Pasar al contenido principal

CONTROL DE LA FORMACION DE CONTAMINANTES ORGANICOS HALOGENADOS EN EL TRATAMIENTO TERMICO DE RESIDUOS POR MEDIO DE PRETRATAMIENTOS E INHIBICION

CTQ2016-76608-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ALICANTE

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Inhibiting fly ash reactivity by adding N- and S- containing compounds

  • Soler, Aurora
  • Conesa, Juan A.
  • Ortuño García, Nuria
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
The inhibitory effect of thiourea (TUA), ammonium thiosulfate (TSA) and amidosulfonic acid (ASA) on the reactivity of fly ash air was investigated using a thermobalance at different heating rates (5, 10 and 20 K min−1). A model fly ash (activated carbon + 50 wt% CuCl2·2H2O, pyrolyzed at 700 °C and washed) was used as carbonaceous material. Adding CuCl2·2H2O to the activated carbon led to an increased rate of decomposition with the air's oxygen. TUA and TSA behaved in a similar way, accelerating the decomposition of the model fly ash. ASA also accelerated the decomposition but to a lower extent. We postulate that the increase in decomposition rate is caused by a reaction between carbonaceous material and N and S-containing compounds. The formation of nitrogenated and sulphured compounds was confirmed by TG-MS. A kinetic model based on a single reaction of order 0.6 showed very good correlations with all the heating rates tested in oxidant atmosphere.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Estimation of Industrial Emissions during Pyrolysis and Combustion of Different Wastes Using Laboratory Data

  • Conesa, Juan A.
  • Ortuño García, Nuria
  • Palmer, Damià
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
In our lab, we have been studying the emissions of different pollutants during pyrolysis and combustion of wastes under different conditions for the last three decades. These studies have focused on the effect of temperature and presence of oxygen on the production of different pollutants. Waste decomposition has been studied in a horizontal laboratory scale reactor, but no estimate has been made of the actual emissions in a conventional thermal decomposition system. In the present study, emissions during these wastes’ thermal decomposition were estimated using Aspen HYSYS. In the simulation software, the waste composition (elemental analysis) was given as an input parameter, as well as the gas flow rate used as atmosphere during the decomposition. The emitted hydrocarbons measured in the laboratory were equated to the emission of a single compound (propylene). The simulation permitted calculating the percentage of oxygen in the emitted gas, and the pollutant emissions were then recalculated under standard conditions. The emission of dioxins and furans were estimated under different conditions of decomposition, and an adequate approximation of the waste decomposition in actual incineration systems could be obtained.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Thermal Decomposition of Three Types of Copper Clad Laminates Considering the Influence of an Iron-clay Catalyst in the Production of Pollutants

  • Conesa, Juan A.
  • Ortuño García, Nuria
  • Zielinska, Amelia
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Metal recovering through decomposition in the presence of steam of different wastes has been demonstrated to be an effective method. In the present work, three different types of copper clad laminates (FR4, CEM3 and ROGERS) were subjected to high temperature decomposition, analyzing their performance. Firstly, the samples were analyzed by thermogravimetry, both in the absence and in the presence of oxygen in the atmosphere; FR4 and CEM3 showed a very strong interaction with oxygen, in contrast to ROGERS. Secondly, the laminates underwent oxidative pyrolysis in the presence of steam at 900 °C in a horizontal laboratory furnace; the experiments °were carried out in the presence and in the absence of an iron-clay catalyst, in order to evaluate its effect on the production of pollutants. Analyses of the produced gas and semivolatile species are shown, including polycyclic aromatic hydrocarbons (PAHs), bromophenols (BrPhs) and brominated dioxins and furans (PBDD/Fs). The gaseous emissions are almost limited to methane, hexane, toluene and xylene, and the production of PAHs and other semivolatile compounds is considerably reduced with the use of the iron-clay catalyst. The emissions of BrPhs and PBDD/Fs are also very limited. Comparing among the behavior of the three types of laminates, the emission of brominated compounds is much lower in the gasification of ROGERS, compared to FR4 and CEM3.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Improving efficiency and feasibility of subcritical water debromination of printed circuit boards E-waste via potassium carbonate adding

