Pasar al contenido principal

FABRICACION DE COMPOSITES DE ALTAS PRESTACIONES SIN AUTOCLAVE (OOA)

DPI2013-44903-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A two-phase flow model to simulate mold filling and saturation in Resin Transfer Molding

  • Gascón Martínez, María Llanos|||0000-0003-3842-0142
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
  • LeBel, F.
  • Ruiz, E.
  • Trochu, F.
This paper addresses the numerical simulation of void formation and transport during mold filling in Resin Transfer Molding (RTM). The saturation equation, based on a two-phase flow model resin/air, is coupled with Darcy s law and mass conservation to simulate the unsaturated filling flow that takes place in a RTM mold when resin is injected through the fiber bed. These equations lead to a system composed of an advection diffusion equation for saturation including capillary effects and an elliptic equation for pressure taking into account the effect of air residual saturation. The model introduces the relative permeability as a function of resin saturation. When capillary effects are omitted, the hyperbolic nature of the saturation equation and its strong coupling with Darcy equation through relative permeability represent a challenging numerical issue. The combination of the constitutive physical laws relating permeability to saturation with the coupled system of the pressure and saturation equations allows predicting the saturation profiles. The model was validated by comparison with experimental data obtained for a fiberglass reinforcement injected in a RTM mold at constant flow rate. The saturation measured as a function of time during the resin impregnation of the fiber bed compared very well with numerical predictions., The authors acknowledge financial support of the Spanish Government (Projects DPI2010-20333 and DPI2013-44903-R-AR), of the National Science and Research Council of Canada (NSERC) and of the Canada Reseach Chair (CRC) program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tool wear study in edge trimming on basalt fibre reinforced plastics

  • Navarro-Mas, M.D.|||0000-0003-2022-8857
  • Meseguer, Maria-Desamparados|||0000-0003-0254-7993
  • Sánchez Galdón, Ana Isabel|||0000-0002-3159-8020
  • Gutiérrez, S. C.|||0000-0002-9106-9120
[EN] In machining of reinforced fibre composite parts, abrasive fibres and material heterogeneity produce poor surface finish, delamination and tool wear. In this research, basalt fibre reinforced plastic is machined with edge trimming in order to study tool wear, using a tool holder of diameter 25 mm, with two exchangeable uncoated carbide cutting inserts. Cutting conditions (cutting speed, feed per tooth and depth) and material characteristics (fibre volume fraction and fibre orientation) are evaluated to know their influence in the flank wear (Vb) of the tool. An analysis of variance (ANOVA) was performed to study flank wear and material removal rate, and a generalized linear model (GLM) was developed. More influence variables in the flank wear are the machining conditions, being the tool life suitable for this machining and material., This work was funded by the Research Project DPI2013-44903-R-AR of the MINER.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Delamination Study in Edge Trimming of Basalt Fiber Reinforced Plastics (BFRP)

  • Navarro-Mas, M.D.|||0000-0003-2022-8857
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
  • Meseguer, Maria-Desamparados|||0000-0003-0254-7993
  • Ordeig Fernández, Isabel Natividad|||0000-0002-0131-0209
  • Sánchez Galdón, Ana Isabel|||0000-0002-3159-8020
[EN] Although there are many machining studies of carbon and glass fiber reinforced plastics, delamination and tool wear of basalt fiber reinforced plastics (BFRP) in edge trimming has not yet studied. This paper presents an end milling study of BFRP fabricated by resin transfer molding (RTM), to evaluate delamination types at the top layer of the machined edge with different cutting conditions (cutting speed, feed rate and depth of cut) and fiber volume fraction (40% and 60%). This work quantifies delamination types, using a parameter Sd/L, that evaluates the delamination area (Sd) and the length (L), taking into account tool position in the yarn and movement of yarns during RTM process, which show the random nature of delamination. Delamination was present in all materials with 60% of fiber volume. High values of tool wear did not permit to machine the material due to an excessive delamination. Type II delamination was the most usual delamination type and depth of cut has influence on this type of delamination., The authors gratefully acknowledge the funding by the Ministerio de Educacion y Ciencia of the Spanish government under grant DPI2013-44903-R-AR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Water absorption behaviour and its effect on the mechanical properties of flax fibre reinforced bioepoxy composites

