Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fundamental insights on ignition and combustion of natural gas in an active fueled pre-chamber spark-ignition system

  • Rajasegar, Rajavasanth
  • Niki, Yoichi
  • Li, Zheming
  • Musculus, Mark P.B.
  • García-Oliver, José M|||0000-0002-2676-9681
[EN] Pre-chamber spark-ignition (PCSI), either fueled or non-fueled, is a leading concept with the potential to enable diesel-like efficiency in medium-duty (MD) and heavy-duty (HD) natural gas (NG) engines. However, the inadequate scientific base and simulation tools to describe/predict the underlying processes governing PCSI systems is one of the key barriers to market penetration of PCSI for MD/HD NG engines. To this end, experiments were performed in a heavy-duty, optical, single-cylinder engine fitted with an active fueled PCSI module. The spatial and temporal progress of ignition and subsequent combustion of lean-burn natural gas using PCSI system were studied using optical diagnostic imaging and heat release analysis based on main-chamber and pre-chamber pressure measurements. Optical diagnostics involving simultaneous infrared (IR) and high-speed (30 kfps) broadband and filtered OH* chemiluminescence imaging are used to probe the combustion process. Following the early pressure rise in the pre-chamber, IR imaging reveals initial ejection of unburnt fuel-air mixture from the pre chamber into the main-chamber. Following this, the pre-chamber gas jets exhibit chemical activity in the vicinity of the pre-chamber region followed by a delayed spread in OH* chemiluminescence, as they continue to penetrate further into the main-chamber. The OH* signal progress radially until the pre-chamber jets merge, which sets up the limit to a first stage, jet-momentum driven, mixing-controlled (temperature field) premixed combustion. This is then followed by the subsequent deceleration of the pre-chamber jets, caused by the decrease in the driving pressure difference (AP) as well as charge entrainment, resulting in a flame front evolution, where mixing is not the only driver. Chemical-kinetic calculations probe the possibility of flame propagation or sequential auto-ignition in the second stage of combustion. Finally, key phenomenological features are then summarized so as to provide fundamental insights on the complex underlying fluid-mechanical and chemical-kinetic processes that govern the ignition and subsequent combustion of natural gas near lean-limits in high-efficiency lean-burn natural gas engines employing PCSI system., This research was sponsored by the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE) . Optical engine experiments were conducted at the Combustion Re-search Facility of Sandia National Laboratories in Livermore, CA. Sandia National Laboratories is a multi-mission laboratory man-aged and operated by National Technology and Engineering So-lutions of Sandia, LLC., a wholly owned subsidiary of Honey-well International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration (NNSA) under contract DE-NA0003525. We gratefully acknowledge the contributions of Keith Penney and Dave Cicone for their assistance in developing research tools and maintaining the optical engine. Jose M. Garcia-Oliver ac-knowledges the support of the Generalitat Valenciana government in Spain through Grant #Best/2019/176 during his scientific visit to the Combustion Research Facility.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of the mixing-limited hypothesis with first-principles simulation results

  • Schmidt, David P.