  • Gandon-Ros, Gerard
  • Soler, Aurora
  • Aracil, Ignacio
  • Gómez-Rico, María Francisca
  • Conesa, Juan A.
  • Aracil, Ignacio|||/items/0485586f-35e8-4be9-b931-2b960ed728d9
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Gómez-Rico, María Francisca|||/items/858ecde1-f676-4a71-982c-77a0fbb2c21c
Waste printed circuit boards (WCBs) were debrominated under hydrothermal treatment, using potassium carbonate as an alkaline additive to improve debromination efficiency (DE). Two different high-pressure reactors were used: a 1-L stirred reactor, where the evolution of the DE was followed over time at a low CO32−/Br− ratio (1:25), and an elementary 0.1-L non-stirred reactor, used to find the optimal parameters and to simplify the hydrothermal debromination (HTD) process. Considering both reactors, experiments were conducted changing the temperature (200 °C, 225 °C, 250 °C, 275 °C), and also the CO32−/Br− anionic ratio (1:50, 1:25, 1:10, 1:5, 1:2.5, 1:1, 2:1, 4:1) and the solid/liquid ratio (1:10, 1:5, 1:2) in the case of the 0.1-L reactor. No metallic catalyst was required. A maximum DE of about 98.9 wt % was reached in the agitated vessel at 275 °C after 4 h, with an additive/bromine ratio of 1:25. Similar DE (99.6 wt %) was also achieved in the non-stirred reactor at only 225 °C and after 2 h, using an additive/bromine ratio of 4:1 and a solid/liquid ratio of only 1:2. Concerning the solid phase behaviour during debromination, only 5 % of the net calorific value (NCV) was lost after a complete HTD treatment of WCB.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Recyclability of four types of plastics exposed to UV irradiation in a marine environment

  • Iñiguez, María Esperanza
  • Conesa, Juan A.
  • Fullana, Andres
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Fullana, Andres|||/items/5a59481d-6a15-41b8-88c9-185b3877ea3a
Plastics are the most abundant products in the world and therefore also represent the largest volume of materials found in the sea. Their resistance to degradation makes them dangerous for the marine environment. In this study, the degradation of the four main plastics (Nylon, Polyethylene (PE), Polypropylene (PP), Polyethylene terephthalate (PET)) found in the sea was observed for 6.5 months as they were exposed to UV irradiation in a marine environment. Data on changes in the physical and chemical properties of each of them were collected in order to evaluate the possibilities of material (mechanical) recycling. A thermobalance was used to look for differences in the thermal decomposition of the plastics during this time. In addition, the mechanical properties of each plastic were studied. Results showed that both thermal and mechanical properties were affected, causing a weakening of the material which became less elastic and more rigid. Furthermore, SEM and AFM images were obtained: they showed cracks, flakes and granular oxidation as well as a loss of homogeneity on the surface of the samples. These changes make mechanical recycling unfeasible, since the quality of the recycled material is insufficient to ensure a high virgin material substitution rate.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Effect of Sodium Chloride and Thiourea on Pollutant Formation during Combustion of Plastics

  • Iñiguez, María Esperanza
  • Conesa, Juan A.
  • Fullana, Andres
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Fullana, Andres|||/items/5a59481d-6a15-41b8-88c9-185b3877ea3a
Thermal decomposition of different samples containing a mixture of plastics (polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), and nylon) combined with NaCl and metal oxides (Fe2O3, CuO) was studied under an air atmosphere at 850 °C using a reactor, followed by analysis of the evolved products. Combustion runs were performed to study how the presence of such compounds influences the production of pollutants. Here, we report the analyses of the emissions of the main gases, as well as volatiles and semivolatiles, including polyaromatic hydrocarbons (PAHs), polychlorinated benzenes and phenols, and polybrominated phenols. Results show that the production of chlorinated pollutants did not increase in the presence of NaCl, but the presence of other metals during the decomposition led to the production of a great amount of pollutants. In this regard, the emission of chlorinated phenols increased from 110 to ca. 250 mg/kg when the sample included a small quantity of a transition metal oxide. Additionally, the presence of an inhibitor—thiourea (TUA)—was tested. Results confirm that adding TUA to the sample reduced these emissions to a considerable extent, with the emission of chlorinated phenols amounting to 65 mg/kg.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Inhibition effect of polyurethane foam waste in dioxin formation

