Pasar al contenido principal

BIOLOGIA SINTETICA PARA LA MEJORA EN BIOPRODUCCION: DISEÑO, OPTIMIZACION, MONITORIZACION Y CONTROL

DPI2014-55276-C5-1-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2014
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

A systems engineering approach to model, tune and test synthetic gene circuits

  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
La biología sintética se define como la ingeniería de la biología: el (re)diseño y construcción de nuevas partes, dispositivos y sistemas biológicos para realizar nuevas funciones con fines útiles, que se basan en principios elucidados de la biología y la ingeniería. Para facilitar la construcción rápida, reproducible y predecible de estos sistemas biológicos a partir de conjuntos de componentes es necesario desarrollar nuevos métodos y herramientas. La tesis plantea la optimización multiobjetivo como el marco adecuado para tratar los problemas comunes que surgen en el diseño racional y el ajuste óptimo de los circuitos genéticos sintéticos. Utilizando un enfoque clásico de ingeniería de sistemas, la tesis se centra principalmente en: i) el modelado de circuitos genéticos sintéticos basado en los primeros principios, ii) la estimación de parámetros de modelos a partir de datos experimentales y iii) el ajuste basado en modelos para lograr el desempeño deseado de los circuitos. Se han utilizado dos circuitos genéticos sintéticos de diferente naturaleza y con diferentes objetivos y problemas: un circuito de realimentación de tipo 1 incoherente (I1-FFL) que exhibe la importante propiedad biológica de adaptación, y un circuito de detección de quorum sensing y realimentación (QS/Fb) que comprende dos bucles de realimentación entrelazados -uno intracelular y uno basado en la comunicación de célula a célula- diseñado para regular el nivel medio de expresión de una proteína de interés mientras se minimiza su varianza a través de la población de células. Ambos circuitos han sido analizados in silico e implementados in vivo. En ambos casos, se han desarrollado modelos de estos circuitos basado en primeros principios. Se presta especial atención a ilustrar cómo obtener modelos de orden reducido susceptibles de estimación de parámetros, pero manteniendo el significado biológico. La estimación de los parámetros del modelo a partir de los datos experimentales se considera en diferentes escenarios, tanto utilizando modelos determinísticos como estocásticos. Para el circuito I1-FFL se consideran modelos determinísticos. Aquí, la tesis plantea la utilización de modelos locales utilizando la optimización multiobjetivo para realizar la estimación de parámetros del modelo bajo escenarios con estructura de modelo incompleta. Para el circuito QS/Fb, una estructura controlada por realimentación, el problema tratado es la falta de excitabilidad de las señales. La tesis propone una metodología de estimación en dos etapas utilizando modelos estocásticos. La metodología permite utilizar datos de curso temporal promediados de la población y mediciones de distribución en estado estacionario para una sola célula. El ajuste de circuitos basado en modelos para lograr un desempeño deseado también se aborda mediante la optimización multiobjetivo. Para el circuito QS/Fb se realiza un análisis estocástico completo. La tesis aborda cómo tener en cuenta correctamente tanto el ruido intrínseco como el extrínseco, las dos principales fuentes de ruido en los circuitos genéticos. Se analiza el equilibrio entre ambas fuentes de ruido y el papel que desempeñan en el bucle de realimentación intracelular, y en la realimentación extracelular de toda la población. La principal conclusión es que la compleja interacción entre ambos canales de realimentación obliga al uso de la optimización multiobjetivo para el adecuado ajuste del circuito. En esta tesis además del uso adecuado de herramientas de optimización multiobjetivo, la principal preocupación es cómo derivar directrices para el ajuste in silico de parámetros de circuitos que puedan aplicarse de forma realista in vivo en un laboratorio estándar. Como alternativa al análisis de sensibilidad de parámetros clásico, la tesis propone el uso de técnicas de clustering a lo largo de los frentes de Pareto, relacionando el compr, This work has been partially supported by the Spanish Government (CICYT DPI2014- 55276-C5-1) and the European Union (FEDER). The author was recipient of the grant Formación de Personal Investigador by the Universitat Politècnica de València, subprogram 1 (FPI/2013-3242). She was also recipient of the competitive grants for pre-doctoral stays Erasmus Student Placement-European Programme 2015, and FPI Mobility program 2016 of the Universitat Politècnica de València. She also received the competitive grant for a pre-doctoral stay Becas de movilidad para Jóvenes Profesores e Investigadores 2016, Programa de Becas Iberoamérica of the Santander Bank.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

PLS model building with missing data: New algorithms and a comparative study

  • Folch-Fortuny, Abel
  • Arteaga, Francisco
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] New algorithms to deal with missing values in predictive modelling are presented in this article. Specifically, 2 trimmed scores regression adaptations are proposed, one from principal component analysis model building with missing data (MD) and other from partial least squares regression model exploitation with missing values. Using these methods, practitioners can impute MD both in the explanatory/predictor and the dependent/response variables. Partial least squares is used here to build the multivariate calibration models; however, any regression method can be used after MD imputation. Four case studies, with different latent structures, are analysed here to compare the trimmed scores regression¿based methods against state-of-the-art approaches. The MATLAB code for these methods is also provided for its direct implementation at http://mseg.webs.upv.es, under a GNU license., Spanish Ministry of Science and Innovation; FEDER; European Union, Grant/Award Number: DPI2011-28112-C04-02 and DPI2014-55276-C5-1R; Spanish Ministry of Economy and Competitiveness, Grant/Award Number: ECO2013-43353-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Otros (Other)

