Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Feedforward control application in aerobic and anoxic biotrickling filters for H2S removal from biogas

  • López, L.R.
  • Mora, M.
  • Almengló Cordero, Fernando
  • Baeza, J.A.
  • Ramírez Muñoz, Martín
  • Lafuente, Javier
  • Cantero Moreno, Domingo
  • Gabriel, D.
BACKGROUND Feedforward control was implemented at laboratory scale in an aerobic and an anoxic biotrickling filter (BTF) operating under fluctuating H2S loading rate (LR) conditions in order to show the capabilities and added value of this control strategy. Dynamic, long-term tests with variable H2S LR were performed to simulate disturbances in the inlet gas concentration with and without the implementation of a feedforward control loop based on trickling liquid velocity (TLV) and nitrate feeding rate manipulation for the aerobic and anoxic BTFs, respectively. RESULTS An average LR of 80 g S-H2S m–3 h–1 with peaks and valleys of 141 and 28 gS-H2S m–3 h–1 were tested. At the highest H2S LR, a 68.4% and 62.6% reduction of maximum outlet H2S concentration, and 50.0% and 26.6% reduction of H2S cumulative mass emitted were reached in the aerobic and anoxic BTFs, respectively, thanks to the application of feedforward control strategies. The sulfate selectivity in the aerobic BTF was enhanced up to 100.6 ± 5.0% under controlled conditions. In the anoxic BTF the sulfate selectivity was kept constant at 32.8% ± 0.8%. CONCLUSION Despite demonstrating that the feedforward controller significantly reduced the impact of disturbances, the utilization of TLV as manipulated variable in the aerobic reactor showed performance problems. However, the feedforward control through nitrate addition was shown to be an adequate, robust strategy for reducing the impact of load perturbation in anoxic BTFs.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

PID control system for biogas desulfurization under anoxic conditions

  • Brito, Javier
  • Almengló Cordero, Fernando
  • Ramírez Muñoz, Martín
  • Gómez Montes de Oca, José Manuel
  • Cantero Moreno, Domingo
BACKGROUND A high H2S elimination capacity has been achieved by anoxic biotrickling filters but accurate control of the nitrate dosage is required. Different control strategies have been used in biotrickling filters but proportional-integral-derivative (PID) control studies have not been reported to date. The aim of this study was to demonstrate the stability and robustness of PID control in an anoxic biotrickling filter. RESULTS Three PID tuning methods were tested: Ziegler–Nichols, Approximate M-constrained integral gain optimization (AMIGO), and maintained oscillation. The best results were obtained using PID control by the maintained oscillation method, where the system reached stabilization 0.41 h after the H2S inlet step. Moreover, the nitrate consumption was 15.4% lower than that without control. CONCLUSION The biotrickling filter operated with a PID control strategy proved to be highly stable and robust against the perturbations and disturbances evaluated. The control system was able to operate satisfactorily to a change in the set-point of the outlet H2S concentrations from 25 to 200 ppmV. The desulfurized biogas could be fed directly to an internal combustion engine or solid oxide fuel cell (SOFC) equipped with a zeolite clean unit. © 2017 Society of Chemical Industry
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Integration of a nitrification bioreactor and an anoxic biotrickling filter for simultaneous ammonium-rich water treatment and biogas desulfurization

  • Cano, Patricio I.
  • Almengló Cordero, Fernando
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
A preliminary assessment has been carried out on the integration of an anoxic biotrickling filter and a nitrification bioreactor for the simultaneous treatment of ammonium-rich water and H2S contained in a biogas stream. The nutrient consumption in the biotrickling filter was as follows (mol−1 NO3−-N): 6.3·10−4 ± 1.2·10−4 mol PO43−-P, 0.04 ± 0.05 mol NH4+-N and 0.04 ± 0.03 mol K+-K. Furthermore, it was possible to supply a mixture of biogenic NO3− and NO2− into the biotrickling filter from the nitrification bioreactor to obtain a maximum elimination capacity of 152 gH2S–S m−3 h−1. The equivalence between the two compounds was 1 mol NO3−-N equal to 1.6 mol NO2−-N. The biotrickling filter was also operated under a stepped variable inlet load (30–100 gH2S–S m−3 h−1) and outlet H2S concentrations of less than 150 ppmV were obtained. It was also possible to maintain the outlet H2S concentration close to 15 ppmV with a feedback controller by manipulating the feed flow (in the nitrification bioreactor). Two stepped variable inlet loads were tested (60–111 and 16–102 gH2S–S m−3 h−1) under this type of control. The implementation of feedback control could enable the exploitation of biogas in a fuel cell, since the H2S concentrations were 15.1 ± 4.3 and 15.0 ± 3.4 ppmV. Finally, the anoxic biotrickling filter experienced partial denitrification and this implied a loss of the desulfurization effectiveness related to SO42− production. © 2021 The Authors, The Spanish Government ( Ministerio de Economía y Competitividad ) and European FEDER funds provided financial support through the project CTM2012-37927-C03 ‘Monitoring, modelling and control towards the optimization of anoxic and aerobic desulfurizing biotrickling filters’.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Characterization of eubacterial communities by Denaturing Gradient Gel Electrophoresis (DGGE) and Next Generation Sequencing (NGS) in a desulfurization biotrickling filter using progressive changes of nitrate and nitrite as final electron acceptors

