Pasar al contenido principal

MODELADO CINEMATICO Y DINAMICO DEL MOVIMIENTO DE LOS TEJIDOS BLANDOS. APLICACION AL DISEÑO DE MODELOS BIOMECANICOS (DESARROLLO E IMPLEMENTACION DE MODELOS)

DPI2009-13830-C02-01

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2009
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Model of Soft Tissue Artifact Propagation to Joint Angles in Human Movement Analysis

  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
  • De Rosario Martínez, Helios
[EN] This work describes the kinematic laws that govern the transmission of soft tissue artifact errors to kinematic variables in the analysis of human movements. Artifacts are described as relative translations and rotations of the marker cluster over the bone, and a set of explicit expressions is defined to account for the effect of that relative motion on different representations of rotations: the rotation around the screw axis, or rotation vector, and three Euler angle sequences (XY0Z, YX0Y00, ZX0 Y00). Although the error transmission is nonlinear in all cases, the effect of artifacts is greater on Euler sequences than on the rotation vector. Specifically, there are crosstalk effects in Euler sequences that amplify the errors near singular configurations. This fact is an additional source of variability in studies that describe artifacts by comparing the Euler angles obtained from skin markers, with the angles of an artifact-free gold standard. The transmission of errors to rotation vector coordinates is less variable or dependent on the type of motion. This model has been tested in an experiment with a deformable mechanical model with a spherical joint., This work has been funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2009-13830-C02-01 and DPI2009-13830-C02-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Kinematic description of soft tissue artifacts: quantifying rigid versus deformation components and their relation with bone motion

  • De Rosario Martínez, Helios
  • Conejero Navarro, Efrain
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
  • Mata Amela, Vicente|||0000-0003-2255-0567
[EN] This paper proposes a kinematic approach for describing soft tissue artifacts (STA) in human movement analysis. Artifacts are represented as the field of relative displacements of markers with respect to the bone. This field has two components: deformation component (symmetric field) and rigid motion (skew-symmetric field). Only the skew-symmetric component propagates as an error to the joint variables, whereas the deformation component is filtered in the kinematic analysis process. Finally, a simple technique is proposed for analyzing the sources of variability to determine which part of the artifact may be modeled as an effect of the motion, and which part is due to other sources. This method has been applied to the analysis of the shank movement induced by vertical vibration in 10 subjects. The results show that the cluster deformation is very small with respect to the rigid component. Moreover, both components show a strong relationship with the movement of the tibia. These results suggest that artifacts can be modeled effectively as a systematic relative rigid movement of the marker cluster with respect to the underlying bone. This may be useful for assessing the potential effectiveness of the usual strategies for compensating for STA. © 2012 International Federation for Medical and Biological Engineering., This work has been funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2009-13830-C02-01, DPI2009-13830-C02-02 and IMPIVA IMDEEA/2012/79 and IMDEEA/2012/80).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Implementacion basada en el middleware OROCOS de controladores dinamicos pasivos para un robot paralelo, Dynamic controllers implementation based on the OROCOS middleware.