Modelado de sistemas bioquímicos: De la Ley de Acción de Masas a la Aproximación Lineal del Ruido, Modelling biochemical systems: from Mass Action Kinetics to Linear Noise Approximation

  • Picó, Jesús|||0000-0003-4144-3521
  • Vignoni, Alejandro|||0000-0001-9977-7132
  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
  • Picó i Marco, Enric
[EN] In the last decade we have witnessed a growing application of engineering techniques to biology. Areas such as Systems Biology or, more recently, Synthetic Biology, get more and more attention from the engineers. Specifically, modeling in these fields makes possible the generation of new experimentally verifiable hypothesis, and new ways of biological intervention, as well as more or less mechanistic explanations of experimental results. A model-based approximation requires the consideration of the biochemical reactions dynamics and their regulation. The first part of this tutorial describes the deterministic modeling and model reduction techniques, as applied to the class of biochemical reactions specific to molecular cell biology.Noise plays a crucial role in the biological circuitry dynamics. In the field of automatic control there is a long tradition of modeling using linear stochastic differential equations, under the simplifying assumption that noise has a magnitude independent of the state. This assumption is not valid in biological circuits. The second part of the tutorial describes the most widely used methods for stochastic modeling in molecular cell biology, paying special attention to the so-called linear noise approximation. , [ES] Durante la ultima década hemos vivido una creciente aplicación de técnicas propias de las ingenierías a la biología. Áreas como la Biología de Sistemas o, más recientemente, la Biología Sintética, reciben una atención cada vez mayor por parte de los ingenieros. En particular, el modelado en estos ámbitos permite la generación de nuevas hipótesis contrastables experimentalmente, y de nuevas formas de intervención biológica, así como explicaciones más o menos mecanicistas de los resultados experimentales. Una aproximación basada en modelo requiere considerar la dinámica de las reacciones bioquímicas y su regulación. En la primera parte de este tutorial se introducen el modelado determinista y reducción de modelos de la clase de reacciones bioquímicas propias de la biología molecular celular.El ruido juega un papel crucial en la dinámica de los circuitos biológicos. En el área de control automático hay una larga tradición de modelado mediante ecuaciones diferenciales estocásticas lineales, bajo la hipótesis simplificadora de asumir que el ruido tiene una magnitud independiente de la del estado. Esta hipótesis no es válida en los circuitos biológicos. En la segunda parte del tutorial se describen los métodos de modelado estocástico más usados en biología molecular, con especial atención a denominada aproximación lineal del ruido., Este trabajo ha sido realizado parcialmente gracias al apoyo de los proyectos FEDER-CICYT DPI2011-28112-C04-01, y DPI2014-55276-C5-1. Yadira Boada agradece la beca FPI/2013- 3242 de la Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Kernel-Partial Least Squares regression coupled to pseudo-sample trajectories for the analysis of mixture designs of experiments

  • Vitale, Raffaele
  • Palací-López, Daniel Gonzalo
  • Kerkenaar, Harmen
  • Postma, GJ
  • Buydens, Lutgarde
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] This article explores the potential of Kernel-Partial Least Squares (K-PLS) regression for the analysis of data proceeding from mixture designs of experiments. Gower's idea of pseudo-sample trajectories is exploited for interpretation purposes. The results show that, when the datasets under study are affected by severe nonlinearities and comprise few observations, the proposed approach can represent a feasible lternative to classical methodologies (i.e. Scheffe polynomial fitting by means of Ordinary Least Squares - OLS - and Cox polynomial fitting by means of Partial Least Squares - PLS). Furthermore, a way of recovering the parameters of a Scheffe model (provided that it holds and has the same complexity as the K-PLS one) from the trend of the aforementioned pseudo-sample trajectories is illustrated via a simulated case-study., This research work was partially supported by the Spanish Ministry of Economy and Competitiveness under the project DPI2014-55276-C5-1R and Shell Global Solutions International B.V. (Amsterdam, The Netherlands).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Selecting the number of factors in principal component analysis by permutation testing Numerical and practical aspects

  • Vitale, Raffaele
  • Westerhuis, Johan A.
  • Naes, Tormod
  • Smilde, Age K.
  • De Noord, Onno E.
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] Selecting the correct number of factors in principal component analysis (PCA) is a critical step to achieve a reasonable datamodelling,where the optimal strategy strictly depends on the objective PCA is applied for. In the last decades, much work has been devoted to methods like Kaiser's eigenvalue greater than 1 rule, Velicer's minimum average partial rule, Cattell's scree test, Bartlett's chi-square test, Horn's parallel analysis, and cross-validation. However, limited attention has been paid to the possibility of assessing the significance of the calculated components via permutation testing. That may represent a feasible approach in case the focus of the study is discriminating relevant fromnonsystematic sources of variation and/or the aforementioned methodologies cannot be resorted to (eg, when the analysed matrices do not fulfill specific properties or statistical assumptions). The main aim of this article is to provide practical insights for an improved understanding of permutation testing, highlighting its pros and cons,mathematically formalising the numerical procedure to be abided bywhen applying it for PCA factor selection by the description of a novel algorithm developed to this end, and proposing ad hoc solutions for optimising computational time and efficiency., Spanish Ministry of Economy and Competitiveness, Grant/Award Number: DPI2014-55276-C5-1R; Shell Global Solutions International B.V.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Parameter Identification in Synthetic Biological Circuits Using Multi-Objective Optimization