  • Moreno Caballero, Ana Isabel
  • Font, Rafael
  • Gómez-Rico, María Francisca
  • Gómez-Rico, María Francisca|||/items/858ecde1-f676-4a71-982c-77a0fbb2c21c
The present work has been focused on studying the polychlorinated polychlorodibenzo-p-dioxin/furan (PCDD/F) inhibition in the combustion process by prior addition of an inhibitor to the fuel. Three different experiments of combustion were carried out at 850 °C in a laboratory-scale horizontal tubular quartz reactor, and several compounds were analyzed from the flue gas obtained, such as PCDD/Fs, dioxin-like polychlorinated biphenyls (dl-PCBs), NH3, HCN, NOx, HCl, Cl2, chlorobenzenes (ClBzs), chlorophenols (ClPhs), polycyclic aromatic hydrocarbons (PAHs), volatile and other semivolatile organic compounds. The fuel used was a synthetic waste which was composed of sawdust and PVC (95 wt% and 5 wt%, respectively) and the inhibitors studied were polyurethane foam (PUF) that can be found in mattress waste and gases from the oxidative pyrolysis of PUF. Due to the high N content of PUF, a significant decrease of PCDD/F and dl-PCB formation has been obtained in the experimental runs carried out with the inhibitors studied, particularly with the gases from the oxidative pyrolysis of PUF. In addition, it must be noted that emissions of incomplete combustion products have also decreased.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Characterization and Production of Fuel Briquettes Made from Biomass and Plastic Wastes

  • Garrido, María A.
  • Conesa, Juan A.
  • Garcia, Maria Dolores
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes, without using any external binding agent, were investigated. The biomass feedstocks were blended with different ratios of two waste from electrical and electronic equipment (WEEE) plastics (halogen-free wire and printed circuit boards (PCBs)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10–30%), pressures (22–67 MPa) and temperatures (room–130 °C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Pollutant formation in the pyrolysis and combustion of materials combining biomass and e-waste

  • Soler, Aurora
  • Conesa, Juan A.
  • Iñiguez, María Esperanza
  • Ortuño García, Nuria
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Combustion and pyrolysis runs at 850 °C were carried out in a laboratory scale horizontal reactor with different materials combining biomass and waste electrical and electronic equipment (WEEE). Analyses are presented of the carbon oxides, light hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), polychlorinated benzenes (ClBzs), polychlorinated phenols (ClPhs), polybrominated phenols (BrPhs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Results showed that gas emissions were mainly composed of CO and CO2; the high level of CO found in the pyrolytic runs was easily transformed into CO2 by reaction with oxygen. The total amount of light hydrocarbons emitted was higher in the samples containing WEEE, methane being the most abundant light hydrocarbon in all the runs. However, the presence of WEEE reduced the emission of PAHs which decreased with the increase of the oxygen. The total amount of BrPhs increased in the decomposition of the samples containing WEEE, reaching its maximum in pyrolysis runs. Emission of PCDD/Fs was enhanced in pyrolytic conditions and easily decreased in the presence of oxygen.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Pollutant content in marine debris and characterization by thermal decomposition