  • Vallés Miquel, Marina|||0000-0002-6396-0098
  • Valera Fernández, Ángel|||0000-0001-6843-6394
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Cazalilla Morenas, Jose Ignacio
[EN] Automatic control of robotic systems nowadays deals more and more with the implementation of different tasks to be achieved by the robot with distinct complexity degree, periodic or aperiodic, with local execution or distributed along a communication network and needing to deal with different kinds of hardware. Deal with the controller implementation for a new robotic platform involved to develop suitable software again for the new hardware or, in the best case, to adapt the existing one. In the recent years it has been tending to a component-based programing that allows to develop reusable software and to use a middleware that make it possible to abstract the developed software from the used hardware and from the available communication protocols. At this paper one of these middleware has been used, specially oriented to robotics as is OROCOS. Using the Orocos Toolchain library the real-time components needed for the implementation of several dynamic controllers for a parallel manipulator have been developed. At this paper the robot and the designed controllers are described and the results over the actual robot are shown., [ES] La complejidad actual de los sistemas robotizados y de las aplicaciones que éstos deben realizar requiere que los robots dispongan de un control automático que permita la ejecución de las distintas tareas que forman parte del algoritmo de control y que tenga en cuenta cuestiones relacionadas por ejemplo con la periodicidad, el modo de ejecución, el hardware que se utilizará, etc. Para el desarrollo de este tipo de aplicaciones de control en los últimos añ os se tiende a la programación basada en componentes puesto que ésta permite obtener código reusable. Así mismo también se está incrementando la utilización de middlewares que permiten la abstracción de los sistemas operativos, el soporte de tiempo real y la infraestructura de comunicaciones. En el presente artículo se propone la utilización de un middleware orientado especialmente a la robótica: OROCOS. Así se describe cómo haciendo uso de una de sus librerías, Orocos Toolchain, se han desarrollado una serie de componentes correspondientes a distintos algoritmos para el control dinámico de robots, aplicándose a un robot paralelo de 3 grados de libertad (DOF)., Los autores desean expresar su agradecimiento al Ministerio de Ciencia e Innovacion de Espa ´ na por la financiaci ˜ on´ parcial de este trabajo bajo los proyectos (FEDER/CICYT) de investigacion DPI2009-13830-C02-01 y DPI2010-20814-C02- ´ (01, 02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Propagation of Artifact Errors on Kinematic Variables. Effect on Euler Angles

  • De Rosario Martínez, Helios
  • Moreno Cano, Rafael
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
This work has been funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2009-13830-C02-01, DPI2009-13830- C02-02 and IMPIVA IMIDIC/2010/84)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A methodology for dynamic parameters identification of 3-DOF parallel robots in terms of relevant parameters

  • Díaz-Rodríguez, Miguel Ángel|||0000-0001-7243-4957
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Valera Fernández, Ángel|||0000-0001-6843-6394
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
[EN] The identification of the dynamic parameters in mechanical systems is important for improving model-based control and performing realistic dynamic simulations. Generally, when identification techniques are applied, only a subset of parameters so-called base parameters can be identified. Moreover, some of these parameters cannot be properly identified if they make a small contribution to the robot dynamics. In this paper, a strategy for dynamic parameter identification of parallel robots in terms of relevant parameters is put forward. The proposed methodology starts from a dynamic model developed by means of the Gibbs-Appell equations. Afterwards, the model is simplified based on the considered geometry of each link and symmetry of the legs. The identification is done by Weighted Least Squares. With statistical considerations, the number of model parameters is reduced until the physical feasibility conditions are met. The strategy has been experimentally tested on two actual 3-DOF parallel robots. The response of the inverse and forward dynamics problem using the identified parameters agrees with experiments. (C) 2010 Elsevier Ltd. All rights reserved., This research has been supported by the Spanish Government Grant DPI2009-13830-C02-01.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mechatronic development and dynamic control of a 3-DOF parallel manipulator

  • Vallés Miquel, Marina|||0000-0002-6396-0098
  • Valera Fernández, Ángel|||0000-0001-6843-6394
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Díaz-Rodríguez, Miguel
The aim of this article is to develop, from the mechatronic point of view, a low-cost parallel manipulator (PM) with 3-degrees of freedom (DOF). The robot has to be able to generate and control one translational motion (heave) and two rotary motions (rolling and pitching). Applications for this kind of parallel manipulator can be found at least in driving-motion simulation and in the biomechanical field. An open control architecture has been developed for this manipulator, which allows implementing and testing different dynamic control schemes for a PM with 3-DOF. Thus, the robot developed can be used as a test bench where control schemes can be tested. In this article, several control schemes are proposed and the tracking control responses are compared. The schemes considered are based on passivity-based control and inverse dynamic control. The control algorithm considers point-to-point control or tracking control. When the controller considers the system dynamics, an identified model has been used. The control schemes have been tested on a virtual robot and on the actual prototype. © 2012 Taylor & Francis Group, LLC., The authors wish to express their gratitude to the Plan Nacional de I+D, Comision Interministerial de Ciencia y Tecnologia (FEDER-CICYT) for the partial financing of this study under the projects DPI2009-13830-C02-01 and DPI2010-20814-C02-(01, 02). This work was also supported in part by the CDCHT-ULA Grant I-1286-11-02-B.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Representation of planar motion of complex joints by means of rolling pairs. Application to neck motion