  • Brito García, Javier
  • Valle Gallardo, Antonio
  • Almengló Cordero, Fernando
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
Los biofiltros percoladores anóxicos (BTF) representan una tecnología con gran capacidad y eficiencia de eliminación de ácido sulfhídrico (H2S) que ha sido ampliamente estudiada para la desulfuración del biogás. En este estudio, se realizaron tres modos de operación mediante cambios de aceptor final de electrones utilizando nitrato y nitrito durante un periodo de operación de 520 días. La estabilidad y el rendimiento del BTF anóxico se mantuvieron cuando se aplicó al sistema una perturbación significativa que implicaba el cambio progresivo de nitrato a nitrito y viceversa. El impacto de los cambios de aceptor final de electrones en la comunidad microbiana se caracterizó mediante electroforesis en gel con gradiente desnaturalizante (DGGE) y secuenciación masiva de nueva generación (NGS). Ambas plataformas revelaron que la comunidad microbiana sufrió cambios durante las perturbaciones en el biorreactor, pero las poblaciones fueron resilientes porque la capacidad de eliminación no cambió significativamente. Los principales fila encontrados fueron Proteobacterias y Bacteroidetes y los principales géneros de bacterias descritos fueron Sulfurimonas y Thiobacillus, dichos géneros están descritos como bacterias reductoras de nitrato y sulfuro-oxidantes (NR-SOB), por tanto son las bacterias que llevan a cabo principalmente el proceso de biodesulfuración.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Modeling and control strategies for anoxic biotrickling filtration in biogas purification

  • Almengló Cordero, Fernando
  • Ramírez Muñoz, Martín
  • Gómez Montes de Oca, José Manuel
  • Cantero Moreno, Domingo
  • Gamisans, Xavier
  • Dorado, Antonio David
BACKGROUND Anoxic biotrickling filters have been used to 'sweeten' biogas. Nevertheless, the cost and availability of large amounts of nitrate could limit the use of this technology in comparison with aerobic biotrickling filters. The development of a dynamic mathematical model would be useful for the design of control strategies with regard to nitrate dosage. RESULTS A dynamic model has been developed to describe the performance of an anoxic biotrickling filter for biogas desulfurization. The model considers the most relevant phenomena involved in biotrickling filter operation: advection, absorption, diffusion and biodegradation. Moreover, a fraction of the liquid phase is stagnant – an assumption that increases the importance of diffusion phenomena for low liquid flow rates. Once the model had been validated, six control strategies were analyzed for different scenarios and purposes: i.e. to minimize nitrate consumption and/or to maximize H2S removal efficiency. CONCLUSION The mathematical model developed from the description of the phenomena involved in the process is a powerful tool to evaluate all possible strategies when considering and quantifying the savings and improvements in different operating modes.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Life Cycle Assessment of different physical-chemical and biological technologies for biogas desulfurization in sewage treatment plants