  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
  • Vignoni, Alejandro|||0000-0001-9977-7132
  • Picó, Jesús|||0000-0003-4144-3521
  • Reynoso Meza, Gilberto
[EN] Synthetic biology exploits the of mathematical modeling of synthetic circuits both to predict the behavior of the designed synthetic devices, and to help on the selection of their biological coin portents. The increasing complexity of the circuits being designed requires performing approximations and model reductions to get handy models. Parameter estimation in these models remains a challenging problem that has usually been addressed by optimizing the weighted combination of different prediction errors to obtain a single solution. The single-objective approach is inadequate to incorporate different kinds of experiments, and to identify parameters for an ensemble of biological circuit models. We present a methodology based on multi-objective optimization to perform parameter estimation that can fully harness to ensembles of local models for biological circuits. The methodology uses a global multi-objective evolutionary algorithm and a multi-criteria decision making strategy to select the most suitable solutions. Our approach finds an approximation to the Pareto optimal set of model parameters that correspond to each experimental scenario. Then, the Pareto set was clustered according to the experimental scenarios. This, in turn, allows to analyze the sensitivity of model parameters for different scenarios. Finally, we show the methodology applicability through the case study of a genetic incoherent feed-forward circuit, under different concentrations of the inducer input signal. (C) 2016 IFAC (International Federation Of Automatic Control) Hosting by Elsevier Ltd. All rights reserved., This work is partially supported by Spanish government and European Union (FEDER-CICYT DPI2011-28112-C04-01, and DPI2014-55276-C5-1). Y.B. thanks grant FP/2013-3242 of Universitat Politecnica de Valencia and Becas Iberoamerica of Santander Group, Spain 2015. G.R.M. thanks the partial support provided by the postdoctoral fellowship BJT-304804/2014-2 from the National Council of Scientific and Technologic Development of Brazil. A.V. thanks the Max Planck Society, the CSBD and the MPI-CBG. We are grateful to Dr. C,Bauerl and Dr, D. Provencio at the SB2CLab for their help in plasmid construction and getting experimental data. Also to Dr. V. Monedero at IATACSIC for allowing us to use the POLARstar plate reader at his lab,
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enabling network inference methods to handle missing data and outliers

  • Folch-Fortuny, Abel
  • Fernández Villaverde, Alejandro
  • Rodríguez Banga, Julio
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] Background: The inference of complex networks from data is a challenging problem in biological sciences, as well as in a wide range of disciplines such as chemistry, technology, economics, or sociology. The quantity and quality of the data greatly affect the results. While many methodologies have been developed for this task, they seldom take into account issues such as missing data or outlier detection and correction, which need to be properly addressed before network inference. Results: Here we present an approach to (i) handle missing data and (ii) detect and correct outliers based on multivariate projection to latent structures. The method, called trimmed scores regression (TSR), enables network inference methods to analyse incomplete datasets by imputing the missing values coherently with the latent data structure. Furthermore, it substitutes the faulty values in a dataset by proper estimations. We provide an implementation of this approach, and show how it can be integrated with any network inference method as a preliminary data curation step. This functionality is demonstrated with a state of the art network inference method based on mutual information distance and entropy reduction, MIDER. Conclusion: The methodology presented here enables network inference methods to analyse a large number of incomplete and faulty datasets that could not be reliably analysed so far. Our comparative studies show the superiority of TSR over other missing data approaches used by practitioners. Furthermore, the method allows for outlier detection and correction., Research in this study was partially supported by the European Union through project BioPreDyn (FP7-KBBE 289434), and the Spanish Ministry of Science and Innovation and FEDER funds from the European Union through grants MultiScales (DPI2011-28112-C04-02, DPI2011-28112-C04-03), and SynBioFactory (DPI2014-55276-C5-1-R, DPI2014-55276-C5-2-R). AF Villaverde also acknowledges funding from the Xunta de Galicia through an I2C postdoctoral fellowship (I2C ED481B 2014/133-0). We also gratefully acknowledge Associate Professor Francisco Arteaga for his help in the adaptation of TSR to the PCA model building context.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multi-objective optimization framework to obtain model-based guidelines for tuning biological synthetic devices: an adaptive network case