  • Iñiguez, María Esperanza
  • Conesa, Juan A.
  • Fullana, Andres
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Fullana, Andres|||/items/5a59481d-6a15-41b8-88c9-185b3877ea3a
Marine debris (MDs) produces a wide variety of negative environmental, economic, safety, health and cultural impacts. Most marine litter has a very low decomposition rate (plastics), leading to a gradual accumulation in the coastal and marine environment. Characterization of the MDs has been done in terms of their pollutant content: PAHs, ClBzs, ClPhs, BrPhs, PCDD/Fs and PCBs. The results show that MDs is not a very contaminated waste. Also, thermal decomposition of MDs materials has been studied in a thermobalance at different atmospheres and heating rates. Below 400–500 K, the atmosphere does not affect the thermal degradation of the mentioned waste. However, at temperatures between 500 and 800 K the presence of oxygen accelerates the decomposition. Also, a kinetic model is proposed for the combustion of the MDs, and the decomposition is compared with that of their main constituents, i.e., polyethylene (PE), polystyrene (PS), polypropylene (PP), nylon and polyethylene-terephthalate (PET).
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Hydrothermal carbonization (HTC) of marine plastic debris

  • Iñiguez, María Esperanza
  • Conesa, Juan A.
  • Fullana, Andres
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Fullana, Andres|||/items/5a59481d-6a15-41b8-88c9-185b3877ea3a
Once removed from the sea, some plastics cannot be recycled or reused. This debris has high calorific value which makes it suitable to use as fuel. For this reason, a mixture of plastic materials was subjected to hydrothermal carbonization using seawater as solvent. We could thus examine the characteristics of the final products obtained and test the feasibility of converting marine plastic debris into fuel. Results showed that raising the temperature of the process reduced the inorganic anions content and increased hydrochar NCV. In addition, thermobalance was used to look for differences in the thermal decomposition of the different solid residues, being hydrochar at 300 °C the most affected material. The content of inorganic compounds in the HTC-liquor increases as the process temperature rose. Amides, alcohols and alkanes were the main organic compounds found in all cases. Gases emissions also increased with temperature.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Analysis of Microplastics in Food Samples

  • Conesa, Juan A.
  • Iñiguez, María Esperanza
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
This chapter presents a compilation of the analytical techniques used to detect and analyze microplastics in food. A detailed description of microplastics found in different samples is provided as well as an estimate of the annual intake of these particles. A total of 22–37 milligrams of microplastics per year was found. The factors that can influence the presence of particles in food, especially table salt, are discussed, showing that a background presence of microplastics in the environment can explain a large amount of experimental data.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Emissions of toxic pollutants from co-combustion of demolition and construction wood and household waste fuel blends

  • Edo Giménez, María del Mar
  • Ortuño García, Nuria
  • Persson, Per-Erik
  • Conesa, Juan A.
  • Jansson, Stina
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Four different types of fuel blends containing demolition and construction wood and household waste were combusted in a small-scale experimental set-up to study the effect of fuel composition on the emissions of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), biphenyls (PCBs), chlorobenzenes (PCBzs), chlorophenols (PCPhs) and polycyclic aromatic hydrocarbons (PAHs). Two woody materials, commercial stemwood (ST) and demolition and construction wood (DC) were selected because of the differences in their persistent organic pollutants (POPs), ash and metals content. For household waste, we used a municipal solid waste (MSW) and a refuse-derived fuel (RDF) from MSW with 5–20 wt% and up to 5 wt% food waste content respectively. No clear effect on the formation of pollutants was observed with different food waste content in the fuel blends tested. Combustion of ST-based fuels was very inefficient which led to high PAH emissions (32 ± 3.8 mg/kgfuel). The use of DC clearly increased the total PCDD and PCDF emissions (71 ± 26 μg/kgfuel) and had a clear effect on the formation of toxic congeners (210 ± 87 ng WHO2005-TEQ/kgfuel). The high PCDD and PCDF emissions from DC-based fuels can be attributed to the presence of material contaminants such as small pieces of metals or plastics as well as timber treated with chromated copper arsenate preservatives and pentachlorophenol in the DC source.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Friedman and n-reaction order methods applied to pine needles and polyurethane thermal decompositions

  • Font, Rafael
  • Garrido, María A.
The Friedman method is applied to two processes: flexible polyurethane foam (PU) pyrolysis and pine needle combustion, considering two types of runs: dynamic and dynamic + isothermal. In both cases, the TG and DTG runs are taken into account. For both materials, the Friedman method is applied twice: one considering only the dynamic runs and the other considering all runs, dynamic and dynamic + isothermal runs. Different expressions for fitting the variation of the apparent activation energy and the pre-exponential function have been obtained and used to simulate the experimental results. The simulated results are compared with the experimental ones and with those simulated with the n-reaction order models. From the discussion carried out, it has been deduced that the Friedman method is valid when taking into account all the experimental data obtained in different operating conditions and after testing that the simulated results are close to the experimental ones.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

