Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hydrogen production from pine and poplar bio-oils by catalytic steam reforming. Influence of the bio-oil composition on the process

  • Remón, J.
  • Broust, F.
  • Volle, G.
  • García, L.
  • Arauzo, J.
The catalytic steam reforming of four different aqueous fractions of bio-oil has been carried out in a fixed bed reactor at 650 °C and atmospheric pressure using a Ni–Co/Al–Mg catalyst, employing a spatial time of 4 g catalyst min/g organics. The chemical analysis of the aqueous fractions revealed that the source of biomass (pine or poplar sawdust) and the pyrolysis unit significantly influenced the chemical composition of these liquids. Depending on their chemical composition, the initial H2 yield varied from 0.101 to 0.182 g H2/g organics and the initial CO2 yield from 0.814 to 1.28 g CO2/g organics during their catalytic reforming. Regarding catalytic stability, higher catalyst deactivation took place during the reforming of the two pine bio-oil aqueous fractions. The reforming results of the four aqueous fractions have been correlated to their chemical compositions using statistical empirical additive models developed using the Bayesian Information Criterion (BIC). This strategy enabled the identification of the chemical compounds responsible for the most significant variations observed during the reforming of the liquids. The different proportions of acetic acid and furfural in the liquids had the greatest impact on the reforming results. Acetic acid was identified as a compound with low reactivity and low coke formation. In contrast, furfural was found to have high reactivity and a high tendency to produce coke in the reforming process. Additional reforming experiments conducted with acetic acid, phenol, furfural, levoglucosan and guaiacol helped to confirm and explain the results obtained during the catalytic steam reforming of the aqueous fractions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ni/Al-Mg-O solids modified with Co or Cu for the catalytic steam reforming of bio-oil

  • Remon, J.
  • Medrano, J.A.
  • Bimbela, F.
  • Garcia, L.
  • Arauzo, J.
An environmentally friendly method of producing a hydrogen rich gas is the catalytic steam reforming of bio-oil. This requires the development of a catalyst appropriate for the process. In the present work, five different research catalysts have been prepared and tested. A Ni/AlMg catalyst was selected as a reference. Modifications to the catalyst were studied, incorporating Co or Cu by coprecipitation or by incipient wetness impregnation. The experiments took place at 650 °C and atmospheric pressure in a fixed bed and in a fluidized bed reactor, using an aqueous fraction (S/C = 7.6 mol H2O/mol C) of pine sawdust bio-oil. A spatial time (W/morg) of 4 g catalyst min/g organics and an u/umf ratio of 10 (in fluidized bed) were used. In both reactors, the coprecipitated NiCo/AlMg catalyst showed the best performance. Over a period of 2 h, 0.138 g H2/g organics and 80% carbon conversion to gas were obtained in the fixed bed reactor. The catalyst deactivation rate was higher when the steam reforming took place in the fixed bed reactor, although the initial H2 and CO2 yields were higher. In contrast, the stability of the catalysts was higher in the fluidized bed reactor. Elemental analysis, FESEM and TPO analyses of some of the catalysts revealed a relationship between their stability and the quantity and characteristics of the coke deposited on their surface.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Production of a hydrogen-rich gas from fast pyrolysis bio-oils: Comparison between homogeneous and catalytic steam reforming routes

  • Remón,J.
  • Broust,F.
  • Valette,J.
  • Chhiti,Y.
  • Alava,I.
  • Fernandez-Akarregi,A.
  • Arauzo,J.
  • Garcia,L.
The aim of the present work is to produce hydrogen from biomass through bio-oil. Two possible upgrading routes are compared: catalytic and non-catalytic steam reforming of bio-oils. The main originality of the paper is to cover all the steps involved in both routes: the fast pyrolysis step to produce the bio-oils, the water extraction for obtaining the bio-oil aqueous fractions and the final steam reforming of the liquids. Two reactors were used in the first pyrolysis step to produce bio-oils from the same wood feedstock: a fluidized bed and a spouted bed. The mass balances and the compositions of both batches of bio-oils and aqueous fractions were in good agreement between both processes. Carboxylic acids, alcohols, aldehydes, ketones, furans, sugars and aromatics were the main compounds detected and quantified. In the steam reforming experiments, catalytic and non-catalytic processes were tested and compared to produce a hydrogen-rich gas from the bio-oils and the aqueous fractions. Moreover, two different catalytic reactors were tested in the catalytic process (a fixed and a fluidized bed). Under the experimental conditions tested, the H2 yields were as follows: catalytic steam reforming of the aqueous fractions in fixed bed (0.17 g H2/g organics) > non-catalytic steam reforming of the bio-oils (0.14 g H2/g organics) > non-catalytic steam reforming of the aqueous fractions (0.13 g H2/g organics) > catalytic steam reforming of the aqueous fractions in fluidized bed (0.07 g H2/g organics). These different H2 yields are a consequence of the different temperatures used in the reforming processes (650 °C and 1400 °C for the catalytic and the non-catalytic, respectively) as well as the high spatial velocity employed in the catalytic tests, which was not sufficiently low to reach equilibrium in the fluidized bed reactor.