  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
  • Picó, Jesús|||0000-0003-4144-3521
  • Vignoni, Alejandro|||0000-0001-9977-7132
  • Reynoso Meza, Gilberto
Background: Model based design plays a fundamental role in synthetic biology. Exploiting modularity, i.e. using biological parts and interconnecting them to build new and more complex biological circuits is one of the key issues. In this context, mathematical models have been used to generate predictions of the behavior of the designed device. Designers not only want the ability to predict the circuit behavior once all its components have been determined, but also to help on the design and selection of its biological parts, i.e. to provide guidelines for the experimental implementation. This is tantamount to obtaining proper values of the model parameters, for the circuit behavior results from the interplay between model structure and parameters tuning. However, determining crisp values for parameters of the involved parts is not a realistic approach. Uncertainty is ubiquitous to biology, and the characterization of biological parts is not exempt from it. Moreover, the desired dynamical behavior for the designed circuit usually results from a trade-off among several goals to be optimized. Results: We propose the use of a multi-objective optimization tuning framework to get a model-based set of guidelines for the selection of the kinetic parameters required to build a biological device with desired behavior. The design criteria are encoded in the formulation of the objectives and optimization problem itself. As a result, on the one hand the designer obtains qualitative regions/intervals of values of the circuit parameters giving rise to the predefined circuit behavior; on the other hand, he obtains useful information for its guidance in the implementation process. These parameters are chosen so that they can effectively be tuned at the wet-lab, i.e. they are effective biological tuning knobs. To show the proposed approach, the methodology is applied to the design of a well known biological circuit: a genetic incoherent feed-forward circuit showing adaptive behavior. Conclusion: The proposed multi-objective optimization design framework is able to provide effective guidelines to tune biological parameters so as to achieve a desired circuit behavior. Moreover, it is easy to analyze the impact of the context on the synthetic device to be designed. That is, one can analyze how the presence of a downstream load influences the performance of the designed circuit, and take it into account., Research in this area is partially supported by Spanish government and European Union (FEDER-CICYT DPI2011-28112-C04-01, and DPI2014-55276-C5-1-R). Yadira Boada thanks grant FPI/2013-3242 of Universitat Politecnica de Valencia; Gilberto Reynoso-Meza gratefully acknowledges the partial support provided by the postdoctoral fellowship BJT-304804/2014-2 from the National Council of Scientific and Technologic Development of Brazil (CNPq) for the development of this work. We are grateful to Alejandra Gonzalez-Bosca for her collaboration on this topic while doing her Bachelor thesis, and to Dr. Jose Luis Pitarch from Universidad de Valladolid for his advise in algorithmic implementations and for proof reading the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Segmentation techniques in image analysis: A comparative study

  • Vitale, Raffaele
  • López García, Fernando
  • BLASCO IVARS, JOSE
  • Prats-Montalbán, José Manuel|||0000-0001-6294-4486
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] Nowadays, the detection, localization, and quantification of different kinds of features in an RGB image (segmentation) is extremely helpful for, e.g., process monitoring or customer product acceptance. In this article, some of the most commonly used RGB image segmentation approaches are compared in an orange quality control case study. Analysis of variance and correspondence analysis are combined for determining their most relevant differences and highlighting their pros and cons., Spanish Ministry of Economy and Competitiveness, Grant/Award Number: DPI2014-55276-C5-1R; Spanish National Institute for Agricultural and Food Research and Technology (INIA), Grant/Award Number: RTA2012-00062-C04-01; European Regional Development Fund (FEDER); Shell Global Solutions International B.V.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multivariate statistical process control charts for batch monitoring of transesterification reactions for biodiesel production based on near-infrared spectroscopy

  • Sales Figueiredo, Rafaella
  • Vitale, Raffaele
  • Pimentel, Maria Fernanda
  • de Lima, Suzana Moreira
  • Stragevitch, Luiz
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] This work describes an application of Multivariate Statistical Process Control to monitor soybean oil transesterification. For the development of multivariate control charts, near infrared spectra were acquired in-line during the evolution of ten batches under Normal Operating Conditions. They were then organized in a three-way array (batch × spectral variable × time). This structure was analysed by the two most commonly used approaches to develop batch monitoring schemes for handling such kind of data, referred to as Nomikos-MacGregor (NM) and Wold-Kettaneh-Friden-Holmberg (WKFH), respectively. To assess the performance of the approaches, eight test batches, during which specific interferences were induced, were manufactured. When applied for off-line monitoring, both NM and WKFH correctly pointed out such intentionally produced failures. On the other hand, concerning on-line monitoring, NM exhibited a better fault detection capability than WKFH. Contribution plots were found to highlight the spectral region mostly affected by the disturbances regardless of the modelling strategy resorted to., The authors would like to thank FACEPE/NUQAAPE, CNPq/INCTAA science funding programs for partial financial support. Research fellowships granted by the Brazilian agencies ANP/Petrobras and CNPq are also gratefully acknowledged. This research work was partially supported by the Spanish Ministry of Economy and Competitiveness under the project DPI2014-55276-C5-1R and Shell Global Solutions International B.V. (Amsterdam, The Netherlands).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Calibration transfer between NIR spectrometers: new proposals and a comparative study

  • Folch-Fortuny, Abel
  • Vitale, Raffaele
  • De Noord, Onno E.
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] Calibration transfer between near-infrared (NIR) spectrometers is a subtle issue in chemometrics and process industry. In fact, as even very similar instruments may generate strongly different spectral responses, regression models developed on a first NIR system can rarely be used with spectra collected by a second apparatus. In this work, two novel methods to perform calibration transfer between NIR spectrometers are proposed. Both of them permit to exploit the specific relationships between instruments for imputing new unmeasured spectra, which will be then resorted to for building an improved predictive model, suitable for the analysis of future incoming data. Specifically, the two approaches are based on trimmed scores regression and joint-Y partial least squares regression, respectively. The performance of these novel strategies will be assessed and compared to that of well-established techniques such as maximum likelihood principal component analysis and piecewise direct standardisation in two real case studies., This research work was partially supported by the Spanish Ministry of Economy and Competitiveness under the project DPI2014-55276-C5-1R and Shell Global Solutions International B.V. (Amsterdam, the Netherlands).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Contractivity of a genetic circuit with internal feedback and cell-to-cell communication