  • Arienti, Marco
  • García-Oliver, José M|||0000-0002-2676-9681
  • Pastor Enguídanos, José Manuel|||0000-0003-4458-0353
[EN] Starting with two well-tested, one-dimensional models of non-evaporating, mixing-limited sprays, governing equations for liquid mass and two-phase momentum for each model can be manipulated to reveal the formal similarity between momentum and liquid volume fraction. The consequence of this similarity is that momentum, when properly non-dimensionalized, is equal to the liquid volume fraction at any time and at any axial location within a non-evaporating, mixing-limited spray with a constant rate of injection. An alternative, the more well- known similarity between mass fraction and velocity, is also mathematically evident. We compare predictions of this mathematical analysis to high-fidelity, first-principles simulation results of a non-evaporating spray to assess the validity of the theoretical similarity. The analysis of the simulation not only confirms the mathematical derivations but also points to subtlety in the definition of the spray velocity. In particu- lar, the density-weighted velocity is required to observe similarity. The requirement of density-weighted velocity means that similarity tests require knowledge of both phase velocities. The agreement also works to confirm that the first-principles simulations are indeed mixing- limited, despite the finite nature of domain size and resolution., ACKNOWLEDGMENTS This study was supported by a grant from Sandia National Laboratories, a multi-mission laboratory managed and operated by National Technology and Engineering Solutions for Sandia LLC, a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration under Contract No. DE-NA0003525.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Cyclo-Pentane Impurities on the Autoignition Reactivity and Properties of a Gasoline Surrogate Fuel

  • Lopez Pintor, Dario
  • Abboud, Rami
  • MacDonald, James
  • Lee, Sanguk
[EN] Surrogate fuels that reproduce the characteristics of full-boiling range fuels are key tools to enable numerical simulations of fuel-related processes and ensure reproducibility of experiments by eliminating batch-to-batch variability. Within the PACE initiative, a surrogate fuel for regular-grade E10 (10%vol ethanol) gasoline representative of a U.S. market gasoline, termed PACE-20, was developed and adopted as baseline fuel for the consortium. Although extensive testing demonstrated that PACE-20 replicates the properties and combustion behavior of the full-boiling range gasoline, several concerns arose regarding the purity level required for the species that compose PACE-20. This is particularly important for cyclo-pentane, since commercial-grade cyclo-pentane typically shows 60%¿85% purity. In the present work, the effects of the purity level of cyclo-pentane on the properties and combustion characteristics of PACE-20 were studied. Chemical kinetic simulations were performed to predict the effects of cyclo-pentane impurities on the properties, octane rating, and autoignition reactivity under homogeneous charge compression-ignition conditions of PACE-20. From the numerical results, cyclo-pentane with 85% purity or higher is required to reasonably match both the research octane number and motor octane number of the target gasoline. Finally, homogeneous charge compression-ignition engine simulations show that impurities have only a modest effect on reactivity at naturally aspirated conditions, but cyclo-pentane purity is critical to properly replicate the pressure dependency of the reactivity., This work was performed at Sandia National Laboratories, Livermore, CA. Support was provided by the U.S. Department of Energy, Office of Vehicle Technologies. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy s National Nuclear Security Administration under contract DE-NA00035.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Internal and near nozzle measurements of Engine Combustion Network &quot, Spray G&quot, gasoline direct injectors

  • Duke, Daniel J.
  • Kastengren, Alan L.
  • Matusik, Katarzyna E.
  • Swantek, Andrew B.
  • Powell, Christopher F.
  • Vaquerizo, Daniel
  • Itani, Lama
  • Bruneaux, Gilles
  • Grover Jr., Ronald O.
  • Parrish, Scott
  • Markle, Lee
  • Schmidt, D.
  • Manin, Julien
  • Skeen, Scott A.
  • Pickett, L.M.
  • Payri, Raul|||0000-0001-7428-5510
[EN] Gasoline direct injection (GDI) sprays are complex multiphase flows. When compared to multi-hole diesel sprays, the plumes are closely spaced, and the sprays are more likely to interact. The effects of multi-jet interaction on entrainment and spray targeting can be influenced by small variations in the mass fluxes from the holes, which in turn depend on transients in the needle movement and small-scale details of the internal geometry. In this paper, we present a comprehensive overview of a multi-institutional effort to experimentally characterize the internal geometry and near-nozzle flow of the Engine Combustion Network (ECN) Spray G gasoline injector. In order to develop a complete pictitre of the near-nozzle flow, a standardized setup was shared between facilities. A wide range of techniques were employed, including both X-ray and visible-light diagnostics. The novel aspects of this work include both new experimental measurements, and a comparison of the results across different techniques and facilities. The breadth and depth of the data reveal phenomena which were not apparent from analysis of the individual data sets. We show that plume-to-plume variations in the mass fluxes from the holes can cause large-scale asymmetries in the entrainment field and spray structure. Both internal flow transients and small-scale geometric features can have an effect on the external flow. The sharp turning angle of the flow into the holes also causes an inward vectoring of the plumes relative to the hole drill angle, which increases with time due to entrainment of gas into a low-pressure region between the plumes. These factors increase the likelihood of spray collapse with longer injection durations., The X-ray experiments were performed at the 7-BM and 32-ID beam lines of the APS at Argonne National Laboratory. Use of the APS is supported by the U.S. Department of Energy (DOE) under Contract No. DE-AC02-06CH11357. Research was also performed at the Combustion Research Facility, Sandia National Laboratories, Livermore, California. Sandia National Laboratories is managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy National Nuclear Security Administration under contract DE-NA-0003525.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An experimental and one-dimensional modeling analysis of turbulent gas ejection in pre-chamber engines

  • García-Oliver, José M|||0000-0002-2676-9681
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Niki, Y.