  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • De Rosario Martínez, Helios
  • Galvez Griso, Jose Antonio
[EN] We propose to model planar movements between two human segments by means of rolling-without-slipping kinematic pairs. We compute the path traced by the instantaneous center of rotation (ICR) as seen from the proximal and distal segments, thus obtaining the fixed and moving centrodes, respectively. The joint motion is then represented by the rolling-without-slipping of one centrode on the other. The resulting joint kinematic model is based on the real movement and accounts for nonfixed axes of rotation; therefore it could improve current models based on revolute pairs in those cases where joint movement implies displacement of the ICR. Previous authors have used the ICR to characterize human joint motion, but they only considered the fixed centrode. Such an approach is not adequate for reproducing motion because the fixed centrode by itself does not convey information about body position. The combination of the fixed and moving centrodes gathers the kinematic information needed to reproduce the position and velocities of moving bodies. To illustrate our method, we applied it to the flexion-extension movement of the head relative to the thorax. The model provides a good estimation of motion both for position variables (mean R pos=0.995) and for velocities (mean R vel=0.958). This approach is more realistic than other models of neck motion based on revolute pairs, such as the dual-pivot model. The geometry of the centrodes can provide some information about the nature of the movement. For instance, the ascending and descending curves of the fixed centrode suggest a sequential movement of the cervical vertebrae. © 2010 Elsevier Ltd., This work was funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2006-14722-C02-01, DPI2006-14722-C02-02, DPI2009-13830-C02-01, DPI2009-13830-C02-02 and Ramon y Cajal contract to JAG).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Aplicación de la arquitectura orientada a servicios universal plug-and-play para facilitar la integración de robots industriales en lineas de producción

  • Valera Fernández, Ángel|||0000-0001-6843-6394
  • Sánchez Salmerón, Antonio José|||0000-0003-1896-5356
  • Ricolfe Viala, Carlos|||0000-0002-2980-4569
  • Mellado, Martin|||0000-0002-3429-5316
  • Juste López, Daniel
  • Olmos Zaragozá, Eduardo
[EN] La integración de equipamiento y dispositivos en células robotizadas industriales con tecnologías de interfaz de Ethernet y dispositivos de bajo coste como sistemas de visión, cámaras láser, sensores de fuerza, autómatas programables, PDAs, etc. permite el desarrollo de soluciones potentes e inteligentes. Sin embargo, la programación eficiente de todos estos dispositivos requieren conocimientos muy específicos sobre estos equipos, sus arquitecturas hardware, lenguajes de programación dedicados y detalles sobre protocolos de bajo nivel de comunicación de sistemas. El artículo describe y utiliza una de las arquitecturas orientadas a servicios más interesante y que mejor se adapta a las células robotizadas: la arquitectura Universal Plug-and-Play. Utilizando esta arquitectura en el artículo se ha desarrollado un banco de pruebas basado en dos robots industriales. Los resultados obtenidos muestran claramente que la utilización de esquemas integrados basados en arquitecturas SOA reduce los tiempos de integración, adaptándose muy bien a la integración de células robotizadas industriales., Los autores desean expresar su agradecimiento al Plan Nacional de I+D, Comisión Interministerial de Ciencia y Tecnología (FEDER-CICYT) por la financiación parcial de este trabajo bajo los proyectos de investigación DPI2009-13830-C02-01 y DPI2010-20814-C02-02
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Propagation of soft tissue artifacts to the center of rotation: A model for the correction of functional calibration techniques