  • Muñoz Dominguez, Eva|||0000-0001-5648-484X
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
In the context of sustainable development, considerable interest is being shown in the use of natural fibres like as reinforcement in polymer composites and in the development of resins from renewable resources. This paper focus on eco-friendly and sustainable green composites manufacturing using Resin Transfer Moulding (RTM) process. Flax fibre reinforced bioepoxy composites at different weight fractions (40 and 55wt%) were prepared in order to study the effect of water absorption on their mechanical properties. Water absorption test was carried out by immersion specimens in water bath at room temperature for a time duration. The process of water absorption of these composites was found to approach Fickian diffusion behavior. Diffusion coefficients and maximum water uptake values were evaluated, the results showed that both increased with an increase in fibre content. Tensile and flexural properties of water immersed specimens were evaluated and compared to dry composite specimens. The results suggest that swelling of flax fibres due to water absorption can have positive effects on mechanical properties of the composite material. The results of this study showed that RTM process could be used to manufacture natural fibre reinforced composites with good mechanical properties even for potential applications in a humid environment, This research is supported by the Spanish Ministerio de Ciencia e Innovacion, Projects PAID-05-11, DPI 2010-20333, and DPI 2013-44903-R-AR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Contribution to Reduce the Influence of the Free Sliding Edge on Compression-After-Impact Testing of Thin-Walled Undamaged Composites Plates

  • Linke, Markus
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
[EN] Standard Compression-After-Impact test devices show a weakening effect on thin-walled specimens due to a free panel edge that is required for compression. As a result, thin-walled undamaged samples do not break in the free measuring area but near the free edge and along the supports. They also show a strength reduction due to the free edge which can become potentially relevant for very weakly damaged panels. In order to reduce the free edge influence on the measured strength, a modified Compression-After-Impact test device has been developed. In an experimental investigation with carbon fiber reinforced plastics, the modified device is compared with a standard device. It is shown that thin-walled undamaged specimens investigated with the modified device now mainly break within the free measuring area and no longer at the free edge and along the bearings as it is the case for standard test devices. The modified device does not cause a free edge weakening effect in comparison to standard devices. The modified device is therefore more suitable for determining the compression strengths of undamaged thin-walled composite plates, This research was partially supported by the Spanish government under grant number DPI2013-44903-R-AR through funding the specimens as well as the CAI-standard device. The Article Processing Charge is also funded under that grant number.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An infiltration strategy to repair Carbon Fiber Reinforced Polymer (CFRP) parts

  • Garcia-Girón, Reineiry Emilio
  • Linke, Markus
  • Nesslinger, S.
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
[EN] This paper presents a methodology to determine the damage levels of laminate carbon fibre reinforced plastics (CFRP) parts after controlled impacts. These techniques will be used to perform a re-infiltration technique to repair composite parts and to reduce maintenance costs. It will be included the manufacturing processes, material characterization and the application of the AITM-0010 standard. Also, it is propose the use of NUT Ultrasonic inspection to determine and characterized the degree of the damage measured. This NDT method uses an advanced pulse-echo technique that through allow exploration of different angles, shapes and positions of defects. (C) 2017 The Authors. Published by Elsevier B.V., The authors gratefully acknowledge the partial funding by the Federal Ministry of Education and Research of the German government under grant 03FH029AN4 and the Spanish government under DPI2013-44903-R-AR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical prediction of saturation in dual scale fibrous reinforcements during Liquid Composite Molding

  • Gascón Martínez, María Llanos|||0000-0003-3842-0142
  • García Manrique, Juan Antonio|||0000-0001-9507-0746
  • Lebel, F.
  • Ruiz, E.
  • Trochu, F.
This paper presents a fractional flow model based on two-phase flow, resin and air, through a porous medium to simulate numerically Liquid Composites Molding (LCM) processes. It allows predicting the formation, transport and compression of voids in the modeling of LCM. The equations are derived by combining Darcy’s law and mass conservation for each phase (resin/air). In the model, the relative permeability and capillary pressure depend on saturation. The resin is incompressible and the air slightly compressible. Introducing some simplifications, the fractional flow model consists of a saturation equation coupled with a pressure/velocity equation including the effects of air solubility and compressibility. The introduction of air compressibility in the pressure equation allows for the numerical prediction of the experimental behavior at low constant resin injection flow rate. A good agreement was obtained between the numerical prediction of saturation in a glass fiber reinforcement and the experimental observations during the filling of a test mold by Resin Transfer Molding (RTM). 2015 Elsevier Ltd. All rights reserved., The authors acknowledge financial support of the Spanish Government (Project DPI2013-44903-R-AR).