  • Picó-Marco, Enric
  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
  • Picó, Jesús|||0000-0003-4144-3521
  • Vignoni, Alejandro|||0000-0001-9977-7132
[EN] We consider a realistic model of the synthetic gene circuit combining cell-to-cell communication system via quorum sensing, and a synthetic repressible promoter implementing intracellular negative feedback control. The circuit has been shown to increase robustness with respect to both extrinsic and intrinsic noise elsewhere. As a first step towards an analytic analysis, in this paper we use contraction theory to perform a stability analysis. From it, we infer the components of the circuit most affecting the rate of contractivity, using biologically sensible values of the circuit parameters., This research was partially funded by grant FEDER-CICYT DPI2014-55276-C5-1-R. Yadira Boada thanks grant FPI/2013-3242 of the Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fusion of genomic, proteomic and phenotypic data: the case of potyviruses

  • Folch-Fortuny, A.
  • BOSQUE-CHACON, GABRIEL
  • Picó, Jesús
  • Ferrer, A.
  • Elena, S.F.
Data fusion has been widely applied to analyse different sources of information, combining all of them in a single multivariate model. This methodology is mandatory when different omic data sets must be integrated to fully understand an organism using a systems biology approach. Here, a data fusion procedure is presented to combine genomic, proteomic and phenotypic data sets gathered for Tobacco etch virus (TEV). The genomic data correspond to random mutations inserted in most viral genes. The proteomic data represent both the effect of these mutations on the encoded proteins and the perturbation induced by the mutated proteins to their neighbours in the protein protein interaction net- work (PPIN). Finally, the phenotypic trait evaluated for each mutant virus is replicative fitness. To analyse these three sources of information a Partial Least Squares (PLS) regression model is fitted in order to extract the latent variables from data that explain (and relate) the significant variables to the fitness of TEV. The final output of this methodology is a set of functional modules of the PPIN relating topology and mutations with fitness. Throughout the re-analysis of these diverse TEV data, we generated valuable information on the mechanism of action of certain mutations and how they translate into organismal fitness. Results show that the effect of some mutations goes beyond the protein they directly affect and spreads on the PPIN to neighbour proteins, thus defining functional modules., This work was supported by the Spanish Ministerio de Economia y Competitividad grants BFU2012-30805 (to SFE), and DPI2011-28112-C04-02, DPI2011-28112-C04-01, DPI2014-55276-C5-1-R (to AF and JP) and by Generalitat Valenciana grant PROMETEOII/2014/021 (to SFE). The first two authors are recipients of fellowships from the Spanish Ministerio de Economia y Competitividad: BES-2012-053772 (to GB) and BES-2012-057812 (to AF-F).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Principal elementary mode analysis (PEMA)

  • Folch Fortuny, Abel
  • Marques, Rodolfo
  • Isidro, Ines A.
  • Oliveira, Rui
  • Ferrer, Alberto|||0000-0001-7244-5947
Principal component analysis (PCA) has been widely applied in fluxomics to compress data into a few latent structures in order to simplify the identification of metabolic patterns. These latent structures lack a direct biological interpretation due to the intrinsic constraints associated with a PCA model. Here we introduce a new method that significantly improves the interpretability of the principal components with a direct link to metabolic pathways. This method, called principal elementary mode analysis (PEMA), establishes a bridge between a PCA-like model, aimed at explaining the maximum variance in flux data, and the set of elementary modes (EMs) of a metabolic network. It provides an easy way to identify metabolic patterns in large fluxomics datasets in terms of the simplest pathways of the organism metabolism. The results using a real metabolic model of Escherichia coli show the ability of PEMA to identify the EMs that generated the different simulated flux distributions. Actual flux data of E. coli and Pichia pastoris cultures confirm the results observed in the simulated study, providing a biologically meaningful model to explain flux data of both organisms in terms of the EM activation. The PEMA toolbox is freely available for non-commercial purposes on http://mseg.webs.upv.es., Research in this study was partially supported by the Spanish Ministry of Economy and Competitiveness and FEDER funds from the European Union through grants DPI2011-28112-C04-02 and DPI2014-55276-C5-1R. We would also acknowledge Fundacao para a Ciencia e Tecnologia for PhD fellowships with references SFRH/BD/67033/2009, SFRH/BD/70768/2010 and PTDC/BBB-BSS/2800/2012.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dynamic elementary mode modelling of non-steady state flux data

  • Folch-Fortuny, Abel
  • Teusink, Bas
  • Hoefsloot, Huub C.J.
  • Smilde, Age K.
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] A novel framework is proposed to analyse metabolic fluxes in non-steady state conditions, based on the new concept of dynamic elementary mode (dynEM): an elementary mode activated partially depending on the time point of the experiment., This research work was partially supported by the Spanish Ministry of Economy and Competitiveness under the project DPI2014-55276-C5-1R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization Alternatives for Robust Model-based Design of Synthetic Biological Circuits