  • De Rosario Martínez, Helios
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
  • Valera Fernández, Ángel|||0000-0001-6843-6394
This paper presents a mathematical model for the propagation of errors in body segment kinematics to the location of the center of rotation. Three functional calibration techniques, usually employed for the gleno-humeral joint, are studied: the methods based on the pivot of the instantaneous helical axis (PIHA) or the finite helical axis (PFHA), and the ¿symmetrical center of rotation estimation¿ (SCoRE). A procedure for correcting the effect of soft tissue artifacts is also proposed, based on the equations of those techniques and a model of the artifact, like the one that can be obtained by double calibration. An experiment with a mechanical analog was performed to validate the procedure and compare the performance of each technique. The raw error (between 57 and 68 mm) was reduced by a proportion of between 1:6 and less than 1:15, depending on the artifact model and the mathematical method. The best corrections were obtained by the SCoRE method. Some recommendations about the experimental setup for functional calibration techniques and the choice of a mathematical method are derived from theoretical considerations about the formulas and the results of the experiment., This work has been funded by the Spanish Government (Grants DPI2009-13830-C02-01, DPI2009-13830-C02-02, DPI2010-20814-C02-01, and DPI2010-20814-C02-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A car-seat example of automated anthropomorphic testing of fabrics using force-controlled robot motions

  • Valera Fernández, Ángel|||0000-0001-6843-6394
  • Benimeli, Francesc|||0000-0001-8565-5548
  • Zotovic Stanisic, Ranko|||0000-0002-4746-2101
  • Mellado, Martin|||0000-0002-3429-5316
  • Solaz Sanahuja, José Salvador
  • De Rosario Martínez, Helios
  • Robertsson, Anders
  • Nilsson ., Klass
For the last years, automation is widely used to relieve humans from repetitive tasks, primarily and firstly within manufacturing. However, for products with less ideal (or hard to model) properties, and when forces depends on human interaction, automated testing has not been explored until now. This work presents the analysis of the (human-dependent) motions/forces based on a fully implemented test case for car-seat testing. For emulation of the corresponding mechanical wear, an experimental test bench was developed. A sensor mat with a pressure gauge net was used in the test bench to determine the relevant loads, and the corresponding movements performed by the humans when sitting in a car seat were acquired by means of a photogrammetry system. Finally, to automate the reproduction of such movements by means of a dummy held by a robot, several controllers have been developed to regulate the force applied by the dummy on the seat. Simplicity and force-control performance for the human replication was also investigated in this work, showing the benefit of freely programmable (open) force control. The developed system has many practical applications, as allowing the analysis of the wearing caused by these movements on the seat upholstery. Thus, force controlled testing of fabrics using robots is a viable option. © 2010 IEEE., This work was supported in part by the Plan Nacional de I+D, Comision Interministerial de Ciencia y Tecnologia (FEDER-CICYT) under the projects DPI2009-13830-C02-01 and DPI2010-20814-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modelado y Resolución del Problema Dinámico Inverso y Directo en Tiempo Real de Robots Industriales, Robot Modeling and Dynamic Parameter Identificacion. Inverse Dynamic Problem Resolution in Real Time