  • Rajasegar, R.
  • Martínez-Hernándiz, Pablo José
  • Li, Z.
  • Musculus, M. P. B.
[EN] Experimental results from a study on the evolution of gas jets ejected through the orifices of a pre-chamber in a heavy-duty optical engine are presented. The work examines conditions without fuel inside the main-chamber, which helps to describe the dynamics of the ejected gas jets without the interference of subsequent combustion in the main-chamber. Experimental diagnostics consist of high-speed visible intensified imaging and low-speed infrared imaging. Additionally a one-dimensional gas jet model is used to characterize the spatial distribution of the ejected flow, including parameters such as tip penetration, which are then validated based on experimental results. Different stages in the ejection of pre-chamber jets are identified, with chemical activity restricted to a maximum distance of 5 to 10 orifice diameters downstream of the orifice as indicated by the recorded visible radiation. Sensitivity of cycle-to-cycle variations in pre-chamber jet development to the air-to-fuel ratio in the pre-chamber observed in the experiments is in most part attributed to the variations in the timing of combustion initiation in the pre-chamber. The influence of the ejection flow on the penetration of the gas jet on a cycle-tocycle basis is presented using the one-dimensional model. The one-dimensional model also indicates that the local flow exhibits highest sensitivity to operating conditions during the start of ejection until the timing when maximum flow is attained. Differences that exist during the decreasing mass-flow ejection time-period tend to smear out in part due to the transient slowdown of the ejection process, This research was sponsored by the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE). Optical engine experiments were conducted at the Combustion Research Facility, Sandia National Laboratories, Livermore, CA. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525. Jose M Garcia-Oliver acknowledges the support of the Generalitat Valenciana government in Spain through Grant Best/2019/176 for his scientific visit to the Combustion Research Facility. P. J. Martinez-Hernandiz is partly supported by an FPI contract (FPI-S2-19-21993) of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID05-19)" of the Universitat Politecnica de Valencia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Spatio-Temporal Progression of Two-Stage Autoignition for Diesel Sprays in a Low-Reactivity Ambient: n-Heptane Pilot-Ignited Premixed Natural Gas

  • Rajasegar, Rajavasanth
  • Niki, Yoichi
  • Li, Zheming
  • Musculus, Mark
  • García-Oliver, José M|||0000-0002-2676-9681
[EN] The spatial and temporal locations of autoignition depend on fuel chemistry and the temperature, pressure, and mixing trajectories in the fuel jets. Dual-fuel systems can provide insight into fuel-chemistry aspects through variation of the proportions of fuels with different reactivities, and engine operating condition variations can provide information on physical effects. In this context, the spatial and temporal progression of two-stage autoignition of a diesel-fuel surrogate, n-heptane, in a lean-premixed charge of synthetic natural gas (NG) and air is imaged in an optically accessible heavy-duty diesel engine. The lean-premixed charge of NG is prepared by fumigation upstream of the engine intake manifold. Optical diagnostics include: infrared (IR) imaging for quantifying both the in-cylinder NG concentration and the pilot-jet penetration rate and spreading angle, high-speed cool-flame chemiluminescence imaging as an indicator of low-temperature heat release (LTHR), and high-speed OH* chemiluminescence imaging as an indicator high-temperature heat release (HTHR). To aid interpretation of the experimental observations, zero-dimensional chemical kinetics simulations provide further understanding of the underlying interplay between the physical and chemical processes of mixing (pilot fuel-jet entrainment) and autoignition (two-stage ignition chemistry). Increasing the premixed NG concentration prolongs the ignition delay of the pilot fuel and increases the combustion duration. Due to the relatively short pilot-fuel injections utilized, the transient increase in entrainment near the end of injection (entrainment wave) plays an important role in mixing. To achieve desired combustion characteristics, i.e., ignition and combustion timing (e.g., for combustion phasing) and location (e.g., for reducing wall heat-transfer or tailoring charge stratification), injection parameters can be suitably selected to yield the necessary mixing trajectories that potentially help offset changes in fuel ignition chemistry, which could be a valuable tool for combustion design., This research was sponsored by the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE). Optical engine experiments were conducted at the Combustion Research Facility of Sandia National Laboratories in Livermore, CA. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration (NNSA) under contract DE-NA0003525. We gratefully acknowledge the contributions of Keith Penney and Dave Cicone for their assistance in developing research tools and maintaining the optical engine.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of operating conditions on soot-formation pathways in an optical direct-injection gasoline engine

  • Abboud, Rami
  • Singh, Eshan
  • López-Pintor, Darío
  • Sjöberg, Magnus
  • Payri, Raul|||0000-0001-7428-5510
  • López, J. Javier|||0000-0002-9486-2511
[EN] Understanding the dynamics of soot-formation pathways is crucial for the foreseeable advancement of gasoline engines, which depend on optimizing a complex array of parameters to meet regulatory standards. This paper employs a comprehensive set of parameter changes to examine the sources of soot formation observed in an optical direct-injection spark-ignition engine. By testing three injection pressures, three intake temperatures, five start of injection timings, and two engine loads, the study assesses their impact on soot formation and combustion characteristics. The analysis benefits from two distinct optical accesses, enabling a detailed portrayal of the flame morphology and the origins of sooting flames. Acquired images were supplemented by measured particle emissions, reinforcing the findings of the optical data. Transitioning from medium to high load led to an increase in particle emissions caused by a higher degree of injector tip wetting, as seen from the in-cylinder imaging. Increasing injection pressure reduced injector tip sooting, albeit leading to more spray-wall impingement at early injection timings. Under the earliest injection timing (-330 degrees CA), employing the lowest injection pressure (60 bar) reduced particle number and soot mass concentrations, with minimal impact on combustion performance. Intake temperature impacts fuel film quantity on both the injector tip and piston surface, with higher temperatures accelerating film evaporation from the bulk gas side. On the downside, it was necessary to retard combustion phasing at elevated intake temperatures to mitigate engine knock, consequently leading to a degradation in flame propagation speed and work output. The experiments also revealed a U-shaped trend in injection timing sweep, where spray-wall impingement dominates at the earliest timing, gas-phase in- homogeneities become more prominent at delayed timings, and injector tip soot is observed under all conditions due to injector fouling. The results of this study illuminate potential strategies for reducing engine-out particle emissions while maintaining satisfactory combustion performance, aiming to possibly obviate the necessity for gasoline particle filters., PhD student Rami Abboud has received funding through a mobility grant (Ref: FPU19/03838) from the Spanish Ministry of Science, Innovation, and Universities to support his research visit at Sandia National Laboratories. The authors would like to thank Dan Pierce and Kyra Schmidt for their dedicated support of the Sandia Light-Duty DISI Engine Laboratory. This work was performed at the Applied Combustion Research Department, Combustion Research Facility, Sandia National Laboratories, Livermore, CA. This Article has been authored by National Technology and Engineering Solutions of Sandia, LLC. under contract No. DE-NA0003525 with the U.S. Department of Energy/National Nuclear Security Administration. The United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes. The views expressed in the article do not necessarily represent the views of the U.S. Department of Energy or the United States Government.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Verification of diesel spray ignition phenomenon in dual-fuel diesel-piloted premixed natural gas engine

  • Niki, Yoichi
  • Rajasegar, Rajavasanth
  • Li, Zheming
  • Musculus, Mark P.B.
