Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hydrogen production from pine and poplar bio-oils by catalytic steam reforming. Influence of the bio-oil composition on the process

  • Remón, J.
  • Broust, F.
  • Volle, G.
  • García, L.
  • Arauzo, J.
The catalytic steam reforming of four different aqueous fractions of bio-oil has been carried out in a fixed bed reactor at 650 °C and atmospheric pressure using a Ni–Co/Al–Mg catalyst, employing a spatial time of 4 g catalyst min/g organics. The chemical analysis of the aqueous fractions revealed that the source of biomass (pine or poplar sawdust) and the pyrolysis unit significantly influenced the chemical composition of these liquids. Depending on their chemical composition, the initial H2 yield varied from 0.101 to 0.182 g H2/g organics and the initial CO2 yield from 0.814 to 1.28 g CO2/g organics during their catalytic reforming. Regarding catalytic stability, higher catalyst deactivation took place during the reforming of the two pine bio-oil aqueous fractions. The reforming results of the four aqueous fractions have been correlated to their chemical compositions using statistical empirical additive models developed using the Bayesian Information Criterion (BIC). This strategy enabled the identification of the chemical compounds responsible for the most significant variations observed during the reforming of the liquids. The different proportions of acetic acid and furfural in the liquids had the greatest impact on the reforming results. Acetic acid was identified as a compound with low reactivity and low coke formation. In contrast, furfural was found to have high reactivity and a high tendency to produce coke in the reforming process. Additional reforming experiments conducted with acetic acid, phenol, furfural, levoglucosan and guaiacol helped to confirm and explain the results obtained during the catalytic steam reforming of the aqueous fractions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Oxy-co-Firing in Fluidized Beds: Control of Sulfur Emissions and Assessment of Corrosion Issues

  • Mayoral, M.C.
  • Díez, L.I.
  • Lupiáñez, C.
  • Espatolero, S.
  • Andrés, J.M.
The main objective of this work is to experimentally analyse the effect of firing blends of coal and biomass in oxy-firing atmospheres on SO2 emissions and deposition/corrosion issues. The research has been conducted in a lab-scale fluidized bed unit, and chemical reactivity of deposited species has been simulated at bench scale. Two very different Spanish coals were selected for the oxy-combustion experiments: anthracite, with a very low volatile matter, and lignite with high sulphur content. As concerns the biomass, a short campaign was conducted with forest residues, but most effort was done firing corn stover (with three different chlorine levels). The experimental matrix was designed to analyse the effects of the following parameters: atmosphere (air vs. O2/CO2), coal-to-biomass ratio in the blend (90/10% vs. 80/20%) and bed temperature (850-900 °C). Control of SO2 emissions was largely dependent on the governing desulfurization mechanism, while chlorine in the biomass plays a role in the condensed alkali sulfates. No significant deposition rates were detected even for the higher biomass shares in the blend (20%). Only when corn stover with the highest chlorine content (2%) was fired, a thick deposition scale was found. For the original corn stover, oxy-firing barely affects the deposition rate and slightly reduces the corrosion risk in comparison to conventional air-firing.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

The role of limestone during fluidized bed oxy-combustion of coal and biomass

  • Lupiáñez, C.
  • Mayoral, M.C.
  • Díez, L. I.
  • Pueyo, E.
  • Espatolero, S.
  • Andrés, J.M.
The interest in bio-CCS technologies is growing due to their potential to reduce CO2 emission in power generation. Oxy-co-firing in fluidized-bed units is one of the available techniques to develop bio-CCS, offering wide fuel flexibility and low SO2 and NOx emissions. This paper discusses the results of an experimental campaign carried out in a lab-scale fluidized bed reactor. The work focuses on the influence of limestone when oxy-firing blends of lignite and corn stover. Two different types of limestone with two Ca:S molar ratios were tested, and operational conditions were selected to compare the mechanisms governing desulphurization. Emissions of SO2, NO and HCl, together with deposition rates and ash mineralogy are studied in the paper. SO2 capture increases with the Ca:S ratio and bed temperature, but to a different extent depending on the limestone fragmentation. The amount of NO emitted rises with the Ca:S ratio and the presence of calcined limestone (indirect desulphurization). The HCl concentration in the gas phase is dominated by alkali sulfation. Finally, the conditions for the highest desulphurization efficiency diminished the deposition rates, but increased the risk for chlorine-induced corrosion.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

On the oxy-combustion of lignite and corn stover in a lab-scale fluidized bed reactor

  • Lupiáñez, Carlos
  • Mayoral, M. Carmen
  • Díez, Luis I.
  • Pueyo, Eloy
  • Espatolero, Sergio
  • Andrés, J. Manuel
This paper addresses an experimental investigation concerning oxy-combustion of coal and biomass in a lab-scale fluidized bed reactor. While co-firing has been widely studied under conventional air conditions, few experiences are available to date for O2/CO2 atmospheres. The research is focused on SO2 and NOx emissions, along with the deposition rates and ashes mineralogy. The influences of the atmosphere (air vs. 30/70% O2/CO2), the coal-to-biomass energy input ratio (80/20%, 90/10%), the chlorine mass fraction in the biomass (0.35%, 1%, 2%) and the Ca:S mole ratio (2.5, 4) are reported and discussed in the paper, for two specific fuels: high sulfur lignite and high chlorine corn stover. Concerning SO2 emissions a correlation among the sulfur and the chlorine contents is clearly detected, being affected by the direct desulfurization mechanism occurring under oxy-firing conditions. The single effect of the chlorine content is found to be almost 1.5% of the desulfurization efficiency. NOx emissions are otherwise more dependent on oxygen excess and CO concentration in the reactor, rather than the fuel share or the chlorine supplied. Thick deposition is only detected when chlorine content in the corn is 2%. Potassium aluminosilication is found to be enhanced in comparison to potassium sulfation under oxy-firing, especially for the highest Ca:S mole ratio: observed aluminosilication is five times higher when Ca:S ratio is increased from 2.5 to 4. A significant enrichment in iron is also detected for the fly ash composition, with an increase of 30–50% in comparison to air combustion.