Pasar al contenido principal

DESARROLLO SOSTENIBLE Y MODELADO DE COMPOSITES TERMOPLASTICOS (GREEN COMPOSITE)

DPI2010-20333

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2010
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Flexural behavior and water absorption of asymmetrical sandwich composites from natural fibers and cork agglomerate core

  • Hoto, Rene
  • Furundarena Doval, Gurutze
  • Torres, J.P.
  • Andrés de la Esperanza, Francisco Javier
  • Muñoz Dominguez, Eva|||0000-0001-5648-484X
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
This work addresses an experimental investigation concerning flexural and water absorption behavior of a novel low-cost green composite asymmetric sandwich. For specimen manufacturing, an agglomerate cork panel and natural fiber reinforcements, namely basalt and flax fiber were used. A bio-based epoxy resin was used as matrix and the specimens were manufactured using vacuum assisted hand lay-up. For some specimens the core material was altered allowing resin infiltration between the granules. Results show that both, the core type and specimens stance influence the flexural behavior. More importantly, all specimens showed a very good energy absorption behavior during bending tests. The water absorption of the specimens was significantly reduced by the infiltration of resin inside the core material. These attractive performances reveal that the green composites based sandwich proposed in this work can be a good alternative to traditional ones., This research work is supported by the Spanish Ministerio de Ciencia e Innovacion, project DPI2010-20333 and the Generalitat Valenciana through programme PROMETEO/2009/063.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A two-phase flow model to simulate mold filling and saturation in Resin Transfer Molding

  • Gascón Martínez, María Llanos|||0000-0003-3842-0142
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
  • LeBel, F.
  • Ruiz, E.
  • Trochu, F.
This paper addresses the numerical simulation of void formation and transport during mold filling in Resin Transfer Molding (RTM). The saturation equation, based on a two-phase flow model resin/air, is coupled with Darcy s law and mass conservation to simulate the unsaturated filling flow that takes place in a RTM mold when resin is injected through the fiber bed. These equations lead to a system composed of an advection diffusion equation for saturation including capillary effects and an elliptic equation for pressure taking into account the effect of air residual saturation. The model introduces the relative permeability as a function of resin saturation. When capillary effects are omitted, the hyperbolic nature of the saturation equation and its strong coupling with Darcy equation through relative permeability represent a challenging numerical issue. The combination of the constitutive physical laws relating permeability to saturation with the coupled system of the pressure and saturation equations allows predicting the saturation profiles. The model was validated by comparison with experimental data obtained for a fiberglass reinforcement injected in a RTM mold at constant flow rate. The saturation measured as a function of time during the resin impregnation of the fiber bed compared very well with numerical predictions., The authors acknowledge financial support of the Spanish Government (Projects DPI2010-20333 and DPI2013-44903-R-AR), of the National Science and Research Council of Canada (NSERC) and of the Canada Reseach Chair (CRC) program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Manufacture of Green-Composite Sandwich Structures with Basalt Fiber and Bioepoxy Resin

  • Torres, J.T.
  • Hoto, Rene
  • Andrés de la Esperanza, Francisco Javier
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
Nowadays, there is a growing interest for the use and development ofmaterials synthesized fromrenewable sources in the polymer composites manufacturing industry; this applies for both matrix and reinforcement components. In the present research, a novel basalt fibre reinforced (BFR) bioepoxy green composite is proposed as an environmentally friendly alternative to traditional petroleum-derived composites. In addition, this material system was combined with cork as core material for the fabrication of fibre composite sandwich structures. Mechanical properties of both skin and core materials were assessed through flexural and tensile tests. Finite element (FEM) simulations for the mechanical stress analysis of the sandwich material were carried out, and a maximumallowable shear stress for material failure under bending loads was established. Permeabilitymeasurements of the basalt fabrics were carried out in order to perform numerical simulations of liquid composite moulding (LCM) processes on the PAMRTM software. The proposed green-composite sandwich material was used for the fabrication of a longboard as a case study for a sports equipment application. Numerical simulations of the mould filling stage allowed the determination of an optimal mould filling strategy. Finally, the load-bearing capacity of the board was studied by means of FEM simulations, and the presented design proved to be acceptable for service., This research work is supported by the Spanish Ministerio de Ciencia e Innovacion, Project DPI2010-20333, and the Generalitat Valenciana through Programme PROME-TEO/2009/063.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Water absorption behaviour and its effect on the mechanical properties of flax fibre reinforced bioepoxy composites

  • Muñoz Dominguez, Eva|||0000-0001-5648-484X
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
In the context of sustainable development, considerable interest is being shown in the use of natural fibres like as reinforcement in polymer composites and in the development of resins from renewable resources. This paper focus on eco-friendly and sustainable green composites manufacturing using Resin Transfer Moulding (RTM) process. Flax fibre reinforced bioepoxy composites at different weight fractions (40 and 55wt%) were prepared in order to study the effect of water absorption on their mechanical properties. Water absorption test was carried out by immersion specimens in water bath at room temperature for a time duration. The process of water absorption of these composites was found to approach Fickian diffusion behavior. Diffusion coefficients and maximum water uptake values were evaluated, the results showed that both increased with an increase in fibre content. Tensile and flexural properties of water immersed specimens were evaluated and compared to dry composite specimens. The results suggest that swelling of flax fibres due to water absorption can have positive effects on mechanical properties of the composite material. The results of this study showed that RTM process could be used to manufacture natural fibre reinforced composites with good mechanical properties even for potential applications in a humid environment, This research is supported by the Spanish Ministerio de Ciencia e Innovacion, Projects PAID-05-11, DPI 2010-20333, and DPI 2013-44903-R-AR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A numerical simulation of woven/anionic polyamide 6 composite part manufacturing using structural reactive injection moulding process

  • García Manrique, Juan Antonio|||0000-0001-9507-0746
  • Gascón Martínez, María Llanos|||0000-0003-3842-0142
  • Hoto, Rene
  • Andrés de la Esperanza, Francisco Javier
In this work, a structural reactive injection moulding process using reactive anionic polyamide 6 (APA-6) is studied. Semi-empirical equations for the prediction of the APA-6 reaction kinetics and an advection equation for void transport are used in the numerical scheme. A complex numerical simulation of reactive injection of ε-caprolactam was developed for a three-dimensional industrial part. The validity of the approach is demonstrated for determining an effective injection strategy, including the position of vents and gates and the most effective parameter values for minimum mould filling time without the formation of voids., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research work is supported by the Spanish Ministry of Science and Innovation, project DPI2010-20333 and the Generalitat Valenciana through programme PROMETEO/2009/063.