  • Takasaki, Koji
  • García-Oliver, José M|||0000-0002-2676-9681
[EN] Dual-fuel (DF) engines, in which premixed natural gas and air in an open-type combustion chamber is ignited by diesel-fuel pilot sprays, have been more popular for marine use than pre-chamber spark ignition (PCSI) engines because of their superior durability. However, control of ignition and combustion in DF engines is more difficult than in PCSI engines. In this context, this study focuses on the ignition stability of n-heptane pilot-fuel jets injected into a compressed premixed charge of natural gas and air at low-load conditions. To aid understanding of the experimental data, chemical-kinetics simulations were carried out in a simplified engine-environment that provided insight into the chemical effects of methane (CH4) on pilot-fuel ignition. The simulations reveal that CH4 has an effect on both stages of n-heptane autoignition: the small, first-stage, cool-flame-type, low-temperature ignition (LTI) and the larger, second-stage, high-temperature ignition (HTI). As the ratio of pilot-fuel to CH4 entrained into the spray decreases, the initial oxidization of CH4 consumes the OH radicals produced by pilot-fuel decomposition during LTI, thereby inhibiting its progression to HTI. Using imaging diagnostics, the spatial and temporal progression of LTI and HTI in DF combustion are measured in a heavy-duty optical engine, and the imaging data are analyzed to understand the cause of severe fluctuations in ignition timing and combustion completeness at low-load conditions. Images of cool-flame and hydroxyl radical (OH*) chemiluminescence serve as indicators of LTI and HTI, respectively. The cycle-to-cycle and spatial variation in ignition extracted from the imaging data are used as key metrics of comparison. The imaging data indicate that the local concentration of the pilot-fuel and the richness of the surrounding natural-gas air mixture are important for LTI and HTI, but in different ways. In particular, higher injection pressures and shorter injection durations increase the mixing rate, leading to lower concentrations of pilot-fuel more quickly, which can inhibit HTI even as LTI remains relatively robust. Decreasing the injection pressure from 80 MPa to 40 MPa and increasing the injection duration from 500 mu s to 760 mu s maintained constant pilot-fuel mass, while promoting robust transition from LTI to HTI by effectively slowing the mixing rate. This allows enough residence time for the OH radicals, produced by the two-stage ignition chemistry of the pilot-fuel, to accelerate the transition from LTI to HTI before being consumed by CH4 oxidation. Thus from a practical perspective, for a premixed natural gas fuel-air equivalence-ratio, it is possible to improve the "stability" of the combustion process by solely manipulating the pilot-fuel injection parameters while maintaining constant mass of injected pilot-fuel. This allows for tailoring mixing trajectories to offset changes in fuel ignition chemistry, so as to promote a robust transition from LTI to HTI by changing the balance between the local concentration of the pilot-fuel and richness of the premixed natural gas and air. This could prove to be a valuable tool for combustion design to improve fuel efficiency or reduce noise or perhaps even reduce heat-transfer losses by locating early combustion away from in-cylinder walls., This research was sponsored in part by the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE). Optical engine experiments were conducted at the Combustion Research Facility of Sandia National Laboratories in Livermore, CA. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration (NNSA) under contract DE-NA0003525.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Dibutyl Ether - Methanol Blend Ratios on Deflagration-Based and Autoignition-Based Knock in Spark-Ignition Engines

  • Singh, Eshan
  • Abboud, Rami
  • Strickland, Tyler
  • Kim, Namho
  • López Pintor, Darío
  • Sjöberg, Magnus
[EN] Methanol is an attractive fuel that can be produced using renewable sources. However, its low reactivity may present challenges to combustion modes (like Spark-Assisted Compression Ignition) that rely on autoignition. To tweak its reactivity, a highly reactive bio-derived molecule, dibutyl ether (DBE), was blended in varying volume percentages (from 0 to 40% v/v). Experiments were conducted for a) lean operation with air-fuel ratio lambda = 2, b) stoichiometric steady-state operation, and c) stoichiometric transient-state operation. For lean operation, adding increasing fractions of DBE increased the reactivity, as evidenced by a retarded knock-limited combustion phasing. For stoichiometric steady operation, the addition of DBE had very little impact on the knock limits at lower blends up to 20% v/v. A unique knock