  • Cano Santana, Patricio Iván
  • Colón, Joan
  • Ramírez Muñoz, Martín
  • Lafuente, Javier
  • Gabriel, David
  • Cantero Moreno, Domingo
Biogas desulfurization can be carried out by physical-chemical or biological technologies. Biological technologies are generally described as more environmentally friendly than physical-chemical techniques, although it is difficult to find studies in which the associated environmental burdens are compared. Therefore, the aim of the work described here was to perform a life cycle assessment to compare the environmental impact of four common desulfurization technologies for hydrogen sulfide removal from biogas produced in sewage treatment plants. The desulfurization technologies studied were aerobic biotrickling filtration, anoxic biotrickling filtration, caustic chemical scrubbing and adsorption on impregnated activated carbon. The environmental assessment was extended with a Capital Expenditures (CAPEX) and Operational Expense (OPEX) analysis. Furthermore, an extra scenario (no desulfurization with biogas combustion) was compared with biogas desulfurization by aerobic biofiltration coupled to energy valorization (best-case treatment scenario). Results indicate that biological technologies are much more favorable in most environmental impact categories than physicalchemical technologies and, as expected, are more favorable than the non-treatment scenario. In all desulfurization technologies the most contributing stage to the total environmental burdens was the daily desulfurization operation. The chemical scrubber was the worst scenario except for the “Climate Change”. In terms of the “Climate Change” (carbon dioxide equivalent emission), aerobic and anoxic desulfurization would emit 13.9 and 18.7 kg CO2 kg-1 S-H2S treated, respectively. The anoxic process could be improved to emit only 7.2 kg CO2 kg-1 S-H2S treated if the nitrate source was produced in a nitrification reactor built at the sewage treatment plant. Caustic chemical scrubber desulfurization and impregnated activated carbon desulfurization would emit 30.0 and 42.1 kg CO2 kg-1 S-H2S treated, respectively. To all impact categories, the contribution of sulfur compounds was less than 5%. The aerobic biotrickling filtration had the lower environmental impacts. However, the anoxic biotrickling filtration was the best approach if a nitrification reactor was already on-site., The Spanish Government provided financial support to carry out the research work through the project CTM2012-37927-C03 “Monitoring, modelling and control towards the optimization of anoxic and aerobic desulfurizing biotrickling filters”. Department of Chemical, Biological and Environmental Engi neering (Universitat Autonoma de Barcelona) is a unit of Biochemical Engineering of the Xarxa de Referencia en Biotecnologia de Catalunya (XRB), Generalitat de Catalunya.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Effect of gas-liquid flow pattern and microbial diversity analysis of a pilot-scale biotrickling filter for anoxic biogas desulfurization

  • Almengló Cordero, Fernando
  • Bezerra, T.
  • Lafuente, Javier
  • Gabriel, D.
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
Hydrogen sulfide removal from biogas was studied under anoxic conditions in a pilot-scale biotrickling filter operated under counter- and co-current gas-liquid flow patterns. The best performance was found under counter-current conditions (maximum elimination capacity of 140 gS m−3 h−1). Nevertheless, switching conditions between co- and counter-current flow lead to a favorable redistribution of biomass and elemental sulfur along the bed height. Moreover, elemental sulfur was oxidized to sulfate when the feeding biogas was disconnected and the supply of nitrate (electron acceptor) was maintained. Removal of elemental sulfur was important to prevent clogging in the packed bed and, thereby, to increase the lifespan of the packed bed between maintenance episodes. The larger elemental sulfur removal rate during shutdowns was 59.1 gS m−3 h−1. Tag-encoded FLX amplicon pyrosequencing was used to study the diversity of bacteria under co-current flow pattern with liquid recirculation and counter-current mode with a single-pass flow of the liquid phase. The main desulfurizing bacteria were Sedimenticola while significant role of heterotrophic, opportunistic species was envisaged. Remarkable differences between communities were found when a single-pass flow of industrial water was fed to the biotrickling filter.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Progressive change from nitrate to nitrite as the electron acceptor for the oxidation of H2S under feedback control in an anoxic biotrickling filter

  • Brito, Javier
  • Valle Gallardo, Antonio
  • Almengló Cordero, Fernando
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
Nitrate has been progressively replaced by nitrite as the electron acceptor in the oxidation of H2S from biogas mimic by an anoxic biotrickling filter. Perturbations in the inlet H2S concentration with and without the implementation of feedback controllers have been evaluated. Nitrite was successfully used without decreasing the H2S removal efficiency (94.74 ± 0.01%). Moreover, a PID controller allowed the sulfate selectivity to be maintained and reduced the maximum outlet H2S concentration when compared to the system without control (54.4–64.4%), although elemental sulfur was the main oxidation product. On using ORP control the main disadvantage was the production of peaks in the outlet H2S concentration. The stability and resilience of the biological system were assessed by analyzing the microbial community profiles by 16S rDNA-denaturing gradient gel electrophoresis (DDGE). The modification of the electron acceptor led to a reduction in the diversity and increased the dominance of the microbial populations.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Profiling of oxygen in biofilms using individually addressable disk microelectrodes on a microfabricated needle