  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
  • Pitarch, José Luis|||0000-0001-5356-6321
  • Vignoni, Alejandro|||0000-0001-9977-7132
  • Picó, Jesús|||0000-0003-4144-3521
  • Reynoso Meza, Gilberto
[EN] Synthetic biology is reaching the situation where tuning devices by hand is no longer possible due to the complexity of the biological circuits being designed. Thus, mathematical models need to be used in order, not only to predict the behavior of the designed synthetic devices; but to help on the selection of the biological parts, i.e., guidelines for the experimental implementation. However, since uncertainties are inherent to biology, the desired dynamics for the circuit usually requires a trade-off among several goals. Hence, a multi-objective optimization design (MOOD) naturally arises to get a suitable parametrization (or range) of the required kinetic parameters to build a biological device with some desired properties. Biologists have classically addressed this problem by evaluating a set of random Monte Carlo simulations with parameters between an operation range. In this paper, We propose solving the MOOD by means of dynamic programming using both a global multi-objective evolutionary algorithm (MOLA) and a local gradient-based nonlinear programming (NLP) solver. The performance of both alternatives is then checked in the design of a well-known biological circuit: a genetic incoherent feed-forward loop showing adaptive behavior. (C) 2016, IFAC (International Federation of Antomatic Control) Hosting by Elsevier Ltd. All rights reserved., The research leading to these results has received funding from the European Union (FP7/2007-2013 under grant agreement no604068), the Spanish Government (FEDER-CICYT DPI2011-524 28112-C04-01, DPI2014-55276-C5-1-R, DPI2015-70975-P) and the National Council of Scientific and Technologic Development of Brazil (BJT-304804/2014-2). Yadira Boada thanks also grant FPI/2013-3242 of the Universitat Politecnica de Valencia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

VIS/NIR hyperspectral imaging and N-way PLS-DA models for detection of decay lesions in citrus fruits

  • Folch Fortuny, Abel
  • Cubero-García, Sergio
  • Blasco Ivars, José
  • Prats-Montalbán, José Manuel|||0000-0001-6294-4486
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] In this work an N-way partial least squares regression discriminant analysis (NPLS-DA) methodology is developed to detect symptoms of disease caused by Penicillium digitatum in citrus fruits (green mould) using visible/near infrared (VIS/NIR) hyperspectral images. To build the discriminant model a set of oranges and mandarins was infected by the fungus and another set was infiltrated just with water for control purposes. A double cross-validation strategy is used to validate the discriminant models. Finally, permutation testing is used to select a few bands offering the best correct classification rates in the validation set. The discriminant models developed here can be potentially implemented in a fruit packinghouse to detect infected citrus fruits at their arrival from the field with affordable multispectral (3 5 channels) cameras installed in the packinglines., This research was partially funded by the Spanish Ministry of Science and Innovation through grants DPI2011-28112-C04-02 and DPI2014-55276-C05-1R, and by INIA through grant RTA2012-00062-C04-01. In all cases with the support of European FEDER funds. Authors thank Lluis Palou from the Centro de Tecnologia Postcosecha at the IVIA for the help and supervision in the innoculation process of the fruits.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Missing Data Imputation Toolbox for MATLAB

  • Folch Fortuny, Abel
  • Arteaga Moreno, Francisco Javier
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] Here we introduce a graphical user-friendly interface to deal with missing values called Missing Data Imputation (MDI) Toolbox. This MATLAB toolbox allows imputing missing values, following missing completely at random patterns, exploiting the relationships among variables. In this way, principal component anal- ysis (PCA) models are fitted iteratively to impute the missing data until convergence. Different methods, using PCA internally, are included in the toolbox: trimmed scores regression (TSR), known data regres- sion (KDR), KDR with principal component regression (KDR-PCR), KDR with partial least squares regression (KDR-PLS), projection to the model plane (PMP), iterative algorithm (IA), modified nonlinear iterative partial least squares regression algorithm (NIPALS) and data augmentation (DA). MDI Toolbox presents a general procedure to impute missing data, thus can be used to infer PCA models with missing data, to estimate the covariance structure of incomplete data matrices, or to impute the missing values as a preprocessing step of other methodologies., Research in this study was partially supported by the Spanish Ministry of Science and Innovation and FEDER funds from the European Union through grant DPI2011-28112-C04-02 and DPI2014-55276-C5-1 R, and the Spanish Ministry of Economy and Competitiveness through grant ECO2013-43353-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On-The-Fly Processing of continuous high-dimensional data streams