New Models Used to Determine the Dioxins Total Amount and Toxicity (TEQ) in Atmospheric Emissions from Thermal Processes

  • Palmer, Damià
  • Pou, Josep O.
  • González Sabaté, Lucinio
  • Díaz Ferrero, Jordi
  • Conesa, Juan A.
  • Ortuño García, Nuria
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
In order to reduce the calculation effort during the simulation of the emission of polychlorinated dibenzo-p-dioxins and furans (PCDD/F) during municipal solid waste incineration, minimizing the number of simulated components is mandatory. For this purpose, two new multilinear regression models capable of determining the dioxins total amount and toxicity of an atmospheric emission have been adjusted based on previously published ones. The new source of data used (almost 200 PCDD/F analyses) provides a wider range of application to the models, increasing also the diversity of the emission sources, from industrial and laboratory scale thermal processes. Only three of the 17 toxic congeners (1,2,3,6,7,8-HxCDD, 2,3,7,8-TCDF and OCDF), whose formation was found to be linearly independent, were necessary as inputs for the models. All model parameters have been statistically validated and their confidence intervals have been calculated using the Bootstrap method. The resulting coefficients of determination (R2) for the models are 0.9711 ± 0.0056 and 0.9583 ± 0.0085; its root mean square errors (RMSE) are 0.2115 and 0.2424, and its mean absolute errors (MAE) are 0.1541 and 0.1733 respectively.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Emissions of brominated compounds and polycyclic aromatic hydrocarbons during pyrolysis of E-waste debrominated in subcritical water

  • Soler, Aurora
  • Conesa, Juan A.
  • Ortuño García, Nuria
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Degradation of brominated flame retardants present in printed circuit boards (PCBs) was tested using subcritical water in a high pressure reactor. Debromination experiments were carried out in a batch stirred reactor at three different temperatures (225 °C, 250 °C and 275 °C) keeping a solid to liquid (S/L) ratio of PCB:water = 1:5 during 180 min. Results indicated that debromination efficiency was increased with temperature (18.5–63.6% of bromine present in the original PCB was removed). Thermal decomposition of the debrominated materials was studied and compared with that of the original PCB. Thermogravimetric analyses were performed at three different heating rates (5, 10 and 20 K min−1), studying both the pyrolysis (inert atmosphere) and combustion (in air). Pyrolysis runs of the debrominated materials were also performed in a quartz horizontal laboratory furnace at 850 °C, in order to study the emission of pollutants. More than 99% of the bromine was emitted in the form of HBr and Br2. Emissions of polycyclic aromatic hydrocarbons (PAHs) and bromophenols (BrPhs) decreased with the increase in the treatment temperature; naphthalene (10,800–18,300 mg kg−1 original sample) and monobrominated phenols (12.8–16.9 mg kg−1 original sample) were the most abundant compounds.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Microplastics in Spanish Table Salt

  • Iñiguez, María Esperanza
  • Conesa, Juan A.
  • Fullana, Andres
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Fullana, Andres|||/items/5a59481d-6a15-41b8-88c9-185b3877ea3a
Marine debris is widely recognized as a global environmental problem. One of its main components, microplastics, has been found in several sea salt samples from different countries, indicating that sea products are irremediably contaminated by microplastics. Previous studies show very confusing results, reporting amounts of microparticles (MPs) in salt ranging from zero to 680 MPs/kg, with no mention of the possible causes of such differences. Several errors in the experimental procedures used were found and are reported in the present work. Likewise, 21 different samples of commercial table salt from Spain have been analyzed for MPs content and nature. The samples comprise sea salts and well salts, before and after packing. The microplastic content found was of 50–280 MPs/kg salt, being polyethylene-terephthalate (PET) the most frequently found polymer, followed by polypropylene (PP) and polyethylene (PE), with no significant differences among all the samples. The results indicate that even though the micro-particles might originate from multiple sources, there is a background presence of microplastics in the environment.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Study of the Briquetting Process of Walnut Shells for Pyrolysis and Combustion

