficiency perovskite optoelectronics, but its instability under ambient conditions remains a major challenge. Among several strategies, dimethylammonium iodide (DMAI) has emerged as a potential stabilizer; however, inconsistencies in phase stability (3–7 days) and lower solar power conversion efficiencies (∼20 vs ∼27% for hybrid perovskites) highlight the need for further improvements. This study not only demonstrates enhanced stabilization of the high-symmetry black phase of CsPbI3 and improved film morphology through optimized composition and annealing conditions but also more importantly provides detailed mechanistic insights obtained from comprehensive experimental and theoretical analyses. Systematic tuning of the DMAI concentration (1.2 M), annealing temperature (200 °C, 1 min), and Cs+ substitution (12–15%) significantly extends phase stability to 7 days under ambient conditions (35–52% relative humidity) and maintains stability even after 16 months in a drybox environment by reducing orthorhombic strain and octahedral tilting. Additionally, a minor (∼5%) zero-dimensional (0D) Cs4PbI6 phase fills pinholes, enhancing the film quality. Optimized photodiodes exhibit a low dark current (∼1 μA/cm2), high external quantum efficiency (∼80% at −2 V), and a ≥100 dB linear dynamic range. These findings provide mechanistic insights into the stabilization of the black phase of CsPbI3, advancing the development of more stable and efficient perovskite-based optoelectronic devices., This work was supported by iBOF-21-085 PERsist and Internal Funds KU Leuven (C14/23/090). The authors acknowledge financial support from the Fund for Scientific Research Flanders (FWO) under Project Numbers S004322N (GigaPixel) and G0A5923N (SUSTRAINABLE). I.S. acknowledges the SB-FWO Project 1SHA024N for funding. V.V.S. acknowledges the Research Fund of Ghent University (BOF) for its financial support. The computational resources and services used in this work were provided by VSC (Flemish Supercomputer Center), funded by the Research Foundation─Flanders (FWO), and the Flemish Government. R.A.S., E.S., and J.A.S. thank the staff of the BL11 NCD-SWEET beamline for their assistance in recording the synchrotron GIWAXS data. R.A. acknowledges financial support from Marie Skłodowska-Curie Grant Agreement No. 101149132., Peer reviewed