  • Vitale, Raffaele
  • Zhyrova, Anna
  • Fortuna, Joao F.
  • De Noord, Onno E.
  • Martens, Harald
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] A novel method and software system for rational handling of time series of multi-channel measurements is presented. This quantitative learning tool, the On-The-Fly Processing (OTFP), develops reduced-rank bilinear subspace models that summarise massive streams of multivariate responses, capturing the evolving covariation patterns among the many input variables over time and space. Thereby, a considerable data compression can be achieved without significant loss of useful systematic information. The underlying proprietary OTFP methodology is relatively fast and simple it is linear/bilinear and does not require a lot of raw data or huge cross-correlation matrices to be kept in memory. Unlike conventional compression methods, the approach allows the high-dimensional data stream to be graphically interpreted and quantitatively utilised in its compressed state. Unlike adaptive moving-window methods, it allows all past and recent time points to be reconstructed and displayed simultaneously. This new approach is applied to four different case-studies: (i) multi-channel Vis-NIR spectroscopy of the Belousov Zhabotinsky reaction, a complex, ill understood chemical process; (ii) quality control of oranges by hyperspectral imaging; (iii) environmental monitoring by airborne hyperspectral imaging; (iv) multi-sensor process analysis in the petrochemical industry. These examples demonstrate that the OTFP can automatically develop high-fidelity subspace data models, which simplify the storage/transmission and the interpretation of more or less continuous time series of high-dimensional measurements to the extent there are covariations among the measured variables., This research work was partially supported by the Spanish Ministry of Economy and Competitiveness under the project DPI2014-55276-C5-1R, Shell Global Solutions International B.V. (Amsterdam, The Netherlands), Idletechs AS (Trondheim, Norway), the Norwegian Research Council (Grant 223254) through the Centre of Autonomous Marine Operations and Systems (AMOS) at the Norwegian University of Science and Technology (Trondheim, Norway) and the Ministry of Education, Youth and Sports of the Czech Republic (CENAKVA project CZ.1.05/2.1.00/01.0024 and CENAKVA II project L01205 under the NPU I program). The authors want to acknowledge Prof. Bjorn Alsberg for providing the Vis-NIR equipment and the Laboratorio de Sistemas e Tecnologia Subaquatica of the University of Porto, the Hydrographic Institute of the Portuguese Navy and the University of the Azores for carrying out the REP15 exercise, during which the hyperspectral push broom image was collected.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

PFA toolbox: a MATLAB tool for Metabolic Flux Analysis

  • Morales, Yeimy
  • Bosque Chacón, Gabriel
  • Vehi, Josep
  • Llaneras, Francisco
  • Picó, Jesús|||0000-0003-4144-3521
Background: Metabolic Flux Analysis (MFA) is a methodology that has been successfully applied to estimate metabolic fluxes in living cells. However, traditional frameworks based on this approach have some limitations, particularly when measurements are scarce and imprecise. This is very common in industrial environments. The PFA Toolbox can be used to face those scenarios. Results: Here we present the PFA (Possibilistic Flux Analysis) Toolbox for MATLAB, which simplifies the use of Interval and Possibilistic Metabolic Flux Analysis. The main features of the PFA Toolbox are the following: (a) It provides reliable MFA estimations in scenarios where only a few fluxes can be measured or those available are imprecise. (b) It provides tools to easily plot the results as interval estimates or flux distributions. (c) It is composed of simple functions that MATLAB users can apply in flexible ways. (d) It includes a Graphical User Interface (GUI), which provides a visual representation of the measurements and their uncertainty. (e) It can use stoichiometric models in COBRA format. In addition, the PFA Toolbox includes a User s Guide with a thorough description of its functions and several examples. Conclusions: The PFA Toolbox for MATLAB is a freely available Toolbox that is able to perform Interval and Possibilistic MFA estimations., This research has been partially supported by the Spanish Government (FEDER-CICYT: DPI 2014-55276-C5-1-R). Yeimy Morales is grateful for the BR Grants of the University of Girona (BR2012/26). Gabriel Bosque Chacon is recipient of a doctoral fellowship from the Spanish Government (BES-2012-053772).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of maximum likelihood PCA missing data imputation

  • Folch Fortuny, Abel
  • Arteaga Moreno, Francisco Javier
  • Ferrer, Alberto|||0000-0001-7244-5947
Maximum likelihood principal component analysis (MLPCA) was originally proposed to incorporate measurement error variance information in principal component analysis (PCA) models. MLPCA can be used to fit PCA models in the presence of missing data, simply by assigning very large variances to the non-measured values. An assessment of maximum likelihood missing data imputation is performed in this paper, analysing the algorithm of MLPCA and adapting several methods for PCA model building with missing data to its maximum likelihood version. In this way, known data regression (KDR), KDR with principal component regression (PCR), KDR with partial least squares regression (PLS) and trimmed scores regression (TSR) methods are implemented within the MLPCA method to work as different imputation steps. Six data sets are analysed using several percentages of missing data, comparing the performance of the original algorithm, and its adapted regression-based methods, with other state-of-the-art methods., Research in this study was partially supported by the Spanish Ministry of Science and Innovation and FEDER funds from the European Union through grant DPI2011-28112-C04-02 and DPI2014-55276-C5-1R, and the Spanish Ministry of Economy and Competitiveness through grant ECO2013-43353-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Global stabilisation of continuous bioreactors: tools for analysis and design of feeding laws