  • Font, Rafael
  • Villar, Estefanía
  • Garrido, María A.
  • Moreno Caballero, Ana Isabel
  • Gómez-Rico, María Francisca
  • Ortuño García, Nuria
  • Gómez-Rico, María Francisca|||/items/858ecde1-f676-4a71-982c-77a0fbb2c21c
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Walnut shells can be used as fuels in power plants directly or as biochars obtained by pyrolysis or torrefaction. They are an example of clean waste biomass which shows a low ash content and a high Net Calorific Value, making them excellent for energy recovery in industrial and non-industrial applications, such as in bakeries, restaurants, and homes. Their main inconvenience is their low bulk density. Densification is a possible solution that reduces the costs of transportation, handling, and storage. In this work, after the characterization of the walnut shells, briquettes were obtained using a hydraulic piston press briquette machine under different conditions to find the best quality without the need for previous grinding for pelletizing. This method features easy operation and maintenance, and the briquette shape could be adapted as desired. The quality of the briquettes was measured through their density and durability. After fixing a compaction pressure to obtain acceptable briquettes, the factors affecting their quality were studied: operating temperature, moisture content, and the presence of small amounts of walnuts. Good quality briquettes were obtained with a compaction pressure of 66 MPa, with densities around 1040 kg/m3, and durabilities higher than 94% when the process was carried at 140 °C. The greatest increase in durability was observed between briquettes obtained at room temperature and those obtained at 80 °C. The presence of small amounts of walnuts, common after the shelling process, improved the durability. Although water is necessary, briquettes obtained from biomass with only 1% of moisture showed better durabilities. Therefore, walnut shells are suitable for obtaining good quality briquettes according to the specifications of solid biofuels established in the standards, without the need for any pretreatment.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Fly ash reactivity modified by nitrogen and sulfur compounds

  • Soler, Aurora
  • Conesa, Juan A.
  • Ortuño García, Nuria
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
The inhibitory effect of thiourea (TUA), ammonium thiosulfate (TSA) and amidosulfonic acid (ASA) on the reactivity of fly ash air was investigated using a thermobalance at different heating rates (5, 10 and 20 K min-1). A model fly ash (activated carbon + 50 wt.% CuCl2·2H2O, pyrolyzed at 700 ºC and washed) was used as carbonaceous material. Adding CuCl2·2H2O to the activated carbon led to an increased rate of decomposition with the air’s oxygen. TUA and TSA behaved in a similar way, accelerating the decomposition of the model fly ash. ASA also accelerated the decomposition but to a lower extent. We proof that the increase in decomposition rate is caused by a reaction between carbonaceous material and N- and S-containing compounds. The formation of nitrogenated and sulphured compounds was confirmed by TG-MS. A kinetic model based on a single reaction of order 0.6 showed very good correlations with all the heating rates tested in oxidant atmosphere.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Pollution in the Marine Environment: Plastics, Microplastics and Organic Pollutants