  • Rosillo, N.
  • Valero Chuliá, Francisco José
  • Valera Fernández, Ángel|||0000-0001-6843-6394
  • Benimeli, Francesc|||0000-0001-8565-5548
  • Mata Amela, Vicente|||0000-0003-2255-0567
[ES] Este trabajo presenta el desarrollo y la validación de una metodología que permite el modelado y la identificación de los parámetros dinámicos de robots manipuladores. La ecuación dinámica del robot está basada en la ecuación de movimiento de Gibbs-Appell, proporcionando un conjunto de ecuaciones bien estructuradas que pueden ser calculadas en tiempo real. Además, se puede expandir fácilmente el modelo dinámico, lo que permite incluir en éste por ejemplo el efecto de la dinámica de los actuadores y el fenómeno de la fricción. El artículo propone dos métodos para la identificación del modelado dinámico de robots, estos procedimientos han sido aplicados a un robot industrial PUMA 560 equipado con una arquitectura abierta de control basada en un computador personal industrial. Finalmente se han construido las ecuaciones de la dinámica inversa a partir de los parámetros dinámicos identificados y han sido implementadas en tiempo real., [EN] This work presents the development and validation of a methodology allowing dynamic parameter identification in robotic manipulators. The dynamic equations of the robot are based on the Gibbs-Appell equations of motion, yielding well structured equations which can be computed in real time and make the model easily expandable, which allows to include the actuator dynamic effect and the friction phenomenon. This paper also deals with dynamic modeling identification in robotic manipulators. Two different methods are proposed and validated on an industrial robotic system: a PUMA 560 provided with an open control architecture based on an industrial personal computer. Finally, using the dynamic parameters identified, the inverse dynamic equations have been obtained and implemented in real time., Los autores desean expresar su agradecimiento al Plan Nacional de I+D, Comisión Interministerial de Ciencia y Tecnología (FEDER-CICYT) por la financiación parcial de este trabajo bajo los proyectos DPI2008-06737-C02-01 y DPI2009-13830-C02-01.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Point of optimal kinematic error: Improvement of the instantaneous helical pivot method for locating centers of rotation

  • De Rosario Martínez, Helios
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
[EN] This paper proposes a variation of the instantaneous helical pivot technique for locating centers of rotation. The point of optimal kinematic error (POKE), which minimizes the velocity at the center of rotation, may be obtained by just adding a weighting factor equal to the square of angular velocity in Woltring's equation of the pivot of instantaneous helical axes (PIHA). Calculations are simplified with respect to the original method, since it is not necessary to make explicit calculations of the helical axis, and the effect of accidental errors is reduced. The improved performance of this method was validated by simulations based on a functional calibration task for the gleno-humeral joint center. Noisy data caused a systematic dislocation of the calculated center of rotation towards the center of the arm marker cluster. This error in PIHA could even exceed the effect of soft tissue artifacts associated to small and medium deformations, but it was successfully reduced by the POKE estimation., This work has been funded by the Spanish Government (Grants DPI2009-13830-C02-01, DPI2009-13830-CO2-02, DPI2010-20814-CO2-01, DPI2010-20814-CO2-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Adjusting the parameters of the mechanical impedance for velocity, impact and force control

  • Zotovic Stanisic, Ranko|||0000-0002-4746-2101
  • Valera Fernández, Ángel|||0000-0001-6843-6394
This work is dedicated to the analysis of the application of active impedance control for the realisation of three objectives simultaneously: velocity regulation in free motion, impact attenuation and finally force tracking. At first, a brief analysis of active impedance control is made, deducing the value of each parameter in order to achieve the three objectives. It is demonstrated that the system may be made overdamped with the adequate selection of the parameters if the characteristics of the environment are known, avoiding high overshoots of force during the impact. The second and most important contribution of this work is an additional measure for impact control in the case when the characteristics of the environment are unknown. It consists in switching among different values of the parameters of the impedance in order to dissipate faster the energy of the system, limiting the peaks of force and avoiding losses of contact. The optimal switching criteria are deduced for every parameter in order to dissipate the energy of the system as fast as possible. The results are verified in simulation. © 2011 Cambridge University Press., The authors want to express their gratitude to the Plan Nacional de I+D, Comision Interministerial de Ciencia y Tecnologia (FEDER-CICYT) for the partial financing of this work under the projects DPI2009-13830-C02-01 and DPI2010-20814-C02-02.