  • De Battista, Hernán
  • Jamilis, M.
  • Garelli, Fabricio
  • Picó, Jesús|||0000-0003-4144-3521
[EN] This work revisits the dynamic behaviour of stirred continuous reactors in which a single bioreaction with unknown kinetics occurs. Conditions on the feeding strategy to avoid washing out the biomass and falling in batch operation are obtained. These conditions derive in a closed positively invariant region including the desired operating point. It is stated that no closed orbits may exist in this region and, furthermore, that no fixed point exists but on one of its borders. Therefore, global stability is achieved by finding a feeding law that fulfils the aforementioned invariant conditions and gives a single equilibrium for a first-order dynamics. These results are useful to determine the stability properties of different control laws and, more importantly, to design new ones. The main advantages of the proposed approach are its simplicity and that, differing from previous results, input saturation does not affect stability results. The potentiality of the developed tools is illustrated by means of classical and novel feeding laws. (C) 2017 Elsevier Ltd. All rights reserved., Financed by I216-2016 (UNLP), PICT2014-2394 (ANPCyT) and PIP112-2015-01-00837 (CONICET), Argentina; and by DPI2014-55276-C5-1-R MINECO/AEI/FEDER, UE. The material in this paper was not presented at any conference.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Engineered Control of Genetic Variability Reveals Interplay among Quorum Sensing, Feedback Regulation, and Biochemical Noise

  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
  • Vignoni, Alejandro|||0000-0001-9977-7132
  • Picó, Jesús|||0000-0003-4144-3521
[EN] Stochastic fluctuations in gene expression trigger both beneficial and harmful consequences for cell behavior. Therefore, achieving a desired mean protein expression level while minimizing noise is of interest in many applications, including robust protein production systems in industrial biotechnology. Here, we consider a synthetic gene circuit combining intracellular negative feed- back and cell-to-cell communication based on quorum sensing. Accounting for both intrinsic and extrinsic noise, stochastic simulations allow us to analyze the capability of the circuit to reduce noise strength as a function of its parameters. We obtain mean expression levels and noise strengths for all species under different scenarios, showing good agreement with system-wide available experimental data of protein abundance and noise in Escherichia coli. Our in silico experiments, validated by preliminary in vivo results, reveal significant noise attenuation in gene expression through the interplay between quorum sensing and negative feedback and highlight the differential role that they play in regard to intrinsic and extrinsic noise., his work was partially supported by the Spanish Government(CICYT DPI2014-55276-C5-1) and the European Union(FEDER). Y.B. thanks grant FPI/2013-3242 of UPV.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

PID controller tuning for unstable processes using a multi-objective optimisation design procedure

  • Reynoso-Meza, Gilberto
  • Carrillo Ahumada, J.
  • Boada-Acosta, Yadira Fernanda|||0000-0001-5677-2702
  • Picó, Jesús|||0000-0003-4144-3521
[EN] Multi-objective optimisation techniques have shown to be a useful tool for controller tuning applications. Such techniques are useful when: 1) it is difficult to find a controller with a desirable trade-off between conflictive objectives; or 2) it is valuable to extract an additional knowledge from the process by analysing track-off among possible controllers. In this work, we propose a. multi-objective optimisation design procedure for unstable process, using PID controllers. The provided examples show the usability of the procedure for this kind of process, sometimes difficult to control; comparison with existing tuning rule methods provide promising results for this tuning procedure. (C) 2016, IFAC (International Federation of Automatic Control) Hosting by Elsevier Ltd. All rights reserved., This work was partially supoted by projects FEDER-CICYT DPI2014-55276-C5-1 (Spain) and the fellowships FPI/2013-3242 (UPV, Spain), BJT-304804/2014-2 (CNpQ, Brazil). Second author wishes to thank to Universidad del Papaloapan by the approved project entitled Sintonizacin de controladores lineales optimo-robustos mediante algoritmos evolutivos y tecnicas de decision multi-criterio. Third author thanks the Santander Scholarship program (Investigacion-JPI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enabling network inference methods to handle missing data and outliers

  • Folch-Fortuny, Abel
  • Villaverde, A. F.
  • Ferrer, Alberto
  • Banga, Julio R.
12 pages, 3 figures, 2 tables, Background: The inference of complex networks from data is a challenging problem in biological sciences, as well as in a wide range of disciplines such as chemistry, technology, economics, or sociology. The quantity and quality of the data greatly affect the results. While many methodologies have been developed for this task, they seldom take into account issues such as missing data or outlier detection and correction, which need to be properly addressed before network inference. Results: Here we present an approach to (i) handle missing data and (ii) detect and correct outliers based on multivariate projection to latent structures. The method, called trimmed scores regression (TSR), enables network inference methods to analyse incomplete datasets by imputing the missing values coherently with the latent data structure. Furthermore, it substitutes the faulty values in a dataset by proper estimations. We provide an implementation of this approach, and show how it can be integrated with any network inference method as a preliminary data curation step. This functionality is demonstrated with a state of the art network inference method based on mutual information distance and entropy reduction, MIDER. Conclusion: The methodology presented here enables network inference methods to analyse a large number of incomplete and faulty datasets that could not be reliably analysed so far. Our comparative studies show the superiority of TSR over other missing data approaches used by practitioners. Furthermore, the method allows for outlier detection and correction, Research in this study was partially supported by the European Union through project BioPreDyn (FP7-KBBE 289434), and the Spanish Ministry of Science and Innovation and FEDER funds from the European Union through grants MultiScales (DPI2011-28112-C04-02, DPI2011-28112-C04-03), and SynBioFactory (DPI2014-55276-C5-1-R, DPI2014-55276-C5-2-R). AF Villaverde also acknowledges funding from the Xunta de Galicia through an I2C postdoctoral fellowship (I2C ED481B 2014/133-0)., Peer reviewed