Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Boundary condition and fuel composition effects on injection processes of high-pressure sprays at the microscopic level

  • Manin, J.
  • Bardi, M.
  • Pickett, L. M.
  • Payri, Raul|||0000-0001-7428-5510
Detailed imaging of n-dodecane and ethanol sprays injected in a constant-flow, high-pressure, high-temperature optically accessible chamber was per-formed. High-speed, diffused back-illuminated long-distance microscopy was used to resolve the spray structure in the near-nozzle field. The effect of injection and ambient pressures, as well as fuel temperature and composition have been studied through measurements of the spray penetration rates, hydraulic delays and spreading angles. Additional information such as transient flow velocities have been extracted from the measurements and compared to a control-volume spray model. The analysis demonstrated the influence of outlet flow on spray development with lower penetration velocities and wider spreading angles during the transients (start and end of injection) than during the quasi-steady period of the injection. The effect of fuel com-position on penetration was limited, while spreading angle measurements showed wider sprays for ethanol. In contrast, varying fuel temperature led to varying penetration velocities, while spreading angle remained constant during the quasi-steady period of the injection. Fuel temperature affected injector performance, with shorter delays as fuel temperature was increased. The comparisons between predicted and measured penetration rates showed differences suggesting that the transient behavior of the spreading angle of the sprays modified spray development significantly in the near-field. The reasonable agreement between predicted and measured flow velocity at and after the end of injection suggested that the complete mixing assumptions made by the model were valid in the near nozzle region during this period, when injected flow velocities are reduced., The authors wish to thank Chris Carlen from Sandia National Laboratories for designing and manufacturing specific ultra-fast LEDs, as well as Jose Enrique del Rey and Juan Pablo Viera from CMT-Motores Termicos for their support during the experiments. Support for the research carried out by Julien Manin at CMT-Motores Termicos was provided by the U.S. Department of Energy, Office of Vehicle Technologies. Sandia is a multi-program laboratory operated by Sandia Corporation, a Lockheed Martin Company for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Engine combustion network (ECN): measurements of nozzle geometry and hydraulic behavior

  • Kastengren, Alan L
  • Tilocco, F. Zak
  • Powell, Christopher F.
  • Manin, Julien
  • Pickett, Lyle
  • Bazyn, Tim
  • Payri, Raul|||0000-0001-7428-5510
[EN] Despite the importance of sprays to engine combustion, understanding has been hampered by the sensitivity of spray behavior to unknown nozzle geometry effects. The Engine Combustion Network (ECN) collaboration has focused on overcoming this impediment to spray research by focusing on a set of nominally identical diesel injectors. Detailed measurements of the nozzle geometry for the four ECN Spray A injectors (90 mu m diameter, axial single-hole nozzles) have been performed using x-ray tomography, x-ray phase-contrast imaging, silicone molding, and optical microscopy. Measurements of the needle motions (axial and lateral) and hydraulic performance of the nozzles have also been performed. Measurements of the nozzle geometry show that all of the nozzle holes are offset from the axis of the needle and sac. This offset creates an asymmetry in the inlet condition of the nozzle hole, which varies from nozzle to nozzle. The nozzle profile deviates significantly from the nominal specification, with an abrupt convergence of the nozzle holes near the nozzle exit seen in all of the injectors. Nozzle diameter measurements show a smaller diameter than the nominal specification, with significant differences between the injectors. Needle lift measurements show oscillatory behavior in both the axial and lateral motions of the needle. The hydraulic characterization of the nozzles demonstrates the impact of internal geometry (outlet diameter) on momentum and mass flow rate., The phase-contrast x-ray imaging was performed at the 32ID beamline of the Advanced Photon Source, Argonne National Laboratory. The work performed at Argonne and the use of the APS are supported by the U. S. Department of Energy under Contract No. DE-AC02-06CH11357 and by the Department of Energy Vehicle Technologies Program, with Gurpreet Singh as Team Leader. Sandia National Laboratories research was also supported by the U.S. Department of Energy Vehicle Technologies Program. Measurements were performed at the Combustion Research Facility in Livermore, California. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under Contract NoDE-AC04-94AL85000.