  • Moya, Ana
  • Guimerà, Xavier
  • del Campo, Francisco Javier
  • Prats-Alfonso, Elisabet
  • Dorado, Antonio David
  • Baeza, Mireia
  • Villa, Rosa
  • Gabriel, David
  • Gamisans, Xavier
  • Gabriel, Gemma
A novel microelectrode array sensor was fabricated using MEMS technology on a needle, and then applied to real-time measurement of dissolved oxygen (DO) inside biofilms. The sensor consists of eleven gold disk microelectrodes, a rectangular auxiliary electrode along them, and an external and internal reference electrode. Three kinds of sensors were designed and their responses were characterized and evaluated under various conditions. The arrays exhibit a linear response to DO in the 0–8 mg·L<sup>−1</sup> concentration range in water, high sensitivity, repeatability, and low limits of detection (<0.11 mg·L<sup>−1</sup> of DO) and quantification (0.38 mg·L<sup>−1</sup> DO). The sensors were validated against a commercial Clark-type microelectrode and applied to profiling of DO in a heterotrophic biofilm cultivated in a flat-plate bioreactor. It is shown that the sensor array can provide a multipoint, simultaneous snapshot profile of DO inside a biofilm with high spatial resolution due to its micrometric dimensions. We conclude that this new sensor array represents a powerful tool for sensing of DO biofilms and in numerous bioprocesses.[Figure not available: see fulltext.], This work has been founded by projects DPI2011-28262-C04 and CTM2012-37927-C03/FEDER, financed by the Ministerio de Economía y Competitividad (Spain). AM gratefully ac-knowledges an FPI-2012 pre-doctoral scholarship, (it funded her PhD studies at Universitat Autònoma de Barcelona), and XG also acknowl- edges an FPI-UPC pre-doctoral scholarship, both from Ministerio de Economía y Competitividad (Spain)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dynamic characterization of external and internal mass transport in heterotrophic biofilms from microsensors measurements

  • Guimerà, Xavier
  • Dorado, Antonio David
  • Bonsfills, Anna
  • Gabriel, Gemma
  • Gabriel, David
  • Gamisans, Xavier
Knowledge of mass transport mechanisms in biofilm-based technologies such as biofilters is essential to improve bioreactors performance by preventing mass transport limitation. External and internal mass transport in biofilms was characterized in heterotrophic biofilms grown on a flat plate bioreactor. Mass transport resistance through the liquid-biofilm interphase and diffusion within biofilms were quantified by in situ measurements using microsensors with a high spatial resolution (<50 μm). Experimental conditions were selected using a mathematical procedure based on the Fisher Information Matrix to increase the reliability of experimental data and minimize confidence intervals of estimated mass transport coefficients. The sensitivity of external and internal mass transport resistances to flow conditions within the range of typical fluid velocities over biofilms (Reynolds numbers between 0.5 and 7) was assessed. Estimated external mass transfer coefficients at different liquid phase flow velocities showed discrepancies with studies considering laminar conditions in the diffusive boundary layer near the liquid-biofilm interphase. The correlation of effective diffusivity with flow velocities showed that the heterogeneous structure of biofilms defines the transport mechanisms inside biofilms. Internal mass transport was driven by diffusion through cell clusters and aggregates at Re below 2.8. Conversely, mass transport was driven by advection within pores, voids and water channels at Re above 5.6. Between both flow velocities, mass transport occurred by a combination of advection and diffusion. Effective diffusivities estimated at different biofilm densities showed a linear increase of mass transport resistance due to a porosity decrease up to biofilm densities of 50 g VSS·L(-1). Mass transport was strongly limited at higher biofilm densities. Internal mass transport results were used to propose an empirical correlation to assess the effective diffusivity within biofilms considering the influence of hydrodynamics and biofilm density., This work has been founded by the project CTM2012-37927-C03-02, financed by the Ministerio de Economía y Competitividad (Spain). Xavier Guimer a acknowledges a FPI-UPC predoctoral scholarship, from Universitat Polit ecnica de Catalunya. The authors also want to acknowledge the Biomedical Applications Group (GAB), and especially to Ana Moya, from the Barcelona Microelec-tronics Institute (IMB-CNM, CSIC) their work in the DO-MEA sensor development., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Dynamic characterization of external and internal mass transport in heterotrophic biofilms from microsensors measurements