phenomenon, hereby termed as deflagration-based knock, was observed for these blends, wherein pressure oscillations were observed as the flame-front progressed, without autoignition. The knock mode shifted to conventional end-gas autoignitionbased knock for 30% and 40% DBE blends. For stoichiometric transient conditions, marked by cooler operation, all DBE blends showed only deflagration-based knock. Spectral analysis of the deflagration-based knock suggests higher contribution from the 10-15 kHz range, corresponding to second-mode harmonics. Computational studies conducted to match the stoichiometric operating condition showed similar pressure oscillations. Analysis of the simulated results imply that deflagrationbased knock occurs when the flame reacts to the pressure disturbances such that a feedback loop increases the pressure oscillations in each flame-front passage. The findings of this study highlight the physics behind deflagration-based knock, as observed in DBE-methanol blends, and are critical to other renewable fuels such as ethanol and hydrogen. Novelty and Significance: The manuscript uses fully renewable blends of dibutyl ether and methanol for sparkassisted compression ignition with lean fuel-air mixture, and for conventional stoichiometric spark-ignition combustion. For stoichiometric operation, the authors observe a unique phenomenon where pressure oscillations start right after the spark timing, and increases as flame-front moves forward, hereby termed as deflagration-based-knock. This novel phenomenon is explained on the basis of pressure-dependent reactivity, which provides a feedback mechanism to the pressure oscillations. According to the authors, the observations are significant to fast-burning fuels (or more generally, fast combustion), and observations have been recorded elsewhere for ethanol (by authors) and hydrogen (elsewhere). To the best of our knowledge, this is the first investigation of deflagration-based-knock in small-bore engines, or in conventional spark-ignition combustion. Authors suggest that depending on the operating conditions, deflagration-based-knock may form a bottleneck to engines operating on such renewable fuels. Moreover, conventional knock mitigation mechanism, like retarding spark timing, may not be effective against the novel deflagration-based-knock., Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of San-dia, LLC (NTESS) , a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy's National Nuclear Security Administration (DOE/NNSA) under contract DE-NA0003525. This written work is authored by an employee of NTESS. The employee, not NTESS, owns the right, title and interest in and to the written work and is responsible for its contents. Any subjective views or opinions that might be expressed in the written work do not necessarily represent the views of the U.S. Government. The publisher acknowledges that the U.S. Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this written work or allow others to do so, for U.S. Government purposes. The DOE will provide public access to results of federally sponsored research in accordance with the DOE Public Access Plan.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of pilot-fuel mixing on the spatio-temporal progression of two-stage autoignition of diesel-sprays in low-reactivity ambient fuel-air mixture

  • Rajasegar, Rajavasanth
  • Niki, Yoichi
  • Li, Zheming
  • Musculus, Mark P. B.
  • García-Oliver, José M|||0000-0002-2676-9681
[EN] The spatial and temporal locations of autoignition for direct-injection compression-ignition engines depend on fuel chemistry, temperature, pressure, and mixing trajectories in the fuel jets. Dual-fuel systems can provide insight into both fuel-chemistry and physical effects by varying fuel reactivities and engine operating conditions. In this context, the spatial and temporal progression of two-stage autoignition of a diesel-fuel surrogate, n-heptane, in a lean-premixed charge of synthetic natural-gas (NG) and air is imaged in an optically accessible heavy-duty diesel engine. The lean-premixed charge of NG is prepared by fumigation upstream of the engine intake manifold. Optical diagnostics include high-speed (15kfps) cool-flame chemiluminescenceimaging as an indicator of low-temperature heat-release (LTHR) and OH * chemiluminescence-imaging as an indicator high-temperature heat-release (HTHR). NG prolongs the ignition delay of the pilot fuel and increases the combustion duration. Zero-dimensional chemical-kinetics simulations provide further understanding by replicating a Lagrangian perspective for mixtures evolving along streamlines originating either at the fuel nozzle or in the ambient gas, for which the pilot-fuel concentration is either decreasing or increasing, respectively. The zero-dimensional simulations predict