  • Conesa, Juan A.
  • Iñiguez, María Esperanza
  • Fullana, Andres
  • Ortuño García, Nuria
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Fullana, Andres|||/items/5a59481d-6a15-41b8-88c9-185b3877ea3a
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Marine debris (MDs) produces a wide variety of negative environmental, economic, safety, health and cultural impacts, thus further research should focus on these kinds of waste. The present work has three main purposes: First, characterization of the MDs has been carried out in terms of their plastic composition, and their pollutant content (PAHs, ClBzs, ClPhs, BrPhs, PCDD/Fs and PCBs). Thermogravimetry has been used to identify the main constituents of the debris, using kinetic modelling to fit the proportion of each plastic. The decomposition of MDs is compared with that of their neat constituents, i.e. polyethylene (PE), polystyrene (PS), polypropylene (PP), nylon and polyethylen-tereftalate (PET). Furthermore, the analysis of pollutants in the samples reveal that MDs is not a highly contaminated waste. In addition, thermal decomposition of MD materials has been studied in a thermobalance at different atmospheres and heating rates. Second, a method for reusing the MDs is presented, consisting on the hydrothermal carbonization (HTC) of the wastes and the seawater where they are found. The plastics, once removed from the sea, cannot usually be recycled or reused. This debris has high net calorific value (NCV) what makes them suitable as a fuel. For this reason, a mixture of plastic materials was treated by HTC using seawater as a solvent, to examine the characteristics of the final products obtained and to test the feasibility of converting marine plastic debris to fuel. Results showed that an increase in the temperature of the process reduces the content of the inorganic anions and increases the NCV of the hydrochar (HTC char). The content of inorganic compounds in the HTC-liquor was measured, which increases as the process temperature rises. Organic compounds were also analyzed, being amides, alcohols and alkanes the major compounds in all cases. Finally, worried about the way in which these plastics reach the human being, microplastics where measured in sea products, more specifically in salt samples. In this sense, 21 different samples of commercial table salt from Spain have been analyzed for MP content and nature. The samples comprise sea salts and rock salts, before and after packing. Results indicate that even though the micro-particles might originate from multiple sources, there is a background presence of microplastics in the environment.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Volatile and semivolatile emissions from the pyrolysis of almond shell loaded with heavy metals

  • Martín-Lara, María Ángeles
  • Ortuño García, Nuria
  • Conesa, Juan A.
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Heavy metal-loaded almond shell was subjected to pyrolysis to understand the effect of the presence of different heavy metals on its thermal degradation. Pyrolysis behavior of native and metal-loaded samples was studied by thermogravimetric analysis. Similar shapes of thermogravimetric curves indicate that the presence of cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni) and lead (Pb) did not change the main degradation pathways of almond shell. However, the temperature at which the decomposition in each stage takes place at a higher rate and char yield was considerably modified by the presence of Cr and Ni. Then, pyrolysis tests of the almond shell samples were performed in a moving tubular reactor at 700 °C. Gases and volatile organic compounds were collected using Tedlar bags and semivolatile organic compounds were collected using a resin as adsorbent. Significant changes were obtained in the composition of the gaseous fraction as a result of the metal impregnation. The main changes in the composition of the gas were observed for Ni-loaded sample, which presented the highest H2 and CO yields. Also, the yields of most of the light hydrocarbons decrease in the presence of metal, while the rest remain quite similar. The total PAH yields reached 103 μg/g for nickel-loaded sample (Nisingle bondAS), 164 μg/g for copper-loaded sample (Cusingle bondAS), 172 μg/g for lead-loaded sample (Pbsingle bondAS), 245 μg/g for native sample (AS), 248 μg/g for cadmium-loaded sample (Cdsingle bondAS) and 283 μg/g for chromium-loaded sample (Crsingle bondAS). Nickel is the most effective in the higher aromatic tar reduction, followed by Cu and Pb, whereas the presence of Cd does not affect the total emissions of PAHs. Finally, the carcinogenic potency of the samples was calculated. Native sample and the sample loaded with Cr presented slightly higher values associated to the presence of small amounts of benzo(a)pyrene.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Effect of marine ambient in the production of pollutants from the pyrolysis and combustion of a mixture of plastic materials

  • Iñiguez, María Esperanza
  • Conesa, Juan A.
  • Soler, Aurora
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
A mixture of polyethylene (PE), polyethylene-terephtalate (PET), polypropylene (PP) and Nylon was submerged in marine water during 12 moths. The chlorine content of these plastics was measured through the passing time. Thermobalance was used to look for differences in the thermal decomposition of the plastics during in that time interval. Degradation of PET, PP and Nylon produced changes in the weight loss curve, but behaviour of PE is confusing. Pyrolysis and combustion at 850 °C was finally performed to get knowledge of the possible differences in the emission of main gases, volatiles and semivolatiles including polycyclic aromatic hydrocarbons (PAHs), polychlorinated benzenes (ClBzs), polychlorinated phenols (ClPhs), polybrominated phenols (BrPhs), polychlorinated biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Results show that the emission of chlorinated species is somewhat not affected by the chlorine content of the plastics mix. The production of PCBs and PCDD/Fs was very low, under 4 pg WHO-TEQ/g.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Application of Subcritical Water to Dechlorinate Polyvinyl Chloride Electric Wires