  • Guimerà Villalba, Xavier
  • Dorado Castaño, Antonio David
  • Bonsfills Pedrós, Anna
  • Gabriel Buguña, Gemma
  • Gabriel Buguña, David
  • Gamisans Noguera, Javier
Peer Reviewed, Preprint
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Development of a novel microsensor for the study of oxygen profiles in biofilms

  • Guimerà Villalba, Xavier
  • Moya Lara, Ana
  • Prats Alfonso, Elisabet
  • Dorado Castaño, Antonio David
  • Villa, Rosa
  • Gamisans Noguera, Javier
  • Gabriel Buguña, David
  • Gabriel Buguña, Gemma
Understanding of the processes taking place inside biofilms is a key parameter to progress in the optimization of biofiltration technologies. This study was conducted with the aim of developing a novel dissolved oxygen (DO) microsensor specially designed for biofilms monitoring. The microsensor was fabricated through standard photolithography techniques, resulting in a microelectrodes array (MEA) of 11 gold circular working electrodes, with a diameter of 50 µm , and a gold reference electrode, which allows obtaining a snapshot oxygen profile of 1 mm of depth. The performance of the sensor was fully characterized under different conditions, inwhich the sensor presented high sensitivity and repeatability, and low detection and quantification limits. Monitoring of sensor performance showed a stable and reliable response. The developed sensor was used in obtaining micropofiles in an aerobic heterotrophic biofilm, showing similar response to Clark-type commercial microsensors. These studies concluded that the novel MEA sensor for DO monitoring allows obtaining oxygen profiles within biofilms, becoming a useful tool for the research of many biological applications., Postprint (author's final draft)
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Model-based analysis of feedback control strategies in aerobic biotrickling filters for biogas desulfurization

  • López, Luis Rafael
  • Mora Garrido, Mabel|||0000-0002-2979-3601
  • Van der Heyden, Caroline
  • Baeza, Juan Antonio|||0000-0003-1290-1669
  • Volcke, Eveline
  • Gabriel, David|||0000-0002-7713-4192
Biotrickling filters are one of the most widely used biological technologies to perform biogas desulfurization. Their industrial application has been hampered due to the difficulty to achieve a robust and reliable operation of this bioreactor. Specifically, biotrickling filters process performance is affected mostly by fluctuations in the hydrogen sulfide (H2S) loading rate due to changes in the gas inlet concentration or in the volumetric gas flowrate. The process can be controlled by means of the regulation of the air flowrate (AFR) to control the oxygen (O2) gas outlet concentration ([O2]out) and the trickling liquid velocity (TLV) to control the H2S gas outlet concentration ([H2S]out). In this work, efforts were placed towards the understanding and development of control strategies in biological H2S removal in a biotrickling filter under aerobic conditions. Classical proportional and proportional-integral feedback controllers were applied in a model of an aerobic biotrickling filter for biogas desulfurization. Two different control loops were studied: (i) AFR Closed-Loop based on AFR regulation to control the [O2]out, and (ii) TLV Closed-Loop based on TLV regulation to control the [H2S]out. AFR regulation span was limited to values so that corresponds to biogas dilution factors that would give a biogas mixture with a minimum methane content in air, far from those values required to obtain an explosive mixture. A minimum TLV of 5.9 m h-1 was applied to provide the nutrients and moisture to the packed bed and a maximum TLV of 28.3 m h-1 was set to prevent biotrickling filter (BTF) flooding. Control loops were evaluated with a stepwise increase from 2000 ppmv until 6000 ppmv and with changes in the biogas flowrate using stepwise increments from 61.5 L h-1 (EBRT = 118 s) to 184.5 L h-1 (EBRT = 48.4 s). Controller parameters were determined based on time-integral criteria and simple criteria such as stability and oscillatory controller response. Before implementing the control strategies, two different mass transfer correlations were evaluated to study the effect of the manipulable variables. Open-loop behavior was also studied to determine the impact of control strategies on process performance variables such as removal efficiency, sulfate and sulfur selectivity, and oxygen consumption. AFR regulation efficiently controlled [O2]out; however, the impact on process performance parameters was not as great as when TLV was regulated to control [H2S]out. This model-based analysis provided valuable information about the controllability limits of each strategy and the impact that each strategy can have on the process performance.