that LTHR initiates most likely on the air streamlines before transitioning to HTHR, either on fuel-streamlines or on air-streamlines in regions of near-constant phi. Due to the relatively short pilot-fuel injection-durations, the transient increase in entrainment near the end of injection (entrainment wave) is important for quickly creating auto-ignitable mixtures. To achieve desired combustion characteristics, e.g., multiple ignition-kernels and favorable combustion phasing and location (e.g., for reducing wall heat-transfer or optimizing charge stratification), adjusting injection parameters could tailor mixing trajectories to offset changes in fuel ignition chemistry. (C) 2020 The Combustion Institute. Published by Elsevier Inc. All rights reserved., Support for this research at the Combustion Research Facility, Sandia National Laboratories, Livermore, CA, was provided by the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy. Sandia is a multi-mission laboratory operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. DOE's National Nuclear Security Administration under contract DE-NA0003525
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fuel Effects on Aviation Engine Emissions: A Chemical Reactor Network Modeling Study

  • López-Pintor, Darío
  • MacDonald, James
  • Leyland, Pénélope
  • Ramírez-Correa, Elkin Josue
  • García-Oliver, José M|||0000-0002-2676-9681
  • Payri, Raul|||0000-0001-7428-5510
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
[EN] The present study investigates the formulation of surrogates for Jet-A and sustainable aviation fuel (SAF) by means of a chemical reactor network (CRN) to predict emissions in gas-turbine combustors. The modeling framework is used to analyze the effects of fuel composition, specifically the replacement of Jet-A with SAF as well as the substitution of aromatics in Jet-A with cycloalkanes. This approach enables the examination of the effects of the fuel class and molecular structure independently of global exhaust emission trends. A comprehensive chemical kinetic mechanism incorporating 8478 species and 33,318 reactions was used to model jet fuel surrogates. This mechanism, validated against ignition delay times, laminar flame speeds, and extinction strain rates, accurately predicted combustion characteristics for iso-cetane and iso-dodecane, key components of SAF. Surrogate fuels for Jet-A and alternative fuels were formulated targeting critical properties such as density and cetane number. Surrogate simulation results show strong alignment with experimental data on ignition delay and flame speed, further confirming the reliability of the surrogates. The CRN model was developed using the CFM56 engine data and validated against the International Civil Aviation Organization emission benchmarks. After that, two different fuel replacement scenarios, involving Jet-A, are investigated. In the first one, Jet-A is compared to 100% SAF, which helps assess expected differences in combustion performance if a fully renewable fueling supply is followed. Results show that NO x emissions are unaffected by SAF, aligning with previous experimental studies. Polycyclic aromatic hydrocarbons (PAH) decrease by 93% for SAF compared to Jet-A, while Jet-A produces more CO due to its aromatic content. Substituting aromatics with cycloalkanes in Jet-A reduces PAH emissions by up to 96 or 92%, depending on whether all aromatics are replaced or only diaromatics. In a second scenario, aromatics are removed from conventional Jet-A and replaced with cycloalkane species, which can still hold the swelling properties needed by the fueling system. In terms of combustion, cycloalkane substitution leads to slightly increased CO emissions and reduced flame temperatures. These results demonstrate the potential of SAFs and cycloalkanes in reducing soot precursors while maintaining a highly similar performance in the combustion process. Overall, the proposed CRN framework provides a good example of how a predictive and computationally efficient tool can help in the early evaluation of alternative aviation fuels under realistic gas-turbine combustor conditions., This work has been partially funded by the EU Horizon 2020 Research and Innovation program by means of SENECA (LTO Noise and Emissions of Supersonic Aircraft) project, grant no. 101006742, as well as by the DIALOGUE project (CIPROM/2022/24) from the Generalitat Valenciana, in Spain. This work was partially performed at the Combustion Research Facility at Sandia National Laboratories, Livermore, CA. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC (NTESS), a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy s National Nuclear Security Administration (DOE/ NNSA) under contract DE-NA0003525. Funding for open access charge: CRUE-Universitat Politecnica de Valencia.