  • Soler, Aurora
  • Conesa, Juan A.
  • Ortuño García, Nuria
  • Conesa, Juan A.|||/items/05e6decf-7fcc-481c-a2db-3a3e67e75b5d
  • Ortuño García, Nuria|||/items/68c15f25-0107-4894-8ba6-f24e238c77f7
Polyvinyl chloride (PVC) electric wires were subjected to dechlorination in subcritical water at three different temperatures in a high-pressure reactor. About 2.09, 73.08, and 95.96 wt % of chlorine in PVC wires was removed during dechlorination at 200 °C, 250 °C, and 300 °C, respectively. The solid residues were analyzed and characterized by thermogravimetry, at three different heating rates (5 °C, 10 °C, and 20 °C/min) in inert and oxidizing atmosphere. With the purpose of studying the emission of chlorinated pollutants, pyrolysis experiments at 850 °C were also performed in a laboratory-scale reactor with the dechlorinated materials, as well as with the original PVC electric wire. Polycyclic aromatic hydrocarbons (PAH) formation increased, but chlorobenzenes (ClBz) and chlorophenols (ClPh) formation decreased as the temperature of dechlorination increased; naphthalene was the most abundant PAH and monochlorobenzene and monochlorinated phenols (3-+4-) were the most abundant chlorinated compounds.
DAU Arxiu Digital de la Universitat Ramon Llull
Publicación Artículo científico (JournalArticle)

Estimation of industrial emissions during pyrolysis and combustion of different wastes using laboratory data

  • Palmer Comas, Damià
  • Conesa, Juan A.
  • Ortuño, Núria
In our lab, we have been studying the emissions of different pollutants during pyrolysis and combustion of wastes under different conditions for the last three decades. These studies have focused on the effect of temperature and presence of oxygen on the production of different pollutants. Waste decomposition has been studied in a horizontal laboratory scale reactor, but no estimate has been made of the actual emissions in a conventional thermal decomposition system. In the present study, emissions during these wastes’ thermal decomposition were estimated using Aspen HYSYS. In the simulation software, the waste composition (elemental analysis) was given as an input parameter, as well as the gas flow rate used as atmosphere during the decomposition. The emitted hydrocarbons measured in the laboratory were equated to the emission of a single compound (propylene). The simulation permitted calculating the percentage of oxygen in the emitted gas, and the pollutant emissions were then recalculated under standard conditions. The emission of dioxins and furans were estimated under different conditions of decomposition, and an adequate approximation of the waste decomposition in actual incineration systems could be obtained.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Estimation of industrial emissions during pyrolysis and combustion of different wastes using laboratory data

  • Palmer Comas, Damià
  • Conesa, Juan A.
  • Ortuño, Núria
In our lab, we have been studying the emissions of different pollutants during pyrolysis and combustion of wastes under different conditions for the last three decades. These studies have focused on the effect of temperature and presence of oxygen on the production of different pollutants. Waste decomposition has been studied in a horizontal laboratory scale reactor, but no estimate has been made of the actual emissions in a conventional thermal decomposition system. In the present study, emissions during these wastes’ thermal decomposition were estimated using Aspen HYSYS. In the simulation software, the waste composition (elemental analysis) was given as an input parameter, as well as the gas flow rate used as atmosphere during the decomposition. The emitted hydrocarbons measured in the laboratory were equated to the emission of a single compound (propylene). The simulation permitted calculating the percentage of oxygen in the emitted gas, and the pollutant emissions were then recalculated under standard conditions. The emission of dioxins and furans were estimated under different conditions of decomposition, and an adequate approximation of the waste decomposition in actual incineration systems could be obtained.